Stability Properties Research Articles

Fabrication and efficacy assessment of combination of brimonidine and ivermectin for treatment of papulopustular rosacea.

Rosacea is a chronic inflammatory, multifactorial disease for which combination therapy could be an effective treatment. In this study, we evaluate the effect of the combination therapy of brimonidine 0.33% and ivermectin 1% as a single cream for the treatment of papulopustular rosacea. A stable and appropriate formulation was prepared by adding the aqueous phase to the lipid phase while being stirred. The stability and physicochemical properties of the formulation were evaluated under accelerated conditions. Twelve patients (36-60 years) with mild to moderate papulopustular rosacea and a Demodex count of five or more were treated with the combination of brimonidine 0.33% and ivermectin 1% cream. Clinician's Erythema Assessment (CEA), Patients Self-Assessment (PSA), skin erythema (ΔE) and lightness (ΔL), and skin biophysical parameters including transepidermal water loss (TEWL), skin hydration, pH, and sebum content, as well as erythema and melanin index and ultrasound parameters, were measured before treatment and 4 and 8 weeks after. Adverse drug reactions were also recorded. CEA and PSA decreased significantly from 3 to 2 after 8 weeks, respectively (p-value = 0.014 for CEA and 0.010 for PSA). ΔE and ΔL, as well as skin erythema index and TEWL improved after 8 weeks of treatment (p < 0.05). Two patients withdrew from the study in the first week because of local adverse effects; one developed flushing following treatment and left the investigation after 4 weeks and another patient withdrew from the study after 4 weeks due to deciding to become pregnant. Eight-week treatment with the combination of brimonidine 0.33% and ivermectin 1% was shown to be effective for improvement of erythema and inflammatory lesions in mild to moderate papulopustular rosacea.

Synthesis and Characterization of Maghemite Nanoparticles Functionalized with Poly(Sodium 4-Styrene Sulfonate) Saloplastic and Its Acute Ecotoxicological Impact on the Cladoceran Daphnia magna.

Using a modified co-precipitation method, 11(2) nm γ-Fe2O3 nanoparticles functionalized with PSSNa [Poly(sodium 4-styrenesulfonate)] saloplastic polymer were successfully synthesized, and their structural, vibrational, electronic, thermal, colloidal, hyperfine, and magnetic properties were systematically studied using various analytic techniques. The results showed that the functionalized γ-Fe2O3/PSSNa nanohybrid has physicochemical properties that allow it to be applied in the magnetic remediation process of water. Before being applied as a nanoadsorbent in real water treatment, a short-term acute assay was developed and standardized using a Daphnia magna biomarker. The ecotoxicological tests indicated that the different concentrations of the functionalized nanohybrid may affect the mortality of the Daphnia magna population during the first 24 h of exposure. A lethal concentration of 533(5) mg L-1 was found. At high concentrations, morphological changes were also seen in the body, heart, and antenna. Therefore, these results suggested the presence of alterations in normal growth and swimming skills. The main changes observed in the D. magna features were basically caused by the PSSNa polymer due to its highly stable colloidal properties (zeta potential > -30 mV) that permit a direct and constant interaction with the Daphnia magna neonates.

Achieving ultrahigh energy density and efficiency simultaneously in (Na, K)NbO3-based lead-free relaxor ferroelectrics via a collaborative design

Relaxor ferroelectrics have garnered enormous attention for their great application potential in pulsed power energy-storage capacitors, while simultaneously achieving large recoverable energy density (Wrec) and high efficiency (η) remains a formidable challenge. Through collaboratively controlling multiscale structure via a combination of composition design and processing improvement, polar nanodomains with multiple local symmetries were engineered in ultrafine grains, enabling significantly reduced polarization hysteresis, delayed saturation polarization, maintained high polarization, and enhanced breakdown strength. As a result, an excellent comprehensive energy-storage performance of Wrec ∼11.8 J/cm3 and η ∼88.7 % is achieved in the (Na, K)NbO3-based spark-plasma-sintered lead-free ceramics, together with stable charge-discharge properties of power density ∼176.3 MW/cm3, discharge energy density ∼3.2 J/cm3, and discharge time ∼43 ns over a wide temperature range of 20–140 °C. The studied ceramic demonstrates great advantages in advanced capacitive energy-storage applications.

The Effect of Antibacterial-Osteogenic Surface Modification on the Osseointegration of Titanium Implants: A Static and Dynamic Strategy.

