Surface Undulations Research Articles

Mathematical Models on Mechanics of Biofluids

In this work, we study the mathematical models of flows for some biofluids. In biomechanics, peristaltic flow plays an important role in which the motion generated in the fluid contained in a distensible tube when a progressive wave of area contraction and expansion travels along the wall of the tube. We consider the effect of elasticity of the tube wall in the flow through the progressive wave travelling along its length without its direct calculation. Since the no – slip condition has used on a moving undulating wall surface, it determines the sinusoidal boundary conditions on the upper and lower wall of the tube. The wide occurrence of peristaltic motion gives its result physiologically from neuro-muscular properties of any tubular smooth muscle.

Optimization of Electromagnetic-Wave Reflectivity Performance of Electromagnetic Shielding Yarn Prepared by Evaporation-Induced Sintering of Ga60.5In25Sn13Zn1.5 Alloy with Nanosilicates.

Electromagnetic interference (EMI) shielding textiles have received widespread attention, and liquid metal (LM) shows superiority in flexible and deformable electronics. Here, we introduce a novel method using nanosilicates to help sinter LM through capillary evaporation, resulting in strong adhesion to substrates. By adjustment of the amount of nanosilicates, flexible EMI shielding yarns are created using dip-coating and curing processes. The sintered LM tightly adhered to the undulating and uneven surfaces of polyurethane (PU) yarns. The as-fabricated ION/LM@PU ("ION" is abbreviation of "ionogel") has strong EMI shielding and low EM-wave reflection due to the high electrical conductivity of the LM layer and good impedance matching of P(AAm-co-AA) ionogel. The addition of an ionogel enhances EM-wave absorption and strengthens interfacial polarization, making it an effective green EMI shielding yarn for reducing secondary reflection pollution. ION/LM@PU exhibited high total electromagnetic interference shielding effectiveness (EMI SET) (∼56 dB), low reflected power coefficient (R) (∼0.153), high impedance matching (|Zin/Z0| ≈ 0.660), high tensile strength (∼23.75 MPa), and high elastic recovery (∼0.92 at 10th stretch-release cycle). The EMI shielding mechanism of ION/LM@PU ± 60° is composed of reflective loss and absorption loss (including multireflective loss, conduction loss, dipole polarization loss, and interfacial polarization loss).

Phase changes in burning precursor-laden single droplets leading to puffing and micro-explosion

When producing metal-oxide nanoparticles via flame spray pyrolysis, precursor-laden droplets are ignited and undergo thermally induced disintegration, called ‘puffing’ and ‘micro-explosion’. In a manner that is not fully understood, these processes are associated with the formation of dispersed phases inside the droplets. This work aims at visualizing the interior of precursor-laden burning single droplets via diffuse back illumination and microscopic high-speed imaging. Solutions containing iron(III) nitrate nonahydrate (INN) and tin(II) 2-ethylhexanoate (Sn-EH) were dispersed into single droplets of sub-100 μm diameter that were ignited by passing through a heated coil. At low precursor concentration, 50% of the INN-laden droplets indicate a gas bubble of about 5 μm diameter in the center of the droplet. The bubble persists for several hundred microseconds at a similar size. In almost all of these cases, the bubble expands at some point and the droplet ends up in a micro-explosion. In some of these instances, the droplet’s surface shows spatial brightness modulations, i.e., surface undulations, indicating the formation of a viscous shell. With increasing INN concentration, the fraction of droplets showing surface undulations, gas bubbles, and micro-explosions drastically decreases. This may be associated with a more rigid viscous shell and reduced mobility of bubbles. Bright incandescent streaks originating from the disrupting INN-laden droplets, may indicate sub-micrometer droplets or particles from within the droplets or formed in the gas phase. In contrast, Sn-EH-laden droplets show very fast disruptions, typically less than 10 μs from first visible deformation to ejection of secondary droplets. Bubbles and surface undulations were not observed.Graphical abstract

Axial compressive behaviour and design of concrete-filled wire arc additively manufactured steel tubes

