Solid Rigid Polyurethane Research Articles

Pull-Out Strength of Orthodontic Miniscrews in the Temporal Bone.

Minimally invasive cochlear implant surgery by using a microstereotactic frame demands solid connection to the bone. We aimed to determine the stability of commercially available orthodontic miniscrews to evaluate their feasibility for frame's fixation. In addition, which substitute material most closely resembles the mechanical properties of the human temporal bone was evaluated. Pull-out tests were carried out with five different types of orthodontic miniscrews in human temporal bone specimens. Furthermore, short fiber filled epoxy (SFFE), solid rigid polyurethane (SRPU50), bovine femur, and porcine iliac bone were evaluated as substitute materials. In total, 57 tests in human specimens and 180 tests in the substitute materials were performed. In human temporal bone, average pull-out forces ranged from 220 N to 285 N between screws. Joint stiffness in human temporal bone ranged between 14 N/mm and 358 N/mm. Statistically significant differences between the tested screws were measured in terms of stiffness and elastic energy. One screw type failed insertion due to tip breakage. No significant differences occurred between screws in maximum pull-out force. The average pull-out values of SFFE were 14.1 N higher compared to human specimen. Orthodontic miniscrews provided rigid fixation when partially inserted in human temporal bone, as evidenced by pull-out forces and joint stiffness. Average values exceeded requirements despite variations between screws. Differences in stiffness and elastic energy indicate screw-specific interface mechanics. With proper insertion, orthodontic miniscrews appear suitable for microstereotactic frame anchoring during minimally invasive cochlear implant surgery. However, testing under more complex loading is needed to better predict clinical performance. For further pull-out tests, the most suitable substitute material is SFFE.

Use of a Novel Artificial Intelligence Tool for Evaluating Primary Stability and Immediate Loading Suitability of Dental Implants: An In Vitro Pilot Study.

To evaluate the correspondence between output from a new artificial intelligence tool (AIT) and clinician evaluation regarding the immediate loading suitability of dental implants based on insertion torque curves recorded during implant placement in an in vitro test. The secondary aim was to analyze peak insertion torque (PIT) and variable torque work (VTW) values of the implants. The study was performed with four different densities of artificial bone blocks of solid rigid polyurethane without a cortical layer. Five types of implants with different macrogeometries were used. A total of 140 implants (7 implants of each type in the four polyurethane blocks) were inserted. Immediately after implant placement, the insertion torque curves were classified by the operator as suitable (S) or nonsuitable (NS) for immediate loading. The same curves were then analyzed by the new AIT, which classified them as belonging to the 'YES' or 'NO' class. For each implant, PIT and VTW values were also recorded. The correspondence between clinician and AIT evaluation was 99.3%, with only one false negative reported by the algorithm analysis. The AIT was found to have a sensitivity of 98.95%, specificity of 100%, positive predictive value of 100%, and negative predictive value of 97.8%. Mean PIT of the whole sample was 34.19 ± 19.43 Ncm, while mean VTW was 2,266.89 ± 1,993.73 Ncm. Statistically significant differences were found between implant systems in the whole sample and according to density of the polyurethane block. The AIT showed a high level of accuracy in the prediction of immediate loading suitability of dental implants based on the provided insertion torque curves. All the implants used in the in vitro test achieved good levels of primary stability, except when inserted in the least-dense polyurethane block. Clinical studies conducted with larger samples and more clinicians are necessary to confirm these results.

Bone density and proximal support effects on dental implant stability – Finite element analysis and in vitro experiments

ObjectivesThe application of dental implants presents the occurrence of implant failures associated with bone proximal support. This study aims to assess implant behavior, in particular implant stability and strain distribution in the bone at different bone densities, and the effect of proximal bone support. Material and methodsThree bone densities (D20, D15, and D10) were considered in the experimental in vitro study, represented by solid rigid polyurethane foam and two conditions of bone support in the proximal region. A finite element model was developed and validated experimentally and a Branemark model at a 3:1 scale was implanted in the experiments; the model was loaded and extracted. ResultsThe results of the experimental models validate the finite element models with a correlation R2 equal to 0.899 and NMSE of 7%. The implant extraction tests for the effect of bone properties in the maximum load were 2832 N for D20 and 792 N for D10. The effect of proximal bone support changes the implant stability was observed experimentally; at 1 mm less bone support decreases by 20% of stability and at 2 mm by 58% for D15 density. ConclusionsBone properties and bone quantity are important for the initial stability of the implant. A bone volume fraction of less than 24 g/cm3 exhibits poor behavior and is not indicated for implantation. Proximal bone support reduces the primary stability of the implant and the effect is critical in lower bone density.