Titanium (Ti) and its alloys are widely used biomaterials in bone repair. Although these biomaterials possess stable properties and good biocompatibility, the high elastic modulus and low surface activity of Ti implants have often been associated with infection, inflammation, and poor osteogenesis. Therefore, there is an urgent need to modify the surface of Ti implants, where changes in surface morphology or coatings loading can confer specific functions to help them adapt to the osseointegration formation phase and resist bacterial infection. This can further ensure a healthy microenvironment for bone regeneration as well as the promotion of immunomodulation, angiogenesis, and osteogenesis. Therefore, in this review, we evaluated various functional Ti implants after surface modification, both in terms of static modifications and dynamic response strategies, mainly focusing on the synergistic effects of antimicrobial activities and functionalized osteogenic. Finally, the current challenges and future perspectives are summarized to provide innovative and effective solutions for osseointegration and bone defect repair.

The Role of Oxygen Vacancies in Phase Transition and the Optical Absorption Properties within Nanocrystalline ZrO2.

Zirconia (ZrO2) nanoparticles were synthesized using a solvothermal method under varying synthesis conditions, namely acidic, neutral, and alkaline. X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) were leveraged to investigate the phase evolution and topographical features in detail. The resulting crystal phase structures and grain sizes exhibited substantial variation based on these conditions. Notably, the acidic condition fostered a monoclinic phase in ZrO2, while the alkaline condition yielded a combination of tetragonal and monoclinic phases. In contrast, ZrO2 obtained under neutral conditions demonstrated a refinement in grain sizes, constrained within a 1 nm scale upon an 800 °C thermal treatment. This was accompanied by an important transformation from a monoclinic phase to tetragonal phase in the ZrO2. Furthermore, a rigorous examination of XPS data and a UV-visible spectrometer (UV-vis) analysis revealed the significant role of oxygen vacancies in phase stabilization. The notable emergence of new energy bands in ZrO2, in stark contrast to the intrinsic bands observed in a pure monoclinic sample, are attributed to these oxygen vacancies. This research offers valuable insights into the novel energy bands, phase stability, and optical absorption properties influenced by oxygen vacancies in ZrO2. Moreover, it proposes an innovative energy level model for zirconia, underpinning its applicability in diverse technological areas.

Innovative Treatment of Ancient Architectural Wood Using Polyvinyl Alcohol and Methyltrimethoxysilane for Improved Waterproofing, Dimensional Stability, and Self-Cleaning Properties

This study introduced a novel two-step treatment to enhance the waterproofing, dimensional stability, and self-cleaning capabilities of ancient architectural wood. The process was initiated with the immersion of wood in an organic hybrid sol, composed of an acidic methyltrimethoxysilane (MTMS)-based silica sol and polyvinyl alcohol (PVA), which effectively sealed the wood’s inherent pores and cracks to mitigate degradation effects caused by aging, fungi, and insects. Subsequently, the treated wood surface was modified with an alkaline MTMS-based silica sol to form a functional superhydrophobic protective layer. The modification effectiveness was meticulously analyzed using advanced characterization techniques, including scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), Fourier-transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). The results demonstrated substantial improvements: the modified wood’s water contact angle (WCA) reached 156.0°, and the sliding angle (SA) was 6.0°. Additionally, the modified wood showed a notable reduction in water uptake and moisture absorption, enhancing its dimensional stability. The superhydrophobic surface endowed the wood with excellent self-cleaning properties and robust resistance to pollution. Enhanced mechanical durability of superhydrophobic surface was observed under rigorous testing conditions, including sandpaper abrasion and tape peeling. Furthermore, the modification improved the thermal stability, compressive strength, and storage modulus of the wood. Collectively, these enhancements render this modification a potent methodology for the preservation and functional augmentation of historic architectural woodwork.

Polyvinyl alcohol-based multifunctional hydrogel film: a novel strategy for food preservation packaging

Food spoilage leads to the annual huge wastage of food. There is a pressing need for safe, multifunctional food preservation packaging to curb this wastage and prevent contamination. In this study, we present a novel, cross-linked P-GL hydrogel film with a smooth surface microstructure, derived from polyvinyl alcohol (PVA), gallic acid (GA), and lysozyme (L). This hydrogel film serves as an exceptional packaging material for food preservation, displaying an ability to completely block UV light and efficiently impede the penetration of water vapor and O2. Remarkably, the P-GL hydrogel film exhibits a fracture strength of approximately 37.9 MPa, demonstrating superior water solubility, thermal stability, and mechanical properties. Also, this P-GL hydrogel film can effectively eliminate E. coli and S. aureus. The P-GL hydrogel film has proven to be successful in mitigating the spoilage of blueberries through coating and covering treatments, outperforming commercial plastic wrap. As a result, the shelf life of blueberries can be extended to 20 days. Our work provides innovative insights that could potentially drive the use of safe and multifunctional hydrogel films in the food preservation packaging industry.

