Temperature-dependent Behavior Research Articles

Temperature-regulated gas adsorption on LTA zeolites: Observation of sorption isotherms for methane, hydrogen, nitrogen and carbon dioxide

Temperature-regulated gas adsorption of various zeolite LTAs with different cations of Cs2+, K+, Na+, and Ca2+ (namely, Cs-A, 3A, 4A, and 5A) was analysed in the presence of different gas molecules of H2, CO2, N2, and CH4 for pressures up to 800 kPa and temperatures ranging from 77.15 to 363.15 K. Over the range of test conditions, zeolite 5A (containing Ca2+ cations) exhibited the highest uptake at 800 kPa for CO2, H2, CH4, and N2, with capacity values of 5.69 mmol.g−1, 1.14 mmol.g−1, 6.60 mmol.g−1, and 6.10 mmol.g−1, at 298.15 K and 201.15 K respectively. Zeolite 4A (containing Na+ cations) exhibited 0.74 mmol.g−1 for H2 adsorption at 201.15 K, and 800 kPa. In contrast, pores were inaccessible to H2 on ion-exchange Cs-A zeolite at a temperature range of 77.15–343.15 K, due to larger cation Cs2+ (CsA) comparison with Na+ (4A). Interestingly, zeolite 3A (containing K+ cations) showed a negligible capacity for the larger gas molecules, CH4 and N2, ascribed to the pore space blocked by the larger K+ cations (relative to the smaller Na+ and Ca2+ cations). Zeolite 3A exhibited a temperature-dependent behaviour (i.e., presumably a “trapdoor” effect) with H2 wherein adsorption was negligible at 77.15 K, but was significant above approximately 200 K. For N2, zeolite 4A exhibits similar temperature-regulated adsorption characteristics (i.e., presumably a “trapdoor” mechanism as well). These zeolite materials used in various temperature swing processes could be particularly beneficial in natural hydrogen production (with H2/N2 separation with 3A), the production of synthetic fuels from CO2/H2 mixtures (with both 3A and 4A), CO2 capture from waste streams, and applications for H2/N2 separation.

Effects of temperature on the anisotropic mechanical properties and failure mechanisms of Sheet Molding Compounds

Sheet Molding Compounds (SMC) are widely used in many industries. Due to their high in-mold flow, fibers tend to align during the component processing and generate anisotropic mechanical properties. Besides, being SMCs thermoset composites, their application in high temperature environments often results to be of interest. In this research, the fiber orientation and temperature-dependent mechanical behavior and failure mechanisms were studied. First, materials were compression molded into plates, promoting fiber orientation. Then, the materials’ orientation-dependent viscoelastic behavior was analyzed by Dynamic Mechanical Analysis, and their anisotropy level was assessed at quasi-static tensile, bending and compression modes at 23 °C and 130 °C. Finally, the failure mechanisms were inspected by confocal microscopy to evaluate the influence of temperature and fiber orientation on them. The results demonstrate how the temperature influences the material’s mechanical performance and their anisotropic behavior, especially at 45°. Likewise, temperature alters failure mechanisms, by triggering the fiber-matrix interface failure.

Estimating equivalent elastic properties of frozen clay soils using an XFEM-based computational homogenization

This study addresses the challenge of estimating the elastic properties of heterogeneous frozen clay soils by introducing a comprehensive approach that combines analytical and numerical models. The frozen clay soil is treated as a mixture composed of frozen clay-water composites and nonclay mineral inclusions. An inversion algorithm is employed to deduce the elastic properties of the matrix (clay-water composites) of two artificially frozen sandy clay samples with known temperature-dependent elastic properties. Subsequently, a two-dimensional numerical simulation using the eXtended Finite Element Method (XFEM) is conducted to carry out numerical homogenization by considering the imperfect bond among frozen clay-water composites and nonclay minerals. The numerical homogenization model offers insights into the temperature-dependent behavior of the interface stiffness parameter. The numerical homogenization results are compared with conventional numerical homogenization approaches like the FEM, which rigidly defines the bonding between inclusions and the matrix. The comparison indicates that the neglect of imperfect bonds among clay-water composites and nonclay minerals will lead to unrealistic outcomes in cases with a high fraction of inclusions. This integrated approach advances the understanding and prediction of elastic properties of frozen clay soils by considering their heterogeneous nature.

