Stainless Steel Weld Research Articles

Influence of Current Welding on Mechanical Properties and Microstructure of Argon Arc Welding of Type-304L Austenite Stainless Steel

Influence of Current Welding on Mechanical Properties and Microstructure of Argon Arc Welding of Type-304L Austenite Stainless Steel

Stress Relaxation Cracking in 347H Stainless Steel Arc Welds: Susceptibility Evaluation of Heat-Affected Zone

Stress relaxation cracking (SRC) is considered one of the major failure mechanisms for 347H stainless steel welds at elevated service temperatures or during post weld heat treatment (PWHT), especially within the heat-affected zone (HAZ). This work focuses on the characterization of SRC susceptibility within 347H physically simulated arc welded HAZ at elevated temperatures. A four-step SRC thermomechanical test in combination with finite element modeling (FEM) of the welding and testing processes is developed to establish a susceptibility map for HAZ. The test first runs a thermal cycle with three different peak temperatures (1335, 1275, and 1150 °C) to duplicate representative HAZ subzone microstructures, followed by time-to-failure examination under a variety of pre-stress (260–600 MPa) and pre-strain conditions (0.03–0.19) as a function of reheat temperatures between 750 and 1050 °C. With the aid of FEM, SRC susceptibility maps are generated to identify the threshold stress, plastic strain, and creep strain as a function of test temperature. It was found out that HAZ subzone with a lower peak temperature (1150 °C) appears to be slightly less susceptible to SRC than the other two subzones that experienced higher peak temperatures. Generally, time-to-fracture reduces with increasing initially applied stress and strain for all test temperatures. The pre-stress thresholds decrease from about 500 to 330 MPa as the testing temperature increases from 800 to 1050 °C, while the corresponding initial plastic strain thresholds reduces from 0.15 to 0.06. The SRC susceptibility was also evaluated through the Larson–Miller Parameter (LMP) analysis as a function of plastic strain, initial stress and starting stress upon reaching the testing temperature, respectively. The 1050 °C test with a high pre-applied strain (0.1) exhibits an extremely short time to failure (t = 3 s) that lies outside the general trend in LMP analysis. Additionally, it was identified that a plastic strain above 0.07 is identified to significantly reduce the bulk creep strain tolerance to fracture and therefore increases SRC susceptibility. Hardness measurement and fractography analysis indicated that the strain aging of niobium carbonitrides and other potential phases in conjunction with intergranular precipitates contributes to an increase in microhardness and increased intergranular cracking susceptibility.

Effects of Aging at 550 °C on α′-Martensitic Transformation of High Si-Bearing Metastable Austenitic Stainless Steel Weld Metal

Effects of Aging at 550 °C on α′-Martensitic Transformation of High Si-Bearing Metastable Austenitic Stainless Steel Weld Metal

Experimental and numerical investigation on laser transmission welding of stainless steel 304 L and borosilicate glass

Experimental and numerical investigation on laser transmission welding of stainless steel 304 L and borosilicate glass

Micro-macro properties of stainless-clad bimetallic steel welded connections with different configurations

This paper aims to investigate the microstructure and mechanical properties of S31603 + Q355B stainless-clad (SC) bimetallic steel welded connections with different welding configurations. A comprehensive research approach was employed, including microstructure analysis, static tensile test, impact test, bending test, Vickers hardness distribution measurement, and analysis of welding economy and efficiency. Four types of welded connections were examined to understand their performance variations arising from different welding configurations. Based on the findings, a recommended welding configuration suitable for structural engineering applications was proposed. Research outcomes showed that the decarburization and carbon accumulation zones were observed at the fusion interface during the welding of dissimilar metals. It should be noted that martensite was formed in the substrate, or the base metal, due to diffusion of alloying elements, with a more pronounced effect observed with higher welding heat inputs. In order to minimize the fusion area of dissimilar metals, it is advisable to avoid using a single welding consumable made of stainless steel as the mechanical properties of the welded connection were not significantly influenced by the use of stainless steel welding consumables with higher Nickle (Ni) and Chromium (Cr) alloying content in the transition region. Consequently, the same welding consumable should be employed in the transition region to simplify the welding procedure and to enhance the welding efficiency.

