Sufficient Strength Research Articles

Fabrication and Characterization of Jute Fibre Reinforced Polymer-based Decorative Composites: Effect of Gamma Radiation

The jute fibre (JF) reinforced polyethylene (PE), polypropylene (PP), and epoxy resin (ER) matrix composites were developed. The JF content was maintained to 30% by weight. Then tensile properties and impact strength were measured. The finest tensile properties were found for JF/PP composites. The tensile strength (TS), tensile modulus (TM), elongation at break (Eb%), and impact strength (IS) of the JF/PP composites were found to be 38.00 MPa, 1800 MPa, 12%, and 8.20 kJ/m2 respectively. The bonds between JF and polymers of the developed composites were investigated and found good adhesion. The composite samples were exposed to gamma ray and it was found that gamma radiation have the potential to improve the tensile and impact strength of the JF-based polymer composites. The JF content polymer-based decorative composites were also developed. The outcomes of this investigation showed a minor decrease of the tensile and impact strength of the composites but enhanced the beauty of the composites noticeably. The developed JF/polymer composites have sufficient mechanical strength for many applications pretty. J. of Sci. and Tech. Res. 5(1): 75-82, 2023

Logical Resonance in Izhikevich Neuron

This paper proposes a new logic element model based on an Izhikevich (IZ) neuron and neural system that emulates two- and three-state logic behaviours. In a noise-free environment, with a periodic current of suitable amplitude and frequency, the IZ system is capable of performing logical AND and OR operations. Initially, a single IZ neuron demonstrates membrane dynamics in response to an input signal generated by combining two-state logic currents below the threshold. Subsequently, an IZ neural system model is introduced to enhance the reliability and resilience of the system. This model is characterised by electrical coupling with fast conduction and chemical coupling with a more adaptable structure. Each logic input independently influences each neuron within the system. Additionally, it has been observed that the reliability of the logic element is influenced by changes in synaptic strength, with a neural system lacking sufficient synaptic strength failing to generate logical output. Furthermore, the system displays a three-state logic behaviour under suitable forcing periodicity, thus enhancing the power efficiency of the logic element. The proposed IZ neuron and neural system are expected to significantly impact the development of brain-inspired logic elements.

Degradation of Unsintered Hydroxyapatite and Poly-L-Lactide Composite Sheets In Vivo and In Vitro.

Bioabsorbable sheet-shaped implants made of forged composites of unsintered hydroxyapatite and poly-L-lactide (F-u-HA/PLLA) have been used for orbital fracture repair with good results. This is the first report using multiple specimens implanted in the human orbit to demonstrate the biodegradation and loss of strength of F-u-HA/PLLA sheets. Among the patients who underwent various facial fracture repairs with F-u-HA/PLLA sheets implanted in their orbits, those whose sheets were subsequently extracted were included in the study. Viscosity-average molecular weight, crystallinity, and bending strength of the extracted implants were measured. An in vitro degradation test was also performed for comparison. Among the 111 patients who underwent F-u-HA/PLLA sheet implantation, 13 subsequently underwent surgical extraction of implants; the majority were due to secondary correction of complex fractures. One patient developed an infection; none developed foreign body reactions. Overall, 11 specimens from 10 patients with consent were examined. The time from implantation to extraction ranged from 43 to 632 days (median: 210d). Compared with the results of the in vitro degradation test, the viscosity-average molecular weight and bending strength had a slower decrease. The F-u-HA/PLLA sheets retained more than 50% of their initial bending strength after 12 months. Crystallinity varied widely. F-u-HA/PLLA sheets implanted in human orbits did not degrade faster than those of in vitro testing. Sheet-shaped implants made of forged composites of unsintered hydroxyapatite and poly-L-lactide can be considered appropriate reconstructive materials for orbital fractures as they retained sufficient strength to support the orbital contents at 12 months postoperatively, and no case of delayed foreign body reactions was observed.

In Vitro Corrosion of Polyester-Coated Magnesium Alloy under pH-Static Conditions.

