Sewage Treatment Research Articles

Re-assessment of monoclonal antibodies against diclofenac for their application in the analysis of environmental waters.

The non-steroidal anti-inflammatory drug (NSAID) diclofenac (DCF) is an important environmental contaminant occurring in surface waters all over the world, because, after excretion, it is not adequately removed from wastewater in sewage treatment plants. To be able to monitor this pollutant, highly efficient analytical methods are needed, including immunoassays. In a medical research project, monoclonal antibodies against diclofenac and its metabolites had been produced. Based on this monoclonal anti-DCF antibody, a new indirect competitive enzyme-linked immunosorbent assay (ELISA) was developed and applied for environmental samples. The introduction of a spacer between diclofenac and the carrier protein in the coating conjugate led to higher sensitivity. With a test midpoint of 3 μg L-1 and a measurement range of 1-30 μg L-1, the system is not sensitive enough for direct analysis of surface water. However, this assay is quite robust against matrix influences and can be used for wastewater. Without adjustment of the calibration, organic solvents up to 5%, natural organic matter (NOM) up to 10 mg L-1, humic acids up to 2.5 mg L-1, and salt concentrations up to 6 g L-1 NaCl and 75 mg L-1 CaCl2 are tolerated. The antibody is also stable in a pH range from 3 to 12. Cross-reactivity (CR) of 1% or less was determined for the metabolites 4'-hydroxydiclofenac (4'-OH-DCF), 5-hydroxydiclofenac (5-OH-DCF), DCF lactam, and other NSAIDs. Relevant cross-reactivity occurred only with an amide derivative of DCF, 6-aminohexanoic acid (DCF-Ahx), aceclofenac (ACF) and DCF methyl ester (DCF-Me) with 150%, 61% and 44%, respectively. These substances, however, have not been found in samples. Only DCF-acyl glucuronide with a cross-reactivity of 57% is of some relevance. For the first time, photodegradation products were tested for cross-reactivity. With the ELISA based on this antibody, water samples were analysed. In sewage treatment plant effluents, concentrations in the range of 1.9-5.2 μg L-1 were determined directly, with recoveries compared to HPLC-MS/MS averaging 136%. Concentrations in lakes ranged from 3 to 4.4 ng L-1 and were, after pre-concentration, determined with an average recovery of 100%.

Three-dimensional NiO/Ni self-floating porous composite materials for efficient solar interfacial evaporation

The scarcity of freshwater resources and energy crisis are major challenges to the progress of human society. Recently, solar-driven interfacial water evaporation utilizes photothermal conversion materials to convert solar energy into thermal energy, which possesses great application potential in seawater desalination and sewage treatment. Here, we fabricated porous nickel sponge (NSP) composite photothermal material (NiO-NSP) containing abundant NiO nanoneedles array. This in situ-grown NiO with enhanced bonding between photothermal material and substrate can be used as a solar absorber directly without consuming additional photothermal material compared to conventional coating and cladding on the carrier surface. Due to the multi-scattering induced light trapping effect of the semiconductor NiO nanoneedles array on the surface of nickel fibers, resulting in light absorption up to 96.5 %. NiO-NSP evaporators have an abundance of interconnected porous channels for water supply, which results in strong capillary action to pump water to the evaporation interface efficiently. Moreover, the highly dispersed nanoneedles array expand the evaporation surface area. Consequently, the NiO-NSP evaporator delivers an excellent evaporation rate of 1.78 kg m−2 h−1 and a photothermal conversion efficiency of 84.7 % at one sun radiation. In addition, the micron-sized porous mesh structure of NiO-NSP dissolve salt crystals and diffuse them downward into the bulk brine, exhibiting excellent salt resistance and remarkable seawater desalination stability. Moreover, NiO-NSP solar evaporators has been demonstrated to possess excellent ability to purify dye and heavy metal ion wastewater. Therefore, the NiO-NSP high-performance evaporator produced by straightforward process proved to be suitable for solar seawater desalination and wastewater purification.