The axial compressive behaviour of concrete-filled wire arc additively manufactured (WAAM) steel tubular columns is investigated experimentally in this paper. Firstly, the manufacture of a series of WAAM steel plates and tubes is described. The results of tensile testing performed on coupons cut from the WAAM plates, to obtain the mechanical properties of the printed material, are summarised. 3D laser scanning was employed to generate digital models and to capture the geometric features of the WAAM steel test specimens. Concrete was then cast into the WAAM steel tubes, creating a total of nine concrete-filled steel tubular (CFST) specimens of different diameters, thicknesses and lengths that were subjected to compressive loading. The axial compressive load-deformation responses and ultimate loads of the specimens were obtained and the influence of the as-built surface undulations of the WAAM sections was assessed. Comparisons of the test results against existing structural design provisions highlight the need to consider the influence of the weakening effect of the geometric undulations that are inherent to the WAAM process on the structural response of CFST sections, in order to achieve safe-sided strength predictions.

Inertial effects on free surface pumping with an undulating surface

Free surface flows driven by boundary undulations are observed in many biological phenomena, including the feeding and locomotion of water snails. To simulate the feeding strategy of apple snails, we develop a centimetric robotic undulator that drives a thin viscous film of liquid with the wave speed $V_w$ . Our experimental results demonstrate that the behaviour of the net fluid flux $Q$ strongly depends on the Reynolds number $Re$ . Specifically, in the limit of vanishing $Re$ , we observe that $Q$ varies non-monotonically with $V_w$ , which has been successfully rationalised by Pandey et al. (Nat. Commun., vol. 14, no. 1, 2023, p. 7735) with the lubrication model. By contrast, in the regime of finite inertia ( ${Re} \sim O(1)$ ), the fluid flux continues to increase with $V_w$ and completely deviates from the prediction of lubrication theory. To explain the inertia-enhanced pumping rate, we build a thin-film, two-dimensional model via the asymptotic expansion in which we linearise the effects of inertia. Our model results match the experimental data with no fitting parameters and also show the connection to the corresponding free surface shapes $h_2$ . Going beyond the experimental data, we derive analytical expressions of $Q$ and $h_2$ , which allow us to decouple the effects of inertia, gravity, viscosity and surface tension on free surface pumping over a wide range of parameter space.

Numerical Study on Heat Transfer Efficiency and Inter-Layer Stress of Microchannel Heat Sinks with Different Geometries

As electronics become more powerful and compact, laminated microchannel heat sinks (MCHSs) are essential for handling high heat flux. This study aims to optimize the MCHS design for improved heat dissipation and structural strength. An orthogonal experiment was established with the average surface temperature of the heat source as the evaluation metric, and the optimal structure was determined through simulation. Finally, cooling uniformity, fluidity, and performance evaluation criterion (PEC) analyses were carried out on the optimal structure. It was determined that the optimal combination was the triangular cavity microchannel (MCTC), with a microchannel width of 0.5 mm, a microchannel distribution density of 60%, and the presence of surface undulation on the microchannels. The result shows that the optimal structure’s peak inter-layer stress is just 34.8% of its longitudinal tensile strength. Compared to the traditional parallel straight microchannel (MCPS), this structure boasts an 8.6 K decrease in the average surface temperature and a temperature variation along specific paths that is only 9.9% of that in traditional designs. Moreover, the optimal design cuts the velocity loss at the microchannel entrance from 75% to 59%. Thus, this research successfully develops an effective optimization strategy for MCHSs.

Static Correction of Passive-Source Seismic Reflection Exploration on Undulating Surfaces

Elevation static correction is an important step in seismic data processing used to eliminate distortions in events caused by surface fluctuations. There is a well-established processing sequence for active-source seismic data, with static correction applied first, followed by subsequent processing. For passive-source data, static correction can be carried out using two methods. The first method is similar to the static correction of active-source seismic data and involves performing static correction on virtual shot gathers. The second method involves directly applying static correction to ambient noise and then using the corrected ambient noise to retrieve the virtual shot gathers. In this study, we derived and compared these two methods to perform static correction on passive-source data. We compared the above two methods through the forward modeling of passive-source data and field data from the Daqiao Gold Mine. The results showed that applying static correction to ambient noise and virtual shot gathers can correct passive-source data from an undulating surface to a flat surface. The equivalence of static correction on virtual shot gathers, and ambient noise offers more choices for conducting static correction of passive-source seismic reflection exploration on undulating surfaces.

