Straightforward Design Research Articles

Design optimization of integral stiffeners for 3D woven composite preforms

Although 3D orthogonal textile woven composite panels demonstrate good impact damage resistance, they often have relatively low bending stiffness. Typically, stiffeners are added to improve the bending resistance through fabrication processes such as sewing and panel/flange joining through matrix adhesion. These secondary processes can be undesirable, adding expense and potential weak points to the structure. Inspired by bio-structures such as peanut shells with surface ridges and graded through-thickness densities, we seek to develop embedded stiffeners for 3D orthogonal textile woven composite panels at sub-component scale to enhance the bending stiffness. Such stiffened textile architecture can be integrally fabricated in an orthogonal loom using standard weaving methods and provides a balance between improving structural bending stiffness and the manufacturing cost and maintaining good impact damage resistance. Utilizing a manufacturing-based parameterization method, a low-fidelity evaluation tool based on the iso-strain method is developed and a straightforward design methodology is proposed to implement these novel composite structures. Numerical design optimization examples are demonstrated.

Broadband thulium fiber amplifier for spectral region located beyond the L-band

We present the development of a pair of silica-based thulium-doped fiber amplifiers working together in a broad spectral range from 1.65 µm to 2.02 µm. For the one optimized for shorter wavelengths, we designed and prepared optical fiber with a depressed cladding. We show the performance of the amplifiers achieving small-signal gain of at least 10 dB over 350 nm range from 1670 nm to 2020 nm, maximum gain of 40.7 dB with a noise figure as low as 6.45 dB and an optical signal-to-noise ratio of up to 50 dB. To the best of our knowledge, it is the first time that thulium fiber amplifiers of straightforward design without using redundant spectral filters operating efficiently in such a wide spectral region are demonstrated.

Augmented reality display with high eyebox uniformity over the full field of view based on a random mask grating

Ensuring uniform illuminance in waveguide-based augmented reality (AR) display devices is crucial for providing an immersive and comfortable visual experience. However, there is a lack of a straightforward and efficient design method available to achieve illuminance uniformity over the full field of view. To address this issue, we propose a novel design that utilizes random mask gratings (RMGs) as the folding grating and the out-coupling grating. Unlike traditional approaches that modify the grating structure, we control the diffraction efficiency distribution by adjusting the filling factor of the mask while keeping the grating structure unchanged in one RMG. The grating structures are designed and optimized based on rigorous coupled wave analysis and particle swarm optimization. The feasibility of our method is verified by the simulation results in Lighttools. In the FOV range of 20°×15°, the eyebox uniformities of all fields are greater than 0.78, which can provide a good visual experience for users.

Towards Advancing Translators’ Guidance for Organisations Tackling Innovation Challenges in Manufacturing within an Industry 5.0 Context

Following the vision of the European Commission, organisations and workers establishing Industry 5.0 approaches aspire to more future-proof, resilient, sustainable, and human-centred European industries. In this contribution, we explore how technological innovations that contribute to a “win–win” interaction with involved stakeholders may be advanced in a human-centred and transparent proceeding supported by impartial expert translators who provide information or knowledge-based guidance for decision-makers, initiators and implementers in manufacturing innovation driven by sustainability. We elaborate a stepwise procedure for agreeing on milestones and conjointly treading the path towards solving innovation challenges during a translation process. We exemplify the technological aspects of such a process using an innovation case aiming at identifying parameters for enhancements in a vacuum-bagging process applied to the manufacturing of composite parts from prepregs based on condensation-curing matrix resins made from renewable resources. In detail, we present a straightforward design of an experimental approach varying the dwelling temperature and the temperature ramps during the curing of stacked prepregs. In this way, we demonstrate that for cured composites comprising a poly(furfuryl alcohol)-based matrix, the porosity and connected mechanical properties achieved with autoclave-free curing processes sensitively depend on these process parameters. Applying the resulting data-based model is shown to support decision-making for sustainable composite manufacture.