Design of a sustainable system for wastewater treatment and generation of biofuels based on the biomass of the aquatic plant Eichhornia Crassipes

Colombia’s continuous contamination of water resources and the low alternatives to produce biofuels have affected the fulfillment of the objectives of sustainable development, deteriorating the environment and affecting the economic productivity of this country. Due to this reality, projects on environmental and economic sustainability, phytoremediation, and the production of biofuels such as ethanol and hydrogen were combined. The objective of this article was to design and develop a sustainable system for wastewater treatment and the generation of biofuels based on the biomass of the aquatic plant Eichhornia crassipes. A system that simulates an artificial wetland with live E. crassipes plants was designed and developed, removing organic matter contaminants; subsequently, and continuing the sustainability project, bioreactors were designed, adapted, and started up to produce bioethanol and biohydrogen with the hydrolyzed biomass used in the phytoremediation process, generating around 12 g/L of bioethanol and around 81 ml H2/g. The proposed research strategy suggests combining two sustainable methods, bioremediation and biofuel production, to preserve the natural beauty of water systems and their surroundings.

Investigation of odor pollution by utilizing selected ion flow tube mass spectrometry (SIFT-MS) and principal component analysis (PCA).

Odor pollution, also referred to as odor nuisance, is a growing environmental concern that is significantly associated with mental health. Once emitted into the air, the concentration of odorous substances varies considerably with wind conditions, leading to difficulties in timely sampling. In the present study, we employed selected ion flow tube mass spectrometry (SIFT-MS) to measure 22 odor-producing molecules continuously in an urban-rural complex city. In addition, we applied statistical analyses, principal component analysis (PCA), and a conditional probability function (CPF) to the datasets obtained from SIFT-MS to identify the odor characteristics at two study sites. At site A, odorants related to livestock farming and industry showed high factor loadings on principal components (PCs) from the PCA. In contrast, we estimated that the odorous gaseous chemicals affecting site B were closely related to sewage treatment and municipal solid waste disposal. Similar CPF patterns of grouped substances from the PCA supported the association between potential odor sources and specific odorants at site B, which helped estimate possible source locations. Consequently, our findings indicate that continuous monitoring of odorous substances using SIFT-MS can be an effective way to provide sufficient information on odor-producing molecules, leading to the clear identification of odor characteristics despite the high variability of odorous substances.

Discrete Dynamic System Modeling for Simulated Moving Bed Processes

Although the simulated moving bed (SMB) process boasts advantages such as high productivity and low consumption, the cost of obtaining optimized parameters through practical experiments to control the separation process can be enormous due to its complex nonlinear characteristics. Consequently, the successful transformation of the SMB separation process into a mathematical dynamic model for computer simulation would greatly reduce the research costs associated with experimental studies. In this study, the Crank–Nicolson method was employed to discretize and dynamize the SMB process, enabling the simulation of processes under both linear and Langmuir isotherms. The results of the simulation experiments demonstrated the feasibility and high efficiency of this approach, thereby establishing a solid foundation for further advancements in online control strategies.

Distribution characteristics and investigation evaluation of ammonia nitrogen in the soil and groundwater of a chemical plant

ABSTRACT In this study, we analyzed the distribution characteristics of ammonia nitrogen, and evaluated the pollution status of the soil and groundwater in this legacy site. The results revealed that the concentration of ammonia nitrogen in the soil ranged from 2.36 to 32.7 mg/kg, and the areas with higher ammonia nitrogen concentration were the compression workshop, conversion workshop, sewage treatment area, and slag yard, the concentration of ammonia nitrogen in these areas ranged from 10.1 to 32.7 mg/kg. The groundwater ammonia nitrogen concentration ranged from 0.04 to 1.47 mg/L, the average value was 0.526 mg/L. Soil and groundwater ammonia nitrogen pollution in the plant area was mainly attributed to the node leakage of waste water pipes, and the investigation and evaluation results revealed that the soil test results of this site are consistent with the corresponding screening values. As the groundwater in this site is not used for drinking and other purposes, its risk to human health is considered acceptable. The detection indicators of groundwater in some plots exceed the Class III or IV standards, so long-term monitoring and retrospective risk assessment are the focus of future risk management and control of the plots.

