Surface Of Tube Research Articles

Coaxial electrospinning synthesis free-standing Sn/TiO2 flexible carbon fibers with sheath/core structure for advanced flexible lithium/potassium-ion batteries

Flexible Sn/TiO2 carbon nanofiber (ST-NCF) composites were constructed by doping TiO2 into tin-based carbon nanofibers via coaxial electrospinning. Sn/TiO2 carbon nanofiber was directly used as an anode for Lithium-ion Batteries (LIBs) and Potassium-ion Batteries (PIBs), which show exceptional electrochemical performances. The layered sheath/core structure of the material lead to its good electrochemical properties, where the core Sn carbon nanofiber was encapsulated by the sheath layer of TiO2 nanoparticles. In addition to enhancing its electrical conductivity, the outer TiO2 and N-doped carbon fiber matrix also provide a buffer zone for volumetric strain during charging and discharging. The fiber core Sn and sheath TiO2 form a heterojunction interface on the two-dimensional tube surface, which increases the diffusion rate of ions and electrons. After 100 cycles, TiO2-NCF and ST-NCF-40%TBT (40% TBT indicates the percentage of TiO2 in shell solution to the total composition of shell spinning solution) show capacities of 386.6 mAh g−1 and 1336 mAh g-1, respectively, at 0.5A g-1. After 2000 cycles, ST-NCF-40%TBT in LIBs displayed a high capacity of 299 mAh g-1 at 10 A g-1. After 350 cycles at 1A g-1, the capacity of ST-NCF-40%TBT in PIBs is reserved at 307 mA h g-1. Due to the superior mechanical flexibility of ST-NCF-40%TBT films, it will be a promising anode candidate for flexible LIBs and PIBs.

Oxygen corrosion of reboiler tube served in production of dilution steam from heat exchanger of petrochemical refinery

This paper reports the oxygen corrosion of heat exchanger tubes serviced in dilute steam generation system. The floating head heat exchanger employed in a petrochemical industry underwent remnant corrosion failures particularly at lower passes of tube bundle. Initially remote field eddy current inspection technique was employed for tube bundle conditional assessment and further, root cause of degradation of tube had been analyzed. Comprehensive experimental techniques including visual examination, tube chemistry analysis, external tube surface morphological analysis, elemental mapping, scanning electron microscopy, light microscopy and x-ray diffraction studies were employed. The tube surface at the degraded position with its cross sectional examination was rigorously evaluated as well. Moreover, actual steam parameters such as pH, conductivity and iron & chloride concentration have been monitored in the petrochemical facility. The detailed analysis concluded that dissolved oxygen in boiler feed water (BFW) was the root cause for corrosion failure. Several other foreign elements were detected and source of each element was discussed in the context of actual heat exchanger operating conditions. Simulated conditions of BFW service have electrochemically been evaluated in two different dissolved oxygen concentrations at 7.5 ppm and 12.7 ppm, respectively. Even small increase of dissolved oxygen in BFW could lead to promotion of oxygen reduction reaction. Theoretically SA179 tubes operated at pH of 9.75 could lead to formation of bicarbonate and it could protect the tube in absence of dissolved oxygen as evaluated by Molecular Dynamics simulation. However, according to obtained results, tube has been degraded due to presence of dissolved oxygen in BFW. Various contributing factors such as external paint/coat removal, absence of de-aerator system in BFW treatment and improper corrosion inhibitor programme were discussed. Several practical countermeasures have been suggested to mitigate oxygen corrosion failure in petrochemical refineries.

