Steinmann Pin Research Articles

Percutaneous Reduction and Fixation of Displaced Intra-Articular Calcaneal Fractures

Despite the relative prevalence of intra-articular calcaneal fractures, definitive management is controversial. The goal of this study is to evaluate the clinical and radiological outcome of percutaneous reduction and fixation of 20 patients with intraarticular calcaneal fractures Sanders type II, III or IV by k wires, Steinmann pins or cannulated screws subjectively and objectively over 8 months .Twenty-two (22) percutaneous fixation of calcaneal fractures in 20 patients were included in this study. This study included closed intra-articular calcaneal fractures type II , III and IV in adult patients and excluded open, extra-articular, type I fractures. The American Orthopaedic Foot and Ankle Score (AOFAS) was used for evaluation. The excellent and good results were considered satisfactory while the poor and fair results were considered unsatisfactory. The results at the end of this study were satisfactory in 86.3% of patients (AOFAS score more than 75 in 19 fractures) and unsatisfactory in 13.6% of patients (AOFAS score less than 75 in 3 fractures). All patients included in this study showed normal range of motion of the ankle joint (active dorsiflexion and planter flexion) with variable decrease in the subtalar range of motion (active inversion and eversion) when compared with the normal side. .Percutaneous reduction and fixation had been found to be satisfactory in reduction of Bohler’s angle, Gissane angle and Sarrafian angle with avoiding open reduction surgical and postoprtative complications and avoiding conservative management bad functional outcome.

Do We Really Need to Worry About Calcaneocuboid Subluxation During Lateral Column Lengthening for Planovalgus Foot Deformity?

Although lengthening of the lateral column through an osteotomy of the anterior calcaneus is an integral component of flatfoot reconstruction in younger patients with flexible planovalgus deformities, the procedure has been implicated in iatrogenic calcaneocuboid (CC) subluxation and subsequent degenerative changes at the CC articulation. The purpose of this study is to characterize alterations at the CC joint after lateral column lengthening (LCL) and determine if Steinmann pin stabilization of the CC joint before distraction maintains a normal relationship. Seven matched pairs of fresh-frozen cadaveric feet underwent preprocedure plain radiography and cross-sectional computed tomography (CT) imaging. LCL by osteotomy through the anterior calcaneus was then performed. One foot of each matched pair had a single smooth Steinmann pin placed centrally across the CC joint before osteotomy distraction. Distraction across each osteotomy was then performed and maintained with a 12-mm porous titanium wedge. Repeat imaging was obtained and compared with preprocedure studies to quantify sagittal and rotational differences at the CC articulation. Following LCL, plain radiography demonstrated statistically significant increases in the percentage of the calcaneal articular surface dorsal to the superior aspect of the cuboid in both the pinned (8.2% vs. 17.6%, P=0.02) and unpinned (12.5% vs. 16.3%, P=0.04) specimens. No difference in the percentage of subluxation was found between the 2 groups after LCL. CT imaging demonstrated statistically significant increases in rotation between the calcaneus and cuboid after LCL in both the pinned (7.6±5.6 degrees, P=0.01) and unpinned (17±12.3 degrees, P=0.01) specimens. The degree of rotation was greater in unpinned specimens after LCL (P=0.043). Both sagittal and rotatory subluxation seem to occur at the CC joint after LCL regardless of pin stabilization. As a single pin would be expected to limit pure translation while having little effect on rotation, it is possible that the rotational changes identified on 3-dimensional imaging are interpreted as dorsal translation when viewed 2 dimensionally using plain radiography. Consideration should therefore be given to CC stabilization with 2 pins during LCL to prevent this rotatory subluxation. Level V-cadaver study.

