Stable Energy Research Articles

Optimization of Stable Energy PV Systems Using the Internet of Things (IoT)

The modern power grid faces rapid growth in load demand due to industrialization, leading to an unregulated environment and increasing adoption of renewable energy sources, which presents technical challenges, particularly in terms of stability. Hydrogen conversion technology revolutionizes clean electricity storage with renewable energy, and solar hydrogen is now available in autonomous solar systems. The efficiency of solar photovoltaic systems is closely related to using digital electronic maximum peak power tracking (MPPT) technology. The Internet of Things (IoT) is crucial for performance monitoring and real-time control of PV systems, enhancing the understanding of real-time operating parameters. IoT and wireless sensor networks for distributed solar energy devices and joint building design are essential for developing the photovoltaic construction industry. In this paper, the monitoring system that has been proposed offers a potentially effective solution for the intelligent remote and real-time monitoring of solar photovoltaic (PV) systems. It demonstrated a high level of accuracy, reaching 98.49%, and can transmit graphical representations to a smartphone application within a time frame of 52.34 seconds. Consequently, the battery's longevity was extended, energy consumption was diminished, and the quality of service (QoS) for real-time applications inside the Internet of Things (IoT) was enhanced.

Arc erosion behaviors of the densified Ag-SnO2 contact materials containing sub-micron and nano In2O3 additives

The effects of In2O3 additive size on the physical properties and arc erosion behaviors of the densified Ag-SnO2 materials were investigated. Arc resistance mechanism was analyzed based on the microscopic morphology characterization. Results revealed that the physical properties of the Ag-SnO2(In2O3) materials were significantly improved after densification. Relative density and electrical conductivity of the materials reached above 99.5% and 71%IACS, respectively. The densified Ag-SnO2 material containing sub-micron In2O3 showed the low and stable break arc energy. The mass loss of the cathode was dramatically decreased by 65.4%. Importantly, the generation of pores and micro-cracks on the surface of electrodes were significantly restrained and the contact resistance became more stable. By comparison, the nano In2O3 additive less than 100 nm effectively suppressed not only the splash of molten Ag on the surface of cathode but also the aggregation of SnO2 particles on anode. The arc erosion products were obviously decreased, resulting in an enhancement of arc-erosion resistance of Ag-SnO2(nano In2O3) materials. Compared with that without additive, the mass loss of the Ag-SnO2 material which contains nano In2O3 obviously decreased from 2.3 to 1.4 mg. The optimal mass fraction of nano In2O3 in the Ag-SnO2 contact materials was 1 wt%.

Hypothalamic AMP-Activated Protein Kinase as a Whole-Body Energy Sensor and Regulator.

5´-Adenosine monophosphate (AMP)-activated protein kinase (AMPK), a cellular energy sensor, is an essential enzyme that helps cells maintain stable energy levels during metabolic stress. The hypothalamus is pivotal in regulating energy balance within the body. Certain neurons in the hypothalamus are sensitive to fluctuations in food availability and energy stores, triggering adaptive responses to preserve systemic energy equilibrium. AMPK, expressed in these hypothalamic neurons, is instrumental in these regulatory processes. Hypothalamic AMPK activity is modulated by key metabolic hormones. Anorexigenic hormones, including leptin, insulin, and glucagon-like peptide 1, suppress hypothalamic AMPK activity, whereas the hunger hormone ghrelin activates it. These hormonal influences on hypothalamic AMPK activity are central to their roles in controlling food consumption and energy expenditure. Additionally, hypothalamic AMPK activity responds to variations in glucose concentrations. It becomes active during hypoglycemia but is deactivated when glucose is introduced directly into the hypothalamus. These shifts in AMPK activity within hypothalamic neurons are critical for maintaining glucose balance. Considering the vital function of hypothalamic AMPK in the regulation of overall energy and glucose balance, developing chemical agents that target the hypothalamus to modulate AMPK activity presents a promising therapeutic approach for metabolic conditions such as obesity and type 2 diabetes mellitus.