The resorption rate of bioresorbable implants requires tuning to match the desired field of application. The use of Mg as implant material is highly advantageous, as it provides sufficient mechanical strength combined with its biodegradability. Consequently, the implant vanishes after it has served its intended purpose, allowing the complete restoration of natural tissue and organ function. However, a biodegradable Mg implant requires a biodegradable coating to slow the rate of Mg corrosion, as a permanent coating would negate the benefits of using Mg as an implant material. Therefore, degradable polymers are the materials of choice, especially polyester-based coatings, such as PLLA, as they have been proven in clinical practice over the long term. Within this work, the degradation retarding effect of a physical barrier in form of four clinically relevant polyester-based coatings, poly-l-lactide (PLLA), poly-l-lactide-co-glycolide (PLGA), poly(l-lactide-co-PEG) triblock copolymer (PLLA-co-PEG), and polydioxanone (PDO), is investigated in vitro under pH-static conditions using CO2 gas to compensate pH changes due to Mg corrosion. Coating thicknesses of 7.5 to 8.3 μm were comparable to commercially available stent systems. Quantitative analysis of magnesium concentration in buffered test medium by a photometric assay allows real-time monitoring. Shielding effect of different polyesters through polymer coating and formation of a protective passivation layer beneath the polymer coating was observed and characterized using SEM and EDX techniques. Our finding was that even imperfect polymer layers provide a considerable protective effect, and the used in vitro setup matches reported in vivo observations regarding elemental composition of corrosion products.

Calcium Phosphates: A Key to Next-Generation In Vitro Bone Modeling.

The replication of bone physiology under laboratory conditions is a prime target behind the development of in vitro bone models. The model should be robust enough to elicit an unbiased response when stimulated experimentally, giving reproducible outcomes. In vitro bone tissue generation majorly requires the availability of cellular components, the presence of factors promoting cellular proliferation and differentiation, efficient nutrient supply, and a supporting matrix for the cells to anchor - gaining predefined topology. Calcium phosphates (CaP) are difficult to ignore while considering the above requirements of a bone model. Therefore, the current review focuses on the role of CaP in developing an in vitro bone model addressing the prerequisites of bone tissue generation. Special emphasis is given to the physico-chemical properties of CaP that promote osteogenesis, angiogenesis and provide sufficient mechanical strength for load-bearing applications. Finally, the future course of action is discussed to ensure efficient utilization of CaP in the in vitro bone model development field.

An Injectable Thermosensitive Hydrogel with Antibacterial and Antioxidation Properties for Accelerating Wound Healing.

As a new type of wound dressing, hydrogels have attracted more and more attention. However, traditional hydrogel wound dressings lack inherent antibacterial properties and are difficult to match irregular wounds, which leads to an easy wound bacterial infection. To solve the problems associated with traditional hydrogels, in this research, a thermosensitive hydrogel (PFLD) for wound dressings was developed based on Poloxamer 407 (PF127), lysine (Lys), and 3,4-dihydroxyphenylacetic acid (DOPAC). Rheological tests indicated that the PFLD hydrogel possesses injectability, adaptability to deformation, and sufficient mechanical strength for wound dressing applications. In addition, it could in situ gel at 33 °C, which indicated that the hydrogel could undergo sol-to-gel transition under body temperature. Upon using it in wound treatment, it could adapt to irregular wounds to achieve full coverage of the wound and promote the rapid hemostasis of wound bleeding. Due to the presence of DOPAC in the hydrogel, it exhibited excellent antibacterial and antioxidant properties on the wounds. The skin defect model showed that the wound shrinkage was the fastest after PFLD hydrogel treatment. On day 14, the wound shrinkage rates were 81.68 and 99.77% for the control and PFLD hydrogel groups, respectively. Therefore, the PFLD hydrogel has a broad application prospect as a dressing for the treatment of irregular wounds.

Bond line shear strength of structural wood adhesives at high temperatures up to wood carbonization – A classification approach

The European timber fire design code EN 1995-1-2 presently specifies that adhesives for timber construction products shall provide integrity throughout the intended fire exposure time, yet no test or requirement specifications are given. Contrary, in North America elevated temperature tests are mandatory and product standards for glued and cross laminated timber demand sufficient bond line shear strength up to 220 °C. This paper deals with block shear compression tests at ambient and elevated temperatures for development of a high temperature resistance classification system for structural wood adhesives. The investigations comprised 1200 specimens made from Norway spruce bonded with twelve brands from five adhesive families. Polycondensation (pcon) resins encompassed phenolic resorcinol formaldehyde, melamine urea formaldehyde and melamine formaldehyde adhesives. Polyaddition (padd) adhesives comprised five one-component polyurethanes and an emulsion polymer isocyanate. The focus was on the strength-temperature (fv-T) relationship of bonded and solid wood reference specimens at 180–270 °C. The pcon adhesives showed almost throughout a fv-T relationship close to solid wood up to 270 °C. Contrary, the padd adhesives revealed massive strength degradations vs. solid wood from 180 °C onwards. An adhesive test, evaluation and classification procedure with four classes T270 to T200 was derived. It is based on a comparison of the temperature-dependent shear strength decline in bonded samples vs. solid wood reference samples beyond 180 °C. Class T270 adhesives are proposed being suited for the linear charring model of EN 1995-1-2 as PRF adhesives without additional fire resistance testing of components deemed necessary today.