Treatment of Radius Curvus in a Young Dog with Association of Radial Physeal Stapling, Ulnar Ostectomy and Transarticular Dynamic External Fixator Techniques

Background: Radius curvus is a clinical manifestation of the premature closure of the distal ulnar physis and the most common physeal disease in dogs, representing 63% of all physeal injuries. There are few reports indicating the technique of stapling for treatment of radius curvus in squeletically immature dogs. The aim of this study is to report a case of radius curvus in a young dog successfully treated with a combination of 3 surgical tecniques: 1- Stapling the medial and cranial portions of the distal radial physis; 2- Oblique osteotomy of the proximal ulna and ostectomy of the distal ulna, and 3- Dynamic external skeletal fixation in the elbow joint.Case: A 5-month-old female dog was referred to the University Veterinary Hospital with a history of left thoracic limb deformity for 2 weeks. There was a history of possible traumatic event on the front limb, in addition to providing nutritional supplements daily. In the radiographic evaluation the changes were identified in the left thoracic limb: shortening of the ulna, procurvatum and medial angulation of the distal radius, increased joint space and articular incongruity of the elbow joint. The dog was subjected to surgical treatment by the combination of three main surgical techniques. For the stapling of the distal radial physis the surgical approach on the cranial-medial surface of the distal radius was made. Two surgical staples were positioned in the distal radial physis. Thereafter a caudal approach was made to the distal region of the ulnar diaphysis for the distal ostectomy of the ulna. A bone segment of 1 cm in length of the distal ulnar diaphysis was removed. Another caudal approach was made to the proximal region of the ulnar diaphysis and a proximal oblique osteotomy of the ulna was performed. For the dynamic external skeletal fixation in the elbow joint two Steinmann pins were inserted. The first pin was proximal to the supracondilar foramen of the humerus and the second pin was caudal to the trochlear notch of the ulna, both parallel to the joint surface. To create a dynamic system, the pin tips were connected with elastic rubber bands on the medial and lateral sides of the elbow joint. Clinical and radiographic revaluation were made at 15, 30 and 60 days after surgery. Total correction of the limb deviation was achieved at 60 days postoperative. Two years after the surgical procedure, the owner was contacted and reported that the dog was very well and with no change in the operated limb.Discussion: The most common cause of premature closure of the distal ulnar physis is trauma. Due to the proper conical shape of the distal ulnar physis, there is more predisposition to the compression of the germinative cells in traumatic events, leading to radius curvus disease. Another cause of the radius curvus is the nutritional disbalances. In the reported case the patient had both predisponent factors, although unilateral limb involvement suggested trauma with primary causative agent. The treatment included the interruption of the supplementation of the diet associated with surgical techniques. The stapling of the distal radial physis is usually indicated for mild angular valgus deviation. In the current case the technique was applied with success regardless of the higher grade of radial deviation. Generally, the ulnar ostectomy is preferred to the osteotomy, since it reduces the rate of ulnar osteosynthesis, ensuring that the restrictive effect of the ulna upon the radial growth does not restart. In the reported case the ulnar ostectomy was associated with ulnar osteotomy to achieve a more effective result. Furthermore, the proximal ulnar osteotomy is usually indicated when elbow subluxation is present. In the current case the joint congruence was improved with the use of the dynamic external skeletal fixator.

Outcomes of intramedullary steinmann pin fixation for concurrent fibula fracture in comminuted tibia shaft or distal metaphyseal tibia fractures

Background: Fracture of the tibia shaft accounts for 17% of lower extremity fractures, with concurrent fibula fracture in about 78% of these cases. Intramedullary fixation for fibula fractures can restore fibula alignment and thus facilitate fracture reduction, especially in cases with comminuted shaft or distal metaphyseal tibia fractures. Methods: Patients who had internal fixation of comminuted tibia shaft or distal metaphyseal tibia fracture and a concurrent fibular fracture treated with intramedullary Steinman pin fixation were included in this study. Patients' demographic data and fracture patterns were analyzed retrospectively. Postoperative X-rays were used for fracture union evaluation and alignment analysis. Results: Nine males and one female were included in the present study. Tibia fractures were classified as four OTA42 and as six OTA43, including one type I, two type II, one type IIIA, and three type IIIB open fractures. Intramedullary nail and locking plate were used as definitive fixation in four and six cases, respectively. Complications required additional surgeries including wound debridement for one patient, bone graft for three patients, and revision surgery from a broken plate to an intramedullary nail for one patient. A total of 14 fibula fractures were identified in ten patients due to four segmental fractures. Eight were Weber type C, one was Weber type B, and five were midshaft fractures. The mean duration of fibula fracture healing according to radiographs was 6.9 months. Conclusions: This study suggests that intramedullary Steinmann pin fixation for concurrent fibula fracture is a critical procedure when dealing with comminuted shaft or distal metaphyseal tibia fractures.