The Analysis of Electrode Combination Effect on Steel and Stainless Steel Welding (Overview of Tensile and Metallography Test)

The Analysis of Electrode Combination Effect on Steel and Stainless Steel Welding (Overview of Tensile and Metallography Test)

In situ chemical analysis of duplex stainless steel weld by laser induced breakdown spectroscopy

The high corrosion resistance and good mechanical properties of duplex stainless steel (DSS) are due to its special chemical composition, which is a balanced phase ratio of ferrite (α) and austenite (γ). Many industrial applications require the integration of DSS components. For this, Gas tungsten arc welding (GTAW) is an excellent choice, as it allows an automated operation with high reproducibility. However, when the weld pool solidifies, critical ratios of α- and γ- phases can occur, which lead to solidification cracking, increased susceptibility to corrosion, and a decrease in ductility and critical strength. Previous studies have shown that these defects can be caused by the accumulation of manganese and chromium in the heat affected zone (HAZ), requiring ongoing monitoring of this accumulation. A suitable method for such monitoring is laser-induced breakdown spectroscopy (LIBS), which can be used in two operating modes: calibration using standard reference samples and calibration-free. Unlike conventional quantitative LIBS measurements, which require reference samples to generate a calibration curve, calibration-free LIBS (CF-LIBS) allows chemical compositions to be determined solely from the emission spectrum of the plasma. Numerous publications show that CF-LIBS is a fast and efficient analytical method for the quantitative analysis of metal samples. In this work, CF-LIBS is applied to spectra obtained during GTAW DSS welding and the result is compared with those obtained by PLS analysis. A good correlation was found between both types of analysis, demonstrating the suitability of the CF-LIBS method for this application. The CF-LIBS method has a significant advantage over conventional LIBS due to the rapid in situ measurement of concentrations of major alloying elements without calibration procedure. This, combined with fast feedback and appropriate adjustment of welding parameters, helps prevent welding defects.

Physical simulation of low temperature phase separation during multipass welding of super duplex stainless steel

This study aimed to investigate the degree of low-temperature phase separations and 475 °C -embrittlement in physically simulated multipass super duplex stainless steel (SDSS) welds. A single bead weld was produced using gas metal arc welding and multiple thermal cycles with different peak temperatures were applied using a Gleeble physical simulator with fixed and moving jaws to simulate the influence of constrained designs, to mimic the welding of thick SDSS components. The samples were studied using atom probe tomography and the results were correlated with toughness and ferrite microhardness. The results showed that the microhardness of the ferrite in the constrained simulated multipass reheated weld increased from 304 HV to 374 HV after 5 min aging at 475 °C. The amplitude of the Cr concentration of the same sample, showing the level of Fe-Cr phase separation, increased from 1.025 to 1.045 after 5 min aging at 475 °C. Despite the clear development of phase separation in the ferrite, the toughness did not drop. It can be concluded that reheated SDSS welds are not susceptible to 475 °C -embrittlement during short fabrication times of up to 5 min for the austenite level of 50%.

Modelling the Evolution of Phases during Laser Beam Welding of Stainless Steel with Low Transformation Temperature Combining Dilatometry Study and FEM

In this study, the evolution of volume fractions during laser beam welding (LBW) of stainless steel, with a specific focus on incorporating the low transformation temperature (LTT) effect using the dilatometer, has been proposed. The LTT effect refers to the phase transformations that occur at lower temperatures and lead to the formation of a martensitic microstructure, which will significantly influence the residual stresses and distortion of the welded joints. In this research, the LTT conditions are achieved by varying the Cr and Ni content in the weld seam by varying the weld parameter, including laser power, welding speed and filler wire speed. The dilatometer analysis technique is employed to simulate the thermal conditions encountered during LBW. By subjecting the stainless steel samples to controlled heating and cooling cycles, the kinetics of the volume fractions can be measured using the lever rule and empirical method (KOP and Lee). The phase transformation simulation model is computed by integrating the thermal and metallurgical effects to predict the volume fractions in LBW joints and has been validated using dilatometer results. This provides valuable insight into the relationship between welding parameters and phase transformations in stainless steel with the LTT effect during laser beam welding. Using this relationship, the weld quality can be improved by reducing the residual stresses and distortion.

The strengthening role of post-welded cryogenic treatment on the performance and microstructure of 304 austenitic stainless steel weldments

The metallurgical changes and micro defects after welding can influence the mechanical property, corrosion resistance and dimensional stability of the stainless steel wielding joints. It is necessary to explore an effective post-welded method to improve the service performance for stainless steel welding joints. Furthermore, the essential mechanism between microstructure changes and macro-property variation during this process needs deep reveal. Therefore, this paper aims at investigating the effects of different post-weld treatments including naturally aging, artificial aging and cryogenic treatment on the residual stress and mechanical properties of 304 stainless steel weldments. The microstructure evolution was also studied to reveal and establish the microstructure-performance relationship. The results showed that the distribution of residual stress was most uniform with lowest magnitude (decreased by up to 49%) after cryogenic treatment. At room temperature, weldments subjected to the three post treatments showed similar mechanical properties. At cryogenic temperature, cryogenic treatment exhibited an outstanding role on maintaining the mechanical properties of weldments. By contrast, the mechanical properties were obviously reduced by artificial aging. The transformation of δ-ferrite and the carbide precipitation in grain boundaries are the main reasons for the decrease of mechanical properties after artificially aging. Welding process was able to cause the transfer of the alloying elements and decrease the stability of austenite. Consequently, martensitic transformation can be induced during cryogenic treatment. The new formed martensite resulted in the refined microstructure and high mechanical properties of weldments, and also the release of residual stress after welding.