Effect of thermal radiation and inclined magnetic field on thermosolutal mixed convection in a partially active wavy trapezoidal enclosure filled with hybrid nanofluid

This work focuses on the examination of the magneto-thermosolutal convection in a lid-driven wavy trapezoidal enclosure in the presence of thermal radiation. The wavy cavity is filled with radiative Fe3O4-Cu-H2O hybrid nanoliquid. In this work, two cases are considered depending on the location of heat and concentration sources. A portion of the vertical walls are kept hot and in high concentration while the remaining parts are in adiabatic condition. The adiabatic flat upper lid is moving towards the right with equal speed. In addition, the lower wavy border is cold and low concentration. The governing Navier–Stokes equations are modeled to describe thermosolutal phenomena within the wavy enclosure. These equations are solved by reconstructing a recently developed compact scheme. Computed outcomes are presented in terms of streamlines, isotherms, iso-concentrations, average Nusselt and Sherwood numbers to evoke the thermosolutal phenomena for various physical parameters. Also, computing in-house code is validated with the published numerical and experimental and literatures. This investigation surveys the roles of several well-defined parameters such as Richardson number (Ri), Lewis number (Le), Buoyancy ratio number (N), Radiation parameter (Rd), Hartmann number (Ha), inclination of angle (γ), undulation of the wavy surface (d) and solid volume fraction (ϕhnp) of the hybrid nanofluid. An increase in the Lewis number (Le) enhances species diffusion within the system but diminishes thermal transport. This work reveal that a change in ϕhnp from 0% to 4%, heat transfer is upgraded up to 4.28% in Case I and 3.93% in Case II while mass transfer is declined by 2.24% in Case I and 1.60% in Case II. Results indicate that Case I performed better than Case II in the case of energy and solutal transfer. This work has many practical applications such as heat exchangers, electronic device cooling, food processing and porous industrial processes.

Growth and performance of n++ GaN cap layer for HEMTs applications

Apart from providing high-quality ohmic contacts to III-N devices, n++ GaN cap layers can eliminate surface-related current collapse effects in high-electron-mobility transistors (HEMTs). Various metal-organic chemical vapor deposition conditions and n-type doping are tested in GaN growth on sapphire by using triethylgallium as a Ga precursor, replacing more conventional trimethylgallium. Consequently, despite relatively low temperature of the growth at 800 °C to facilitate InAlN barrier capping, optimized growth conditions and SiH4 flow provided free electron concentration of 7.2 × 1019 cm−3 and mobility of 103 cm2/Vs. Moreover, electron concentration in the range of 1020 cm−3 is demonstrated by using flow modulation epitaxy. On the other hand, as calibration growths indicated, excessive SiH4 flow alone can lead to high density of edge dislocations and surface undulations without enhancing free electron concentration. 6 nm (Si: 4.2 × 1019 cm−3) and 8 nm thick (Si: 7.2 × 1019 cm−3) n++ GaN cap is implemented in normally-off n++ GaN/InAlN/AlN/GaN HEMTs grown on Si, with a collapse-free performance for the latter case. By calculating energy band and free carrier concentration profiles of the heterostructures it is shown, that free electrons of a sufficiently thick and doped n++ GaN cap can shield the channel from the unstable surface potential.

