Strain-shielding Effect Research Articles

The silicone metacarpophalangeal joint arthroplasty: An in-vitro analysis

BackgroundSilicone is still the gold standard implant in metacarpophalangeal arthroplasty. Whereas the clinical results are acceptable, in follow-ups with >10 years, high rates of implant fracture are common, and 5 to 7% of implants required revision. This work's purpose is to analyse the hypothesis that the joint flexion amplitude has a relevant effect on bone strain level, implant stress and bone-implant micromotion, which can reflect an increase in the risk of bone resorption/fatigue failure, implant fracture and osteolysis. MethodsTo experimentally predict the cortical loading behaviour, composite metacarpals and proximal phalanges were used in intact and implanted states. A finite element model was developed to evaluate the structural behaviour of cancellous bone and implant. This model was validated by comparing cortical strain and load–displacement curve with experimental measurements. FindingsBone strain changes between the intact and the implanted states showed a load transfer effect from the cortical to the cancellous bone that increases significantly with the flexion's amplitude rise. The peak implant stress occurred in the flexion amplitudes further away from the implant neutral angle. The highest implant pistoning motion and the highest phalanx cancellous-bone strain occurred simultaneously at the maximum flexion amplitude. InterpretationLimiting joint flexion range will be helpful to reduce the strain-shielding effect on cortical bone, minimizing the overload effect on cancellous bone and decreasing the stress levels and the pistoning motion on the implant, ultimately contributing to the longevity of silicone arthroplasty.

Femoral revision knee Arthroplasty with Metaphyseal sleeves: the use of a stem is not mandatory of a structural point of view

PurposeAlthough metaphyseal sleeves are usually used with stems, little is known about the exact contribution/need of the stem for the initial sleeve-bone interface stability, particularly in the femur, if the intramedullary canal is deformed or bowed. The aim of the present study is (1) to determine the contribution of the diaphyseal-stem on sleeve-femur interface stability and (2) to determine experimentally the strain shielding effect on the metaphyseal femur with and without diaphyseal-stem. It is hypothesised that diaphyseal-stem addition increases the sleeve-femur interface stability and the strain-shielding effect on the metaphyseal femur relatively to the stemless condition.Material and methodsThe study was developed through a combined experimental and finite-element analysis approach. Five synthetic femurs were used to measure cortex strain (triaxial-rosette-gages) behaviour and implant cortex micromotions (Digital Image Correlation) for three techniques: only femoral-component, stemless-sleeve and stemmed-sleeve. Paired t-tests were performed to evaluate the statistical significance of the difference of cortex strains and micromotions. Finite-element models were developed to assess the cancellous bone strain behaviour and sleeve-bone interface micromotions; these models were validated against the measurements.ResultsCortex strains are significantly reduced (p < 0.05) on the stemmed-sleeve with a 150 μstrain mean reduction at the medial and lateral distal sides which compares with a 60 μstrain mean reduction (p > 0.05) on the stemless condition. Both techniques presented a mean cancellous bone strain reduction of 700 μstrain (50%) at the distal region and a mean increase of 2500 μstrain (4x) at the sleeve proximal region relative to the model only with the femoral component. Both techniques presented sleeve-bone micromotions amplitude below 50-150 μm, suitable for bone ingrowth.ConclusionsThe use of a supplemental diaphyseal-stem potentiates the risk of cortex bone resorption as compared to the stemless-sleeve condition; however, the stem is not essential for the enhancement of the initial sleeve-bone stability and has minor effect on the cancellous bone strain behaviour. Based on a purely structural point view, it appears that the use of a diaphyseal-femoral-stem with the metaphyseal sleeve is not mandatory in the revision TKA, which is particularly relevant in cases where the use of stems is impracticable.