Parametric design methodology for yoke-magnetization in magnetic flux leakage detection systems

Magnetic flux leakage (MFL) testing is a widely employed non-destructive testing (NDT) method, particularly for ferromagnetic materials. This paper proposes a systematic design procedure for the yoke-magnetization component in MFL systems utilizing permanent magnets. The dimensions of the yoke-magnetization are parameterized, and the design methodology is formulated in the form of analytical equations based on fundamental engineering principles and optimization techniques. The proposed design procedure outlines all the required parameters and metrics to establish a yoke-magnetization configuration tailored for a specified application, thereby facilitating scalability. The theoretical framework identifies the optimal operating point that maximizes leakage flux while minimizing the magnetic field amplitude. A genetic algorithm is employed to minimize the dimensions of the permanent magnets while maintaining a sufficient magnetic field strength for specimen magnetization. An experimental setup is constructed to validate the accuracy of the proposed design procedure. The experimental results exhibit consistency with finite element method (FEM) simulations conducted using a case study. Specifically, the findings reveal that the thickness of the magnetic bridge significantly impacts the leakage fluxes at defect sites within the specimen. When the thickness of the magnetic bridge is 10 mm, slightly smaller than the optimal thickness of approximately 11 mm, the leakage flux at the defect site leaks out towards the surrounding air insignificantly. In contrast, a thickness of 15 mm is observed to strongly improve the leakage flux at the defect site.

Water stress corrosion at wafer bonding interface during bond strength evaluation

Wafer-to-wafer bonding is becoming a critical unit process step with the increase in the demand for 3D integration. The widely used bonding method is plasma activated bonding, where it is essential to ensure sufficient bond strength to withstand the stresses generated during subsequent processes and achieve multi-layer stacking or layer transfer. Although the double cantilever beam method is widely used to evaluate wafer bond strength, significant variation occurs due to water stress corrosion at the bonding interface. These factors have not been adequately addressed, and precise measurement conditions have yet to be established. In this study, a semi-auto tool was introduced to conduct measurements under an inert atmosphere, whereby the influence of water stress corrosion was eliminated. Furthermore, the study elucidated the effects of the crystal orientation and blade insertion conditions. The impacts of interfacial voids and the annealing conditions on bond strength were revealed. Observation of the progress of delamination during measurements under an inert atmosphere enabled the effective estimation of the moisture content that remained inside the wafers, which then contributed to the selection of appropriate annealing conditions.

Characterization of biological and mechanical properties of 3D-bioprinted osteochondral plugs

Three-dimensional (3D) bioprinting offers significant potential for the repair of articular cartilage by engineering functional osteochondral tissue. However, progress has been hindered by a lack of printable bioinks that promote the development of bone and chondral tissue while also maintaining sufficient cytocompatibility and mechanical strength. Herein, we designed a biphasic osteochondral plug with distinct chondral and bone regions and developed suitable bioinks for each tissue using photorheology and compression testing. The chondral region consisted of human bone marrow-derived mesenchymal stem cells (hbMSCs) encapsulated in a chondral bioink composed of methacrylated hyaluronic acid and high molecular weight hyaluronic acid. The bone region was 3D bioprinted from an hbMSC-laden methacrylated gelatin (GelMA) bioink and a biodegradable thermoplastic and ceramic lattice that provided mechanical strength. The viability and functionality of hbMSC encapsulated in the bioinks were confirmed through live/dead assays, histology, biochemical assays, and fluorescence microscopy. Over 56 days of culture in a chondrogenic medium, hbMSCs encapsulated in chondral bioink deposited cartilage-like extracellular matrix components, such as type II collagen and glycosaminoglycans. Similarly, cells encapsulated in the bone bioink and cultured in osteogenic medium deposited hydroxyapatite, a key component of bone. These findings provide promising initial results for using 3D-bioprinted plugs to repair osteochondral defects in articular cartilage.  