Co-Optimization of a-InGaZnO Framework for Enhancing Thin Film Transistors Stability and Electrical Properties

Co-Optimization of a-InGaZnO Framework for Enhancing Thin Film Transistors Stability and Electrical Properties

Study on environmental characteristics of sustainable biomimetic soil preparation and its application in gangue reclamation

To address the key challenges in achieving large-scale ecological reclamation of coal gangue in situ, this study utilized loess from a mining area in Northwest China to prepare a biomimetic soil. A new inorganic curing agent (ISA) was developed using coal-based solid waste and cement. The study investigates the influence of different ISA dosages and their interaction with Polyacrylamide (PAM) on the environmental characteristics of biomimetic soil, including geotechnical, ecological, and heavy metal stabilization properties. Results indicate that the addition of ISA significantly enhanced the geotechnical performance of the in-situ soil, with unconfined compressive strength exceeding 350 kPa when ISA content was above 6 %. Soil evaporation experiments and soil water characteristic curve tests demonstrated that a 6 % ISA dosage combined with 0.05 ‰ PAM could maintain soil's good water retention capability while preserving a bimodal pore structure. The biomimetic soil exhibited effective stabilization of heavy metals, including Pb, Zn, Cu, and As. The particles of PAM and the hydration products of ISA not only filled soil pores and increased soil strength but also adsorbed, encapsulated, and immobilized heavy metals. “Biomimetic soil-gangue” leaching test results confirmed that the gangue samples treated with biomimetic soil met the standards for Class III underground water in China regarding heavy metal leaching values. This study provides an effective solution for the large-scale in-situ disposal and resource utilization of gangue in Northwestern mining areas of China.

Facile production of graphene-based ternary composite coatings on metallic bipolar plates

Graphene-based composite coatings can be applied on metallic bipolar plates (BPs) of PEMFC for corrosion protection and electron conduction, benefited from the high electrical conductivity, chemical stability and physical barrier properties of graphene. To reach the high electrical conductivity requirement, the composite coatings shall have high graphene content, which brings challenges including dispersion, processability and interface compatibility. In this work, polyisocyanate was grafted on graphene surfaces to enhance the compatibility with polyurethane (PU). Carbon black was introduced as conductive bridging, which filled in defects of graphene/PU coatings. The corrosion current density of the ternary composite coatings with 60 % functionalized graphene, 30 % PU and 10 % carbon black was 0.43 μA·cm−2 in H2SO4 solution of pH 3 at 80 °C, while the interfacial contact resistance was 6.75 mΩ·cm2 and the in-plane conductivity was 137.4 S·cm−1. The composite coatings provided an efficient and cost-effective solution for up-scaling production of metallic BPs.

Development of piperine nanoparticles stabilized by OSA modified starch through wet-media milling technique with enhanced anti-adipogenic effect in 3T3-L1 adipocytes

Piperine (PIP) has been known for its pharmacological activities with low water solubility and poor dissolution, which limits its nutritional application. The purpose of this research was to enhance PIP stability, dispersibility and biological activity by preparing PIP nanoparticles using the wet-media milling approach combined with nanosuspension solidification methods of spray/freeze drying. Octenyl succinic anhydride (OSA)-modified waxy maize starch was applied as the stabilizer to suppress aggregation of PIP nanoparticles. The particle size, redispersibility, storage stability and in vitro release behavior of PIP nanoparticles were measured. The regulating effect on adipocyte differentiation was evaluated using 3T3-L1 cell model. Results showed that PIP nanoparticles had a reduced particle size of 60 ± 1 nm, increased release rate in the simulated gastric (SGF) and intestinal fluids (SIF) and enhanced inhibition effect on adipogenesis in 3T3-L1 cells compared with free PIP, indicating that PIP-loaded nanoparticles with improved stability and anti-adipogenic property were developed successfully by combining wet-media milling and drying methods.