Comparison of Bending Strength among Plate, Steinmann Pin, and Headless Compression Screw Fixations for Proximal Ulnar Shaft Fracture in Sawbones

Purpose: Although plate osteosynthesis is commonly used to treat proximal ulna fracture, its treatment method is controversial because of complications such as large incision, long operation time, and soft tissue injury. Therefore, intramedullary headless compression screw (HCS) and Steinmann pin are considered as alternative treatment options. In this study, we aim to compare bending strength of plate and cortical screws, HCS, and Steinmann pin for proximal ulnar shaft fracture with sawbone. Methods: Transverse type fractures were made intentionally at the distal 7 cm from the proximal end of ulna sawbones and fixated with plate, HCS, and Steinmann pin after reduction. Three-point bending tests were performed with total of 21 sawbones, seven pieces for each group. Results: Average ultimate bending strength for each group was as follows; 521.7N for plate fixation group, 706.4N for HCS fixation group, and 812.6N for Steinmann pin fixation group. Statistically significant results were observed among the three groups (p<0.01). When two groups were compared separately, Steinmann pin fixation and plate fixation (p<0.01), Steinmann pin and HCS fixation (p=0.047) showed statistical significance. There was a significant trend between HCS and plate fixation group (p=0.064).Conclusion: HCS and Steinmann pin fixation showed higher bending strength when compared to plate fixation for proximal ulnar shaft fracture in sawbone. Although further studies are needed, HCS and Steinmann pin fixation are promising fixation methods that may be used as an alternative to plate fixation.

Induced membrane technique with sequential internal fixation: use of a reinforced spacer for reconstruction of infected bone defects.

To evaluate a novel sequential internal fixation strategy using a reinforced spacer for infected bone defect reconstruction by the induced membrane technique (IMT). A retrospective case study was performed among patients treated for infected bone defects by applying this strategy. Following radical debridement, temporary stabilization was provided by a massive cement spacer combined with minimal intramedullary fixation during step 1. Definitive internal fixation was performed together with bone grafting at step 2. Eight patients with a mean age of 58 years were reviewed. The mean bone defect length was 8.8 cm. The spacer armature mostly consisted of elastic nails and Steinmann pins. Iterative debridement was required in one case after step 1. The mean interval between steps was 12 weeks. Definitive internal fixation was performed by intramedullary nailing (n = 4) or plating (n = 4). At a mean follow-up of 21 months, bone union was achieved in seven cases without additional bone grafting or infection recurrence. Sequential internal fixation using a reinforced cement spacer seems to be a valuable option for avoiding external fixation between IMT steps and limiting the recurrence of infection.

Reemplazo total de cadera en un paciente con amputación supracondílea homolateral

Las fracturas de cadera en pacientes con amputación del miembro homolateral son lesiones infrecuentes que representan un reto para el cirujano ortopédico. Presentamos el caso de un hombre de 63 años con amputación supracondílea izquierda, que sufre una fractura de cuello femoral izquierdo por caída de su propia altura. La colocación apropiada del implante es esencial para obtener buenos resultados clínicos posoperatorios. Para la exposición y la colocación del implante se utilizó un clavo de Steinmann en el trocánter mayor. No se observaron complicaciones clínicas ni radiográficas en un seguimiento de 15 meses. Creemos que el empleo del clavo de Steinmann colocado en una correcta posición es una buena alternativa por considerar para poder controlar el miembro al realizar una artroplastia y así disminuir los riesgos de colocar la prótesis en mala posición y el tiempo quirúrgico.
 