Multi-objective design optimization of electromagnetic coil for effective actuation of magnetic endocapsule devices

Magnetic actuation with cylindrical electromagnetic coils is an upcoming technology due to its straightforward design and adaptability for magnetic endocapsule control in the gastrointestinal tract. This paper presents a mathematical model for characterizing the magnetic field generated by cylindrical electromagnetic coils and optimizing design parameters tailored for a typical 6.50-gram magnetic endocapsule. This paper adopted a dual-set parallel cylindrical electromagnetic coil configuration. The cylindrical electromagnetic coil design was conceptualized as a multi-objective optimization problem, which concerns geometrical parameters and copper winding usage, resolved through the amalgamation of a genetic algorithm and a Pareto optimal methodology. The optimal design produces an actuation force of 132.20 mN for a 6.50-gram magnetic endocapsule, and the results are validated with finite element simulations. The adopted and optimized system configuration has a average motion resolution of 2.7 mm and an average motion velocity of 162 mm/min.

Free spectral range measurement based on a multi-longitudinal mode laser self-mixing ellipse fitting degree detection technique.

A method by detecting the ellipse fitting degree of the trajectory equation formed by two self-mixing (SM) signals in the multi-longitudinal mode laser SM system with a Wollaston prism is presented to test the free spectral range (FSR) of the laser. By utilizing the orthogonal vector and phase-shift characteristics between adjacent longitudinal modes, the fluctuations in multi-mode SM effects caused by changes in the external cavity length are transformed into alterations in the trajectory composed of two orthogonal SM signals. The FSR is calculated by detecting the difference in external cavity lengths between the two positions, where the trajectory of the two SM signals best fits an ellipse. To achieve an automatic FSR measurement, the ellipse fitting degree is proposed as the criterion for positioning the external cavity mode. Experimental results indicate that the FSR of the laser diode is measured to be 85.23 GHz with a resolution of 0.48 GHz, while the corresponding external cavity resolution is 10 µm, and the resolution of the ellipse fitting degree is less than 1. The compact and straightforward design, coupled with high sensitivity, automated measurements, and immunity to optical feedback, holds significant promise as a robust tool for measuring FSR and assessing laser performance.

Design of a symmetry-broken tetrahedral protein cage by a method of internal steric occlusion.

Methods in protein design have made it possible to create large and complex, self-assembling protein cages with diverse applications. These have largely been based on highly symmetric forms exemplified by the Platonic solids. Prospective applications of protein cages would be expanded by strategies for breaking the designed symmetry, for example, so that only one or a few (instead of many) copies of an exterior domain or motif might be displayed on their surfaces. Here we demonstrate a straightforward design approach for creating symmetry-broken protein cages able to display singular copies of outward-facing domains. We modify the subunit of an otherwise symmetric protein cage through fusion to a small inward-facing domain, only one copy of which can be accommodated in the cage interior. Using biochemical methods and native mass spectrometry, we show that co-expression of the original subunit and the modified subunit, which is further fused to an outward-facing anti-GFP DARPin domain, leads to self-assembly of a protein cage presenting just one copy of the DARPin protein on its exterior. This strategy of designed occlusion provides a facile route for creating new types of protein cages with unique properties.

Determination of pullout capacity for an inclined single-plate helical pile under combined loading in clay

Although helical piles are frequently installed at an angle to the vertical, there has been limited investigation into how this inclination affects the pile’s ability to resist pullout forces. This paper utilizes numerical analysis to examine the pullout capacities and failure envelopes of inclined helical piles under combined loading. Through the application of the coupled Eulerian-Lagrangian finite element analysis, the impact of load inclination and azimuth angle of the pullout plane on the ultimate holding capacity of inclined helical piles was assessed. It was found that the pullout plane that is in the opposite direction to the helical pile inclination is the most crucial. The parametric study showed that the crucial failure envelope is primarily influenced by the helical pile inclination angle, embedment depth ratio, helix diameter ratio, and normalized soil strength ratio. Several tables were provided, which contain fitting constants suitable for a range of helical pile inclination angles, embedment depth, helix diameter ratio, and normalized soil strength ratios. Based on these results, a straightforward design procedure was established to evaluate the holding capacity of an inclined installed helical pile. The research results are expected to assist engineers in accounting for helical pile inclination during the design phase.