Regulating mechanisms of external axial magnetic field on flow and heat transfer behavior for process optimization in plasma beam polishing

Plasma beam polishing has emerged as an innovative alternative to conventional metal finishing techniques. However, the precision machining ability of plasma arc encounters challenges due to the formation of surface undulations, while previous research has predominantly focused on parameter adjustments. In this paper, the feasibility of optimizing the plasma beam polishing process was validated through magnetic field regulation, as the surface topography and subsurface structure were obviously flattened. Given this, a micro plasma arc model under inhomogeneous axial magnetic field was established to explore the regulating mechanisms of the external axial magnetic field on the flow and heat transfer behavior of the plasma arc. Through this model, the plasma characteristics (magnetic induction intensity, electric potential, arc current, Lorentz force, plasma velocity and electron temperature) were comprehensively discussed. The results indicate that the external shape of the plasma arc is determined by the self-induced magnetic field, while the externally applied axial magnetic field significantly influences the internal flow of the plasma arc. The axial and radial magnetic fields generated by the excitation coil can induce circumferential rotation by dragging the plasma arc with Lorentz force, creating a more suitable energy beam for the polishing process. To verify the model, the arc temperature was measured using spectroscopic diagnostics, and the arc shape was captured using a high-speed camera, both of which were basically consistent with the simulation results.

The influence of nitrogen content on the microstructure and properties of W-Ta-Cr-V-N refractory high-entropy nitrides

To enhance the mechanical performance and corrosion resistance of refractory high-entropy alloys (RHEAs) and to identify materials better suited for severe high-temperature and corrosive environments, this study utilized a double glow plasma surface alloying technique to fabricate a W-Ta-Cr-V-N refractory high-entropy nitride coating on a W substrate. The microstructure and phase structure of the samples were characterized using a scanning electron microscope and X-ray diffractometer. The mechanical properties of the samples were evaluated through microhardness testing, while their corrosion performance was assessed by potentiodynamic polarization and electrochemical impedance spectroscopy measurements. The study investigated the effects of different nitrogen contents on the microstructure, mechanical properties, and corrosion resistance of the BCC-structured W-Ta-Cr-V alloy in the past tense. The study found that the doping of an appropriate amount of nitrogen can lead to the formation of FCC and HCP structured nitrides. As the nitrogen content increases, there is a significant change in the preferred orientation of the coating. When the nitrogen content is 16.6 at.%, the distribution of the nitrides is uneven, resulting in increased surface undulations and roughness. Conversely, when the nitrogen content is elevated to 48.1 at.%, the clustering of surface nitride particles becomes more pronounced, leading to a decrease in the coating density. The thickness of the nitride coatings is around 10 μm, with a slight decrease in thickness as the nitrogen content increases. The hardness of the coatings is significantly superior to that of the W-Ta-Cr-V alloy films, reaching up to 3465 HV0.25 in the highest instance. The introduction of 31.4 at.% nitrogen results in the densest coating, effectively enhancing the corrosion resistance of the refractory high-entropy alloy. Therefore, the doping of an appropriate amount of nitrogen can alter the microstructure of the refractory high-entropy alloy, improve its mechanical properties, and enhance its chemical stability.

Biomimetic Hydrodynamic Sensor with Whisker Array Architecture and Multidirectional Perception Ability.

The rapid development of ocean exploration and underwater robot technology has put forward new requirements for underwater sensing methods, which can be used for hydrodynamic characteristics perception, underwater target tracking, and even underwater cluster communication. Here, inspired by the specialized undulated surface structure of the seal whisker and its ability to suppress vortex-induced vibration, a multidirectional hydrodynamic sensor based on biomimetic whisker array structure and magnetic 3D self-decoupling theory is introduced. The magnetic-based sensing method enables wireless connectivity between the magnetic functional structures and electronics, simplifying device design and endowing complete watertightness. The 3D self-decoupling capability enables the sensor, like a seal or other organisms, to perceive arbitrary whisker motions caused by the action of water flow without complex calibration and additional sensing units. The whisker sensor is capable of detecting a variety of hydrodynamic information, including the velocity (RMSE<0.061ms-1) and direction of the steady flow field, the frequency (error<0.05Hz) of the dynamic vortex wake, and the orientation (error<7°) of the vortex wake source, demonstrating its extensive potential for underwater environmental perception and communication, especially in deep sea conditions.