Comparative study of surgical management versus conservative management of displaced fractures of the clavicle

Back ground and objectives: Clavicle fracture accounts for approximately 2.6% of all the skeletal fractures. These fractures are often associated with shoulder girdle injuries in approximately 44% of cases. Non operative treatment has been a mainstay of a modality of treatment, and irrespective of the type of fracture and amount of comminution, all these fractures were treated non-operatively. Different surgical methods for clavicle midshaft fractures have been described and these are locking compression plate fixation, intramedullary K-wires, Steinmann pin fixation, and intramedullary nailing with TENS. Therefore in this study we have compared the functional outcome of displaced clavicle fractures treated by non-surgical management with that of surgical management by TENS and by open reduction and internal fixation with clavicular locking compression plate. Methods: 60 patients with clavicle fractures presenting to the Orthopaedic Department of R L Jalappa hospital from Nov. 2017 to April 2019 are included in the study after obtaining informed consent. Result: Among 60 patients with clavicle fractures, majority of the injury occurred in male patients- 45 cases (75%), whereas a total of 15 cases (25%) were seen in females. The functional outcome at the end of 6 months in 30 conservatively managed cases showed, 4 cases (13.3%) with excellent outcome; 6 cases (20%) had good outcome. 16 cases (53.3%) had fair and 4 cases (13.3%) had poor outcome. While in surgically managed 30 cases, the functional outcome at the end of 6months showed a total of 23(76.6%) cases with excellent outcome, 4 cases (13.3%) had good outcome 2 cases (6.6%) had a fair, and 1 case (3.33%) had poor outcome. At the end of 6 months, functional outcome of both the groups were compared by applying chi square test, the p value was

Novel and reproducible technique coping with intraoperative anchor pullout during arthroscopic rotator cuff repair.

To evaluate the incidence of intraoperative anchor pullout during arthroscopic rotator cuff repair, to compare the outcomes of different methods of managing anchor pullout, and to introduce a new technique for anchor pullout. 1076 patients who underwent arthroscopic rotator cuff repair using a single-row repair technique were included. In 483 patients, rotator cuff repair was performed using a screw-in type anchor, and in 593 patients, soft anchors were used. When intraoperative anchor pullout occurred, it was managed by buddy screwing, anchor insertion in a different location, cement augmentation, or by bar anchoring using a threaded Steinmann pin. Plain radiography and sonography were used to check anchor locations and healing. Fifty-two patients experienced anchor pullout intra- or postoperatively (48 and four patients, respectively). Anchor pullouts were more frequently observed for larger tears, women, older patients, and in patients with preoperative stiffness (limitations of both active and passive movements of the affected shoulder joint). For screw-in type anchors, pullout during surgery occurred in 16 patients (3.3%, 16/483), and all were managed using the buddy screwing technique. For soft anchor cases, pullout occurred in 32 patients (5.4%, 32/593) and was managed by anchor insertion in a different location (17 patients), cement augmentation (two patients), or bar anchoring using a threaded Steinmann pin (13 patients). Three patients managed by buddy screwing and two patients managed by anchor insertion in a different location had anchor failure after repair. Tendon healing at 6months was observed in 12/16 patients treated by buddy screwing, 11/17 treated by anchor insertion in a different location, 2/2 treated by cement augmentation, and 12/13 treated by bar anchoring with a threaded Steinmann pin. Intraoperative anchor pullout during arthroscopic rotator cuff repair is an uncommon but cumbersome complication. There are some techniques already introduced to deal with this complication. In comparison, not one technique is overwhelmingly superior to others; however, our new technique which is bar anchoring with a threaded Steinmann pin could be another solution, since it could utilize primary anchor sites and results appear to be acceptable. Level of evidence III.

Steinmann Pins and Polymethylmethacrylate Repair of Fourth Lumbar Vertebral Fracture and Dorsocranial Luxation in PuppySteinmann Pins and Polymethylmethacrylate Repair of Fourth Lumbar Vertebral Fracture and Dorsocranial Luxation in Puppy