Chemically tailored biomass sponge-based hierarchical porous carbon for superior solar thermal energy harvesting and stable thermal energy storage/release

In the past work, almost all biomass sponge-based hierarchical porous carbons are tried to preserve the original 3D porous structure as much as possible, thus restricting their effectiveness in thermal energy utilization. In current work, loofah sponge-based hierarchical porous carbon covering nanometer to micrometer was fabricated through a crosslinking-carbonization-etching chemically tailored process. The re-constructed hierarchical porous carbons (LHPCs) have totally different characteristics from that depending on original 3D pores. The LHPC-based composite phase change materials (PCMs) exhibited the maximum melting/solidifying latent heat of 155.1/158.7 J g−1 and exceptional thermal reliability. The optimal solar-thermal converting efficiency of the composite PCMs topped 95 %, higher than some expensive carbon-based materials. Compared to previously reported work, the fabricated composite PCMs showed improved thermal energy storage/release capability and solar-heat conversion efficiency. Additionally, the regulation of about 6.3 °C for composite PCMs was achieved in a hut test. This work has further advanced a superior porous carbon-tailored strategy compared to the traditional approach, building upon the original 3D porous structure.

Ultrashort large-bandwidth X-ray free-electron laser generation with a dielectric-lined waveguide.

Large-bandwidth pulses produced by cutting-edge X-ray free-electron lasers (FELs) are of great importance in research fields like material science and biology. In this paper, a new method to generate high-power ultrashort FEL pulses with tunable spectral bandwidth with spectral coherence using a dielectric-lined waveguide without interfering operation of linacs is proposed. By exploiting the passive and dephasingless wakefield at terahertz frequency excited by the beam, stable energy modulation can be achieved in the electron beam and large-bandwidth high-intensity soft X-ray radiation can be generated. Three-dimensional start-to-end simulations have been carried out and the results show that coherent radiation pulses with duration of a few femtoseconds and bandwidths ranging from 1.01% to 2.16% can be achieved by changing the undulator taper profile.

Irreversible bonds for higher stability of COF materials in photocatalytic reactions

Covalent organic frameworks (COFs), one of a multitude of advanced mainstream materials in photocatalysts, are crystalline porous materials with tunable topology and high porosity and are connected by dynamic covalent bonds. We sought to achieve efficient photocatalytic yields, making the stability of the bond energy crucial. Stable bond energy will enable our products to be more economically efficient. At present, the main photocatalysts are reversible imine bonds and other 2D COFs, but irreversibly stable COFs are seldom involved. Therefore, this review surveys the relevant literature to explore the stability of irreversible bond energy, elaborating the synthesis schemes of irreversible bonds. Irreversibly connected bonds will improve the stability and durability of our synthesized catalyst in practical applications, so we seek to explore the stability of bond energy for our practical applications. In this review, we offer a detailed summary of the irreversible bonding pattern, explore the stability of COFs, and summarize classic highly crystalline ordered semiconductor COFs with irreversible bonding methods.

Trends in the development of EU energy policy at the present stage

The issue of energy security and energy independence of the EU is one of the key factors in ensuring the stable development of the association. The subject of the study is the energy concepts of the European Union. The object of the study is the modern energy policy of the EU countries. The countries of the European Union are among the world's largest importers and exporters of energy resources, and therefore one of the criteria for EU energy security is the creation of secure logistics chains for uninterrupted energy supplies, since this factor has always been one of the most important problems in energy security. However, despite all the data that the European Union has, this area is a source of numerous problems for ensuring energy security that the EU faces at the current stage of its development. The methodological basis of the study is a systematic analysis and a geo-economic approach. The systematic approach was used in the work to identify the reasons for the transformation of EU energy concepts in the context of the energy crisis. The geo-economic approach allows us to qualitatively consider this issue from the point of view of economics and geopolitics of the countries of Eastern and Western Europe in the context of energy transition. The novelty of the research lies in the comprehensive analysis of the concept of energy security in the complex in the context of energy transfer. The authors pay special attention to the analysis of the energy policy of the European Union, numerous new initiatives and documents related to this area, as well as the development of the concept of green energy. The authors highlight the challenges that the EU will face on the way to building a stable and safe energy sector. The paper also examines the impact of the EU's energy policy on the concept of European unity. Attention is being paid to the EU's attempts to diversify energy supplies, which plays an important role in the context of the Ukrainian crisis and complications from the loss of Russian supplies. The authors conclude that the lack of internal unity within the EU does not allow for an effective and sustainable energy policy, since the European Union does not have a common energy legislation, and infrastructure development between the countries of Western and Eastern Europe is overly diversified, which does not allow us to talk about the transformation of energy policy in the EU countries at the present stage.