Capacity building in porous materials research for sustainable energy applications.

The project aimed to develop porous materials for sustainable energy applications, namely, hydrogen storage, and valorization of biomass to renewable fuels. At the core of the project was a training programme for Africa-based researchers in (i) the exploitation of renewable locally available raw materials; (ii) the use of advanced state-of-the-art techniques for the design and synthesis of porous materials (zeolites and metal-organic frameworks (MOFs)) for energy storage; and (iii) the valorization of sustainable low-value feedstock to renewable fuels. We found that compaction of the UiO-66 MOF at high pressure improves volumetric hydrogen storage capacity without any loss in gravimetric uptake, and experimentally demonstrated the temperature-dependent dynamic behaviour of UiO-66, which allowed us to propose an activation temperature of ≤ 150°C for UiO-66. Co-pelletization was used to fabricate UiO-66/nanofibre monoliths as hierarchical porous materials with enhanced usable (i.e. deliverable) hydrogen storage capacity. We clarified the use of naturally occurring kaolin as a source of silica and alumina species for zeolite synthesis. The kaolin-derived zeolite X was successfully used as a catalyst for the transesterification of Jatropha curcas oil (from non-edible biomass) to biodiesel. We also prepared porous composites (i.e. carbon/UiO-66, organoclay/UiO-66 and zeolite/carbon) that were successfully applied in electrochemical sensing.

Solid-State Lithium-Ion Superionic Electrolytes with Reduced Moisture Sensitivity

The remarkable safety and high energy density of solid-state batteries (SSBs) created significant advantages in the development of next-generation energy storage. The properties of these batteries are highly dependent on the characteristics of solid-state electrolytes (SSEs), making them a crucial material in the development of such batteries. Following diverse principles of material design, lithium halide SSEs, particularly Li3InCl6, open new opportunities in the development of SSBs due to their unique properties including broad electrochemical stability window, high lithium-ion conductivity, and excellent deformability. Through a mechano-thermal synthesis approach, Li3InCl6 demonstrates substantial ionic conductivity at room temperature. We studied the temperature-dependent behavior of Li3InCl6 by using in-situ/operando techniques such as XRD and XPS. However, its susceptibility to moisture poses a significant challenge for practical implementation in SSBs. To overcome this limitation, this research is focused on a novel solution: hafnium doping of Li3InCl6. Integrating hafnium into the Li3InCl6 structure results in a substantial improvement in electrochemical performance. The Li2.6In0.6Hf0.4Cl6 solid-state electrolyte not only showcases heightened ionic conductivity but also demonstrates improved resistance to moisture. The achieved ionic conductivity reaches approximately 1 mS cm-1, marking a significant 3.5-fold increase compared to Li3InCl6. Noteworthy is the fact that, after 5 hours of exposure to air with 15% humidity, the observed reduction in ionic conductivity for Li2.6In0.6Hf0.4Cl6 is 37%, a notably lower decrease compared to the 57% reduction seen in Li3InCl6.The efficacy of hafnium doping provides a crucial advancement in the field of solid-state electrolytes, promising a transformative impact on next-generation energy storage systems.

Investigating Temperature-Dependent Dynamics of SEI Growth and Battery Degradation