Background: Acute spinal traumas can lead to irreversible damage associated with vascular and inflammatory changes in neural tissue. Since spine and spinal cord traumas have an unfavorable prognosis in small animals, and reports of the use of Steinmann pins and polymethylmethacrylate repair of lumbar vertebra fracture-luxation in puppies are rare in the literature, the present paper aimed to report the surgical treatment of transversal fracture through the body of the fourth lumbar vertebra, with dorsocranial displacement of the caudal fragment by using Steinmann pins and polymethylmethacrylate in a 7-month-old Labrador Retriever male dog.Case: A 7-month-old intact male Labrador Retriever dog, weighing 24.0 kg was attended at School Veterinary Hospital with a history of hit by car and paraplegia of the hind limbs. On neurological examination was observed no proprioception and no deep pain sensitivity on the both pelvic limbs. The lumbar spinal palpation showed intense pain, and the motor function and patellar reflexes were reduced. The values of haematological and biochemical analysis remained within the reference values for the species. Radiographs revealed a transversal fracture through the body of the fourth lumbar vertebra, with dorsocranial displacement of the caudal fragment, and was decided to perform a surgical treatment by open reduction and internal fixation of the fracture. The dog was positioned in ventral recumbency for surgery, and a dorsal midline incision was made from the second lumbar vertebra to the sixth lumbar vertebra. Two crossed 1.5 mm Kirschner wires were placed through the caudal articular facets of the fourth lumbar vertebra to provide initial stability. Two 2.0 mm Steinmann pins were placed at 60° angle of the bodies of the second and fifth lumbar vertebrae, and third and fourth lumbar vertebrae. This procedure was repeated on the other side of the vertebral bodies. Sixty grams of polymethylmethacrylate bone cement was applied and the fixation was checked for stability. Muscular, subcutaneous tissue and skin was closed routinely. The dog was paraplegic without any pain and used a wheelchair to assist in locomotion, although it still had urinary and faecal incontinence; no tail control; and the implants were not removed.Discussion: Lumbar vertebral injuries, as in the present case frequently, occur secondary to severe trauma (e.g. hit by car) and seem to have a characteristic fracture pattern. The patient became paraplegic due to spinal cord injury and failure of sensitivity and elimination of urine and feces which can be associated with progressive destruction of neuronal tissue due to secondary vascular and inflammatory events. The radiographic exam was used to confirm the spinal injury and determine whether by conservative or surgical treatment. The treatment choice is related to the number of fractured compartments, and the presence or not of compression. Fractures in two or more compartments are indicative of surgical treatment, similar as the present case. Use of Steinmann pins was to make a rigid fixing system compared with block plates used for the same function. Use of polymethylmethacrylate may also become a complication due to the infection, for this reason was prescribed an antibiotic for 15 days. This procedure proved to be effective since the dog showed no signs of infection. According to the characteristics of the present case report, the use of Steinmann pins and polymethylmethacrylate for repair of transversal fracture through the body of the fourth lumbar vertebra, with dorsocranial displacement of the caudal fragment provided an effective and practical means of stabilisation, promoting decompression, and thus, improving the patient's quality of life.

Techniques for Patient Positioning During Burn Surgery: A Systematic Review.

Patient positioning in the operating room remains a challenge for burn surgeons; burn surgery involves critically ill patients who require close monitoring, difficult exposures, and careful handling of grafted areas. Various techniques to optimize intraoperative positioning during burn surgery have been described in the literature. The aim of this review was to outline these positioning techniques and report on their complications. A systematic review was performed by 2 independent reviewers using PubMed, Scopus, and OvidSP MEDLINE databases. Articles were included if they described intraoperative techniques to position patients undergoing burn surgery. The primary variable of interest was complications related to positioning during surgery. The search identified 1855 nonduplicate citations, of which 29 underwent full-text review, and 10 met inclusion criteria. Three studies described overhead suspension techniques, including a hook-and-pulley system, ceiling chains, weighted IV poles, and mounted crossbars; no complications were reported. Six studies described limb fixation techniques, including Steinmann pins, finger traps, wrist/ankle wraps, towel clips through eschar or distal phalanges, and external fixators. Complications included one case of hardware failure of external fixation and several pin site infections. Four studies described table modification techniques, including a modified Stryker frame, a fracture table, the Mayfield headrest, and the recliner position; no complications were reported. Numerous techniques have been described to improve patient positioning during burn surgery. No major complications were identified in this systematic review. Most techniques use standard operating room equipment and can aid in safe and easier operations.

A Simple Percutaneous Technique to Reduce Valgus-Impacted Femoral Neck Fractures.

The mainstream surgery for valgus-impacted femoral neck fractures (FNFs) is closed reduction and internal fixation under fluoroscopy. However, femoral neck shortening and anterior femoroacetabular impingement are common complications in healed valgus-impacted FNFs after in situ fixation. Some methods have been reported to prevent complications, but these techniques require the use of a transfixing guide wire that passes through the femoral head, which may cause articular cartilage damage. We introduce a simple reduction technique using one Steinmann pin (S-pin) for valgus-impacted FNFs without any interference of the femur head. A S-pin was placed percutaneously at the inferomedial margin of the fracture, and reduction was achieved by applying manual valgus force along the fracture line. By restoring the anatomical alignment, we confirmed the maximum contact area of the fracture and connection of the medial cortical buttress, so the risk of nonunion was also minimized.