Abstract 6082: Rapid on-site nucleic acid detection using CRISPR and digital signal processing for portable and integrated cervical cancer screening in low resource settings

Abstract Addressing the global disparity in cancer care necessitates the development of rapid and affordable nucleic acid (NA) testing technologies. This need is particularly critical for cervical cancer. Molecular detection of human papillomavirus (HPV) has emerged as a highly accurate screening method, surpassing traditional Pap smears. However, implementing this transition in low- and middle-income countries has been challenging due to the high costs and centralized facilities required for current NA tests. Here, we present CreDiT (CRISPR Enhanced Digital Testing), an advanced diagnostic system for rapid, on-site NA detection. CreDiT integrates two major technical breakthroughs: i) a one-pot CRISPR strategy that simultaneously amplifies both target NAs and analytical signals, and ii) a robust fluorescent detection method based on digital communication (encoding/decoding) technology. These innovations enhance CreDiT's practical utility, offering a rapid assay (<35 minutes) that integrates NA extraction and detection in a single streamlined workflow. Furthermore, CreDiT's straightforward probe design enables easy incorporation of new NA targets, while its compact device provides robust signal detection. We adapted CreDiT for point-of-care HPV screening by designing probes for high-risk HPV genes (HPV16, HPV18, HPV45, HPV31, HPV33, HPV58) and oncoprotein mRNAs (E6, E7, p16INK4a) and developing a portable CreDiT device capable of processing 12 samples. CreDiT demonstrated sensitive detection of cell-derived HPV DNA targets down to single copies and accurately identified HPV types in every clinical cervical brushing specimen (n = 121) we tested. This technology has the potential to facilitate prompt and reliable triaging of high-risk HPV, overcoming pathology bottlenecks and circumventing geographical and socioeconomic barriers to effective cervical cancer screening in resource-limited regions. This work has spearheaded recent screening research efforts in Uganda and Ghana. Citation Format: Chang Yeol Lee, Hyunho Kim, Hanna Lee, Thomas Randall, Amy Ly, Hakho Lee, Cesar M. Castro. Rapid on-site nucleic acid detection using CRISPR and digital signal processing for portable and integrated cervical cancer screening in low resource settings [abstract]. In: Proceedings of the American Association for Cancer Research Annual Meeting 2024; Part 1 (Regular Abstracts); 2024 Apr 5-10; San Diego, CA. Philadelphia (PA): AACR; Cancer Res 2024;84(6_Suppl):Abstract nr 6082.

Hydrogels Based on Chitosan and Nanoparticles and Their Suitability for Dyes Adsorption from Aqueous Media: Assessment of the Last-Decade Progresses.

Water is one of the fundamental resources for the existence of humans and the environment. Throughout time, due to urbanization, expanding population, increased agricultural production, and intense industrialization, significant pollution with persistent contaminants has been noted, placing the water quality in danger. As a consequence, different procedures and various technologies have been tested and used in order to ensure that water sources are safe for use. The adsorption process is often considered for wastewater treatment due to its straightforward design, low investment cost, availability, avoidance of additional chemicals, lack of undesirable byproducts, and demonstrated significant efficacious potential for treating and eliminating organic contaminants. To accomplish its application, the need to develop innovative materials has become an essential goal. In this context, an overview of recent advances in hydrogels based on chitosan and nanocomposites and their application for the depollution of wastewater contaminated with dyes is reported herein. The present review focuses on (i) the challenges raised by the synthesis process and characterization of the different hydrogels; (ii) the discussion of the impact of the main parameters affecting the adsorption process; (iii) the understanding of the adsorption isotherms, kinetics, and thermodynamic behavior; and (iv) the examination of the possibility of recycling and reusing the hydrogels.

A highly sensitive Lock-Cas12a biosensor for detection and imaging of miRNA-21 in breast cancer cells

The expression levels of microRNA (miRNA) vary significantly in correlation with the occurrence and progression of cancer, making them valuable biomarkers for cancer diagnosis. However, their quantitative detection faces challenges due to the high sequence homology, low abundance and small size. In this work, we established a strand displacement amplification (SDA) approach based on miRNA-triggered structural “Lock” nucleic acid (“Lock” DNA), coupled with the CRISPR/Cas12a system, for detecting miRNA-21 in breast cancer cells. The “Lock” DNA freed the CRISPR-derived RNA (crRNA) from the dependence on the target sequence and greatly facilitated the extended detection of different miRNAs. Moreover, the CRISPR/Cas12a system provided excellent amplification ability and specificity. The designed biosensor achieved high sensitivity detection of miRNA-21 with a limit of detection (LOD) of 28.8 aM. In particular, the biosensor could distinguish breast cancer cells from other cancer cells through intracellular imaging. With its straightforward sequence design and ease of use, the Lock-Cas12a biosensor offers significant advantages for cell imaging and early clinical diagnosis.