Biomechanical analysis of metacarpophalangeal joint arthroplasty with metal-polyethylene implant: An in-vitro study

BackgroundThe most common implant options for the metacarpophalangeal joint arthroplasty include silicone, pyrocarbon and metal-polyethylene. A systematic review of outcomes of silicone and pyrocarbon implants was conducted; however, a similar exercise for metal-polyethylene implants revealed a scarcity of published results and lack of long-term follow-up studies. The aim of the present work is to test the hypothesis that the magnitude of metacarpophalangeal joint cyclic loads generates stress and strain behaviour, which leads to long-term reduced risk of metal-polyethylene component loosening. MethodsThis study was performed using synthetic metacarpals and proximal phalanges to experimentally predict the cortex strain behaviour for both intact and implanted states. Finite element models were developed to assess the structural behaviour of cancellous-bone and metal-polyethylene components; these models were validated by comparing cortex strains predictions against the measurements. FindingsCortex strains in the implanted metacarpophalangeal joint presented a significant reduction in relation to the intact joint; the exception was the dorsal side of the phalanx, which presents a significant strain increase. Cancellous-bone at proximal dorsal region of phalanx reveals a three to fourfold strain increase as compared to the intact condition.InterpretationThe use of metal-polyethylene implant changes the strain behaviour of the metacarpophalangeal joint yielding the risk of cancellous-bone fatigue failure due to overload in proximal phalanx; this risk is more important than the risk of bone-resorption due to the strain-shielding effect. By limiting the loads magnitude over the joint after arthroplasty, it may contribute to the prevention of implant loosening.

Ex-vivo and in vitro validation of an innovative mandibular condyle implant concept

PurposeThe purpose of this study is to pre-validate an inovative implant concept, and to compare the behavior of the mandibular condyle against a commercial Biomet implant in an ex vivo model and present results of the first cadaveric studies. Materials and methodsThree experimental cadaveric condyles were tested under three conditions: one intact, another with the Biomet model, and one with the innovative concept. The condyle was tested with a reaction of 300 N in all situations and the principal strains were measured. Before the geometry of the cadaveric condyle was reconstructed from a microCT scan, and a finite element model was created. Finally, a procedure was carried out with the new implant by two expert surgeons on a two cadaveric head model. ResultsIn vitro the mandible condyle presents a linear behavior until maximum load. The strain measured with Biomet implant indicates a strain shielding effect in the proximal region, inducing bone loss in the long term. The lingual side of the Biomet implanted condyle presents an increase of +44% in strain. ConclusionThe new concept was evaluated and showed a similar behavior to the intact model, and better behavior than the Biomet. The innovative concept proves that it is possible to avoid screws for a TMJ fixation and improve the TMJ alloplastic behavior.

Biomechanical evaluation of pyrocarbon proximal interphalangeal joint arthroplasty: An in-vitro analysis

BackgroundPyrocarbon proximal interphalangeal joint arthroplasty provided patients with excellent pain relief and joint motion, however, overall implant complications have been very variable, with some good outcomes at short-medium-term follow-up and some bad outcomes at longer-term follow-up. Implant loosening with migration, dislocation and implant fracture were the main reported clinical complications. The aim of the present work was to test the hypothesis that the magnitude proximal interphalangeal joint cyclic loads in daily hand functions generates stress-strain behaviour which may be associated with a risk of pyrocarbon component loosening in the long-term. MethodsThis study was performed using synthetic proximal and middle phalanges to experimentally predict the cortex strain behaviour and implant stability considering different load conditions for both intact and implanted states. Finite element models were developed to assess the structural behaviour of cancellous-bone and pyrocarbon components, these models were validated against experimentally measured cortex strains. FindingsCortex strains showed a significant increase at dorsal side and reduction at palmar side between intact and implanted states. Cancellous-bone adjacent to the condylar implant base components suffers a two to threefold strain increase, comparing with the intact condition. InterpretationThe use of pyrocarbon implant changes the biomechanical behaviour of the joint phalanges and is associated with a potential risk of support cancellous-bone suffer fatigue failure in mid to long term due to the strain increase for cyclic loads in the range of daily hand activities, this risk is more prominent than the risk of bone resorption due to strain-shielding effect.