Clinical and Radiological Outcomes after Various Treatments of Midshaft Clavicle Fractures in Adolescents.

BackgroudControversy exists about the optimal treatment of midshaft clavicle fractures in the presence of significant displacement, comminution, or shortening of the fracture in adolescents. The purpose of this study was to compare the clinical and radiological outcomes of 4 different treatments for midshaft clavicle fractures in adolescents: conservative treatment with a figure-of-8 (FO8) brace, open reduction and internal fixation with a plate (OPL), minimally invasive plate osteosynthesis (MIPO), and intramedullary nail fixation with a threaded Steinmann pin (TSP).MethodsA total of 94 teenagers with midshaft clavicle fractures were divided into the FO8, OPL, MIPO, and TSP groups (n = 24, 33, 16, and 21, respectively). We analyzed clinical and radiological outcomes and complications in each group and compared the results among the groups.ResultsAll groups showed satisfactory clinical and radiological outcomes, but each group showed different results for the assessment items. The Constant-Murley scores were higher in the operated groups than in the FO8 group. Recovery of joint motion was faster in the operated groups. The TSP group had the highest cosmetic satisfaction with respect to the satisfaction score and measured scar length. Fracture union was achieved in all patients. At the final follow-up, the bone length was closer to normal in the OPL and TSP groups than in the FO8 and MIPO groups, and angulation was less in the OPL and TSP groups than in the MIPO and FO8 groups. The TSP and MIPO groups obtained faster bone healing than the OPL and FO8 groups. In the operated groups, 9 patients had metal-induced irritating symptoms; 1, supraclavicular nerve injury symptoms; and 4, refractures after plate removal.ConclusionsThe nonoperatively treated group had no iatrogenic complications. The operated groups complained of various disadvantages induced by surgery; however, these groups achieved faster functional recovery and slightly better radiological and functional results than the nonoperative group.

Steinmann pin retractor-assisted reduction with circle plate fixation via sinus tarsi approach for intra-articular calcaneal fractures: a retrospective cohort study

BackgroundSinus tarsi approach and mini-calc plate have been used for intra-articular calcaneal fractures. However, the sinus tarsi approach has limited exposure to the lateral wall, which makes it challenging to obtain an excellent anatomic reduction of the calcaneal body. What is more! To restore the width of the calcaneal body entirely and prevent the heel varus simultaneously with mini-calc plate was tough as well. Aimed to solve the aforementioned problems, our study focused on using the Steinmann pin retractor for reduction and the circle plate for fixation via the sinus tarsi approach.MethodsFrom March 2017 to January 2019, 15 patients with closed calcaneal fractures were treated with the method of Steinmann pin retractor-assisted reduction and circle plate fixation via the sinus tarsi approach. All these patients received a positive postoperative clinical and radiological evaluation.ResultsA postoperative follow-up was done for each of the 15 patients, and the following scores and parameters were observed: value of visual analogue scale (VAS) was 1.44 ± 0.63, and The American Orthopaedic Foot and Ankle Score (AOFAS) Ankle-Hindfoot score was 84.31 ± 5.03 at the last follow-up. The Böhler angle (30.81 ± 3.56°), width (37.83 ± 4.87 mm), length (87.4 ± 3.33 mm), and height (86.23 ± 5.36 mm) of the calcaneus were improved significantly in comparison with preoperative values (− 0.94 ± 10.06°, 45.67 ± 5.68 mm, 82.72 ± 5.54 mm, 76.32 ± 7.98 mm), and these parameters were maintained excellently after 6–19 months’ follow-up.ConclusionOur present study suggested that Steinmann pin retractor-assisted reduction with circle plate fixation via the sinus tarsi approach may serve as a safe and effective method for Sanders type II and type III calcaneus fractures. The Böhler angle, height, length, and body of the calcaneus were excellently restored postoperatively and maintained at last follow-up and rare postoperative complications.Trial registrationThis study has been registered. The unique identifying number is research registry 5092.