Seismic performance assessment and design procedure of base-isolated bridges with lead-rubber-bearing and negative stiffness springs (LRB-NS)

This study proposed a straightforward and simplified design procedure for the base-isolated highway bridges with LRB and negative stiffness springs (LRB-NS) device. Compared with the traditional LRB-isolated system, the proposed LRB-NS device contains dual-functionality: (a) alleviate the nonlinearity and damage in piers during slight-to-moderate earthquakes; (b) control the excessive bearing deformation and prevent failure during catastrophic excitations. Therefore, this device effectively improves the post-earthquake function and seismic resilience of bridge systems, and facilitate the rescue operations, since bridge can allow the passage of urgent vehicles with minimal repair. With incremental dynamic analysis (IDA) accounting for the record-to-record variability, the LRB-NS device is shown with dual-functionality as designed and better seismic performance than LRB, subjected to all of far-field (FF), near-fault no-pulse (NFNP), and near-fault pulse-type (NFPT) motions. Additionally, the influence of three kernel parameters, i.e., target period ratio sy_LRB-NS, initial spring length l, and critical deformation ucr, is also investigated in detail, concerning both the structural properties and seismic responses. The results show that increasing sy_LRB-NS and l both benefits the dual-functionality of LRB-NS, but the efficiency reduces with the increase of these design values. While greater ucr significantly reduces column nonlinearity, the bearing deformation is increased as a result, and thus careful tradeoff should be made during practical design.

Enhanced Resolution, Throughput, and Stability of Aerosol Jet Printing via In Line Heating

AbstractAerosol jet printing offers high resolution, broad materials compatibility, and digital patterning for flexible, conformal, and hybrid electronics. However, limited throughput, instability, and complex optimization requirements inhibit translation to industrial applications. An in‐line heater integrated on a custom printer is demonstrated to modulate droplet evaporation in the aerosol phase, thereby decoupling the deposition rate of functional solids and liquid ink to enable taller, narrower features with aspect ratios reaching 0.29 for a single line. Heating the printhead from room temperature to 80 °C reduced the sensitivity of resolution to deposition rate by ≈90%, improving reliability. With this strategy, increasing the linear deposition rate by 10x results in a modest increase of 27% in line width, compared to a four‐fold increase without heating, permitting higher throughput without sacrificing print quality. Providing a control for in‐line drying independent of ink formulation enables rapid, straightforward design of new materials and processes. This ability to engineer drying of droplets prior to impingement provides a versatile tool to meet complex fabrication challenges, as demonstrated here for both high aspect ratio printing and conformal patterning on rough and three‐dimensional surfaces.

Harmonics suppression in high-speed railway via single-phase traction converter with an LCL filter using fuzzy logic control strategy

Introduction. The railway Traction Power Supply System (TPSS) encounters a common challenge related to high-frequency harmonic resonance, especially when employing AC-DC-AC traction drive systems in high-speed trains. This resonance issue arises when the harmonic elements introduced by the traction AC-DC converter on the grid side of trains align with the innate resonance frequency of the TPSS. The novelty the proposed work focuses on the challenges associated with resonance elevation and high-frequency harmonics in high-speed trains, while simultaneously enhancing energy quality. This is achieved by integrating a pulse-width-modulated converter on the grid side with a single-phase configuration and incorporating an LCL filter. Methodology. In order to optimize the system’s efficiency, a robust control system is employed, taking advantage of the capabilities of a fuzzy logic controller (FLC). The choice of the FLC is justified by its straightforward design and reliability, emphasizing the dedication to precise control, as fuzzy logic excels in handling complex, nonlinear systems. Through the use of linguistic variables and heuristic reasoning, the FLC adjusts to dynamic changes in the system, demonstrating its efficacy in enhancing both transient and steady-state responses. Practical value. A grid-side LCL filter-based converter was meticulously designed and rigorously simulated using the MATLAB/Simulink platform. The inclusion of an advanced FLC in the system introduced a novel approach to control strategies, surpassing the traditional PI controller. Through a comprehensive comparative analysis, the simulation results showcased the remarkable efficacy of the proposed solution in an effectively mitigating high-frequency resonance within the TPSS. This outcome underscores the potential of FLC as a sophisticated control mechanism for enhancing the performance systems in railway applications, showcasing its superiority over conventional control methods. The study contributes in shedding light on innovative approaches for optimizing the control and efficiency of grid-side LCL filter-based converters in high-speed train systems.