Experimental and numerical predictions of Biomet(®) alloplastic implant in a cadaveric mandibular ramus.

The purpose of this study was to evaluate experimentally the behaviors of an intact and an implanted cadaveric ramus, to compare and analyze load mechanism transfers between two validated finite element models. The intact, clean cadaveric ramus was instrumented with four rosettes and loaded with the temporal reaction load. Next, the Biomet microfixation implant was fixed to the same cadaveric mandibular ramus after resection. The mandibular ramus was reconstructed from computed tomographic images, and two finite element models were developed. The experimental results for the mandibular ramus present a linear behavior of up to 300N load in the condyle, with the Biomet implant influencing strain distribution; the maximum influence was near the implant (rosette #4) and approximately 59%. The experimental and numerical results present a good correlation, with the best correlation in the intact ramus condition, where R(2) reaches 0.935 and the slope of the regression line is 1.045. The numerical results show that screw #1 is the most critical, with maximum principal strains in the bone around 21,000με, indicating possible bone fatigue and fracture. The experimental results show that the Biomet temporomandibular joint mandibular ramus implant changes the load transfer in the ramus, compared to the intact ramus, with its strain-shielding effect. The numerical results demonstrate that only three screws are important for the Biomet TMJ fixation. These results indicate that including two proximal screws should reduce stresses in the first screws and strains in the bone.

Strain shielding from mechanically activated covalent bond formation during nanoindentation of graphene delays the onset of failure.

Mechanical failure of an ideal crystal is dictated either by an elastic instability or a soft-mode instability. Previous interpretations of nanoindentation experiments on suspended graphene sheets,1,2 however, indicate an anomaly: the inferred strain in the graphene sheet directly beneath the diamond indenter at the measured failure load is anomalously large compared to the fracture strains predicted by both soft-mode and acoustic analyses. Through multiscale modeling combining the results of continuum, atomistic, and quantum calculations, and analysis of experiments, we identify a strain-shielding effect initiated by mechanochemical interactions at the graphene-indenter interface as the operative mechanism responsible for this anomaly. Transmission electron micrographs and a molecular model of the diamond indenter's tip suggest that the tip surface contains facets comprising crystallographic {111} and {100} planes. Ab initio and molecular dynamics (MD) simulations confirm that a covalent bond (weld) formation between graphene and the crystallographic {111} and {100} facets on the indenter's surface can be induced by compressive contact stresses of the order achieved in nanoindentation tests. Finite element analysis (FEA) and MD simulations of nanoindentation reveal that the shear stiction provided by the induced covalent bonding restricts relative slip of the graphene sheet at its contact with the indenter, thus initiating a local strain-shielding effect. As a result, subsequent to stress-induced bonding at the graphene-indenter interface, the spatial variation of continuing incremental strain is substantially redistributed, locally shielding the region directly beneath the indenter by limiting the buildup of strain while imparting deformation to the surrounding regions. The extent of strain shielding is governed by the strength of the shear stiction, which depends upon the level of hydrogen saturation at the indenter's surface. We show that at intermediate levels of hydrogen saturation the strain-shielding effect can enable the graphene to support experimentally determined fracture loads and displacements without prematurely reaching locally limiting states of stress and deformation.

Anisotropic bone remodeling of a biomimetic metal-on-metal hip resurfacing implant

Hip resurfacing (HR) is a highly attractive option for young and active patients. Some surgeons have advocated cementing the metaphyseal stem of the femoral component to improve fixation and survivorship of HR. However, extending component fixation to the metaphysis may promote femoral head strain shielding, which in turn may reduce survival of the femoral component. Replacing the metallic metaphyseal stem by a composite material with bone-matching properties could help to alleviate this phenomenon. This study uses finite element analysis to examine the strain state in the femoral head for three types of implant fixation: an unfixed metallic stem, an osseointegrated biomimetic stem and a cemented metallic stem. Bone remodeling is also simulated to evaluate long-term bone resorption due to strain shielding. Results show that the unfixed stem causes strain shielding in the femoral head, and that cementing the stem increases strain shielding. The biomimetic stem does not eliminate the strain shielding effect, but reduces it significantly versus the metallic cemented version. The current finite element study suggests that an osseointegrated metaphyseal stem made of biomimetic material in hip resurfacing implants could become an interesting alternative when fixation extension is desired.