Skeletal traction pin diameter and deflection under load: a biomechanical evaluation with clinical correlation

Background: There is scant literature to guide the placement of skeletal traction. The purpose of this study was to test a tensioned traction bow, a nontensioned traction bow, and a traction set up without a bow to measure the amount of pin deflection. By quantifying the deflection of various traction systems under load, guidelines can be provided regarding equipment selection for skeletal traction. The goal was to develop a protocol to minimize the equipment necessary and time to traction placement. Methods: A Sawbones® skeletal traction model was designed to measure the amount of deflection of Steinmann pins of various diameters using a Kirschner tensioning bow, a Böhler (nontensioning) device, and a simple design using only weight and nylon cord. Increasing weight was added to each system and deflection recorded. Data were then evaluated to determine the smallest pin diameter that can reasonably withstand a weight of 35 pounds using the cord-only traction design. Results: Overall, larger pins deflected less. When comparing the traction systems, the tensioned bow had the least deflection, followed by the nontensioned bow, and the cord-only system. In the cord-only system, the 2.8-mm pin was the smallest diameter that successfully withstood the maximum weight without failing. The cord-only design was left in place for 48 hr without further increase in deflection. Conclusions: A simple skeletal traction design consisting of a 2.8-mm smooth Steinmann pin, segment of nylon cord, and weight can be applied with limited tools in a safe and efficient manner.

Alterations in tibiotalar joint reaction force following syndesmotic injury are restored with static syndesmotic fixation

IntroductionSyndesmotic injury alters joint mechanics, which may fail to be restored unless an anatomic reduction is obtained. MethodsA minimally invasive method of measuring joint forces was utilized that does not require significant dissection or intraarticular placement of sensory instruments. Steinmann pins were placed in the tibia and talus of eight fresh-frozen human cadaveric lower extremities and a baseline joint reaction force was determined. A syndesmotic injury was created and reduction (anatomic and anterior malreduction) performed with one or two quadricortical screws and joint reaction forces were measured after the injury and subsequent repairs. FindingsBaseline mean tibiotalar joint reaction force was 31.4 (SD 7.3 N) and syndesmotic injury resulted in a 35% decrease (mean 20.3, SD 8.4 N, p < 0.01). Fixation of the injury using one or two syndesmotic screws resulted in significant increase compared to the injury state (mean 28.7, SD3.9 N, and mean 28.3, SD 6.4 N, p < 0.05), however there was no significant difference between the two methods of fixation. Malreduction of the fibula also increased joint reaction force compared to the injury state (mean 31.5, SD 5.2 N, p < 0.01), however a significant difference was not detected between malreduction and anatomic reduction. InterpretationThe present study demonstrates that syndesmotic injury decreases joint reaction force within the tibiotalar joint, suggesting ankle joint instability. Tibiotalar force was restored with anatomic reduction with either a 1 or 2 quadricortical syndesmotic screws. Furthermore, anterior malreduction restored joint reaction force to levels similar to those observed at baseline and with anatomic reduction.Level of Evidence: Level V: biomechanical/cadaver study.

What’s New in Orthopaedic Trauma

What’s New in Orthopaedic Trauma

Fassier-Duval Rods are Associated With Superior Probability of Survival Compared With Static Implants in a Cohort of Children With Osteogenesis Imperfecta Deformities.

The survival of Fassier-Duval (FD) telescoping rods as compared with static implants in children affected by osteogenesis imperfecta is not well characterized. The purpose of this study was to compare risk of lower extremity implant failure in FD rods versus static implants. Data were retrospectively collected from patients with osteogenesis imperfecta who underwent surgical treatment using either FD rods or static implants (Rush rods, flexible nails, or Steinmann pins) between 1995 and 2015. The timing of implant failure was the primary outcome variable of interest. Comparisons were limited to limbs with no previous history of implants. Cox-proportional hazards regression analyses were used to compare the hazard of implant failure across implants. Negative binomial regression analyses were used to compare the incidence of surgical procedures in the 2 implant groups. The final cohort consisted of 64 limbs (n=21 patients). The static implant group (n=38) consisted of 24 Rush rods (63%), 14 flexible nails (37%), and 2 Steinmann pins (5%). The hazard of implant failure in the static implant group was 13.2 times [95% confidence interval (CI), 2.5-69.6; P=0.0024] the hazard of implant failure in the FD rod group. The hazard of implant failure among females was 4.8 (95% CI, 1.4-16.7; P=0.0125) times the hazard of implant failure among males. The total surgery rate in the static implant group was 7.8 (95% CI, 1.8-33.0; P=0.0056) times the total surgery rate in the FD group. Among surgically naive limbs, FD rods were associated with significantly improved probability of survival compared with static implants. Level II-retrospective study.