Several studies have contributed to the current understanding of the temperature-dependent behavior of solid-electrolyte interphase (SEI) formation in lithium-ion batteries and its impact on battery capacity and lifespan. Liu et al. developed a thermal-electrochemical model that revealed the complex interplay between diffusivity, reaction kinetics, and temperature on SEI growth1. Leng et al. presented an electrochemistry-based electrical model to examine the temperature's effect on battery aging2. Alipour et al. reviewed temperature-dependent electrochemical properties3, while Lubhani Mishra et al. provided a detailed physics-based analysis of battery degradation and temperature inhomogeneities4. These studies collectively indicate higher temperatures accelerating and promoting growth of compact and less permeable SEI structures leading to an increase in capacity loss and cell resistance, and lower temperatures resulting in slow ionic transport through the SEI also causing higher ohmic loss. In the present work, we study SEI growth and resulting effect on battery capacity fade using continuum scale modeling under the assumption of constant battery cell temperature as well as considering actual dynamically changing temperature data from experiments. SEI growth under these two considerations is compared and the comparison is used in determining scenarios where considering dynamically varying temperature is crucial for accuracy. The detailed analysis of the internal states from the simulation results contributes to the understanding of the effect of the thermal dynamics on battery cell degradation due to SEI growth. To achieve these objectives, a physics-based model, specifically the Single Particle Model (SPM), is utilized. The model uses temporal temperature data obtained from past experimental studies as well as temperature dependent properties of SEI provided in the literature as inputs for this investigation. The ultimate aim of this study is to better understand how temperature influences SEI characteristics, thereby contributing to improved battery performance and longevity across diverse thermal environments. References Liu, L., Park, J., Lin, X., Sastry, A. M., & Lu, W. (2014). A thermal-electrochemical model that gives spatial-dependent growth of solid electrolyte interphase in a Li-ion battery. Journal of power sources, 268, 482-490.Leng, F., Tan, C. M., & Pecht, M. (2015). Effect of temperature on the aging rate of Li-ion battery operating above room temperature. Scientific reports, 5(1), 12967.Alipour, M., Ziebert, C., Conte, F. V., & Kizilel, R. (2020). A review on temperature-dependent electrochemical properties, aging, and performance of lithium-ion cells. Batteries, 6(3), 35.Mishra, L., Subramaniam, A., Jang, T., Garrick, T. R., & Subramanian, V. R. (2022, October). Model Development for Temperature-Dependent Degradation in Large Format Lithium-Ion Batteries. In Electrochemical Society Meeting s 242 (No. 28, pp. 1075-1075). The Electrochemical Society, Inc.

Diffusion and structure of propylene carbonate-metal salt electrolyte solutions for post-lithium-ion batteries: From experiment to simulation.

The diffusion of cations in organic solvent solutions is important for the performance of metal-ion batteries. In this article, pulsed field gradient nuclear magnetic resonance experiments and fully atomistic molecular dynamic simulations were employed to study the temperature-dependent diffusive behavior of various liquid electrolytes representing 1M propylene carbonate solutions of metal salts with bis(trifluoromethylsulfonyl)imide (TFSI-) or hexafluorophosphate (PF6-) anions commonly used in lithium-ion batteries and beyond. The experimental studies revealed the temperature dependence of the diffusion coefficients for the propylene carbonate (PC) solvent and for the anions following an Arrhenius type of behavior. It was observed that the PC molecules are the faster species. For the monovalent cations (Li+, Na+, K+), the PC solvent diffusion was enhanced as the cation size increased, while for the divalent cations (Mg2+, Ca2+, Sr2+, Ba2+), the opposite trend was observed, i.e., the diffusion coefficients decreased as the cation size increased. The anion diffusion in LiTFSI and NaTFSI solutions was found to be similar, while in electrolytes with divalent cations, a decrease in anion diffusion with increasing cation size was observed. It was shown that non-polarizable charge-scaled force fields could correspond perfectly to the experimental values of the anion and PC solvent diffusion coefficients in salt solutions of both monovalent (Li+, Na+, K+) and divalent (Mg2+, Ca2+, Sr2+, Ba2+) cations at a range of operational temperatures. Finally, after calculating the radial distribution functions between cations, anions, and solvent molecules, the increase in the PC diffusion coefficient established with the increase in cation size for monovalent cations was clearly explained by the large hydration shell of small Li+ cations, due to their strong interaction with the PC solvent. In solutions with larger monovalent cations, such as Na+, and with a smaller solvation shell of PC, the PC diffusion is faster due to more liberated solvent molecules. In the salt solutions with divalent cations, both the anion and the PC diffusion coefficients decreased as the cation size increased due to an enhanced cation-anion coordination, which was accompanied by an increase in the amount of PC in the cation solvation shell due to the presence of anions.

Thermoresponsive On-Demand Adhesion and Detachment of a Polyurethane-Urea Bioadhesive.