Medial versus Lateral Supraspinatus Tendon Properties

Background Rotator cuff repair retear rates range from 25% to 90%, necessitating methods to improve repair strength. Although numerous laboratory studies have compared single-row with double-row fixation properties, little is known regarding regional (ie, medial vs lateral) suture retention properties in intact and torn tendons. Hypothesis A torn supraspinatus tendon will have reduced suture retention properties on the lateral aspect of the tendon compared with the more medial musculotendinous junction. Study Design Controlled laboratory study. Methods Human supraspinatus tendons (torn and intact) were randomly assigned for suture retention mechanical testing, ultrastructural collagen fibril analysis, or histologic testing after suture pullout testing. For biomechanical evaluation, sutures were placed either at the musculotendinous junction (medial) or 10 mm from the free margin (lateral), and tendons were elongated to failure. Collagen fibril assessments were performed using transmission electron microscopy. Results Intact tendons showed no regional differences with respect to suture retention properties. In contrast, among torn tendons, the medial region exhibited significantly higher stiffness and work values relative to the lateral region. For the lateral region, work to 10-mm displacement (1592 ± 261 N-mm) and maximum load (265 ± 44 N) for intact tendons were significantly higher (P < .05) than that of torn tendons (1086 ± 388 N-mm and 177 ± 71 N, respectively). For medial suture placement, maximum load, stiffness, and work of intact and torn tendons were similar (P >. 05). Regression analyses for the intact and torn groups revealed generally low correlations between donor age and the 3 biomechanical indices. For both intact and torn tendons, the mean fibril diameter and area density were greater in the medial region relative to the lateral (P ≤. 05). In the lateral tendon, but not the medial region, torn specimens showed a significantly lower fibril area fraction (48.3% ± 3.8%) than intact specimens (56.7% ± 3.6%, P < .05). Conclusion Superior pullout resistance of medially placed sutures may provide a strain shielding effect for the lateral row after double-row repair. Larger diameter collagen fibrils as well as greater fibril area fraction in the medial supraspinatus tendon may provide greater resistance to suture migration. Clinical Relevance While clinical factors such as musculotendinous integrity warrant strong consideration for surgical decision making, the present ultrastructural and biomechanical results appear to provide a scientific rationale for double-row rotator cuff repair where sutures are placed more medially at the muscle-tendon junction.

Strain shielding in distal femur after patellofemoral arthroplasty under different activity conditions

Strain shielding, a mechanical effect occurring in structures combining stiff with more flexible materials, is considered to lead to a reduction of density in bone surrounding the implant. This effect can be related to the weakness of the implant fixation, which can promote implant loosening. Several studies describe a significant decrease in postoperative bone mineral density adjacent to joint implants, which can compromise their long-term fixation. The aim of the present study was to quantify the strain shielding effect on the distal femur after patellofemoral arthroplasty. For this purpose three activities of daily living were considered: level walking, stair climbing and deep bending at different angles of knee flexion. To determine the strain shielding effect, cortical bone strains were measured experimentally with triaxial strain gauges in synthetic femurs before and after patellofemoral arthroplasty for each of the different daily activities. The results showed that the patellofemoral arthroplasty in general reduced the strains in the medial and distal regions of the femur when deep bending activity occurred, consequently, strain shielding in these regions, with strain decreases of −72.0% and −67.5% were measured. On the other side, higher values of strain were found in the anterior region after patellofemoral replacement for this activity with an increase of +182.0%. The occurrence of strain shielding seems to be more significant when the angle of knee flexion and applied load increases. Strain shielding and over-loading may have relevant effects on bone remodeling surrounding the patellofemoral implant, suggesting a potential effect of later bone resorption in the medial and distal femur regions in case of regular deep bending activity.