Impact of Bisphenol‐A in the environment and its removal through biological agents: A review

AbstractEndocrine‐disrupting chemicals (EDCs) are synthetic compounds that can cause abnormalities in the functioning of the endocrine system of the human being, resulting in various health problems. Bisphenol‐A (BPA) is one of the important EDCs that is used in the manufacturing of plastics, food packaging canisters, and other day‐to‐day necessities. Since BPA is estrogenic in nature; its presence can affect the living component at a very low concentration. BPA and other EDCs are released from various sources like the plastic manufacturing industry, sewage treatment plants, and solid waste disposal points. Due to its global use, BPA has permeated different matrices, including our food sources. As a result, many adverse health effects have been reported, considering which, their treatment is necessary. Under the present investigation, we have reviewed various studies dealing with the sources, concentrations, and impact of BPA on the environment. In addition, we have also incorporated different treatment technologies including phytoremediation and bioremediation which can remove BPA effectively. Regardless of significant developments in our understanding of EDCs, uncertainties and knowledge gaps still occur and more studies are required to eradicate the problems of BPA contamination from our environment.

Planning a Sewage Treatment System for Smart Housing Societies: A Review

Smart housing societies are increasingly incorporating sustainable practices, including on-site sewage treatment. This paper reviews key considerations for planning a sewage treatment system in such communities. Factors like resident population, water usage patterns, and available space are analyzed. Different treatment technologies, including activated sludge, constructed wetlands, and membrane bioreactors, are evaluated for their suitability in smart housing contexts. The integration of smart monitoring and control systems for optimizing treatment processes and water reuse is discussed. Finally, the importance of adhering to local regulations and involving residents in the planning process is highlighted.

Faecal shedding of SARS-CoV-2 from patients with asymptomatic and mild COVID-19 without gastrointestinal symptoms in Ghana

ObjectiveIn this study, we sought to determine whether faecal shedding occurs among SARS-COV-2 positive Ghanaians, as reported elsewhere. Hence we assayed for SARS-COV-2 in the stools of 48 SARS-COV-2 confirmed patients at the Ho Municipal Hospital in Ghana.ResultsOf the 48 COVID-19 patients, 45 (93.8%) had positive tests for SARS-CoV-2 faecal shedding. About 60% reported no respiratory symptoms, while only 2% (1 patient) reported gastrointestinal (GI) symptoms in the form of nausea. Other symptoms reported included headache (57.9%), weakness (57.9%), cough (52.6%), blocked/runny nose (47.4%), fever (31.6%), sore throat (31.6%), and shortness of breath (21.1%). One person complained of nausea (5.3%) Semi-quantitative comparison of the SARS COV-2 viral loads in matched respiratory and faecal samples using the cycle threshold (CT) values revealed no statistical differences. Furthermore, the duration between collection of respiratory and faecal samples did not have any direct influence on the differences in the CT values. This suggests that treatment and use of sewage for environmental surveillance of SARS COV-2 could be a potential public health countermeasure.

Bibliometric Analysis of Nanostructured Anodes for Electro-Oxidative Wastewater Treatment