The development of bioadhesives with strong adhesion and on-demand adhesion-detachment behavior is still critically important and challenging for facilitating painless and damage-free removal in clinical applications. In this work, for the first time, we report the easy fabrication of novel polyurethane-urea (PUU)-based bioadhesives with thermoresponsive on-demand adhesion and detachment behavior. The PUU copolymer was synthesized by a simple copolymerization of low-molecular-weight, hydrophilic, and biocompatible poly(ethylene glycol), glyceryl monolaurate (GML, a special chain extender with a long side hydrophobic alkyl group), and isophorone diisocyanate (IPDI). Here, GML was expected to not only adjust the temperature-dependent adhesion behavior but also act as an internal plasticizer. By simple adjustment of the water content, the adhesion strength of the 15 wt % water-containing PUU film toward porcine skin is as high as 55 kPa with an adhesion energy of 128 J/m2 at 37 °C. The adhesion strength dramatically decreases to only 3 kPa at 10 °C, exhibiting switching efficiency as high as 0.95. Furthermore, the present PUU-based adhesive also shows good on-demand underwater adhesion and detachment with a cell viability close to 100%. We propose that biomaterial research fields, especially novel PUU/polyurethane (PU)-based functional materials and bioadhesives, could benefit from such a novel thermoresponsive copolymer with outstanding mechanical and functional performances and an easy synthesis and scaled-up process as described in this article.

Temperature-Induced Nanoarchitectonics of Monolayer Self-Assembly of Heterocoronene-Based Discotic Liquid Crystals.

Enhancing molecular self-assembly at the monolayer level offers significant potential for various applications. For monolayers made of π-conjugated discotic liquid crystal (DLC) molecule nanowires, achieving precise separation and alignment of these nanowires has been a long-standing challenge. This research explores an approach using the manipulation of subphase temperature and surface pressure within a Langmuir trough to control molecular nanowire separation. We observe notable temperature-dependent behavior: as the temperature increases from 5 to 30 °C, the monolayer collapse pressure rises steadily. In contrast, temperatures from 35 to 50 °C exhibit an initial small plateau with a nonzero slope that becomes more distinct with rising temperature. Our study of Langmuir-Blodgett (LB) films provides crucial insights into the monolayer's structure. At lower temperatures, the LB films show coalesced molecular nanowires, whereas at higher temperatures, the DLC nanowires separate and form an interconnected network. Remarkably, upon compression, this network transforms into a compact, highly uniform monolayer. To explain these temperature-dependent behaviors, we examine the area relaxation curves, which indicate a two-step molecular loss mechanism involving desorption and monolayer collapse due to the nucleation and growth of critical nuclei. This extensive study offers valuable insights into the dynamic interaction of the temperature, surface pressure, and molecular assembly, enhancing our understanding of the fundamental processes in monolayer self-assembly.

Defect level induced negative thermal quenching of β-Ba3LuAl2O7.5: Yb3+, Er3+ phosphor

Temperature-dependent behavior of phosphors has recently attracted significant research attention. This is due to the widespread applications of phosphors. Unfortunately, the thermal quenching effect in many phosphors greatly limits their performance at high temperatures. Herein, negative thermal quenching phosphor β-Ba3LuAl2O7.5: 0.3Yb3+, 0.03Er3+ is synthesized using the high-temperature solid-state method. X-ray Rietveld refinement and EPR results indicate the defect state of oxygen vacancy. Temperature-dependent upconversion luminescence spectra demonstrate that the green and red emission intensities increase with temperature to reach maximums at 398 K and 348 K respectively. Diffuse reflectance spectrum and downshifting luminescence spectrum prove that the defect state is near the 4F7/2 state of Er3+ ions. The defect state traps electrons at room temperature and releases them to populate the 4F7/2 state of Er3+ ion at elevated temperatures to cause the observed thermal enhancement of upconversion luminescence. This material's negative thermal quenching effect makes it a suitable candidate for applications in displays and anti-counterfeiting.

Nano-, micro- and macro-indentation tests of thermal spray WC-Ni coatings with lamellar microstructure at different particle deposition temperatures