Advanced SiGe:B Raised Sources and Drains for p-type FD-SOI MOSFETs

We have evaluated the feasability of selectively growing, with a chlorinated chemistry, 20 to 30 nm thick SiGe:B Raised Sources and Drains with Ge concentration gradients (from 50% down to 20%-30%, typically) on each side of FD-SOI transistors. The motivation was twofold: (i) inject meaningful amounts of compressive strain in the channel of p-type MOS devices thanks to high Ge concentrations in layers sitting in the same plane than Si or SiGe channels and (ii) benefit from lower Ge concentration SiGe layers on top that are easier to germano-silicide. Growing a thin Si(:B) cap on SiGe:B otherwise yields more uniform and stable contacts. We have thus studied the Si capping of SiGe 20% or 30% layers. As growth has to be conducted, for Si, at temperatures significantly higher than that of SiGe (750°C, to be compared with 700°C for SiGe 20% and 650°C for SiGe 30%, typically), we have quantified the impact of using temperature ramping-ups with SiH2Cl2 + HCl flowing into the growing chamber. The purpose of such active ramps was to prevent elastic strain relaxation, e.g. the formation of SiGe surface undulations that would happen with temperature ramps under H2 only.

Effects of steepness on turbulent heat transfer over sinusoidal rough surfaces

We conducted a direct numerical simulation (DNS) study to investigate the impact of surface undulation steepness on rough wall turbulent heat transfer. The flow geometry was turbulent open-channel flow over three-dimensional sinusoidal rough surfaces. To examine the effects of steepness, we systematically varied the streamwise and spanwise wavelengths of the sinusoidal roughness while keeping the roughness height constant. The friction Reynolds number ranged from 180 to 600, and we considered a passive scalar with the fluid Prandtl number was 0.7, assuming air flow conditions. In the fully rough regime, the velocity roughness function is expressed as a function of the inner-scaled equivalent sand grain roughness ks+ independent of steepness, whereas the steeper surfaces with shorter wavelengths result in larger temperature roughness functions at the same ks+ value. Analysis of the physical mechanisms that increases the roughness function shows that the pressure drag primarily contributes to the increase in the velocity roughness function, while the temperature roughness function is mainly augmented by the roughness-induced wall heat transfer term, correlating with the steepness of the surface undulations. It is also suggested that the effective slope, which quantifies the steepness of rough surfaces, could improve the predictive accuracy of existing correlations for the temperature roughness function.

Tribo-Dynamic-Wear coupling analysis for Water-lubricated Bearings with journal surface imperfection under repeated start-stop cycles

Water-lubricated Bearings (WLBs) are the core transmission components of a ship propulsion system, and their wear behavior primarily occurs during the starting and stopping states. To characterize the wear behavior of WLBs, an equivalent experiment is conducted on bush material to obtain the relationship between dimensionless wear coefficient and sliding distance based on the Archard wear model. Then, an experimentally determined transient wear model is incorporated into a tribo-dynamic model to develop a fully coupled Tribo-Dynamic-Wear (TDW) model for the WLBs during repeated start-stop cycles. In this model, the 3D thermal effect, the transient bush worn surface and the geometric imperfection of the journal surface are considered. Numerical results show that the wear rate is more significant at the beginning of the start-up state and the end of the stopping state of the WLB. Meanwhile, it is found that compared to a perfect journal, a reasonable undulation number and undulated amplitude of the journal surface can improve the wear resistance performance of WLBs during repeated start-stop cycles. More specifically, a relatively lower undulation number leads to a smaller wear volume than the perfect journal, and the undulated journal surface has an optimal undulated amplitude that minimizes the wear volume.