Effect of Tool Geometry on the Microstructure of Friction Stir Welding of Copper and 316L Stainless Steel

The microstructure evolution during dissimilar friction stir welding of copper with stainless steel 316L is studied. The welding is performed in transparence configuration using tools of two different geometries. The joints are characterized by optical microscopy, scanning and transmission electron microscopy, electron backscattered diffraction, and microhardness. The microstructure and crystallographic texture of base metals are significantly affected. The joint produced using a shoulder of 8 mm in diameter is characterized by a copper nugget with refined grains. The texture of copper is dominated by component of the shear texture. The steel beneath the tool shows a grain refinement with grains of sub‐micron size and a texture which is close to the ideal simple shear texture. For the joint produced by the 16 mm diameter tool shoulder, the nugget consists of large grains of copper, while the steel beneath the tool shows small recrystallized grains of micrometer size. The texture in the steel is dominated by the component of the shear texture. The Cu/316L interface in both types of joint is of very good quality. In a detailed study of the interface, it is revealed that the welding of metals is achieved by mutual intense mechanical interlocking without formation of any intermetallic compounds.

TERT-independent telomere elongation and shelterin dysregulation after pulmonary exposure to stainless-steel welding fume in-vivo

Telomeres are inert DNA sequences (TTAGGG) at the end of chromosomes that protect genetic information and maintain DNA integrity. Emerging evidence has demonstrated that telomere alteration can be closely related to occupational exposure and the development of various disease conditions, including cancer. However, the functions and underlying molecular mechanisms of telomere alteration and shelterin dysregulation after welding fume exposures have not been broadly defined. In this study, we analyzed telomere length and shelterin complex proteins in peripheral blood mononuclear cells (PBMCs) and in lung tissue recovered from male Sprague-Dawley rats following exposure by intratracheal instillation (ITI) to 2 mg/rat of manual metal arc-stainless steel (MMA-SS) welding fume particulate or saline (vehicle control). PBMCs and lung tissue were harvested at 30 d after instillation. Our study identified telomere elongation and shelterin dysregulation in PBMCs and lung tissue after welding fume exposure. Mechanistically, telomere elongation was independent of telomerase reverse transcriptase (TERT) activation. Collectively, our findings demonstrated that welding fume-induced telomere elongation was (a) TERT-independent and (b) associated with shelterin complex dysregulation. It is possible that an alteration of telomere length and its regulatory proteins may be utilized as predictive biomarkers for various disease conditions after welding fume exposure. This needs further investigation.

Optimization and Evaluation of Mechanical and Electrochemical Properties of Ferritic Stainless Steel Welding Using Taguchi Design

The main objective of this work is to optimize welding parameters of AISI 430 FSS welds, focused to minimization of ferrite grains size using Taguchi’s design. Two input parameters of speed and welding current; were chosen to select the minimum grain size and to ascertain their effects on ferrite grain size. ANOVA method was used to evaluate the influence of varying factors on the overall quality of welds. Optimal combination of the parameters were be predicted by S/N analyses, it was accessed on employing an 80 A with 6mm/s. Experimental characterizations of optimum weld joint were performed by using tensile test assisted by image correlations, optical and electronic microscopy. As a result, welding speed had the main influence on grain size by 84.30%. Optimum welding parameter offered finest microstructure with low rate of martensite precipitates in both fusion zone and heat affected zone, and best combination of strength and ductility, it presented a homogeneous distribution of tensile stresses that caused a ductile fracture in base material. ,it is found that that optimized welding parameters permit to give greater resistance to corrosion, which exhibit a lower corrosion current, indicating that coarse ferrite grains are more susceptible to corrosion compared to fine grains.

Effect of inhomogeneous microstructure on the stress corrosion cracking behavior of 316LN stainless steel weld joint under high-temperature and high-pressure water small punch test

The stress corrosion cracking (SCC) behavior of 316LN stainless steels (SS) weld joint in high-temperature and high-pressure (HTHP) water were investigated by the newly developed HTHP water small punch test. The results indicated that SCC behavior of weld joint were strongly influenced by the inhomogeneous microstructure. Intergranular fracture dominated the SCC process of heat affected zone (HAZ) and partial hardening was believed to be the main reason for the increased sensitivity of HAZ to SCC. All samples exhibited cleavage fracture characteristics, indicating that film-induced cleavage dominated the SCC process of SS and its welded joints in HTHP water.