The mechanical properties of WC-Ni coatings by HVOF thermal spraying were comprehensively evaluated by indentation tests at a wide load range of 10−1-103 N, i.e. nano-, micro- and macro-indentations. The correlation between process parameters and coating microstructure and mechanical properties was characterized via particle deposition temperature. The coating microstructure changes in reduced porosity, enhanced WC phase decomposition and better splats flattening were correlated to the particle deposition temperature rising. A porosity divergence between coating surface and cross-section was found as a quantitative anisotropy indicator to coating intrinsic lamellar microstructure formed by the splats flattening and piling up. Considering the lamellar microstructure, indentation responses on coating surface and cross-section were compared for hardness and elastic modulus evaluation below 3 N. The surface hardness is higher than that of cross-section, and both increased correlatively to the particle deposition temperature rising except for the almost constant surface hardness below 1 N. An analogous particle temperature-dependent behavior was also manifested for the elastic modulus by nano-indentation below 1 N. Interestingly, the elastic modulus by coating surface micro-indentation at 30 N presented identical particle temperature dependence to that by coating cross-section nano-indentation, both consistently representing the overall coating elastic modulus change trend verified by non-destructive ultrasonic test. Indentation fracture toughness on coating surface under 1.96 kN and on coating cross-section under 49 N was comparatively evaluated, and the values had a reverse trend of dependence on the particle deposition temperature. The particle-deposition-temperature dependent mechanical properties were interpreted by the coating intra-splats and inter-splats defects reduction with enhanced carbide-metal bonding essentially determined by the melting state of the metal binder phase, providing an insight to utilize indentation tests for characterizing thermal spray coatings.

Thermo-mechanical behavior of sandstone joints: Findings from direct shear tests

Rock masses typically contain joints and defects affecting their safety and stability under compression, shear, or tension. The shear strength of these discontinuities, influenced by environmental factors like temperature, is critical in deep rock engineering. This study conducted direct shear tests on sandstone joints at room temperature (RT) and after thermal treatment at 250 °C and 500 °C. The behavior under compressive and shear forces was investigated by using the direct shear test. The results showed that compressive and shear properties improved at 250 °C but deteriorated following thermal treatment at 500 °C. Peak shear strength before and after thermal treatment closely followed Patton's bilinear failure criterion. As intact asperities were sheared under normal stress of 0.75MPa, the residual shear strength was less affected by temperature than peak shear strength. The shear strength of intact asperities increased by 8.8% following thermal treatment at 250 °C and decreased by 4.3% at 500 °C. The joint closure, normal stress, and stiffness were consistent with a modified Bandis et al. (1983) criterion. Increasing the thermal treatment temperature from RT to 250 °C and 500 °C changed maximum joint closure from 0.201 to 0.125and 0.301 mm, and subsequently, the initial normal stiffness from 8 to 19.6 and 6.62MPa/mm, respectively. These findings offer valuable insights into the temperature-dependent behavior of sandstone joints, aiding the design and maintenance of deep underground structures. This research is particularly relevant to engineering geology, where understanding the thermo-mechanical behavior of rock joints is essential for projects such as geothermal energy extraction and the storage of nuclear waste. The results can improve the safety and efficiency of geological engineering practices in thermally active environments.

Temperature-dependent acoustic emission characteristics and statistical constitutive model of granite under uniaxial compression

Understanding the temperature-dependent mechanical behavior and fracture characteristics of granite is crucial for many engineering projects. In this study, the real-time temperature curves of granite specimens were obtained during the heating and cooling process, and the thermal treatment tests were conducted. The physical properties of the specimen before and after thermal treatment, including mass, volume, and P-wave velocity, were measured. The acoustic emission (AE) signal in the uniaxial compression is monitored. The results indicate that the physical properties of granite deteriorate with temperature, while the mechanical properties show two effects of thermal strengthening and thermal weakening. This phenomenon is comprehensively analyzed by literature statistical data and optical microscopic observation. Furthermore, the AE characteristic is strongly dependent on temperature. High temperature induces more AE ring count to appear in the early stage of loading. As the temperature increases, the crack initiation stress decreases and the table crack propagation stage becomes longer. The attenuation of high-frequency signals and the enhancement of low-frequency signals are related to the development and interaction mechanism of thermally-induced crack and stress-induced crack. At 600 °C, the global b-value increases significantly. Meanwhile, the evolution of dynamic b-value helps explain the failure process of granite under axial load after thermal treatment. In addition, a new thermo-mechanical damage statistical constitutive model of granite considering temperature effects is proposed by introducing AE parameters. The main advantages of this model can well fit the nonlinear behavior of granite in the early loading stage after thermal treatment, and reflect the failure process of granite before the peak value.

Brillouin Biosensing of Viscoelasticity across Phase Transitions in Ovine Cornea.