Transport enhancement in the laminar rotating disk boundary layer

Enhanced momentum and heat transport in a three-dimensional rotating disk boundary layer due to the consideration of a wavy disk surface is an already known fact in the literature. Such a transport enhancement is primarily associated with two fundamental attributes of the wavy disk: the increased surface area and the enhanced convection due to the surface undulations. However, there exists no further information about their individual role, mutual interaction, and individual share in enhancing the convective transport in the rotating disk boundary layer. This study aims to investigate these facts in detail by considering radially heterogeneous different wavy configurations on the disk surface. It is revealed that the said attributes contribute non-trivially to enhance the transport phenomena. Their impactful role is identified due to the strengths of circumferential and crossflow velocity components, the magnitude of flow swirl angle, and hence due to the coefficients of skin friction and their inter relationship. In this regard, a fundamental benchmark regarding the relative strength of the two coefficients of skin friction is identified from the flat disk case. Decisive observations regarding the impact of surface undulations and the increased surface area of the wavy disk on the enhanced convective transport are made with the aid of this benchmark. It is observed that the enhanced transport phenomena, especially the heat transfer, mainly depend upon the further dominance of the circumferential velocity component. In the situations of increased dominance of rotational flow Kw&amp;gt;Kf, the increased convection and surface area collectively contribute to enhance the thermal transport while in a reverse situation Kw&amp;lt;Kf the convection contributes adversely by even reducing the impact of the increased surface area. In the neutral situation where the dominance of rotational velocity is neither increased nor decreased (i.e., Kw≈Kf), any increase in the transport phenomena is wholly due to the increased surface area. Therefore, the presence of surface undulations or increase in surface area is not the only criterion for an optimum rise in the transport phenomena, rather the impact of surface undulations on the velocity profiles is important which is manipulated due to their positioning on the disk surface. It is observed that the presence of surface undulations in the central and intermediate regions on the disk surface causes to increase the gradients of the crossflow velocity while their presence in the near rim location causes to enhance the gradients of the circumferential velocity. Thus, the configurations that have higher undulations in the near rim region outperform the other configurations.

First Approach in Analysis of Tool Wear When Milling Additive Manufacturing (AM) Parts

Wire arc additive manufacturing (WAAM) and laser-based powder bed fusion (L-PBF) are additive manufacturing (AM) processes that allow the manufacturing of complex part geometries. The manufacturing of AM parts does not result in high-quality functional surfaces; therefore, postprocessing such as milling is usually required. For L-PBF parts, the support structures and, for WAAM parts, the undulating surface are usually removed after AM processes. These two application-related cases are investigated in this work, with the conclusion that support structure milling and the milling of the surface of WAAM parts lead to the dimensionally increased wear of milling tools in comparison to milling of solid material.

Impact of inclined magnetic field on natural convection in ferrofluid within a semi-circular enclosure with a heated wavy surface

Ferrofluids are liquids that exhibit distinctive magnetic properties when subjected to a magnetic field. Due to their magnetic susceptibility, ferrofluids have recently gained considerable scientific attention. They find tools in different fields, such as electronics, mechanical engineering, and materials science. The inclusion of the semi-circular enclosure inscribed around a heated wavy cylinder provides innovative perspectives essential for engineering applications involving induction furnaces and cancer therapy devices. This paper aims to conduct a computational investigation into the influence of an inclined magnetic field on the free convection within a semi-circular cage stuffed with a ferrofluid featuring an internally undulating surface. It is considered that the interior wavy cylinder was warmed ( T h ) , and the outer semi-circular enclosure is cold ( T c ) . The analyzed system’s governing equations are computed using the Galerkin finite element method (GFEM). The ferrofluid’s flow pattern and thermal transport rate are investigated about relevant non-dimensional values, such as the wave numbers, the number of Hartmann ( 0 ≤ Ha ≤ 20 ) , the number of Rayleigh ( 10 3 ≤ Ra ≤ 10 6 ) , and the volume fraction ( 0.00 ≤ ϕ ≤ 0.09 ) . Evaluating the results involves examining isotherms, analyzing the distribution of flow velocities, and calculating the Nu avg , all while considering variations in fundamental physical parameters. As the Hartmann number ( Ha ) decreases and both the number of Rayleigh ( Ra ) and volume fraction ( ϕ ) rises, the Nu avg of the ferrofluid exhibits an increased. As a result of incorporating ferroparticles, the simulation identifies a maximum value of 35.86 for the Nu avg . It is worth noting that an enhance in Hartmann numbers is associated with an 80% decrease in the velocity stream function. On the other hand, an escalation in ferroparticle values leads to a 9.7% reduction, while elevated Rayleigh numbers result in a 60.8% surge in the stream function. Moreover, the irreversibility stemming from fluid friction, transfer of heat, and the magnetic field can be minimized for ferrofluid fluids ( n = 1 ), by employing the optimal parametric combination.