Interfacial charge demulsification endowed dual-network photocatalytic hydrogen-bonded PVA@agarose membranes for oil-water separation

Hydrogel materials with hydrophilic cross-linked network exhibit remarkable super-wettability, enabling their widespread application in oily wastewater treatment. However, the single and loose structure lacks sufficient strength and porosity to resist long-term degradation. Herein, a structural synergistic molecular strategy was reported to introduce reinforcing phase structures and interfacial active sites into the polymer networks for long-term oil-water emulsion separation. The carbon skeleton was uniformly interspersed through the strongly hydrogen-bonded polymer chains via covalent bonds, resulting in a hydrogel network with high mechanical strength and exceptional flow conductivity, which maintained a separation flux of 1233 L m−2 h−1 after 20 separation cycles under gravitational force. Dense negative charges on the surface disrupted the internal charge stability of the oil-water emulsion, leading to remarkable demulsification with a separation efficiency exceeding 99 %. Simultaneously, the strong redox reaction of the photoheterojunction effectively removed organic dyes under visible light, enhancing the overall antifouling performance. This study provided a feasible strategy at the molecular level for optimizing the suitability of hydrogels for oil-water emulsion separation.

Using a Model Created Using a 3D Printer to Mould a Grey Cast Iron Casting.

This article deals with the possibility of using 3D-printed models as an input for the production of a mould for cast iron castings. This new progressive process is significantly faster (with sufficient accuracy) compared to the current way of making models for moulds. The need to create a wooden model is removed by this process. The quality of this wooden model was highly dependent on the experience and qualifications of the worker. This article describes the manufacturing process of the model and mould in detail. The key dimensions of the final parts are compared with the model and, thus, the accuracy of the chosen procedure is verified. A 3D-printing technology known as Multi Jet Fusion (MJF) was used to produce the model. The material used for the production of the model is polyamide PA12 with 40% glass fibre filling. This material has sufficient structural and strength properties to be used for the given application. Taking into account the dimensions of the part and the printing space of the printer, it was necessary to structurally modify and divide the part. The inlet cone of a turbine is used as an example This cone is produced from grey cast iron as standard.

First-principles study of the stability and mechanical properties for binary Mo–Re alloys

Mo–Re alloys are highly suitable as core materials in nuclear reactor applications due to their excellent radiation resistance, high melting point, superior mechanical strength, and low neutron absorption characteristics. In this study, we investigate the stability and mechanical properties of eight Mo–Re alloys by first-principles calculations, including Re24Mo5, ReMo3-1, ReMo3-2, Re3Mo2, ReMo, Re3Mo-1, Re3Mo-2, Re3Mo-3. The results of formation enthalpy, elastic stability criteria and phonon dispersion curves indicate that all Mo–Re alloys are stable except for the ReMo3-2. Subsequently, the mechanical parameters of the remaining seven Mo–Re alloys, including bulk modulus, shear modulus, Young's modulus, Poisson's ratio, B/G ratio, and anisotropy index are investigated. The bulk modulus of Re24Mo5 is the highest, at 344.597 GPa, the Young's modulus and shear modulus of Re3Mo-3 are the highest, measuring 390.617 GPa and 149.294 GPa, respectively. Furthermore, all Mo–Re alloys exhibit ductile characteristics. This study is of great significance for the selection of suitable Mo–Re alloys with sufficient mechanical strength for use as core materials.

Development of Epoxy-Resin Based Solid Electrolytes for Multifunctional Structural Batteries

A structural battery is defined as being multifunctional; it is a load bearing system with some electrochemical energy storing capability. The electrolyte system is the key enabler for a multifunctional structural battery as it must possess sufficient ionic conductivity (~10-4S/cm) and mechanical strength (Youngs’s modulus ~ 600-900 MPa) simultaneously. Polymeric systems offer the best possible scenario for practical realization of multifunctional structural batteries due to a set of favorable properties, such as reasonable ionic conductivity, easy processability etc. In the present work, we focus on the development of a dual-phase structural battery electrolyte to optimize ionic conductivity and mechanical performance simultaneously. An epoxy resin-based system is chosen due to its high mechanical strength and its ability for in-situ polymerization that leads to a unique microstructure promoting multi-functionality. Diglycidyl ether of Bisphenol A (DGEBA) accounts for the epoxy to provide hard segments in the matrix and is cured by an amine compound (Jeffamine T-403). A liquid electrolyte is added to the system for improving ionic conductivity without compromising its mechanical strength substantially. Multiple liquid components consisting of lithium salt and solvents are considered -lithium bis(trifluoromethanesulfonyl)imide (LITFSI) dissolved in a solution of ethylene carbonate (EC) and dimethyl methyl phosphonate (DMMP) and LiTFSI dissolved in 1-Ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (EMIM-TFSI). Ionic conductivity of the electrolyte systems as a function of temperature is measured utilizing electrochemical impedance spectroscopy. Uniaxial load tests are performed to evaluate the mechanical properties (e.g., Young’s modulus, Yield strength) of the epoxy-based electrolyte systems with and without the addition of the ion conducting liquids. Comparative data on the epoxy-based systems containing varying amounts of liquid components will be presented.