Last decade, a growing emphasis on developing sustainable and environmentally friendly technologies for electro-oxidative wastewater treatment has catalyzed innovation and spurred research efforts worldwide. Researchers may explore the use of renewable energy sources to drive electrochemical processes, as well as the development of eco-friendly electrode materials for wastewater treatments. The integration of nanostructured anodes into the electrolytic system for wastewater treatment has led to significant advancements in the removal of pollutants via electro-oxidation. Despite the great number of research articles related to the development and use of nanostructured anodes for electro-oxidative wastewater treatment, to our knowledge, no bibliometric analysis has been published in this domain. Therefore, this work presents a bibliometric study of publications on the designated theme, retrieved from the Web of Science Core Collection database, which were published over the last decade. The visual and network analysis of co-authorship among authors, organizations, countries, co-citation of authors, citation of documents and sources, as well as the co-occurrence of author keywords was performed using two compatible pieces of scientometric software, namely VOSviewer (version 1.6.18) and CiteSpace (version 6.2.R4). From 2013 to 2023, there has been a gradual increase in the number of publications regarding the development and use of nanostructured anodes for electro-oxidative wastewater treatment. It suggests a steady advancement in this field. The People’s Republic of China emerges as the most productive country, and it is a leader in international collaborations. Also, the United States of America, South Korea, and European Union countries have significant impacts on the research in this domain. The development and application of nanostructured materials for urea electro-oxidation is a main and prospective research theme. This bibliometric analysis allowed for the visualization of the present landscape and upcoming trends in this research field, thereby facilitating future collaborative research endeavors and knowledge exchange.

Assessing teratogenic risks of gadolinium in freshwater environments: Implications for environmental health

Gadolinium (Gd) is among the rare earth elements extensively utilized in both industrial and medical applications. The latter application appears to contribute to the rise in Gd levels in aquatic ecosystems, as it is excreted via urine from patients undergoing MRI scans and often not captured by wastewater treatment systems. The potential environmental and biological hazards posed by gadolinium exposure are still under investigation. This study aimed to assess the teratogenic risk posed by a gadolinium chelate on the freshwater cnidarian Hydra vulgaris. The experimental design evaluated the impact of pure Gadodiamide (25 μg/l, 50 μg/l, 100 μg/l, 500 μg/l) and its commercial counterpart compound (Omniscan®; 100 μg/l, 500 μg/l, 782.7 mg/l) at varying concentrations using the Teratogenic Risk Index (TRI). Here we showed a moderate risk (Class III of TRI) following exposure to both tested formulations at concentrations ≥ 100 μg/l. Given the potential for similar concentrations in aquatic environments, particularly near wastewater discharge points, a teratogenic risk assessment using the Hydra regeneration assay was conducted on environmental samples collected from three rivers (Tiber, Almone, and Sacco) in Central Italy. Additionally, chemical analysis of field samples was performed using ICP-MS. Analysis of freshwater samples revealed low Gd concentrations (≤ 0.1 μg/l), despite localized increases near domestic and/or industrial wastewater discharge sites. Although teratogenic risk in environmental samples ranged from high (Class IV of TRI) to negligible (Class I of TRI), the low Gd concentrations, particularly when compared to higher levels of other contaminants like arsenic and heavy metals, preclude establishing a direct cause-effect relationship between Gd and observed teratogenic risks in environmental samples. Nevertheless, the teratogenic risks observed in laboratory tests warrant further investigation.

Toward Selective Transport of Monovalent Metal Ions with High Permeability Based on Crown Ether-Encapsulated Metal-Organic Framework Sub-Nanochannels.

Achieving selective transport of monovalent metal ions with high precision and permeability analogues to biological protein ion channels has long been explored for fundamental research and various applications, such as ion sieving, mineral extraction, and energy harvesting and conversion. However, it still remains a significant challenge to construct artificial nanofluidic devices to realize the trade-off effects between selective ion transportation and high ion permeability. In this work, we report a bioinspired functional micropipet with in situ growth of crown ether-encapsulated metal-organic frameworks (MOFs) inside the tip and realize selective transport of monovalent metal ions. The functional ion-selective micropipet with sub-nanochannels was constructed by the interfacial growth method with the formation of composite MOFs consisting of ZIF-8 and 15-crown-5. The resulting micropipet device exhibited obvious monovalent ion selectivity and high flux of Li+ due to the synergistic effects of size sieving in subnanoconfined space and specific coordination of 15-crown-5 toward Na+. The selectivity of Li+/Na+, Li+/K+, Li+/Ca2+, and Li+/Mg2+ with 15-crown-5@ZIF-8-functionalized micropipet reached 3.9, 5.2, 105.8, and 122.4, respectively, which had an obvious enhancement compared to that with ZIF-8. Notably, the ion flux of Li+ can reach up to 93.8 ± 3.6 mol h-1·m-2 that is much higher than previously reported values. Furthermore, the functional micropipet with 15-crown-5@ZIF-8 sub-nanochannels exhibited stable Li+ selectivity under various conditions, such as different ion concentrations, pH values, and mixed ion solutions. This work not only provides new opportunities for the development of MOF-based nanofluidic devices for selective ion transport but also facilitates the promising practical applications in lithium extraction from salt-like brines, sewage treatment, and other related aspects.