Investigation of role of fins in a Francis turbine model's cavitation-induced instabilities under design and off-design conditions

Harnessing hydraulic energy for power generation using Francis turbines presents formidable downstream swirl instabilities, which can lead to pressure surges at part load (PL) conditions. Cavitation-induced issues affect not just the PL operations but also the power generation at the best efficiency point (BEP). To combat these challenges, fins strategically placed on the draft tube (DT) periphery aid in low-pressure recovery, which suppresses the hurdles for stable energy extraction. This ongoing study delves deep into the internal flow dynamics of the turbine, considering various Thoma numbers, and evaluating the impact of fins. The investigation employs numerical simulations utilizing structured and unstructured grids, incorporating the Shear Stress Transport (SST) model and the Rayleigh-Plesset model to model turbulent flow in a two-phase mixture. Preliminary findings reveal that at PL, the presence of fins substantially reduces low-pressure zone formation, minimizing vortex ropes and associated instabilities. The fins positively influence axial velocity, reducing swirl intensity and mitigating pressure pulsations by 60 % at PL. Conversely, at the BEP, the impact of fins appears less pronounced, with zero detrimental effect. In conclusion, with no negative effect at BEP, the incorporation of fins enhances the turbine's operational range and ensures smoother and more stable energy production at PL.

Diagnosis of the Development of Energy Cooperatives in Poland—A Case Study of a Renewable Energy Cooperative in the Upper Silesian Region

Renewable energy sources (RESs) offer key transformative potential from a societal point of view due to their modularity and ability to generate energy at the local level, allowing for the development of grassroots democratic and participatory initiatives. The paper aims to share insights into the processes of creating RES cooperatives in Poland. One of the first cooperatives to be established in the Upper Silesian region in Poland was the energy cooperative (EC) “Our Energy”. This study presents an in-depth empirical analysis of a community-based renewable energy cooperative. The study employed a case study methodology, including a SWOT analysis framework, to describe the research subject and identify its strengths, weaknesses, opportunities, and threats. Key findings indicate that members benefit from stable energy prices and full recovery of the energy produced, and the cooperative is at the forefront of energy-sharing practices that minimize costs through direct transactions with the local municipality. The strategic goals of the EC focus on expanding membership, increasing the number of photovoltaic installations, implementing energy balancing, combating energy poverty, and reducing emissions. Challenges such as financial constraints and a lack of real-time monitoring of energy distribution are acknowledged, and carbon footprint reduction innovations and stakeholder engagement are highlighted as forward-looking approaches. The study highlights the role of cooperatives as a model for community-led sustainable energy initiatives. However, the study acknowledges the limitations of its small sample size, suggesting the need for broader research to understand the impact of collaborative energy on decarbonization. Future research directions are proposed, focusing on the long-term sustainability and socioeconomic impacts of energy cooperatives. This study contributes to the scholarly discourse on renewable energy cooperatives by offering insight into their potential to bridge the gap between energy producers and consumers and support sustainable community development. The main novelty of this paper lies in its detailed examination of a specific renewable energy cooperative, incorporating SWOT analysis, stakeholder perspectives, quantitative assessments, and a forward-thinking approach. This multifaceted analysis contributes to the existing literature on renewable energy initiatives, providing a valuable reference for researchers, policymakers, and practitioners in the field.

Recent Advances in Bridge-Less Power Factor Correction Converter

Power Factor Corrector (PFC) is a device used in electrical systems to improve power efficiency by reducing reactive power and harmonics, resulting in a higher power factor and reduced energy consumption. It enhances the utilization of electrical networks and minimizes wastage of power resources.This paper reviews the current research on the new bridge-less PFC converter, firstly comparing and analyzing seven configurations and control strategies of traditional Boost, bridge-less Boost, bi-directional switched bridge-less Boost, Pseudo totem bridge-less Boost, dual diode bridge-less Boost, and five-level flying across capacitor bridge-less, and then discussing the characteristics of the bridge-less PFC based on the practical application of the GaN power device. Through the study of bridge-less PFC converter, this paper discusses its advantages and applications in depth, and provides technical support for the realization of high-efficiency, stable and sustainable energy conversion, so as to better promote the development of the energy field.

