Substrate-triggered Technique Research Articles

Design and analysis of different trigger techniques for ESD clamp circuit in 0.5-µm 5 V/18 V CDMOS process

In this work, gate-driven, substrate-triggered and gate-substrate-triggered techniques for both 5V NMOS-based and 18V NLDMOS-based power clamps under electrostatic discharge (ESD) stress were investigated in details. Schematics of the three trigger designs were depicted and their physical mechanisms were studied at first. To verify and make comparisons of their performance, they were fabricated in a standard 0.5-μm 5V/18V CDMOS process and characterized by transmission line pulse (TLP) test system, respectively. Experimental results show that 5V NMOS-based power clamp with substrate-triggered technique has the lowest trigger voltage (∼8.37V) and the highest failure current (∼3.58A), and 18V gate-substrate-triggered design based on NLDMOS has low trigger voltage (∼34.02V) and greatest robustness (It2=3.32A). Therefore, as for low-voltage NMOS-based ESD power clamps, substrate-triggered design obtains the most superior ESD protection performance; but for high-voltage power clamps, gate-substrate-triggered technique can make NLDMOS actualize uniform current conduction and better ESD robustness.

Design of High-Voltage-Tolerant ESD Protection Circuit in Low-Voltage CMOS Processes

Two new electrostatic discharge (ESD) protection design by using only 1 times VDD low-voltage devices for mixed-voltage I/O buffer with 3 times VDD input tolerance are proposed. Two different special high-voltage-tolerant ESD detection circuits are designed with substrate-triggered technique to improve ESD protection efficiency of ESD clamp device. These two ESD detection circuits with different design concepts both have effective driving capability to trigger the ESD clamp device on. These ESD protection designs have been successfully verified in two different 0.13-mum 1.2-V CMOS processes to provide excellent on-chip ESD protection for 1.2-V/3.3-V mixed-voltage I/O buffers.

ESD protection circuit with low triggering voltage and fast turn-on using substrate-triggered technique

In this paper, ESD protection circuit with substrate-triggered technique using PNP bipolar transistor for quick discharge of the electrostatic energy is proposed. The proposed ESD protection circuit is verified by the transmission line pulse (TLP) system. The results show that the proposed ESD protection circuit has lower trigger voltage (5.98V) compared with that of conventional GGNMOS. And the proposed circuit has faster turn-on time (∼37ns) than that of the conventional substrate-triggered ESD protection circuit.

Design on Power-Rail ESD Clamp Circuit for 3.3-V I/O Interface by Using Only 1-V/2.5-V Low-Voltage Devices in a 130-nm CMOS Process

A new power-rail electrostatic discharge (ESD) clamp circuit for application in 3.3-V mixed-voltage input-output (I/O) interface is proposed and verified in a 130-nm 1-V/2.5-V CMOS process. The devices in this power-rail ESD clamp circuit are all 1-V or 2.5-V low-voltage nMOS/pMOS devices, which are specially designed without suffering the gate-oxide reliability issue under 3.3-V I/O interface applications. A special ESD detection circuit realized with the low-voltage devices is designed and added in the power-rail ESD clamp circuit to improve ESD robustness of ESD clamp devices by substrate-triggered technique. The experimental results verified in a 130-nm CMOS process have proven the excellent effectiveness of this new proposed power-rail ESD clamp circuit

ESD protection design for I/O cells with embedded SCR structure as power-rail ESD clamp device in nanoscale CMOS technology

This paper presents a new electrostatic discharge (ESD) protection design for input/output (I/O) cells with embedded silicon-controlled rectifier (SCR) structure as power-rail ESD clamp device in a 130-nm CMOS process. Two new embedded SCR structures without latchup danger are proposed to be placed between the input (or output) pMOS and nMOS devices of the I/O cells. Furthermore, the turn-on efficiency of embedded SCR can be significantly increased by substrate-triggered technique. Experimental results have verified that the human-body-model (HBM) ESD level of this new proposed I/O cells can be greater than 5 kV in a 130-nm fully salicided CMOS process. By including the efficient power-rail ESD clamp device into each I/O cell, whole-chip ESD protection scheme can be successfully achieved within a small silicon area of the I/O cell.