Justification of the Locations of Differential Pressure Sensors for Coarse and Fine Filter Elements Installed one Inside the Other in a Single Gas Filter Housing

Statement of the problem. The relevant task of ensuring the uninterrupted operation of modern gas pressure reduction systems is to develop and comprehensively substantiate the possibility of using two-stage filters for natural gas purification in gas reduction points and theoretically substantiate the method for calculating the pressure drop in cylindrical filter elements (CFE). Results. It is proved that when gas flows in the upper cross section of the filter, the pressure drop will be less than in lower cross sections, including the pressure drop in the lowest cross section. This leads to a larger amount of leaking gas, to a larger mass of impurities settling in the lower part of the filter elements of cylindrical coarse and fine cleaning and to a greater degree of their clogging. Therefore, it is recommended to place gas pressure sensors in the lower part of the internal volume of the coarse and fine-cleaned CFE, so that the flow direction of the coarse and finely purified gas washing the sensors at the location of the hole for measuring statistical pressure is tangential to the side surface of the sensor tube. Then the flow direction of the roughly and finely purified gas entering the holes of the sensors is carried out at an angle of 90° and the pressure gauges measure the static pressure. Conclusions. The locations of pressure drop sensors on coarse and fine filter elements installed one inside the other in a single gas filter housing are substantiated. The proposed arrangement of differential pressure sensors will significantly increase the possibility of receiving an earlier signal about the degree of clogging of the gas filter at the control room, as well as have a significant amount of time for timely removal of blockages formed in the coarse cleaning CFE and replacement of fine cleaning CFE.

Ru-doping W4.6N4 nanoparticles anchored on N-doped graphene tubes as efficient hydrogen evolution electrocatalyst

Designing efficient electrocatalysts for hydrogen evolution reaction (HER) is essential to facilitate hydrogen energy applications. Herein, efficient strategies of doping with metal atoms (Ru) and incorporating with conductive carbon-based material (N-doping graphene tubes) have been developed to construct the hybrid electrocatalyst RuW4.6N4@N-GTs, in which, Ru-doped W4.6N4 nanoparticles integrated on the surface of N-doped graphene tubes. RuW4.6N4@N-GTs reveals superior HER activity and good stability, with a low overpotential of 29 mV to deliver the current density of 10 mA cm−2 and a low Tafel slope of 57 mV dec−1. The unique 3D nano-structure morphology of abundant homogeneous RuW4.6N4 nanoparticles supported on conductive N-GTs network carrier contributes to expose more electrochemical active sites, promoting electrolyte transport and gas emission. At the same time, the N-GTs skeleton could prevent the RuW4.6N4 particles from agglomerating and collapsing, thus leading to the superior stability during HER process. The in situ Ru heteroatom doping could cause the directional electron transfer and more nitrogen vacancies, thus modulating the electron structure of catalysts and optimizing the hydrogen adsorption free energy. The synergistic effect of the above merits endows RuW4.6N4@N-GTs with outstanding HER performance for potential applications in the hydrogen production field.

Possibility assessment for using protective coatings and polymer materials on tubing to prevent inorganic scaling on the inner surface of pipes

AbstractThe inorganic scaling in wells is a common problem faced by mining companies. At present, the use of protective coatings for tubing as a measure to prevent or reduce the formation of inorganic scale deposits on pipe walls has not been fully studied. To use protective coatings as a measure to counteract the deposition of inorganic salts, it is necessary to develop a method that allows assessing the ability of coatings, as well as polymer and metal materials, to prevent the formation of inorganic scale deposits on the inner surface of pipes.The article proposes a method for assessing the ability of protective coatings to resist the inorganic scaling on the inner surface of tubing. The proposed assessment method allows to make an informed decision on the advisability of using internal protective coatings of tubing to prevent (or reduce) the formation of inorganic scale deposits. The authors consider design features of a test bench for assessing the resistance of coatings to inorganic scale deposits, which allows to simulate the conditions for the formation of scale deposits that are as close as possible to the real conditions of oil production facilities. The article presents the results of bench tests of nine coating samples, two polymer samples and one sample made of St 40G2 steel. To assess the effectiveness of using tubing with an internal anti-corrosion coating as a measure to combat scale deposits, additional research is required to assess the possibility of complex use of coatings in conjunction with other methods of preventing processes of inorganic scaling. Thus, the authors developed the Bench for assessing the resistance of protective coatings of tubing to inorganic scale deposits. A dynamic testing technique is proposed to evaluate the resistance of protective coatings to inorganic scale deposits. Based on the presented results, conclusions were drawn about the possibility of using protective coatings on tubing as a measure to prevent the formation of inorganic scale deposits on the inner surface of the tubing.