Environmental Assessment of Hydrothermal Treatment of Wet Bio-Residues from Forest-Based and Agro-Industries into Intermediate Bioenergy Carriers

Hydrothermal carbonization (HTC) of low quality, wet biogenic residues into intermediate bioenergy carriers can potentially contribute to a more flexible and stable renewable energy system and reduce environmental impacts compared to current residue disposal practices. This study quantifies the environmental impacts via life cycle assessment (LCA) of a novel hydrothermal process for the treatment on an industrial scale of application of three wet biogenic residues (paper bio-sludge, olive pomace, and orange peel) into bioenergy carriers, i.e., solid pellets and biogas. A comprehensive attributional cradle-to-gate life cycle assessment (LCA) was conducted; the life cycle impact assessment (LCIA) utilised the ReCiPe impact assessment method. A selection of 10 significant impact categories was prioritised. Reliability of this categorization was also ensured through a sensitivity analysis carried out using Monte Carlo simulation. Climate change, particulate matter formation and terrestrial acidification impact categories showed the highest reliability, while for freshwater ecotoxicity and freshwater eutrophication impact categories in the study suggest the need for more robust data and further investigation. The climate change impact category presents the following values, as kg CO2eq/tresidue: pulp and paper bio-sludge (PPB), 17.9; olive pomace (OP), −1290; orange peel (ORP), −1301. The LCA study compared electricity yields of the hydrothermal treatment process with conventional treatment processes for each of the target residue streams. The environmental performance of the proposed hydrothermal treatment benefits significantly from the combination of intermediate bioenergy carriers (pellets) from the solid fraction with biogas production from the liquid fraction. Avoided emissions due to the heat recovery provide further environmental benefits. The LCIA results show that the carbon footprint of the F-CUBED production system, as kgCO2eq/kWhe, accounts for –4.56, −0.63, and −0.25 for paper bio-sludge, olive pomace and orange peel, respectively.

Towards energy sustainability: Exploring the nexus between global value chain participation and energy security in developing and developed countries.

International trade has a significant impact on global environmental quality and sustainable economic development. Global value chains (GVCs) have become a crucial component of international trade and development policy. The global production structure has become more complicated with the inclusion of domestic markets in GVC, putting significant pressure on world energy resources and environmental sustainability. Therefore, traditional trade measures no longer accurately reflect how global trade affects the energy security of developing and developed countries. Thus, this study is the first to use a panel-corrected standard error method to look at the relationship between GVC participation and energy security by using a global sample of 35 developed and 27 developing nations from 1995 to 2018. A feasible generalized least squares model was also applied to confirm the robustness of the model. Six indicators-foreign direct investment, industrialization level, capital formation, human capital index, political stability, and GVC-were used in this research to look at their impact on the four fundamental pillars of energy security (availability, applicability, sustainability, and affordability) for sustainable economic development. For developed countries, it was confirmed that there is a non-linear relationship between GVC participation and energy intensity, renewable energy consumption, and non-fossil fuel use. In the case of developing countries, the non-linear relationship in terms of all aspects of energy security was also confirmed. The findings also indicated that GVC's involvement benefits all four dimensions of energy security in both developing and developed countries once it reaches a certain threshold. Our findings further support the impacts of long-term cointegration between GVC and energy security for sustainable economic development. Therefore, the nations must promote technology transfer and capacity building within GVCs for inclusive energy security. Similarly, they may foster sustainable practices through collaborative governance for a stable global energy network by acknowledging the positive impact of income levels on energy security.

Enhanced Electrocatalytic Conversion of Nitrates to Ammonia: Fuel from Waste.

Ammonia (NH3) is globally one of the most produced chemicals. Despite being known for its use as a fuel and as a precursor of multiple chemicals, during its production, it is responsible for more than 1.2 % of the total global CO2 emission and consumes a large amount of energy. In this work, we studied a flow-through membrane-free electrocatalytic device (CMED) to produce continuous stream of NH3 from a common water contaminant, nitrate (NO3 -). Indium-palladium (In-Pd) nanoparticles were impregnated in activated carbon cloth (ACC) and used as a cathode in the electrochemical device. It is found that in the counter electrode, adding oxygen evolution reaction (OER) active catalysts like platinum (Pt) for the regeneration of hydrogen ions enhances the rate of ammonia conversion to 7.28 μmol min-1 cm-2, eliminate the production of toxic nitrite by-products, as well as provide a platform for a stable energy consumption over long periods of time. This method for the conversion of NO3 - into NH3 promises a way forward for sustainable resource utilization while generating fuel from waste and contributing to future circular economies, and managing the nitrogen cycle in water that is a major challenge of the 21st century society.