Correlation of Fracture Energy With Sanders Classification and Post-traumatic Osteoarthritis After Displaced Intra-articular Calcaneus Fractures.

To quantify fracture severity for a series of displaced intra-articular calcaneal fractures (DIACFs) and to correlate it with Sanders classification, post-traumatic osteoarthritis (PTOA), and patient outcomes. Retrospective review and fracture severity analysis. Level 1 trauma center affiliated with the University of Iowa in Iowa City, IA. Thirty-six patients with 48 DIACFs were selected from 153 patients previously treated. All patients 18 years of age and older who had available electronic preop and postop computed tomography (CT) scans, good-quality postop and follow-up radiographs, and a follow-up ≥18 months were selected for study. Fractures were treated with percutaneous reduction, using multiple small stab incisions and fluoroscopy to guide manipulation of articular fragments using cork screws or Steinmann pins, with subsequent fixation using 3.5- and 4.0-mm screws. Preop CT scans were used to grade fractures according to the Sanders classification and to quantify fracture severity. Fracture severity was objectively quantified using a CT-based measure of fracture energy. PTOA was assessed on follow-up radiographs using the Kellgren-Lawrence scale. Patient outcomes were assessed using the Short Form 36 (SF-36) questionnaire and a visual analog scale pain score. Fracture energies for the 48 DIACFs ranged from 14.1 to 26.2 J (19.3 ± 3.1 J) and correlated with Sanders classification (rho = 0.53, P = 0.0001); type I (16.3 ± 0.9 J); type II (18.0 ± 2.7 J); type III (20.8 ± 2.8 J); and type IV (22.0 ± 0.7 J). Fracture energy was higher for fractures in which the subtalar joint developed PTOA (19.5 ± 2.7 J) than for those that did not (18.9 ± 3.3 J), but the difference did not reach statistical significance. The Sanders classification predicted PTOA risk [odds ratio (OR) = 4.04, 95% confidence interval = 1.43-11.39, P = 0.0084]. No relationship was observed between fracture energy and visual analog scale pain scores. Higher fracture energy correlated with lower SF-36 scores. Fracture energy positively correlates with Sanders classification for DIACFs, which can be used to identify more severe fractures at greater risk of progressing to PTOA. Prognostic Level III. See Instructions for Authors for a complete description of levels of evidence.

Skeletal traction for the management of lower limb fractures: Its relevance today

Purpose: Skeletal traction is one of the modalities of treatment for fractures involving appendicular skeleton. The purpose of our study is to evaluate the clinical and radiological outcomes of skeletal traction applied to injuries involving lower limb as a temporary / definitive procedure.Methods: We have included 108 patients with various injuries involving bones of lower limb. Modalities of traction included upper/lower tibial pin traction/calcaneal pin traction. Steinmann pins (4.5mm to 5.5mm) Bohler stirrup and Bohler Braun splint were used for applying traction. X-rays were taken before and after skeletal traction and also every time when the weight of traction was either increased or decreased. The end point for removal of the traction apparatus was either surgery or POP application or fracture union. Until then quadriceps and ankle mobilisation exercises were performed. Results: Results were analysed based on skin healing, bone healing, joint scores (Harris hip score, WOMAC score, Peterson score). Complications usually encountered were pin tract Infections. Most of the cases showed good results in either assisting the surgeon for closed manipulation and implantation during surgery, or for successful healing in good alignment in patients who were not fit for surgery or not willing for surgery.Conclusion: Skeletal traction, even though rarely used nowadays, is still an important modality of treatment in selected situations where surgery may be delayed, denied or contraindicated for various reasons.