Numerical simulation of dynamics behavior of pulsed-DC helium plasma jet confined by parallel magnetic field at atmospheric pressure

A two-dimensional axisymmetric fluid model is used to simulate the dynamics behavior of an atmospheric-pressure helium plasma jet in the presence of a parallel magnetic field. The plasma jet is generated in a coaxial dielectric barrier discharge (DBD) driven by pulsed direct-current voltage. Comparative analysis of the plasma jet with and without the parallel magnetic field indicates that a slightly thinner plasma sheath inside the tube is present with the parallel magnetic field as a result of the decreased accumulated electrons on the inner surface of dielectric tube. After the streamer propagates outside the tube, a little more concentrated electron distribution in the annular wall is observed by applying the magnetic field because of the reduced electron diffusion in the radial direction and the confinement effect of the magnetic field on the electrons in the avalanche heads. The tiny reduction in the length of plasma jet is attributed to the E × B drift of charged particles. These results demonstrate that the parallel magnetic field has no apparent effect on the propagation of the plasma jet, and it contributes little to the performance improvement of the coaxial DBD, which agrees well with the previous experimental observations. This little impact of the parallel magnetic field on the coaxial DBD plasma jet may result from negligible contribution of the memory effect to the sole discharge pulse as well as the weak confinement effect of the applied magnetic field on the surface electrons that moves along the magnetic field lines under electrostatic repulsion. Published by the American Physical Society 2024

Numerical analysis of the heat transfer performance of the absorber tube of a parabolic trough solar collector using the swirling flow technique

In the present work, the absorber tube of the DISS (Direct solar steam) solar plant in Plataforma Solar de Almeria (Spain) is powered by fluid flows in a swirl motion. Numerical simulations are used to predict the performance of a parabolic trough solar collector with inlets that allow the working fluid to flow in a swirl motion inside the absorber tube. There are numerous sites for tangential inlets distributed along the absorber tube. There is one inlet placed up, one located down, two located up, and two located down. High Reynolds numbers between 2.2 × 105 and 6.2 × 105 are used for the simulation. When the collector with the tangential inlet is compared to a conventional collector, the results reveal that using one inlet down causes a 9.1K decrease in the average temperature of the lower surface of the absorber tube. Compared to axial flow, one inlet down increases useful heat and heat transfer by 12.7 % and 41.7 %, respectively. The average friction factor of axial flow is 16.4 % higher than that of one inlet down. The collector with a tangential inlet reduces surface area by 10.9 % over Reynolds ranges when compared to an axial flow collector. Therefore, the thermal strain on the absorber tube and collector surface area is reduced by the swirling flow in the parabolic trough solar collector. As a helpful design tool, thermal performance correlations of absorber tubes with tangential inlets are constructed.

Elastoplastic Mechanical Properties and Kinematic Hardening Model of 35CrNi3MoVR.

The existing tensile-compression elastoplastic models are not suitable for varies of materials. An accurate constitutive model of the elastoplastic mechanical properties more suitable for 35CrNi3MoVR was produced by optimizing the existing fitting equations based on uniaxial tensile-compression tests, which are able to describe the elastoplastic stress-strain relation and Bauschinger effect varying with the maximum tensile plastic strain. A UMAT subroutine of the constitutive model in ABAQUS was proposed and conducted for FEM calculation. Hydraulic autofrettage tests were carried out under different pressures on thick-walled 35CrNi3MoVR tubes, and the results were compared with those of FEM calculations to further validate the accuracy of the fitting model. The results show that the constructed power function kinematic hardening model can effectively describe the elastoplastic mechanical properties of 35CrNi3MoVR and can be applied to the autofrettage calculation of this material. The comparison among the calculation results of different models proved that the model proposed in this research has better performance compared to other existing models. Taking the Mises stress at the inner surface of the thick-walled tubes as the evaluation criterion, the error of the power function kinematic hardening model reaches less than 3%, decreasing the error by at least 50%.