Reverse total shoulder arthroplasty baseplate stability with locking vs. non-locking peripheral screws

BackgroundThere are many options for glenosphere baseplate fixation commercially available, yet there is little biomechanical evidence supporting one type of fixation over another. In this study, we compared the biomechanical fixation of a reverse total shoulder glenoid baseplate secured with locking or non-locking peripheral screws. MethodsBoth a non-augmented mini baseplate with full backing support and an augmented baseplate were testing after implantation in solid rigid polyurethane foam. Each baseplate was implanted with a 30 mm central compression screw and four peripheral screws, either locking or non-locking (15 mm anterior/posterior and 30 mm superior/inferior). A 1 Hz cyclic force of 0-750 N was applied at a 60o angle for 5000 cycles. Throughout the test, the displacement of the baseplate was measured using a 3D Digital Image Correlation System. FindingsThe amount of migration measured in the both the non-augmented and augment cases shows no significant differences between locking and non-locking cases at the final cycle count (non-augment: 5.66 +/− 2.29 μm vs. 3.71 +/− 1.23 μm; p = 0.095, augment: 15.43 +/− 8.49 μm vs. 12.46 +/− 3.24 μm; p = 0.314). Additionally, the amount of micromotion measured for both sample types shows the same lack of significant difference (non-augment: 10.79 +/− 5.22 μm vs. 10.16 +/− 7.61 μm; p = 0.388, augment: 55.03 +/− 10.13 μm vs. 54.84 +/− 10.65 μm; p = 0.968). InterpretationThe presence of locking versus non-locking peripheral screws does not make a significant difference on the overall stability of a glenoid baseplate, in both a no defect case with a non-augmented baseplate and a bone defect case with an augmented baseplate.

Fixture Length and Primary Stability: An In Vitro Study on Polyurethane Foam

(1) Background: Recently, novel dental implants that are characterized by different levels of surface roughness in the distinct parts of the fixture’s body have been introduced in the market. These surface characteristics could affect the primary stability of the implants. The aim of this in vitro study was to compare the primary stability of short and long implants, characterized by multiscale surface roughness, inserted on polyurethane blocks. The secondary aim was to understand if the implant length could be a crucial factor in the decision-making in immediate or rather than delayed loading protocol in the different bone densities. (2) Methods: A total of 20 cylindrical dental implants with a diameter of 5.0 mm were tested for the lengths 6.0 mm (short implants) versus 13.0 mm (long implants) on two different solid rigid polyurethane blocks (20 and 30 PCF). The primary stability was evaluated by measuring the insertion torque value (ITV), the removal torque (RTV), and the resonance frequency analysis RFA. (3) Results: The values of ITV, RTV, and RFA showed the same trend in all measurements. Long implants showed a significantly higher primary stability on 30 PCF blocks that present mechanical properties similar to high-density bone. On the contrary, no relevant differences were found on 20 PCF blocks, which mimic trabecular bone density. (4) Conclusions: The impact of fixture length on the primary stability of implants with multiscale surface roughness is significant in 30 PCF polyurethane corresponding to higher bone density, but not in lower ones.

Deflection of mini implants from its intended path of placement on varying bone densities.

Knowledge of bone density in maxilla and mandible will allow the clinician to plan the anchorage strategies and placement of implants with necessary precautions. The study aims to evaluate the deflection changes of titanium alloy self-drilling mini implants from the intended path that occurs during placement in varying bone densities. 63 titanium alloy self-drilling mini implants of the lengths 6mm, 8mm, and 10mm with diameter of 1.3mm were placed in three homogenous solid rigid polyurethane foam (saw bone) with bone densities of 20pcf, 30pcf, and 40pcf simulating anatomic sites in maxilla and mandible. 7mini implants of each length in all bone densities were tested for study. The implants were inserted perpendicularly into artificial bone block held in a custom made stand. The bone blocks were then radiographically exposed and the deviation of the long axis of the implantfrom a true vertical line was measured. There was a decrease in deflection of the mini implant with increase in density. On the other hand, increase in length resulted in increase in the amount of deflection. Longer mini implants can be used in less dense bone as in maxilla, whereas shorter mini implants can be used in high dense bone as in mandible to increase the stability and success rate of implants. Bone density and implant length play a role in deflection of mini implant from its intended path of insertion. Key words:Orthodontic Mini implants, deflection, bone density, anchorage.