Simulation Model of Dual Boost Inverter using Half Cycle Modulation Technique

The output voltage of conventional full bridge inverters is lower than the DC input voltage. In applications where the input DC voltage is very low, front-end step-up converters are typically needed, resulting in a two-stage conversion process. The Dual boost inverter (DBI) offers many benefits, including fewer power devices, a straightforward design, and the ability to operate in both boost and buck modes. The traditional modulation technique used in DBI has a number of disadvantages, including the fact that all the devices work at higher frequencies and must tolerate larger voltage and current stresses, which increases conduction and switching losses and lowers efficiency. This study suggests a novel modulation technique called half cycle modulation (HCM), which makes all devices work at high frequency only every half cycle, significantly reducing conduction and switching losses and boosting DBI efficiency. Additionally, an improved DBI is suggested that can bypass the inductor current with little switching stress in order to reduce the current circulation losses in DBI. In this study, a detailed comparison between the traditional DBI and the HCM modulated DBI is discussed. In the MATLAB/SIMULINK software, the suggested DBI and its modulation techniques are simulated, and the results are also shown.

Performance of Soil-bearing Spread Footings Supporting Highway Structures

Background Soil-bearing spread footings (SBSF) are emerging as an increasingly attractive option for supporting highway structures. SBSF offers numerous benefits compared to deep foundations, including cost-effectiveness, accelerated construction, straightforward design, environmentally friendly characteristics, and reduced maintenance requirements. Objective The primary objective of this study is to assess the performance of highway structures that SBSF supports at four specific locations in Ohio. The findings from this assessment will serve as valuable recommendations for the future application of spread footings while identifying potential usage constraints. Methods The project team conducted a comprehensive review of documented performance data, assessed the effectiveness of existing footings, and compared these assessments against established structural performance criteria. Additionally, the team analyzed calculated settlements, provided an estimate of acceptable structural settlement, compared measured settlements with predicted values, and examined the relationship between performance and soil conditions. Results The data gathered, and field assessments conducted at all four sites encompassed in this investigation affirm that SBSF structures function as designed, displaying no signs of settlements or cracks associated with rideability. Both measured and calculated settlements fall within acceptable tolerances. While all structures exhibited acceptable levels of differential settlement, one encountered a differential settlement of approximately 54 mm between substructures, attributed to cohesive soil (A-6) in deeper layers. Conclusion SBSF structures were constructed by the manuals and guidelines established by the Ohio Department of Transportation (ODOT) and exhibited satisfactory performance. This paper also offers recommendations for settlement monitoring methods and plan notes that should be incorporated into the Ohio Department of Transportation's practices.

The nature of PDMS affects the results of the immunoassays carried out in microfluidic channels

Due to various physical or biochemical processes, the nature of polydimethylsiloxane (PDMS) could affect the sensitivity and accuracy of immunoassays performed in microfluidic channels. An appropriate PDMS membrane with high adsorption properties and low background noise allows more sensitive detection of biomarkers. Here, we explored the unusual correlation between membrane surface properties and the signal-to-noise ratio (SNR) of immunoassay, developed a microfluidic-based versatile point-of-care (MVP) detection system on PDMS membrane to simultaneously detect multiple vitamins from multiple human serums. Compared with conventional enzyme-linked immunosorbent assay (ELISA) and Roche electroluminescence method, the MVP detection system exhibits a lower consumption of sample and reagents (10 µL per test), a lower limit of detection (LOD: 6.15 ng/mL), a higher SNR (33.49 dB) and multiplexed ability (seven samples and two targets in one assay). Our MVP detection system can quantitatively detect folic acid (FA) and vitamin D3 (VD3) from human serums and shows good consistency with ELISA and Roche electroluminescence methods. The R square values of FA and VD3 detections are 0.94 and 0.91, respectively. The MVP system is more cost-effective than utilizing conventional methods for a single detection (about 0.04 USD for each target) because of the straightforward design of our detection instruments, their superior anti-interference capabilities, and the low cost of routine instrument maintenance.