A pilot-scale anoxic-anaerobic-anoxic-oxic combined with moving bed biofilm reactor system for advanced treatment of rural wastewater

Rural domestic poses a significant challenge to treatment technologies due to significant fluctuations in both water quality, particularly in terms of carbon concentration, and quantity. Conventional biological technology, such as anaerobic-anoxic-oxic (A2O) systems, is inefficient. In this work, a continuous pilot-scale anoxic-anaerobic-anoxic-oxic (A3O) reactor with a moving bed biofilm reactor (MBBR) system was constructed and optimized to improve the treatment efficiency of rural domestic wastewater. The sludge return ratio, volume ratio of the oxic-to-anoxic zone (Voxi/Vano), step-feeding and hydraulic retention time (HRT) at low temperature were considered the main parameters for optimization. Microbial analysis was performed on both the mixed liquor and carrier of the A3O-MBBR system under initial and post-optimized conditions. The results indicated that the A3O-MBBR improved the treatment efficiency of rural domestic wastewater, especially for total phosphorus (TP), which increased by 20 % compared with that of the A2O-MBR. In addition, the removal efficiencies of nitrogen and phosphorus were further optimized, and the average concentrations of total nitrogen (TN) and TP in the effluent reached 2.46 and 0.364 mg/L, respectively, at a sludge reflux ratio of 100 or 150 %, Voxi/Vano =200 %, step-feeding of 0.5Q/0.5Q (anaerobic/anoxic) and HRT of 15 h at low temperature in the A3O-MBBR, which met standard A of GB18918–2002, China (TN < 15 mg/L, TP < 0.5 mg/L). The average rate of attaining the standard increased by 58.63 % (post optimization). The microbial analysis showed an increase in species diversity and richness after the parameters were optimized. Moreover, compared to the microbial community structure before optimization, the post-optimization exhibited a more stable microbial structure with a significant enrichment of functional bacteria. Defluviimonas, Novosphingobium and Bifidobacterium, considered as the dominant nitrification or denitrifying bacteria, were enriched in the suspended sludge of the MBBR reactor, which the relative abundance increased by 3.11 %, 3.84 %, and 3.24 %, respectively. Further analysis of the microbial community in the carrier revealed that the abundance of Nitrospira and the denitrifying bacteria carried by the carrier were much greater than those in the suspended sludge. Consequently, the microorganism cooperation between suspended sludge and biofilm might be responsible for the improved performance of the optimized A3O-MBBR.

The Directions for Improving the Surface Wastewater Treatment Facilities

Prospective directions for increasing efficiency of the drains by improving the systems for collection, disposal and treatment of surface wastewater have been considered. The design and technological features of treatment facilities in operation have been analyzed. The significant shortcomings have been identified, as a result of which the quality of purified water discharged into water bodies, declared by manufacturers, is reduced and the operation is complicated. Promising directions for resolving the identified problems have been recommended: targeted formation of surface wastewater flows, increasing the engineering and technological level of mono-block structures, the use of modern structural materials, providing the possibility of remote monitoring and control of the technological process, as well as timely routine maintenance.