Influence of Cortical Layer and Surgical Techniques on the Primary Implant Stability in Low-density Bone:An In Vitro Study

This study aimed at evaluating the influence of cortical layer and surgical techniques on the primary stability of implants in low-density bone. Two solid rigid polyurethane blocks with a density equivalent to 0.32 g/cm3 simulating cancellous bone were used. A short fiber-filled epoxy resin sheet of 2 mm was layered to one block to simulate cortico cancellous bone. A total of 40 implants were used in this study (n = 40). Twenty implants each (n = 20) were inserted in cancellous (Group 1) and cortico-cancellous bone (Group 2), of which 10 implants each (n = 10) were placed using undersized preparation technique with surgical drills-A and osteotomes-B, in both the groups. Insertion torque (IT) and implant stability quotient (ISQ) for each implant placed were assessed to determine the primary stability of each implant using a digital torque meter and resonance frequency analyzer, respectively. The values were statistically analyzed using an independent t-test (p < 0.05). Pearson's correlation analysis was performed to correlate between IT and ISQ. Technique B resulted in significantly higher IT and ISQ values in Group 1 (27.69 ± 1.2 N cm; 52.5 ± 1.05 ISQ) and Group 2 (38.8 ± 0.87 N cm; 70.1 ± 1.04 ISQ) compared to those with technique A (22.40 ± 1.62 N cm; 41.75 ± 1.20 ISQ and 33.24 ± 0.67 N cm; 63.72 ± 1.33 ISQ), respectively. Group 2 exhibited significantly higher IT and ISQ values as compared to Group 1 irrespective of the surgical technique employed (p < 0.05). The presence of the cortical layer significantly influenced the primary stability and preparing low-density bone with an undersized preparation technique using osteotomes that significantly increased the IT and ISQ. Undersizing the preparation site considerably will help achieve a significant increase in primary stability in the poor quality bone as in the posterior maxilla, thereby contributing to the success of the implant.

The Assessment of the Maximum Heat Production and Cooling Effectiveness of Three Different Drill Types (Conical vs. Cylindrical vs. Horizontal) during Implant Bed Preparation—An In Vitro Study

The aim of this experimental study was to verify thermal diffusion differences, by measuring the maximum temperature achieved with different drill shapes. Synthetic bone blocks of type I density made from solid rigid polyurethane (PUR) foam were used to perform the drilling procedures. The experiment was conducted at three different rotation speeds: 800, 3000 and 5000 rpm. Conical drills (with and without an internal cooling hole) were compared with horizontal drills and disc drills. The temperature during drilling for implant bed preparation was estimated with the use of thermocouples and an infrared (IR) camera. The temperature during drilling with disc cutters for lateral basal implants did not exceed 33 ∘C and the temperature decreased in proportion to higher drill speed. The results indicate that the tested design is safe and will not cause bone overheating.

The Influence of the Implant Macrogeometry on Insertion Torque, Removal Torque, and Periotest Implant Primary Stability: A Mechanical Simulation on High-Density Artificial Bone

Background: The primary stability is a determinant clinical condition for the success of different dental implants macro-design in different bone density using a validated and repeatable in vitro technique employing solid rigid polyurethane blocks. Materials and Methods: Five implants 3.8 × 13 mm2 for each macro-design (i.e., IK—tapered; IC—cylindric; and IA—active blade shape) were positioned into 20- and 30- pounds per cubic foot (PCF) polyurethane blocks. Bucco-lingual (BL) and mesial-distal (MD) implant stability quotient score (ISQ) was assessed by resonance frequency analysis while, insertion/removal torques were evaluated by dynamometric ratchet. Results: IC implants shown better primary stability in terms of ISQ compared to IA and IK in lower density block (20 PCF), while IK was superior to IA in higher density (30 PCF). IC shown higher removal torque in 30-PCF compared to IA and IC. Conclusions: The study effectiveness on polyurethane artificial bone with isotropic symmetry structure showed that the implants macro-design might represent a key factor on primary stability, in particular on low-density alveolar bone. Clinicians should consider patients features and implant geometry during low-density jaws rehabilitation. Further investigations are needed to generalize these findings.