A personal glucose meter-utilized strategy for portable and label-free detection of hydrogen peroxide

Rapid and precise detection of hydrogen peroxide (H2O2) holds great significance since it is linked to numerous physiological and inorganic catalytic processes. We herein developed a label-free and washing-free strategy to detect H2O2 by employing a hand-held personal glucose meter (PGM) as a signal readout device. By focusing on the fact that the reduced redox mediator ([Fe(CN)6]4-) itself is responsible for the final PGM signal, we developed a new PGM-based strategy to detect H2O2 by utilizing the target H2O2-mediated oxidation of [Fe(CN)6]4- to [Fe(CN)6]3- in the presence of horseradish peroxidase (HRP) and monitoring the reduced PGM signal in response to the target amount. Based on this straightforward and facile design principle, H2O2 was successfully determined down to 3.63 μM with high specificity against various non-target molecules. We further demonstrated that this strategy could be expanded to identify another model target choline by detecting H2O2 produced through its oxidation promoted by choline oxidase. Moreover, we verified its practical applicability by reliably determining extracellular H2O2 released from the breast cancer cell line, MDA-MB-231. This work could evolve into versatile PGM-based platform technology to identify various non-glucose target molecules by employing their corresponding oxidase enzymes, greatly advancing the portable biosensing technologies.

Enhanced anti-cancer potency of sustainably synthesized anisotropic silver nanoparticles as compared with L-asparaginase

Acute lymphoblastic leukemia (ALL), a hematologic cancer that involves the production of abnormal lymphoid precursor cells, primarily affects children aged 2 to 10 years. The bacterial enzyme L-asparaginase produced from Escherichia coli is utilised as first-line therapy, despite the fact that 30 % of patients have a treatment-limiting hypersensitivity reaction. The current study elucidates the biosynthesis of extremely stable, water-dispersible, anisotropic silver nanoparticles (ANI Ag NPs) at room temperature and investigation of its anti-tumor potency in comparison to L-asparaginase. The optical, morphological, compositional, and structural properties of synthesized nanoparticles were evaluated using UV–Vis-NIR spectroscopy, Transmission Electron Microscopy (TEM), Fourier Transform Infrared Spectroscopy, and X-ray Diffractometer. The UV–Vis-NIR spectra revealed the typical Surface Plasmon Resonance (SPR) at 423 nm along with additional NIR absorption at 962 nm and 1153 nm, while TEM images show different shapes and sizes of Ag nanoparticles ranging from 6.81 nm to 46 nm, together confirming their anisotropic nature. Further, the MTT assay demonstrated promising anticancer effects of ANI Ag NPs with an IC50 value of ∼7 μg/mL against HuT-78 cells. These sustainable anisotropic silver nanoparticles exhibited approximately four times better cytotoxic ability (at and above 10 μg/mL concentrations) than L-asparaginase against HuT-78 cells (a human T lymphoma cell line). Apoptosis analysis by Wright-Geimsa, Annexin-V, and DAPI staining indicated the role of apoptosis in ANI Ag NPs-mediated cell death. The measurement of NO, and Bcl2 and cleaved caspase-3 levels by colorimetric method and immunoblotting, respectively suggested their involvement in ANI Ag NPs-elicited apoptosis. The findings indicate that the biogenic approach proposed herein holds tremendous promise for the rapid and straightforward design of novel multifunctional nanoparticles for the treatment of T cell malignancies.

Electrohydrodynamic drying of pollens based on a dual-polarization induction mode triboelectric nanogenerator

Drying pollen and other powders are important procedures of the food industry. Here we demonstrate a self-powered cold plasma drying system for collecting and drying pollen powders based on a dual-charge-induction mode triboelectric nanogenerator (TENG). The charge accumulation strategy of TENG has been modified by a dual-polarized module, where both ultra-high voltage output (over 30 kV) and sufficient output charge density could be generated to enhance drying efficiency. Comparing with all the other direct-current TENGs with an output voltage over 15 kV, this as-fabricated TENG can provide the highest transferred charge density so far. The electrohydrodynamic forces generated by the high-voltage TENG can be used to evaporate moisture from pollen. Within 20 min, it can lower the moisture content of fresh pollen from 35% to 7%, presenting a straightforward design for storing pollen at present. As for the same electrohydrodynamic drying process, the energy consumption of this self-powered TENG-based drying system for evaporating 1 kg water is about 5.36 kJ, which is only 36.4% of energy consumption of commercial high-voltage power source. This design provides a simple yet effective low-power consumption drying system for current pollen storage, which can be a promising environment-friendly alternative for food industry.