Microstructural stability and mechanical property of AlCrFeMoTi high-entropy amorphous alloy thin films under He+ ions irradiation

High-entropy amorphous materials have recently proved exceptional radiation resistance, showing potential as a candidate materials for nuclear industry applications. This study synthesized nearly equi-atomic AlCrFeMoTi high-entropy amorphous thin films with a thickness of about 499 nm using magnetron sputtering. The prepared films were subjected to low dose, 0.5 MeV He+ ion irradiation, with varying irradiation damage ranging from 0.01 to 0.1 displacement per atom (dpa). Increasing the irradiation dose led to a decrease in the radius of the inner diffraction halo (r) and an increase in the crystal-like order, indicating an irradiation-induced structural relaxation process within the amorphous matrix. This relaxation results in more efficient atomic packing, yielding a denser amorphous structure and enhanced hardness of AlCrFeMoTi high-entropy amorphous thin films. This study demonstrates that AlCrFeMoTi high-entropy amorphous thin films exhibit remarkable radiation resistance, with stable microstructure and mechanical properties under He+ irradiation, making them promising candidates for applications in the nuclear industry.

Ultrasensitive plasmonic biosensor based on metal/porous graphene/perovskite multilayers

Perovskite compounds including sesquioxide materials have recently gained popularity in optical biosensing due to their high chemical stability and excellent semiconducting properties. These properties make perovskite materials an ideal platform for optical detection. In this line, this paper presents new real-time ultrasensitive plasmonic biosensor for large molecule detection based on metal/porous graphene/perovskite material (MPGP). The performance of the proposed device is reported in terms of the variety of perovskite media such as In2O3 and BaSnO3 materials and the nature of pores incorporated in the multilayer graphene which plays the role of amplifier medium. It is observed that the sensitivity of this device increases from 684nm/RIU using BaSnO3 to 948nm/RIU using sesquioxide In2O3. Whereas the quality factor reaches the maximum value Q = 74.5 for the porosity P = 7 % with BaSnO3 while Q = 9275 for (P = 28 %) with In2O3. However, the limit of detection is around 6 μM. Moreover, the proposed device exhibits an optical sensing region that can be adjusted by varying their electrical and geometrical parameters to meet the requirements of desired molecule detection.

Self-powered triboelectric sensor based on a carbon fiber/glass fiber/epoxy structural composite for efficient traffic monitoring

Intelligent transportation systems (ITSs) are being investigated as potential solutions for traffic congestion. Triboelectric sensors (TESs) have gained prominence among ITS technologies owing to their efficiency and self-powered capabilities in detecting external changes through friction-generated electrical signals. Herein, a traffic monitoring system using a fiber-reinforced plastic-based TES (FRP-TES) is proposed, designed with high-strength and high-stiffness fiber-reinforced plastic (FRP) as the core material. FRP is a structural composite comprising high-strength fibers impregnated with engineering resin. When the surface of the epoxy, which has a charged layer, reacts with the charged tire, electrostatic induction occurs in the carbon fibers. By leveraging the principles of carbon and glass fiber/epoxy-reinforced infrastructure, along with corresponding electrical properties, we analyze electrical signals produced when a tire traverses the FRP-TES. We subject the FRP-TES to electrical durability and tensile tests to verify signal stability and mechanical properties (strength ≤ 1770.87 MPa, modulus ≤ 41.38 GPa). The analysis proposes an effective method for obtaining the tire position, movement direction, speed, and acceleration using paired FRP-TES units. The proposed approach achieves significant reduction in maximum errors (0.52 % in speed, 3.24 % in acceleration) with eight evenly spaced FRP-TES units in a 240 mm section. A larger FRP-TES is fabricated to demonstrate practicality for personal mobility. Incorporating FRP-TES units into road infrastructure can enhance structural stability while providing reliable real-time data for traffic monitoring, accident response, and prediction.

Integration of N- and P- elements in sodium alginate aerogels for efficient flame retardant and thermal insulating properties

In the field of building energy conservation, the development of biodegradable biomass aerogels with excellent mechanical performance, flame retardancy and thermal insulation properties is of particular importance. Here, a directional freeze-drying method was used for fabricating composite sodium alginate (SA) aerogels containing functionalized ammonium polyphosphate (APP) flame retardant. In particular, APP was coated with melamine (MEL) and phytic acid (PA) by a supramolecular assembly process. Through optimizing the flame retardant addition, the SA-20 AMP sample exhibited excellent flame retardant and thermal insulation properties, with the limiting oxygen index of 38.2 % and the UL-94 rating of V-0. Such aerogels with anisotropic morphology demonstrated a low thermal conductivity of 0.0288 (W/m·K) in the radial direction (perpendicular to the lamellar structure). In addition, as-obtained aerogels displayed remarkable water stability and mechanical properties, indicating significant potential for practical applications.