SCR Device Fabricated With Dummy-Gate Structure to Improve Turn-On Speed for Effective ESD Protection in CMOS Technology

Turn-on speed is the main concern for an on-chip electrostatic discharge (ESD) protection device, especially in the nanoscale CMOS processes with ultrathin gate oxide. A novel dummy-gate-blocking silicon-controlled rectifier (SCR) device employing a substrate-triggered technique is proposed to improve the turn-on speed of an SCR device for using in an on-chip ESD protection circuit to effectively protect the much thinner gate oxide. The fabrication of the proposed SCR device with dummy-gate structure is fully process-compatible with general CMOS process, without using an extra mask layer or adding process steps. From the experimental results in a 0.25-/spl mu/m CMOS process with a gate-oxide thickness of /spl sim/50 /spl Aring/, the switching voltage, turn-on speed, turn-on resistance, and charged-device-model ESD levels of the SCR device with dummy-gate structure have been greatly improved, as compared to the normal SCR with shallow trench isolation structure.

ESD protection design for mixed-voltage I/O buffer with substrate-triggered circuit

A substrate-triggered technique is proposed to improve the electrostatic discharge (ESD) robustness of a stacked-nMOS device in the mixed-voltage I/O circuit. The substrate-triggered technique can further lower the trigger voltage of a stacked-nMOS device to ensure effective ESD protection for mixed-voltage I/O circuits. The proposed ESD protection circuit with substrate-triggered design for a 2.5-V/3.3-V-tolerant mixed-voltage I/O circuit has been fabricated and verified in a 0.25-/spl mu/m salicided CMOS process. The substrate-triggered circuit for a mixed-voltage I/O buffer to meet the desired circuit application in different CMOS processes can be easily adjusted by using HSPICE simulation. Experimental results have confirmed that the human- body-model (HBM) ESD robustness of a mixed-voltage I/O circuit can be increased /spl sim/60% by this substrate-triggered design.

On-Chip ESD Protection Design With Substrate-Triggered Technique for Mixed-Voltage I/O Circuits in Subquarter-Micrometer CMOS Process

A new electrostatic discharge (ESD) protection design, by using the substrate-triggered stacked-nMOS device, is proposed to protect the mixed-voltage I/O circuits of CMOS ICs. The substrate-triggered technique is applied to lower the trigger voltage of the stacked-nMOS device to ensure effective ESD protection for the mixed-voltage I/O circuits. The proposed ESD protection circuit with the substrate-triggered technique is fully compatible to general CMOS process without causing the gate-oxide reliability problem. Without using the thick gate oxide, the new proposed design has been fabricated and verified for 2.5/3.3-V tolerant mixed-voltage I/O circuit in a 0.25-/spl mu/m salicided CMOS process. The experimental results have confirmed that the human-body-model ESD level of the mixed-voltage I/O buffers can be successfully improved from the original 3.4 to 5.6 kV by using this new proposed ESD protection circuit.

Latchup-free esd protection design with complementary substrate-triggered scr devices

The turn-on mechanism of silicon-controlled rectifier (SCR) devices is essentially a current triggering event. While a current is applied to the base or substrate of an SCR device, it can be quickly triggered on into its latching state. In this paper, latchup-free electrostatic discharge (ESD) protection circuits, which are combined with the substrate-triggered technique and an SCR device, are proposed. A complementary circuit style with the substrate-triggered SCR device is designed to discharge both the pad-to-V/sub SS/ and pad-to-V/sub DD/ ESD stresses. The novel complementary substrate-triggered SCR devices have the advantages of controllable switching voltage, adjustable holding voltage, faster turn-on speed, and compatible to general CMOS process without extra process modification such as the silicide-blocking mask and ESD implantation. The total holding voltage of the substrate-triggered SCR device can be linearly increased by adding the stacked diode string to avoid the transient-induced latchup issue in the ESD protection circuits. The on-chip ESD protection circuits designed with the proposed complementary substrate-triggered SCR devices and stacked diode string for the input/output pad and power pad have been successfully verified in a 0.25-/spl mu/m salicided CMOS process with the human body model (machine model) ESD level of /spl sim/7.25 kV (500 V) in a small layout area.