Development of microbial desalination cells for the treatment of reverse osmosis reject water: A new benchtop approach

To address the growing global demand for usable water, there is an immediate necessity to enhance wastewater treatment systems. A continuous mode adaption of the conventional three-chamber microbial desalination cell (MDC) configuration was used, with gravity facilitating the flow of residential reject water for desalination. Initially, operating in batch mode with a 100 mL treatment volume, the single microbial desalination machine was expanded to 300 mL in continuous mode, capable of treating 5 L of home refuse water over 36 days. The batch mode MDC had a maximum current and power density of 3.81 µA/cm2 and 0.337 µW/cm2, resulting in 76 % desalination and 83.9 % COD eradication rates. Scaling up increased the MDC's performance, reaching a maximum of 0.45 µW/cm2 and 5.31 µA/cm2, which was 1.3 times greater than batch mode operation. The current work demonstrates the feasibility of microbial desalination cells and their novel approach for treating much higher quantities of reverse osmosis (R.O.) saline water in a comparable period of roughly 36 days. It emphasizes the actual limits when dealing with real-world wastewater samples, presenting a unique path for biotechnology by simultaneously generating bio-electricity and tackling future contaminants. Furthermore, incorporating desalination chambers with microbial fuel cells increases efficiency and opens up new options for enhanced wastewater treatment, resource recovery, and bioenergy generation. This pioneering strategy uses innovative membrane technologies and microbial optimization approaches to push the limits of desalination.

An attempt to augment performance of machine learning models in a pilot-scale urban wastewater treatment system

The challenge we face is striking a balance between ensuring the standards for wastewater treatment processes and minimizing energy consumption. As such, accurate predictive models become critical. With machine learning algorithms having the ability to discern relationships between inputs and outputs, broad interest has been shown in their applications in wastewater treatment. A key research focus is on effectively adjusting these generic machine learning algorithms to adapt to frequent fluctuations of water quality, inflow volume, and environmental variations. This study developed a Nonlinear Autoregressive neural network (NARX) model having an adaptive real-time updating module to predict the ammonium concentration in the treated effluent. The model has exhibited high predictive accuracy on the testing data, achieving an R2 value of 0.997. By incorporating an adaptive real-time updating module, the model's capability to predict effluent ammonium concentration on novel data sets has been significantly improved, with the R2 value for these predictions increasing from an initial 0.918 to a more refined range of 0.966 to 0.984. Our findings confirm that integrating real-time updating capabilities with machine learning algorithms substantially improves the stability and predictive performance of the models. These outcomes will prompt a broader integration of artificial intelligence in the domain of environmental engineering, which shall foster the implementation of more accurate and eco-friendly wastewater treatment strategies.

To what extent are wastewater treatment systems a gateway for microplastic particles in the aquatic and terrestrial environments?

Sewage treatment plants are designed to handle wastes that include several types of pollutants, including microplastics (MPs), which are synthetic polymer materials fragmented to sizes &lt; 5 mm. Investigating the abundance and removal efficiency rates of MPs in wastewater treatment plants is important because the water body to which plant effluents are discharged may be adversely affected by the released MPs. Therefore, the abundance, characteristics, and removal of MPs at two sewage treatment plants located on the southwest coast of Norway are studied. Twenty-four samples were collected across two sampling sessions by using an ad hoc-designed plastic-free water sampling device, which was improved by applying a cascade of certified stainless-steel sieves. A combined sequence of enzymatic and strong oxidative incubations was performed for sample preparation. The obtained samples were chemically characterized and quantified using thermoanalytical techniques. The overall amounts of polymers in the inlet wastewater and outlet water were 366-616 μg/L and 34-57 μg/L, respectively, indicating an approximate MPs removal efficiency of 78%-85%. Polyethylene (≈ 36%-68%), polypropylene (≈ 7%-48%), polystyrene (≈ 5%-6%), polyvinyl chloride (≈ 15%-26%), polyamide (≈ 2%), polymethacrylate (≈ 3%-4%), polycarbonate (≈ 2%), and polyethylene terephthalate (≈ 9%-32%) were detected in the investigated samples. In biosolids, the overall quantity of MPs was 3.8-5.5 mg/g dry weight across the two investigated sewage treatment plants. Polyethylene (≈ 24%-44%), followed by polyvinyl chloride (PVC) (≈ 11%-16%), and polyamide (≈ 2%-22%) were the most commonly recurring polymer types. The outcomes of this study indicate that MPs are removed efficiently from wastewaters. However, large amounts of MPs accumulate in biosolids. Therefore, sludge dumping management procedures need to be improved to lower the amount of MPs released into the environment through effluents and biosolids.