Development of Reagents - Blowing Agents Based on Local Raw Materials and their Research

The development and search for effective reagents and optimal technological conditions is one of the main factors for improving the coal flotation process. Solving these problems increases the technological and economic efficiency of flotation enrichment. The article discusses methods for producing foaming regents based on waste from the distillation process of cottonseed oil - gossypol resin and methods of flotation of various classes of fine coal. The advantages of this foaming agent include the availability of raw materials, which are a product of domestic industry, produced at the enterprises of the Kattakurgan MJK and amino alcohols (mono- , di- and triethanolamine) , sufficient resources and relative low cost. Conducted research to assess the effectiveness, surface activity and foaming ability of the resulting reagents - in foaming agents, according to the proposed technology of the studied technical products, the resulting product belongs to the surface-active reagents and has high flotation activity. The physico-chemical and foam-forming properties, foam stability, destruction kinetics and other properties of flotation reagents - foaming agents SK-1 and SK-2 - have been studied. The results of studies of the influence of foaming reagents in the process of flotation and extraction of precious and non-ferrous metals are presented. The optimal option for the effective composition of composite chemical flotation reagents - foaming agents and their parameters was selected. The results of scientific research conducted at JSC NMMC on the use of analogues of the foaming agents SK-1 and SK-2 are given in comparison with the reagents (Oxal) currently used at the plant. The elemental composition of man-made waste samples using reagents SK-1 and SK-2 was determined.

Density Functional Theory Study of AlN Nanosheets with Biphenylene Structure: Stability, Electronic, Thermoelectric, Mechanical, and Optical Properties

Density Functional Theory Study of AlN Nanosheets with Biphenylene Structure: Stability, Electronic, Thermoelectric, Mechanical, and Optical Properties

Glycine-Modified Co-MOF Pervaporation Membrane to Enhance Water Transporting.

Cobalt-based metal-organic frameworks (Co-MOFs) with a two-dimensional layered morphology have received increasing attention for pervaporation due to their stability and hydrophilic properties. Using amino glycine (Gly) as a cross-linking agent, the Co-MOF ultrathin two-dimensional membrane doped with organic filler sodium alginate (SA) with the "brick-mixed-sand" structure was proposed. Polyacrylonitrile (PAN) was selected as the support layer of the hybrid membrane. The introduction of Gly efficiently solved the nanomaterial stacking problem and controllably adjusted the interlayer spacing between the nanosheets, which demonstrated good performance for ethanol dehydration. The results of this experimental research showed that the total flux of alcohol/water (9:1) separation by Gly-Co-MOF-SA/PAN hybrid membranes reached 1902 g m-2 h-1, which was 67% higher than that of the pure SA membranes. The "brick-mixed-sand" lamellar dense morphology of Gly-Co-MOF not only enhances membrane hydrophilicity but also provides effective channels for the rapid transport of water, which is expected to be used for the dehydration of organic solvents.

Design and Construction of Furan and Thiophene‐Based Salicyladazine Bisbenzoxazine Resins with High Thermal Stability and Tunable Surface Properties

Design and Construction of Furan and Thiophene‐Based Salicyladazine Bisbenzoxazine Resins with High Thermal Stability and Tunable Surface Properties

Furan-oxadiazole hybrids as promising antioxidants: Synthesis, characterization, ADME and molecular docking studies on peroxiredoxin-2

The study involves the synthesis and characterization of a novel series of furan-based compounds 1–9 incorporating strategic modifications with isatin, pyrazole, and oxadiazole motifs. The synthesized compounds were characterized and assigned with different spectroscopic techniques such as FT-IR, 1H NMR, 13C NMR and mass spectra. Antioxidant screening assays using the DPPH radical scavenging method revealed that the oxadiazole derivative 9 exhibited exceptional antioxidant activity, with an EC50 value of 0.0038 mM, attributed to the oxadiazole ring's favourable electron delocalization and radical stabilization properties. Molecular docking simulations with the Peroxiredoxin-2 (Prdx-2) crystal structure (PDB: 5IJT) predicted favourable binding interactions for the synthesized compounds, with docking scores ranging from -6.1629 to -7.9878 kcal/mol. The sugar moieties facilitated hydrogen bonding interactions with key active site residues, while the furan and phenyl rings contributed to π-hydrogen interactions. Furthermore, in silico ADME prediction studies assessed the drug-likeness and pharmacokinetic properties of the compounds, identifying promising lead candidates for further optimization and development as potential antioxidant therapeutics targeting Prdx-2.