The relationship between atmospheric particulate matter, leaf surface microstructure, and the phyllosphere microbial diversity of Ulmus L.

BackgroundPlants can retain atmospheric particulate matter (PM) through their unique foliar microstructures, which has a profound impact on the phyllosphere microbial communities. Yet, the underlying mechanisms linking atmospheric particulate matter (PM) retention by foliar microstructures to variations in the phyllosphere microbial communities remain a mystery. In this study, we conducted a field experiment with ten Ulmus lines. A series of analytical techniques, including scanning electron microscopy, atomic force microscopy, and high-throughput amplicon sequencing, were applied to examine the relationship between foliar surface microstructures, PM retention, and phyllosphere microbial diversity of Ulmus L.ResultsWe characterized the leaf microstructures across the ten Ulmus lines. Chun exhibited a highly undulated abaxial surface and dense stomatal distribution. Langya and Xingshan possessed dense abaxial trichomes, while Lieye, Zuiweng, and Daguo had sparsely distributed, short abaxial trichomes. Duomai, Qingyun, and Lang were characterized by sparse stomata and flat abaxial surfaces, whereas Jinye had sparsely distributed but extensive stomata. The mean leaf retention values for total suspended particulate (TSP), PM2.5, PM2.5-10, PM10-100, and PM> 100 were 135.76, 6.60, 20.10, 90.98, and 13.08 µg·cm− 2, respectively. Trichomes substantially contributed to PM2.5 retention, while larger undulations enhanced PM2.5-10 retention, as evidenced by positive correlations between PM2.5 and abaxial trichome density and between PM2.5-10 and the adaxial raw microroughness values. Phyllosphere microbial diversity patterns varied among lines, with bacteria dominated by Sediminibacterium and fungi by Mycosphaerella, Alternaria, and Cladosporium. Redundancy analysis confirmed that dense leaf trichomes facilitated the capture of PM2.5-associated fungi, while bacteria were less impacted by PM and struggled to adhere to leaf microstructures. Long and dense trichomes provided ideal microhabitats for retaining PM-borne microbes, as evidenced by positive feedback loops between PM2.5, trichome characteristics, and the relative abundances of microorganisms like Trichoderma and Aspergillus.ConclusionsBased on our findings, a three-factor network profile was constructed, which provides a foundation for further exploration into how different plants retain PM through foliar microstructures, thereby impacting phyllosphere microbial communities.

Experimental study of wire arc additively manufactured steel sections stiffened by sinusoidal waves

Numerical models and initial tests conducted on specimens produced using selective laser melting have indicated that structural sections may be stiffened by imposing sinusoidal waveforms on their geometries which delay buckling and improve the overall buckling resistance. Wire arc additive manufacturing (WAAM) stands out as the most promising additive manufacturing technique for fabricating sections of the scale required in the construction industry, however, there is currently a lack of understanding of how the undulating surface finish inherent to WAAM will affect the stiffening effect of the sinusoidal waveforms. Therefore, this paper details an experimental study involving ten WAAM equal angle sections stiffened with two different sinusoidal wave patterns identified as the optimal patterns in previous numerical analysis. The production, geometric measurement and testing of the sections are described and the material properties of the WAAM material are determined. All equal angle section specimens tested fall within Eurocode 3 Class 4 and the stiffening wave patterns are shown to benefit the slenderer sections more. Comparative analysis between the material consumption and relative strength is provided, highlighting the potential for sinusoidal WAAM sections to improve the material efficiency and facilitate economic design practices within the steel construction industry.