Evaluating the performance of Bi58Sn42 mold produced by material extrusion additive manufacturing system for agile manufacturing

PurposeThe purpose of this study is to produce a low-cost sheet metal forming mold made from the low melting point Bi58Sn42 (bismuth) alloy by using an open-source desktop-type material extrusion additive manufacturing system and to evaluate the performance of the additively manufactured mold for low volume sheet metal forming. Thus, it was aimed to develop a fast and inexpensive die tooling methodology for low-volume batch production.Design/methodology/approachInitially, the three-dimensional printing experiments were performed to produce the sheet metal forming mold. The encountered problems during the performed three-dimensional printing experiments were analyzed. Accordingly, both tunings in process parameters (extrusion temperature, extrusion multiplier, printing speed, infill percentage, etc.) and customizations on the extruder head of the available material extrusion additive manufacturing system were made to print the Bi58Sn42 alloy properly. Subsequently, the performance of the additively manufactured mold was evaluated according to the dimensional change that occurred on it during the performed pressing operations.FindingsResults showed that the additively manufactured mold was rigid enough and proved to have sufficient strength in sheet metal forming operations for low-volume production.Originality/valueAlternative mold production was carried out using open-source material extrusion system for low volume sheet metal part production. Thus, cost effective solution was presented for agile manufacturing.

Synergistic effects of chitosan and gamma irradiation on enhanced fungal growth inhibition and biodegradability of natural rubber latex film

Developing novel formulations and processes to improve the fungal growth inhibition and biodegradability of NR products has become a major challenge for the scientific community, given the health risks associated with fungi in natural rubber (NR) products and the environmental concerns regarding NR waste. Consequently, this study comprehensively investigated the synergistic effects of chitosan and gamma irradiation on enhancing fungal growth inhibition and biodegradability in natural rubber latex (NRL) films. The research involved incorporating varying chitosan contents (0, 3, 6, or 9 phr) into NRL composites and exposing them to different gamma doses (0, 5, 10, or 15 kGy). The results showed that increasing the chitosan content and the gamma dose improved the ability of the NRL samples to inhibit fungal growth on their surfaces. This was evidenced by the absence of fungal colonies after 7 days of incubation on potato dextrose agar (PDA) plates for NRL samples irradiated at 5–15 kGy with 9 phr of chitosan. This determination was based on isolating fungi from the film surfaces, followed by serial dilution and a viable plate count. The biodegradability tests also revealed that the NRL films irradiated at 15 kGy with 9 phr of chitosan had the highest weight loss, reaching as high as 10.42 ± 0.62 % after soil burial for 8 weeks. However, the results indicated that gamma irradiation on the pristine NRL and chitosan/NRL films did not substantially alter the thermal stabilities, density, morphology, and functional groups of the samples. Lastly, by comparing the tensile properties of all the NRL films to the ASTM D3578-01a standard for examination gloves, the optimum conditions for the NRL films were 5 kGy of gamma irradiation with 9 phr of chitosan. This combination resulted in gloves with sufficient tensile strength and complete fungal growth inhibition.

Prosthetics of heart valves: current trends

Nowadays, cardiac surgery is highly safe in terms of protecting internal organs from ischemia and cardioplegia. This allows for radical interventions even in weakened patients with risk factors for perioperative mortality. At the same time, classical heart valve replacement operations are suboptimal and invalidate the patient. The purpose of the study is a critical analysis of the current state of the problem of prosthetics of heart valves, evaluation of alternative methods of prosthetics. To replace the atrioventricular valve, the most suitable bioprosthesis may be a human mitral allograft, which allows you to fully replace the complex structures of the AV valve due to the identity of the anatomy, can work cooperatively with all functional structures of the left ventricle, has the potential to repopulate the patient’s tissues, sufficient strength and a relatively simple and permanent anatomy (compared with tricuspid allograft), while it is safe in terms of rejection. Currently, there is a large set of alternative options for prosthetics of heart valves. Many of them are characterized by greater physiology, anatomicity, and safety in terms of prosthesis-dependent complications compared to classic skeleton prostheses.