Simulation study on the effect of liquid ammonia spray on the heat transfer performance of multiple heat exchange tubes

Abstract In this paper, aiming at the problems of low heat transfer efficiency and uneven heat transfer of heat exchange tubes in refrigeration and air conditioning chillers, a liquid ammonia spray cooling method is proposed, and a flow and heat transfer model is established. The distribution of refrigerant droplets in the fluid domain and the heat transfer on the surface of the heat exchange tube are simulated under different spray speeds, spray directions, and double nozzle sprays. The results show that with the increase of spray velocity, the heat transfer performance of heat exchange tubes decreases first and then increases. The effect of spray velocity on the heat transfer performance of each row of heat exchange tubes is not consistent. The farther away it is from the nozzle, the greater the speed corresponding to the peak value of the heat transfer performance improvement of the heat exchange tube will be; the spray direction (gravity) has little influence on the heat transfer performance of the heat exchange tube, which is within 5.1%. Compared with single-nozzle spray, double-nozzle spray greatly improves the heat transfer performance of multi-row heat exchange tubes.

MFANet: Multifeature Aggregation Network for Cross-Granularity Few-Shot Seamless Steel Tubes Surface Defect Segmentation

MFANet: Multifeature Aggregation Network for Cross-Granularity Few-Shot Seamless Steel Tubes Surface Defect Segmentation

Experimental study on the scaling law of the heat exchange tube surface in the process of low-temperature single-effect distillation of high-mineralized mine water

High-mineralized mine water, due to its characteristics such as high mineralization degree, will have scaling phenomena on the surface of the heat exchange tube during the desalination treatment process, resulting in a reduction in the water production efficiency of the equipment and affecting the normal operation. To reduce the cost of water production and improve the service life of distillation equipment, this paper independently designs and builds a low-temperature single-effect distillation high-mineralized mine water experimental system to study the influence of operating parameters (temperature, spray density, concentration ratio, and system pressure) on the scaling law on the surface of the heat exchange tube. The distribution and characteristics of scale deposits on the surface of the heat exchange tube are analyzed through the growth rate and microscopic morphology of the scale deposit. The results indicate that the scaling on the surface of the titanium plate is mainly in the needle-like and rod-like morphology of CaCO3 aragonite, and a small amount of CaSO4 and calcite are generated with the increase of temperature. It was found that within the range of spray density from 0.0509 kg/(m·s) to 0.0625 kg/(m·s), concentration ratio from 2.3 to 2.7, and system pressure at 36.3 kPa, it is beneficial to the evaporation heat transfer of the heat exchange tube and the reduction of scaling generation. At the same time, it is found that the scaling of the first row of heat exchange tubes is mainly within the range of circumferential angle from 0 to 100 degrees, and the scaling of the second row and the third row of heat exchange tubes is mainly within the range of circumferential angle from 110 to 170 degrees. The research results of this paper provide support for the design and operation of the low-temperature multi-effect treatment system for mine water in engineering, promote the process of zero discharge of high-mineralized mine water in Xinjiang, China, and improve the resource utilization rate of high-mineralized mine water.