Strain shielding in proximal tibia of stemmed knee prosthesis: Experimental study

Theoretical concerns about the use of cemented or press-fit stems in revision total knee arthroplasty (TKA) include stress shielding with adverse effects on prosthesis fixation. Revision TKA components are commonly stemmed to protect the limited autogenous bone stock remaining. Revision procedures with the use of stems can place abnormal stresses through even normal bone by their constrained design, type of materials and fixation method and may contribute for bone loss. Experimental quantification of strain shielding in the proximal synthetic tibia following TKA is the main purpose of the present study. In this study, cortical bone strains were measured experimentally with tri-axial strain gauges in synthetic tibias before and after in vitro knee surgery. Three tibias were implanted with cemented and press-fit stem augments and solely with a tibial tray (short monobloc stem) of the P.F.C. Sigma Modular Knee System. The difference between principal strains of the implanted and the intact tibia was calculated for each strain gauge position. The results demonstrated a pronounced strain-shielding effect in the proximal level, close to tibial tray with the cemented stem augment. The press-fit stem presented a minor effect of strain shielding but was more extensively throughout the stem. An increase of strains closely to the distal tip of the cemented and the press-fit stem augment was observed. This suggests for a physiological condition, a potential effect of bone resorption at the proximal region for the cemented stem augment. The localized increase of strains in stems tip can be related with the clinical finding of the pain, at the end of stem after revision TKA.

Functional Knee Brace Alters Predicted Knee Muscle and Joint Forces in People with ACL Reconstruction during Walking

Functional knee braces used during rehabilitation from injury and surgery to the anterior cruciate ligament (ACL) have been reported to provide a strain-shielding effect on the ACL in healthy people while standing, reduce quadriceps electromyoraphy in ACL-deficient individuals, and alter joint torque patterns in people with ACL reconstruction during walking. These results led to the hypothesis that functional knee braces protect a reconstructed ACL during dynamic activity by reducing the anterior shear load applied to the knee. This hypothesis was tested by investigating the effects of a functional knee brace on lower extremity muscle forces and the anteroposterior shear force at the knee joint during the stance phase of walking in people with ACL reconstruction. Ground reactions and sagittal plane video were recorded from 9 ACL-reconstructed individuals as they walked with and without a functional knee brace, and from 10 healthy people without the functional knee brace. Inverse dynamics were used to calculate the net joint torques in the lower extremity during the stance phase. Hamstrings, quadriceps, and gastrocnemius muscle and knee anteroposterior shear force were then predicted with a sagittal-plane mathematical model. Compared to healthy individuals, those with ACL reconstruction walked with 78% more hamstrings impulse and 19% less quadriceps impulse (bothp&lt; .05). The functional knee brace produced an additional 43% increase in hamstrings impulse and an additional 13% decrease in quadriceps impulse in the ACL group. Peak anterior knee shear force and anterior impulse were 41% lower and 16% lower in ACL vs. healthy individuals, respectively. The functional knee brace further reduced the peak knee shear force and impulse 28% and 19%, respectively, in the ACL group. It was concluded that a functional knee brace protects a reconstructed ACL during walking by altering muscle forces and reducing the anterior shear force applied to the knee joint.