Pseudocapacitance behavior enables efficient and stable electrochemical energy conversion and storage in glucose/air enzymatic biofuel cells

Constructing an integrated system with high-efficiency and stable energy conversion and storage (ECS) is of great significance but remains challenges. Herein, we report a biodevice consisting of a bioanode of tetrathiafulvalene/glucose oxidase (TTF/GOx) immobilized on asphalt-derived porous carbon (APC) for catalyzing glucose oxidation and a biocathode of 2,2’-azinobis(3-ethylbenzothiazoline-6-sulfonate)/bilirubin oxidase (ABTS/BOD) immobilized on APC for catalyzing oxygen reduction, to achieve ECS with high-efficiency and excellent stability. The redox mediators, TTF and ABTS, used at the bioanode and biocathode, respectively, simultaneously mediate electron transfer to release electric current on discharging and serve as pseudocapacitors to achieve charge storage at open-circuit conditions, enabling high power density and self-charge capability. The biodevice of the above configuration delivers a peak power output of 5.01 mW cm−2 in the pulse discharge mode with cell voltage remaining 93.7 % of its initial value after 100 pulse discharge/self-charge cycles. This work provides a highly efficient solution to address the low power density and poor stability of the conventional enzymatic biofuel cells, showing great implications for small, implantable and wearable electronics.

Improvement effects of knee-bracing friction dampers on cyclic behavior of steel joints in antique buildings

To inherit the unique characteristics of historical timber architecture, the steel antique building (SAB) imitating ancient Chinese timber structures has been constructed using contemporary steel materials and fabrication techniques. These buildings typically exhibit premature yielding cracks and weak energy dissipation at the beam ends under seismic loads. To improve the seismic performance of SABs, two different types of friction dampers were deployed at the knee-bracing region around beam-column joints in SABs. First, cyclic loading tests on dampers indicate that both shear friction dampers and rotational friction dampers exhibit full hysteretic behavior, demonstrating an excellent and stable energy dissipation capacity. The friction coefficient of dampers with brass pads was theoretically calculated to be 0.35. Second, the quasi-static test showed that failure of steel joint specimens with knee-bracing dampers primarily occurred at replaceable angles in the beam-column connection region, which demonstrates that the repairability of steel joints in SABs can be greatly improved without overcomplicated labor. Adding knee-bracing dampers effectively postpones damage to the replaceable angles, which improves the strength, stiffness, and energy dissipation capacity of the steel joints significantly. The shear damper exhibits a more pronounced improvement in the overall structural seismic performance compared to the rotational damper with the same frictional sliding force. Moreover, numerical simulations showed that the strength of the proposed joints with knee-bracing friction dampers decreases with an increase in the axial compression ratio, while increasing the thickness of angles or the sliding force of dampers can effectively improve the seismic performance of the steel joints in SABs.

Emerging Nanomaterials toward Uranium Extraction from Seawater: Recent Advances and Perspectives.

Nuclear energy holds great potential to facilitate the global energy transition and alleviate the increasing environmental issues due to its high energy density, stable energy output, and carbon-free emission merits. Despite being limited by the insufficient terrestrial uranium reserves, uranium extraction from seawater (UES) can offset the gap. However, the low uranium concentration, the complicated uranium speciation, the competitive metal ions, and the inevitable marine interference remarkably affect the kinetics, capacity, selectivity, and sustainability of UES materials. To date, massive efforts have been made with varying degrees of success to pursue a desirable UES performance on various nanomaterials. Nevertheless, comprehensive and systematic coverage and discussion on the emerging UES materials presenting the fast-growing progress of this field is still lacking. This review thus challenges this position and emphatically focuses on this topic covering the current mainstream UES technologies with the emerging UES materials. Specifically, this review elucidates the causality between the physiochemical properties of UES materials induced by the intellectual design strategies and the UES performances and further dissects the relationships of materials-properties-activities and the corresponding mechanisms in depth. This review is envisaged to inspire innovative ideas and bring technical solutions for developing technically and economically viable UES materials.

Research on Residual-Current Measurement System of Substation Considering Magnetic Shielding Effect.

Residual current is an important monitoring quantity of a power system, and a current sensor plays an important role in detecting current. The substation environment is complex. In addition to the power frequency signal, residual current also has AC and DC components. But it is also affected by the stray magnetic field of the substation. Therefore, the accuracy of the current sensor demands higher requirements. The tunnel magnetoresistive sensor has the advantages of a stable operation, high efficiency, and energy saving, but it is easily affected by the external stray magnetic field during measurements, resulting in a large error. Therefore, this paper proposes a residual-current sensing monitoring system considering the magnetic shielding effect. The root mean square error of the magnetic shielding structure is only 0.572 mA, which can effectively reduce the influence of the external magnetic field and improve the detection accuracy. At the same time, the DC measurement error is less than 1%, the AC measurement error is less than 5%, and the hybrid AC/DC error is less than 8%. It has good response ability and can accurately detect residual current.