Comparative energy, exergy and entropy generation study of a minichannel and a conventional solar flat plat collectors

Considering the importance of using renewable energies for human societies, it is necessary to optimize the devices used. Flat plate solar collectors play a prominent role in the domestic and industrial sectors, so it is very important to enhance their performance. Changing the structure of the collector and using minichannel flat plate collectors (MFPCs) instead of sheet and tubes conventional flat plate collectors (CFPCs) is one choice. This study examines and compares the performances of a MFPC and a CFPC based on the energy, exergy and entropy generation perspectives. The working fluid is water and the fluid flow is laminar. Both collectors have the same contact surface between the working fluid and the inner surface of the riser tubes or the minichannels. In order to solve the equations, a thermal model is developed and the engineering equation solver is used. The results show that for all of the investigated conditions, the thermal and exergy efficiencies of the MFPC are higher than those of the CFPC and the maximum energy and exergy superiorities of the MFPC are 13.8 and 14.08 %, respectively. The study of the energy performance criteria shows that the MFPC is more suitable at lower volumetric flow rates and higher inlet fluid temperatures. Investigating the entropy generation and exergy destruction indicates that for every similar case the entropy generation and exergy destruction of the MFPC are lower than those of the CFPC. These interpretations, which are based on the energy, exergy, entropy generation and exergy destruction evaluations, recommend utilization of MFPCs instead of CFPCs.

Three-dimensional CFD analysis of PHWR exposed core under postulated severe accident condition

A three-dimensional steady-state thermal–hydraulic analyses of a large sized Pressurized Heavy Water Reactors (PHWRs) with varying levels of exposure is carried out for degraded core heat transfer assessment and presented in this paper. Low-frequency postulated severe accident without mitigating actions leads to exposure of fuel channels in PHWRs. Such exposure of fuel channels leads to their heat-up, governed by interdependent heat transfer mechanisms such as radiation, convection and conduction heat transfer and thermo-chemical interactions among the core constituents. In order to understand such complex behavior and plan the severe accident management guidelines, numerical analyses of the exposed core are of necessary. This paper illustrates the influence of the temperature and velocity profiles vis-à-vis different regions of the exposed core on the fuel channel heat-up. The interesting interdependency of convection and radiation heat transfer on fuel channel heat-up is reported. The dominance of convection heat transfer is observed for initial exposures of the fuel channels. However, the advanced stages of fuel channel exposures are observed to be dominated by radiation heat transfer. Intriguingly, it is observed that the convective cooling of exposed fuel channels by steam flow is counter-acted by exothermic heat generation from Zircaloy-made calandria tube surface and steam interaction. This leads to supplemental power addition for fuel channel heat-up. Moreover, it is interesting to note that the heat-up of fuel channels is restricted to central regions of the exposed core due to degraded steam cooling and higher-powered fuel channels. It is worth noting that fuel channel disassembly is observed in the advanced levels of fuel channel exposures. Moreover, fuel channel length equivalent to nearly 7–8 fuel bundle lengths undergo disassembly depending upon the fuel channel elevation and location in the core. The calandria vault water is observed to undergo film boiling at the onset of fuel channel disassembly.

Laser-induced growth of metal oxide films on quartz tubes for photocatalytic water treatments

A solid-state pulsed laser technique was developed to in situ grow arbitrary immobilized catalysts (Fe3O4, CeO2, WO3 etc.) on the inner surface of quartz tube with robust adhering strength. In a case study, anatase/rutile hetero-phase TiO2 film was deposited to serve as immobilized photocatalysts for the effective removal of antibiotics from aqueous environment. The X-ray absorption spectroscopy, low temperature electron paramagnetic resonance and the density functional theory simulation directly confirm a defect-assisted type-II band alignment was established to facilitate the charge transfer at the hereto-interphase. In addition, the oxygen vacancy enriched anatase phase with greater binding energy towards the dissolved oxygen facilitated the O2– generation. Meanwhile, the rutile phase enriched with Ti3+ could effectively activate the antibiotics to promote the direct h+ mediated oxidation. Such integration of unique atomic vacancies prevent defects from becoming electron-hole recombination centers and consequently extend the lifetime of the photoexcited charge carrier. The degradation mechanism of oxytetracycline was thoroughly examined by ultra-high resolution electrospray time-of-flight mass spectrometry and Fukui function, while the ecological structure–activity relationships program assessed the toxicity of contaminant to the environment. Milewhile, a continuous water treatment apparatus employing the catalytic tubes as reactors was established and demonstrated a ∼ 95 % OTC degradation under the natural sunlight adopting river water as the background. The experimental studies also claimed that ∼ 90 % of the initial activity could be retained after 100 cycles reuse, which permits their great potential for the applicational scenarios.