Anterior cruciate ligament strain in-vivo: A review of previous work

Disruption of the anterior cruciate ligament (ACL), a primary stabilizer of the knee, can produce disability. The purpose of our work has been to study the normal ACL in humans, in the presence of normal muscle function and body weight, and develop clinical criteria for reconstruction, establish a basis for rehabilitation programs, and evaluate how knee braces protect this important ligament. The strain behavior of the ACL has been measured by arthroscopic implantation of the Differential Variable Reluctance Transducer while subjects are under local anesthesia. Movement of the knee from a flexed to an extended position, either passively or through contraction of the leg muscles, produces an increase in ACL strain values. Isolated contraction of the dominant quadriceps with the knee between 50° and extension creates substantial increases in strain. In contrast, isolated contraction of the hamstrings at any knee position does not increase strain. With the knee un-weighted, the protective strain shielding effect of a functional knee brace decreases as the magnitude of anterior shear load applied to the tibia increases. A different behavior occurs during weight bearing, the strain shielding effect of the brace remains constant as the magnitude of anterior load increases. Our approach is novel in that it can be used to measure on important portion of the ACLs strain distribution while clinically relevant loads are applied to the knee, subjects perform rehabilitation exercises, or in the presence of different orthoses such as functional knee braces.

Anterior cruciate ligament injury rehabilitation in athletes. Biomechanical considerations.

Postoperative rehabilitation is a major factor in the success of an anterior cruciate ligament (ACL) reconstruction procedure. Clinical investigations of patients after ACL reconstruction have shown that immobilisation of the knee, or restricted motion without muscle contraction, leads to undesired outcomes for the articular, ligamentous, and musculature structures that surround the knee. Early joint motion is beneficial for; reducing pain, capsular contractions, articular cartilage, and for minimising scar formation that limit joint motion. These findings, combined with graft materials that have biomechanical properties similar to the normal ACL, and adequate fixation strength, have led many to recommend aggressive rehabilitation programmes that involve contraction of the dominant quadriceps muscles. Recently, a prospective, randomised study of rehabilitation following ACL reconstruction has presented evidence that a closed kinetic chain exercise programme (foot fixed against a resistance) results in anterior-posterior knee laxity values that are similar to the contralateral normal knee. Also, open kinetic chain exercises (foot not fixed against a resistance) result in increased anterior-posterior knee laxity compared with the normal knee. Criteria must be observed because the relationship between rehabilitation exercises and the healing response of an ACL graft is unknown at present. Biomechanical studies of healing ACL grafts performed in animals have shown that the graft requires a long time to revascularise and heal, and that the biomechanical behaviour of the graft never returns to normal. Functional knee braces provide a protective strain-shielding effect on the ACL when anterior shear loads and internal torques are applied to the knee in the non-weight-bearing condition. However, the strain shielding effect of functional braces decrease as the magnitude of anterior shear and internal torque applied to the knee increase. Future studies should strive to determine the actual loads transmitted across the knee and ACL graft strain during various rehabilitation exercises and relate these to the healing response of the knee and graft.

The effect of functional knee-braces on strain on the anterior cruciate ligament in vivo.

Functional knee-braces are widely used to protect injured or reconstructed anterior cruciate ligaments, despite the fact that few scientific data support their efficacy. We studied seven functional braces, representative of both the typical custom-fit and off-the-shelf designs. The braces were tested on subjects who had a normal anterior cruciate ligament and were scheduled for arthroscopic meniscectomy or exploration of the knee under local anesthesia. After the operative procedure, a Hall-effect strain-transducer was applied to the anterior cruciate ligament. Under low anterior shear loads, two braces provided some protective strain-shielding effect compared with no brace, but this strain-shielding effect did not occur at the higher anterior shear loads expected during the high-stress activities common to athletic events. The DonJoy, Townsend, C.Ti., and Lenox Hill braces demonstrated a strain-shielding effect on the anterior cruciate ligament with an internal torque of five newton-meters applied to the tibia. None of the braces had any effect on strain on the anterior cruciate ligament during active range of motion of the knee from 10 to 120 degrees or during isometric contraction of the quadriceps. Wearing of a brace did not produce an increase in the value for strain on the anterior cruciate ligament. For the activities that were evaluated in this study, none of the braces produced adverse effects on the anterior cruciate ligament, and there were no significant differences in the strain on the anterior cruciate ligament between the use of a custom-fit or an off-the-shelf brace design. There were no apparent advantages of the more expensive custom-made braces compared with the off-the-shelf designs.