Noninvasive in situ monitoring of viscoelastic characteristics of corneal tissue at elevated temperatures is pivotal for mechanical property-informed refractive surgery techniques, including thermokeratoplasty and photorefractive keratectomy, requiring precise thermal modifications of the corneal structure during these surgical procedures. This study harnesses Brillouin light scattering spectroscopy as a biosensing platform to noninvasively probe the viscoelastic properties of ovine corneas across a temperature range of 25-64 °C. By submerging the tissue samples in silicone oil, consistent hydration and immiscibility are maintained, allowing for their accurate sensing of temperature-dependent mechanical behaviors. We identify significant phase transitions in the corneal tissue, particularly beyond 40 °C, likely due to collagen unfolding, marking the beginning of thermal destabilization. A subsequent transition, observed beyond 60 °C, correlates with collagen denaturation. These phase transformations highlight the cornea's sensitivity to both physiologically reversible and irreversible viscoelastic changes induced by mild to high temperatures. Our findings underscore the potential of the Brillouin biosensing technique for real-time diagnostics of corneal biomechanics during refractive surgeries to attain optimized therapeutic outcomes.

Microstructure and mechanical properties of CoCrFeNiAl0.5Ti0.1 high entropy alloy rod

In this study, we investigated the microstructural features and mechanical behavior of a forged CoCrFeNiAl0.5Ti0.1 high-entropy alloy (HEA) rod with a 21 mm diameter. Analysis shows that the alloy comprises of a face-centered cubic (FCC) matrix with Ni2AlTi precipitates. Significantly, the Ni2AlTi precipitates demonstrate a modulus of approximately 162 GPa and a hardness of around 720 HV, markedly higher than the FCC matrix's modulus of 151 GPa and hardness of 425 HV. Mechanical testing reveals pronounced temperature-dependent behavior. At room temperature, the alloy exhibits a tensile strength of 1146 MPa and an elongation of 16.7 %. This strength rises to 1204 MPa with an 18.3 % elongation at 200 K, and further escalates to 1423 MPa with a 14.2 % elongation at 77 K, indicating superior mechanical properties at lower temperatures. Conversely, at elevated temperatures, the strength decreases, maintaining above 700 MPa at 873 K but falling to about 160 MPa at 1073 K. These findings highlight the significant impact of temperature on the mechanical performance of CoCrFeNiAl0.5Ti0.1 HEA, suggesting potential applications in varied environments.

Investigating the dielectric characteristics, electrical conduction mechanisms, morphology, and structural features of mullite via sol-gel synthesis at low temperatures

This research explores the fabrication of mullite precursor powder utilizing the sol-gel process at low temperatures. Silicon tetraethoxide (Si(C2H5O)4) and aluminum nitrate nonahydrate (Al(NO3)3.9H2O) were employed as the sources of SiO2 and Al2O3 oxides, respectively. Various analytical techniques, such as Fourier transform infrared spectroscopy (FTIR), thermogravimetry (TG), dilatometry, differential thermal analysis (DTA), and X-ray powder diffractometer (XRD), were utilized to investigate the formation and crystallization of the amorphous powder. The microstructure of specimens sintered at 1600 °C for 1 h was examined utilizing scanning electron microscopy (SEM). Measurements of hardness (HV) and coefficient of thermal expansion (CTE) were conducted on mullite samples heated to 1600 °C and then cooled, revealing an increase in HV from 888 to 1000 HV as the sintering temperature rose from 1500 to 1600 °C. The CTE of mullite within the temperature range of 50–1300 °C was determined as 5.23 × 10−6/°C. Additionally, the dielectric and electrical characterization of mullite was analyzed utilizing complex impedance spectroscopy at a frequency of 0.1–106 Hz and conductivity measurements over a temperature range of 40–400 °C. The real and imaginary parts of the dielectric permittivity exhibited frequency-dependent and temperature-dependent behaviors. Significantly, the observed variations in the imaginary component of the modulus and impedance maximum frequency point to a relaxation process that is not Debye-type, with calculated activation energies (Ea) consistent across different methods.

Temperature- and Rate-Dependent Fracture in Disulfide Vitrimers.