Charged Particles Orbiting Charged Black-Bounce Black Holes

The detailed and comprehensive analysis of radiation processes in accretion disks consisting of electrically charged particles around black holes may provide powerful information about the spacetime geometry of the central black hole. We investigate the circular orbits of electrically charged particles around an electrically charged black-bounce Reissner–Nordström (RN) black hole, known as an RN Simpson–Visser (SV) black hole. We also study the profiles of the innermost stable circular orbits (ISCOs), energy, and angular momentum of the particles in their ISCOs, as well as the efficiency of energy release processes in the accretion disk in the Novikov–Thorne model. Finally, we calculate and study the effects of the black-bounce parameter as well as the black-hole charge on the intensity of the radiation of ultrarelativistic charged particles orbiting the charged RN SV black hole along circular orbits and falling into the black hole. It is observed that the black-bounce parameter essentially decreases the ISCO radius, and consequently the energy extraction and intensity of electromagnetic radiation.

Polyethylene glycol-impregnated carbon quantum dots-phenolic phase change composites for highly efficient thermal energy storage

The development of stable smart thermal energy storage systems is the key to reaching breakthroughs in thermal management technologies based on phase change composites (PCC). In this study, high-performance PCC is developed by impregnating polyethylene glycol (PEG), as a polymeric phase change material (PCM), into the porous structure of modified resorcinol-formaldehyde (RF) hydrogels. Carbon quantum dots (CQDs) and 3-chlorophenol are introduced into the RF structure during the synthesis process to increase energy storage properties and impregnation efficiency. A sol-gel polymerization method is used to synthesize the hydrogels, followed by the impregnation of liquid PEG600 into the hydrogel structure. The low PEG leakage of optimal PCC consisting of 3-chlorophenol and 0.2 wt% CQDs is related to the presence of surface functional groups in the structure of the modified RF hydrogels resulting in the formation of hydrogen bonding and electrostatic forces. The melting enthalpy of the optimal PCC is 67 % higher than the unmodified RF-based PCC, while the encapsulation efficiency is 92.5 %. Our results confirm that thermal energy storage performance can be improved by 40 % through the addition of CQDs and 3-chlorophenol into the polymeric material. These PCC systems show long-term stability in terms of storage/release cycles and have the potential to be used as thermal regulator systems.

Cryptographic triboelectric random number generator with gentle breezes of an entropy source.

A wind-driven triboelectric nanogenerator (W-TENG) is a promising energy harvesting device due to its clean, ubiquitous and unexhausted properties. In addition, a W-TENG induces unpredictable chaotic outputs from wind flow that can serve as an entropy source for cryptography. This can be applied to a true random number generator (TRNG) for a secured system due to its inherent turbulent nature; thus, a W-TENG with a two-in-one structure can simultaneously generate both power and true random numbers. However, a previously reported W-TENG had one major drawback: a wind velocity of 10m/s is required for stable energy harvesting by wind force. Thus, it is timely to demonstrate a W-TENG-based RNG whose operating condition is below 3m/s, which is a gentle breeze similar to natural wind. In this study, we demonstrate a wind-driven cryptographic triboelectric random number generator (WCT-RNG) by using a W-TENG whose operating condition for wind speed is below 3m/s by adopting a rear-fixed film structure instead of a conventional structure. The rear-fixed film refers to the fluttering film being freestanding on the front-side and fixed on the rear-side, where the front- and rear-sides are the wind inlet and outlet, respectively. The WCT-RNG enables the W-TENG to operate below a 3m/s wind velocity. Because of this, the working time of the WCT-RNG is dramatically enhanced from only 8-42% at an average altitude above sea level. As the capability of operating at low wind speeds is significantly improved, a WCT-RNG becomes more useful and practical for generating both power and true random numbers in a single device. The device can thereby lead to the construction of a self-powered TRNG and secure communication for Internet of Things (IoT) devices in various environments, even under a gentle breeze. In this study, we explain the design of a WCT-RNG structure and also evaluate its randomness by using an NIST SP 800-22 B test suite with a reliability test.