Investigating fouling deposition during combustion of hydrothermally treated palm empty fruit Bunch: Pilot-Scale study for industrial hydrothermal reactor

Inorganic elements in palm empty fruit bunch (EFB) are problematic in boiler operation, causing slagging and fouling deposits. The first pilot-scale hydrothermal treatment (HTT) system was commenced in a palm oil mill to remove undesirable elements. Fuel properties, combustion behavior, and fouling deposition of HTT-EFB were investigated. Liquid temperatures and treatment times in the HTT system significantly altered EFB-fuel properties. At ≥ 60 °C, potassium removals of at least 78 % were achieved, generating EFB-fuel containing potassium below 0.5 %wt. Later, a series of EFB combustion experiments were conducted in a specially designed fixed-bed reactor to simulate the tube surface of industrial boilers. Fouling deposition from HTT-EFB combustion reduced to below half of untreated EFB at all HTT conditions and combustion temperatures studied. The deposit-to-fuel ratio of HTT-EFB combusted at 1,000 °C was 37.3 % lower than untreated EFB combusted at a typical EFB boiler at 800 °C. Results demonstrated great potential for HTT-EFB in industrial applications.

Wind-Induced Response Analysis and Fatigue Reliability Study of a Steel–Concrete Composite Wind Turbine Tower

Taking an actual 3MW steel–concrete composite wind turbine tower as an example, a finite element model of the tower structure was established, and static bearing capacity and dynamic time history response analyses were performed to identify the locations where the structure is prone to failure. On this basis, the fatigue lives of the turbine tower at the most unfavorable locations were predicted using linear cumulative damage theory, and the fatigue reliability at the corresponding locations of the structure was calculated using the kriging–subset simulation method. The most dangerous locations of the tower that are most prone to failure are as follows: the bottom of the leeward side of the upper steel tube, the flange of the steel tube, the bolt-hole imprinting surface of the flange, the leeward side of the transition tube, and the top of the leeward side of the concrete tube. The failure risk of the flange and bolt-hole imprinting surface of the upper steel tube is relatively high, followed by that of the transition tube. This indicates that special attention should be given to the design and daily maintenance of this part. The fatigue resistance of the tower can be enhanced by improving the strength of the flange plate or increasing the number of bolts and strengthening the transition tube.

Full-field validation of finite cell method computations on wire arc additive manufactured components

Wire arc additive manufacturing enables the production of components with high deposition rates and the incorporation of multiple materials. However, the manufactured components possess a wavy surface, which is a major difficulty when it comes to simulating the mechanical behavior of wire arc additively manufactured components and evaluation of experimental full-field measurements. In this work, the wavy surface of a thick-walled tube is measured with a portable 3D scanning technique first. Then, the surface contour is considered numerically using the finite cell method. There, hierarchic shape functions based on integrated Legendre polynomials are combined with a fictitious domain approach to simplify the discretization process. This enables a hierarchic p-refinement process to study the convergence of the reaction quantities and the surface strains under tension–torsion load. Throughout all considerations, uncertainties arising from multiple sources are assessed. This includes the material parameter identification, the geometry measurement, and the experimental analysis. When comparing experiment and numerical simulation, the in-plane surface strains are computed based on displacement data using radial basis functions as ansatz for global surface interpolation. It turns out that the finite cell method is a suitable numerical technique to consider the wavy surface encountered for additively manufactured components. The numerical results of the mechanical response of thick-walled tubes subjected to tension–torsion load demonstrate good agreement with real experimental data, particularly when employing higher-order polynomials. This agreement persists even under the consideration of the inherent uncertainties stemming from multiple sources, which are determined by Gaussian error propagation.