Substrate-triggered technique for on-chip ESD protection design in a 0.18-μm salicided CMOS process

The substrate-triggered technique for input, output, and power-rail electrostatic discharge (ESD) protection, as comparing to the traditional gate-driven technique, has been proposed to effectively improve ESD robustness of IC products. With the substrate-triggered technique, on-chip ESD protection circuits for the input, output, and power pins have been designed and verified in a 0.18-/spl mu/m salicided CMOS process. The experimental results have confirmed that the proposed substrate-triggered design can effectively and continually improve ESD robustness of CMOS devices. The human-body-model (HBM) ESD robustness of NMOS with a device dimension of W/L=300 /spl mu/m/0.3 /spl mu/m can be improved from the original 0.65 kV with the traditional gate-driven design to become 3.2 kV with the proposed substrate-triggered design.

Substrate-triggered SCR device for on-chip ESD protection in fully silicided sub-0.25-μm CMOS process

The turn-on mechanism of a silicon-controlled rectifier (SCR) device is essentially a current triggering event. While a current is applied to the base or substrate of the SCR device, it can be quickly triggered into its latching state. In this paper, a novel design concept to turn on the SCR device by applying the substrate-triggered technique is first proposed for effective on-chip electrostatic discharge (ESD) protection. This novel substrate-triggered SCR device has the advantages of controllable switching voltage and adjustable holding voltage and is compatible with general CMOS processes without extra process modification such as the silicide-blocking mask and ESD implantation. Moreover, the substrate-triggered SCR devices can be stacked in ESD protection circuits to avoid the transient-induced latch-up issue. The turn-on time of the proposed substrate-triggered SCR devices can be reduced from 27.4 to 7.8 ns by the substrate-triggering technique. The substrate-triggered SCR device with a small active area of only 20 /spl mu/m /spl times/ 20 /spl mu/m can sustain the HBM ESD stress of 6.5 kV in a fully silicided 0.25-/spl mu/m CMOS process.

Substrate-triggered ESD protection circuit without extra process modification

A substrate-triggered technique is proposed to improve electrostatic discharge (ESD) protection efficiency of ESD protection circuits without extra salicide blocking and ESD-implantation process modifications in a salicided shallow-trench-isolation CMOS process. By using the layout technique, the whole ESD protection circuit can be merged into a compact device structure to enhance the substrate-triggered efficiency. This substrate-triggered design can increase ESD robustness and reduce the trigger voltage of the ESD protection device. This substrate-triggered ESD protection circuit with a field oxide device of channel width of 150 μm can sustain a human-body-model ESD level of 3250 V without any extra process modification. Comparing to the traditional ESD protection design of gate-grounded nMOS (ggnMOS) with silicide-blocking process modification in a 0.25-μm salicided CMOS process, the proposed substrate-triggered design without extra process modification can improve ESD robustness per unit silicon area from the original 1.2 V/μm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> of ggnMOS to 1.73 V/μm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> .

ESD protection design for CMOS RF integrated circuits using polysilicon diodes

ESD protection design for CMOS RF integrated circuits is proposed in this paper by using the stacked polysilicon diodes as the input ESD protection devices to reduce the total input capacitance and to avoid the noise coupling from the common substrate. The ESD level of the stacked polysilicon diodes on the I/O pad is restored by using the turn-on efficient power-rail ESD clamp circuit, which is constructed by substrate-triggered technique. This polysilicon diode is fully process compatible to general sub-quarter-micron CMOS processes.

Substrate-triggered ESD clamp devices for use in power-rail ESD clamp circuits

New electrostatic discharge (ESD) clamp devices for using in power-rail ESD clamp circuits with the substrate-triggered technique are proposed to improve ESD level in a limited silicon area. The parasitic n–p–n and p–n–p bipolar junction transistors (BJTs) in the CMOS devices are used to form the substrate-triggered devices for ESD protection. Four substrate-triggered devices are proposed and investigated in this work, which are named as the substrate-triggered lateral BJT, the substrate-triggered vertical BJT, the substrate-triggered double BJT, and the double-triggered double BJT. An RC-based ESD-detection circuit is used to generate the triggering current to turn on the proposed substrate-triggered devices. In order to trigger on the parasitic bipolar transistors more effectively, the symmetric multiple-cell square-type layout method is used to realize these substrate-triggered devices. The power-rail ESD clamp circuits with such substrate-triggered devices have been fabricated in a 0.6-μm CMOS process. Experimental results have shown that the substrate-triggered device with double-BJT structure can provide 200% higher ESD robustness in per silicon area, as compared to the NMOS with the traditional gate-driven design.