Dissolving microneedle integrated with benidipine loaded ethosomes for transdermal delivery

Benidipine HCl (BEN) is a drug used for the treatment of hypertension. However, this drug suffers from low oral bioavailability. This study introduces a novel approach to address this issue by developing BEN-loaded ethosomes (BEN-E) that integrate into dissolving microneedles for transdermal delivery. The BEN-E was prepared using a rotary evaporation method and optimised using the Box-Behnken design. Following that, the optimised BEN-E formulation was integrated into dissolving microneedles (DMNs). The optimised lipid vesicles selected comprised lipoid S75 (339.66 mg), ethanol (34.51 %), and sonication time (70 s) and showed a vesicle size of 149.4 ± 3.81 nm, an EE% of 88.57 ± 0.38 %, and a transdermal flux of 19.12 ± 0.19 μg/cm²/hr. On the other hand, the resulting BEN-E-DMNs exhibited sharp pyramidal microneedles, sufficient mechanical strength, good insertion capability, and fast dissolution in rat skin. In the ex vivo study, the permeation coefficient of BEN was significantly improved by BEN-E-DMNs compared with optimised BEN-E and BEN-DMNs. The pharmacokinetic studies showed that the BEN-E-DMNs had a Cmax of about 0.698 ± 0.037 μg/mL and an AUC₀₋ₜ of about 15.821 ± 0.868 μg/hr/mL. Moreover, it improved the relative bioavailability of BEN by about 1.58 times compared to the orally marketed BEN tablet and about 2.95 times compared to the BEN-DMNs. In conclusion, the ethosomes combined with dissolving microneedles have shown high potential as carriers for the transdermal delivery of BEN.

Tension Capacity of Crushed Limestone-Cement Grout.

The feasibility of using crushed limestone instead of sand in cement grout is examined in this work. This study entails performing several tests, including the Brazilian test, the compressive strength test, and the stress-strain correlation test. The curing times used were 7, 14, and 28 days for mixtures with various proportions of cement to limestone (1:1, 1:2, and 1:4). The conventional sand-cement grout laboratory tests were prepared using a similar methodology to examine the effectiveness of the suggested substitute. The findings show that the limestone-based grout has sufficient strength, but that it is less than that of the typical sand material. The values of the tensile strength and elastic modulus were determined. A focus was made on the tensile strength and stress-strain relationship. A special laboratory set-up was used to look at the progress of failure using strain gauges fitted to the cylindrical samples both vertically and horizontally. The angular shape of the particles' ability to interlock is responsible for the material's increase in strength. According to this study, crushed limestone can be used as a substitute for sand in circumstances where sand supply is constrained. The suggested grout can be used in the shotcrete of tunnels and rock surfaces.

Sustained release microneedle patch for pronounced systemic delivery of doxazosin mesylate

Introduction: Microneedle patch is one of the fascinating drug delivery approaches that offers low invasiveness and a painless physical application to enhance the delivery of micro and macro-molecules into the skin. Methods: Variable contents of chitosan and polyvinyl alcohol were used for the development of doxazosin mesylate containing sustained release microneedle patches via solvent casting technique. The prepared patches were evaluated for microscopic evaluation, mechanical strength, drug loading (%) and Fourier transform infrared spectroscopy (FTIR) etc. The skin penetration study was performed by using pig ear skin and results were captured through confocal microscopy. Ex-vivo release study and pharmacokinetic evaluation were also performed. Results: Sharp needle tips with a height of 600µm and a base of 200µm were confirmed through microscopic examination. Optimized formulation (SRF-6) exhibited loading of 92.11% doxazosin mesylate with appreciable strength up to 1.94N force. Ex-vivo release studies revealed 87.24% release within 48 hours. Moreover, the pharmacokinetic parameters in case of optimized patch formulation (SRF-6) were markedly improved i.e. MRT (19.46 h), AUC (57.12 μg.h /mL), Cmax (2.16 µg /mL), tmax (10.10 h) and t1/2 (6.32 h) as compared to commercially available tablet. Biocompatibility of the developed patches was validated from skin irritation studies. Conclusion: Results confirmed the successful fabrication of microneedle patch having sufficient strength and effective penetration ability into the skin to ensure controlled release of incorporated drug for the intended duration. It can be employed as an efficient carrier system for other therapeutics those are prone to bioavailability issues due to first pass effect after their oral administration.