The fracture behaviors of disulfide vitrimers are highly rate-dependent. Our investigation revealed that the temperature-dependent fracture behaviors of disulfide vitrimers cannot be entirely explained by a simple time-temperature superposition model. This Letter explores the impact of the dynamic nature of molecular defects on the temperature- and rate-dependent fracture behaviors of disulfide vitrimers. Considering that the high cross-linking density remains constant during the associated bond exchange reaction, we identify loop defects in the network as the primary dynamic defects. By employing small amplitude oscillatory shear, we measured the loop defect fraction in EPS25 disulfide vitrimers at varied temperatures, revealing an increased presence of loop defects at elevated temperatures. Furthermore, our findings indicate that the temperature-dependent fracture behaviors are attributed to the temperature-dependent number of loop defects in disulfide vitrimers.

A periodic micromechanical model for the rate- and temperature-dependent behavior of unidirectional carbon fiber-reinforced PVDF

The rate- and temperature-dependent mechanical behavior of unidirectional carbon fiber-reinforced polyvinylidene fluoride (PVDF) is investigated through uniaxial tension and compression experiments under various off-axis loading conditions. To improve the understanding of the behavior of the composite, a 3D micromechanical model is developed. Microscopic analyses are used to characterize the geometrical properties of the UD composite at the fiber length-scale. These properties are used to construct a periodic 3D representative volume element (RVE). In combination with periodic boundary conditions, uniaxial macroscopic deformation (in any possible direction) is applied to the RVE to accurately and efficiently model off-axis loading. The rate- and temperature-dependent behavior of the PVDF matrix is accurately described using an elasto-viscoplastic constitutive model. The finite element simulations of uniaxial tension and compression tests are compared to the experimental data and the micromechanical response is analyzed. The micromechanical model accurately describes the rate-dependent macroscopic behavior of unidirectional carbon fiber-reinforced PVDF for various off-axis loading directions at different temperatures. Analysis of the local matrix response in the RVE reveals the influence of the matrix on the macroscopic behavior of the composite.

Optimizing TCAD Model and Temperature-Dependent Analysis of Pt/AlN Schottky Barrier Diodes for High-Power and High-Temperature Applications

This research presents a comprehensive investigation and optimization of the Pt/AlN Schottky Barrier diode (SBD) using technology computer-aided design (TCAD) modeling. The study explores the electrical characteristics of AlN SBDs with various metal contacts, including Aluminum (Al), Silver (Ag), Tungsten (W), Gold (Au), Nickel (Ni), and Platinum (Pt). Through the comparative analyses of different metal/AlN Schottky contacts, the Pt/AlN structure emerges as the most promising due to its superior barrier height and lower leakage current. At [Formula: see text]K, the diode demonstrates a barrier height of 2.72[Formula: see text]V, a nearly ideal leakage current of 0.046[Formula: see text]pA, and a breakdown voltage of 363[Formula: see text]V. The research extends to examining the temperature-dependent electrical behavior of Pt/AlN Schottky diodes, particularly for high-power and high-temperature applications. Analysis carried out across temperatures ranging from [Formula: see text]K to [Formula: see text]K reveals a trend of increasing ON resistance and consistently lower leakage current with rising temperature. Importantly, the study indicates that the impact of temperature on the barrier height and breakdown voltage of the diode is negligible, thus rendering it suitable for high-temperature operation. Leveraging the unique properties of AlN as an ultra-wide bandgap material within the III-V compound semiconductor family, this research provides valuable insights into the potential applications of Pt/AlN Schottky contact. The study highlights that the Pt/AlN Schottky contact is effective not only for high-power, high-temperature SBDs but also as superior metal/semiconductor gate contacts for field-effect transistors (FETs). Their suitability is attributed to their ability to handle high voltages, minimize reverse leakage current, and demonstrate improved thermal stability.

Thermal Properties of Athermal Granular Materials.

Dry granular materials consist of a vast ensemble of discrete solid particles interacting through complex frictional forces at the contact points. The particles are so large that these systems are believed to be completely athermal. Here, we arrest the dynamics of a flowing granular material in a steady-state-flow configuration, enabling an isolated examination of aging at the particle contacts without granular rearrangements. Our findings reveal that the evolution of interparticle forces within the arrested athermal granular network results in the spontaneous increase of the system's yield stress. This strengthening process is logarithmic in time with a rate that depends on the temperature. We demonstrate that the material's stress relaxation exhibits similar time- and temperature-dependent behavior, suggesting a shared origin for aging and stress relaxation in these systems governed by thermal molecular processes at the scale of the grain contacts.