Various methods for intraoperative neural monitoring during thyroid surgery

Intraoperative neural monitoring (IONM) during thyroidectomy is an essential technique to safeguard the recurrent laryngeal nerve (RLN) and the external branch of the superior laryngeal nerve (EBSLN), both critical for vocal cord function. Utilizing electromyography (EMG), IONM provides real-time feedback on nerve integrity, significantly reducing the risk of nerve damage during surgery. The primary methods of IONM include endotracheal tube electrodes, surface electrodes, needle electrodes, and continuous monitoring, each with distinct advantages and limitations. Endotracheal tube electrodes offer direct measurements but can be difficult to position, while surface electrodes are non-invasive but may experience signal interference. Needle electrodes provide precise measurements but are invasive, and continuous monitoring offers ongoing feedback but requires advanced equipment. The evolution of IONM began in the mid-20th century and has progressed significantly, leading to its widespread adoption in thyroid surgery by the mid-2000s. Enhanced by recent technological advancements and standardized by professional guidelines, IONM has become integral in reducing postoperative complications. Ongoing research aims to further refine IONM techniques, ensuring optimal patient outcomes and the preservation of nerve function in thyroid surgery.

Essential principles for blood centrifugation.

Currently, autologous platelet concentrates (APCs) are frequently used for soft- and hard-tissue regeneration, not only within the oral cavity, but also extra-orally including chronic wounds, burns, joints, dermatological conditions, among others. The benefits of APCs are largely influenced by the treatment strategy but also their preparation. This paper therefore discusses in detail: the physical properties of blood cells, the basic principles of blood centrifugation, the impact of the centrifugation protocol (rotations/revolutions per minute, g-force, variation between centrifuges), the importance of timing during the preparation of APCs, the impact of the inner surface of the blood tubes, the use/nonuse of anticoagulants within APC tubes, the impact of the patient's hematocrit, age, and gender, as well as the important requirements for an optimal centrifugation protocol. All these variables indeed have a significant impact on the clinical outcome of APCs.

Experimental Study of Condensation Heat Transfer and Droplet Dynamics on Multiple Horizontal Copper Tubes with Superhydrophobic Characteristics

We conducted an experimental study on the condensation heat transfer and droplet dynamics on multiple horizontal copper tubes with superhydrophobic characteristics. Condensation heat transfer has various industrial applications such as power plants and air-conditioning systems. Because condensers are typically designed in multiple-tube configurations, studying the phenomenon of multiple tubes is important. We investigated the effect of a superhydrophobic surface modification, which induces dropwise condensation, on the heat transfer performance of multiple-tube condensers. The purpose of this research is to evaluate the extent to which heat transfer performance is improved by comparing superhydrophobic tubes with bare tubes and to analyze the impact of droplet dynamics on heat transfer performance. The results show that the heat transfer coefficient of the superhydrophobic tubes is improved by approximately 9.5%–44.9% compared to that of bare tubes. Droplet dynamic analysis revealed differences in droplet behavior between the superhydrophobic tubes and bare tubes, including the formation of droplets by condensation, the process of droplets falling on the tube surface, and the impact of droplets falling on other tubes in a multiple-tube configuration. Based on these results and observations, it can be concluded that the heat transfer performance of the superhydrophobic tube is superior to that of the bare tube. The droplet dynamic analysis demonstrated that the droplets formed on the superhydrophobic surface could be easily removed by the flow, leading to more efficient heat transfer. These findings highlight the potential for more efficient heat transfer in multiple tubes through superhydrophobic modifications.