Laser welding of molybdenum and stainless steel with Cu[sbnd]Ti filler metal

Brittle MoFe intermetallic compounds (IMCs) are usually fatal for the joining of Mo and steel. In the present work, Ni-free joining of Mo and stainless steel was successfully achieved by laser welding with CuTi filler metal. The entry of Mo element into the weld seam and the formation of MoFe IMCs was significantly suppressed. TiFe, TiFe2, Ti5Cr8Fe16, and Cu-Ti-Fe phases were found inside the weld and near the interface. The IMCs were separated by Cu matrix and no continuous layered IMCs were found. The brittle fracture characteristics of TiFe IMCs and plastic deformation of the Cu matrix was found on the fracture surface in the weld.

Polysilazane-derived SiON coating on stainless steel weld for corrosion resistance

In this study, SiON coatings were created using perhydropolysilazane (PHPS) on the weld region and the base stainless steel region with different microstructure and composition. The influences of the weld and base steel compositions and microstructures on coating formation, composition, microstructure, mechanical properties, and corrosion resistance are discussed. The SiON coatings show a higher N content and a lower O content on the base metal than on the weld metal. Salt spray tests show that the differences in mechanical properties and compositions on the weld and base steel substrates do not significantly affect the function of the corrosion-protective coatings. However, when the coating thickness is high, the corrosion resistance decreases. This study provides important guidance regarding the desirable SiON coating and thickness for best corrosion prevention.

Stress relaxation cracking susceptibility evaluation in 347H stainless steel welds

AbstractStress relaxation cracking (SRC) has been reported as a dominant failure mechanism for 347H stainless steel welds at elevated service temperatures, occurring in either the heat-affected zone (HAZ) or fusion zone (FZ). In this study, SRC susceptibility of physically simulated HAZ and cross-welded E347-347H stainless steel welds was studied using a four-step accelerated SRC test with a thermomechanical physical simulator. The stress and temperature range studied represents weld-induced residual stress at 150–600 MPa and post-weld heat treatment temperatures between 800 and 1050 °C. For all temperature conditions, the cross-welded samples failed at a lower critical stress threshold than the simulated HAZ. A finite element model of a 50.8-mm-thick single-V groove weld was used to generate the residual stress maps induced by a 40-pass welding procedure, which in combination with the experimental threshold stress map predicted potential SRC failure locations. Postmortem microstructural evaluations were performed to identify contributing characteristics to SRC. It was found that HAZ samples exhibited a combination of creep void development, secondary cracks with intergranular fracture near grain boundary carbides, and eutectic phases. FZ samples showed brittle fracture with cracks propagating along straight, non-tortuous interdendritic grain boundaries.

Microstructural and mechanical properties of electron beam welded super duplex stainless steel

The electron beam welding of super duplex stainless steels is associated with challenges due to the concentrated heat input and the nitrogen loss that result in a predominantly ferritic structure after the solidification. This study presents an approach to overcome this issue by feeding nickel-based filler wire into the melt pool in welding of 2507 super duplex stainless steel. Results showed that the high-frequency beam oscillation combined with a multi-beam technique led a good mixing between the base metal and the filler wire, even at a large depth-to-width ratio. Additionally, the weld geometry was characterized by near-parallel fusion lines and a narrow heat-affected zone. The nickel addition resulted in a balanced microstructure in the weld metal with ferrite fractions of 35–55 %, despite a significant nitrogen loss, consequently leading to impact energy values of 215 ± 15 J and hardness values of 285 ± 15 HV. The findings of this investigation allow fabricators to effectively design electron beam welding processes for producing thick-walled super duplex stainless steel components.

Laser beam welding of 316L stainless steel to Kovar alloy (UNS K94610) lap joint for a space X-ray counterpart collection device

Laser beam welding of 316L stainless steel to Kovar alloy (UNS K94610) lap joint for a space X-ray counterpart collection device

Distribution and Characteristics of Residual Stresses in Super Duplex Stainless Steel Pipe Weld

This paper explores the distribution and features of residual stresses formed by super duplex stainless steel pipe welding. Experimental investigations, which encompass an elevated temperature tensile test and metallographic observation along with a hardness test and residual stress measurement, were first conducted to obtain the mechanical properties at high base metal temperatures and to confirm whether or not the duplex stainless steel undergoes martensitic phase development during the welding process. Finally, experiments were performed to scrutinize the residual stress evolution through the metallurgical phase transformation in the weld region and its vicinity. A sequentially coupled 3D thermal, mechanical and metallurgical finite element (FE) model capable of incorporating the experimental consequences was established next. A 3D FE simulation of the girth welding process was conducted, and the axial and hoop residual stress profiles along the girth were evaluated. The results substantiate that martensitic phase evolution occurs in the process of cooling during the welding of super duplex stainless steel, and they also highlight the significance of taking the metallurgical phase transformation into account in the numerical reproduction of the girth welding process for the accurate expression of weld-induced residual stresses, which is especially important for precisely predicting hoop residual stresses.