Photo-Fenton-like degradation of tetracycline through peroxymonosulfate activation over 2D BiOBr/FeOOH nanosheets and membrane application

The selection of photosensitizer substrates with high photocatalytic efficiency is crucial for leveraging the advantages of metal-based materials in photo-Fenton-like process. Herein, we report a novel 2D layered BiOBr/FeOOH nanosheets equipped with a built-in electric field (BIEF) to activate peroxymonosulfate (PMS) for the degradation of tetracycline (TC). The photocatalytic efficiency of BiOBr is enhanced by fine-tuning the Br source quantity. Both experimental and theoretical analyses confirm that BIEF at the BiOBr/FeOOH heterointerface expedites the movement of photogenerated electrons, significantly boosting both photocatalytic and photo-Fenton-like activities. The BiOBr/FeOOH + PMS + Vis system exhibits a high TC removal rate of 96 % with only 0.24 mM of PMS and nearly 100 % of PMS utilization. Moreover, affixing BiOBr/FeOOH nanosheets onto a PVDF microfiltration membrane, we establish a continuous flow reactor system for antibiotic wastewater treatment. This system demonstrates a remarkable TC removal efficiency consistently above 97.5 % for 6 h of continuous injection, underscoring its practicality and potential for real-world applications.

Replenishment of landscape water with reclaimed water: threshold of hydraulic retention time employing transparency as a control indicator

ABSTRACT There exists a significant risk of water blooms during the utilization of recycled water in landscape environments. The nitrogen and phosphorus discharge standards of sewage treatment plants are very low. Controlling hydraulic retention time (HRT) is currently the most effective means to control water bloom. This article proposes a new method for determining the HRT threshold based on water transparency as a control indicator. The following results were obtained: (1) with the nitrogen and phosphorus concentrations of 15 and 0.5 mg/L, respectively, the threshold for HRT under high temperature and strong light is 4.6 days, while the threshold under low temperature and low light is 11.5 days. (2) With the nitrogen and phosphorus concentrations of 10 and 0.3 mg/L, respectively, the threshold for HRT under high temperature and strong light is 5 days, while the threshold under low temperature and low light conditions is 12.3 days. (3) The HRT threshold obtained under high temperature and strong light is lower than that obtained under low temperature and low light conditions. (4) The higher the concentrations of nitrogen and phosphorus, the smaller the HRT threshold obtained. (5) Blue algae have stronger adaptability than green algae and diatoms.

Fabrication of lignosulfonate-derived porous carbon via pH-tunable self-assembly strategy for efficient atrazine removal

Herein, a straightforward protocol was developed for the one-pot synthesis of N-doped lignosulfonate-derived carbons (NLDCs) with a tunable porous structure using natural amino acids-templated self-assembly strategy. Specifically, histidine was employed as a template reagent, leading to the preparation of 10-NLDC-21 with remarkable characteristics, including the large specific surface area (SBET = 1844.5 m2/g), pore volume (Vmes = 1.22 cm3/g) and efficient adsorption for atrazine (ATZ) removal. The adsorption behavior of ATZ by NLDCs followed the Langmuir and pseudo-second-order models, suggesting a monolayer chemisorption nature of ATZ adsorption with the maximum adsorption capacity reached up to 265.77 mg/g. Furthermore, NLDCs exhibited excellent environmental adaptability and recycling performance. The robust affinity could be attributed to multi-interactions including pore filling, electrostatic attraction, hydrogen bonding and π-π stacking between the adsorbents and ATZ molecules. This approach offers a practical method for exploring innovative bio-carbon materials for sewage treatment.