Intra-osseous heat generation during implant bed preparation with static navigation: Multi-factor in vitro study.

To compare the intra-osseous temperature reached during bone drilling for dental implant placement using open versus closed static surgical guides and evaluate the influence of bone density, osteotomy drilling depth, and irrigation fluid temperature. 960 osteotomies were performed with 2mm pilot drills in 16 solid rigid polyurethane foam blocks. Two main variables were considered: the guide type (open or closed guide) and bone density (hard (D1) or soft (D4). The blocks were divided into four groups according to the type of surgical template and bone density as follows: group one: closed guide and hard bone; group two: open guide and hard bone; group three: closed guide and soft bone; and group four: open guide and soft bone. A combination of different experimental conditions was used, including different bone osteotomy depths (6 or 13mm) and irrigation fluid temperatures (5°C or 21°C). The highest mean temperature was found in group one (28.29±4.02°C). In the soft bone groups (three and four), the mean maximum temperature decreased compared to groups one and two (dense bone) and was always higher with closed guides (23.38±1.92°C) compared to open guides (21.97±1.22°C) (p<.001). The osteotomy depth and irrigation fluid temperature also significantly influenced the bone temperature (p<.001), especially in hard bone. The greatest heat generation was observed in high-density bone. The final intra-bone temperature was about 1°C higher with a closed static surgical guide than with an open guide. The heat generation in osteotomy sites was substantially reduced by cooling the irrigation fluid to 5°C.

Comparative Evaluation of Primary Stability between Different Diameters Multi-Scale Roughness Dental Implant by Solid Rigid Polyurethane Simulation

Background: Implant primary stability is determined by screw characteristics and surgical procedure. The aim of the present study was to evaluate, on a polyurethane model, the insertion torque (IT), removal torque (RT), and resonance frequency analysis (RFA) of multi-scale roughness dental implants of different diameters. Methods: Two implant sizes were tested on two polyurethane blocks (20 pounds per cubic foot (PCF) and 30 PCF): 3.0 diameter and 13 mm length and 5.0 diameter and 13 mm length. The IT, RT, and RFA were assessed. Results: A significant difference of IT and RT was present in favor of wider implants at both polyurethane densities. No statistical difference was present between the 5.0 diameter and 3.0 diameter implants at both polyurethane densities. A statistically increased RFA was reported for 5.0 implant 30 PCF polyurethane blocks. Conclusions: Multi-scale roughness dental implants of both diameters showed high insertion torque and primary stability on polyurethane blocks, which is valuable for implant loading protocols.

Influence of the dental implant macrogeometry and threads design on primary stability: an in vitro simulation on artificial bone blocks

The implant macrogeometry and thread profile represent one of the most important factors for a successful achievement of primary stability during the positioning procedure. The aim of the present investigation was to evaluate the insertion torque (IT), removal torque (RT) and Implant stability Quotient (ISQ) of two different implant macrogeometry and thread profile on solid rigid polyurethane model. Two different implants macrogeometries were tested: K2 (Group I) with 11° angle, 1.17 mm pitch and self-cutting V thread profile and K3 (Group II) implants with 30° angle, 0.71 mm pitch and spyral thread profile. A total of 120 specimens (n = 60 for each group) were positioned into different conditions of solid rigid polyurethane blocks. The insertion torque (IT), removal torque (RT) and ISQ were measured for each specimen. All specimens achieved the positioning into solid rigid polyurethane blocks for both of groups with no loss of stability. A significantly higher IT, RT and ISQ were detected in Group II (p < 0.05). In both groups the mean values for IT, RT and ISQ appeared promising from a clinical point of view. In spite of different macrogeometry and thread profile, both implant types achieved high primary stability on solid rigid polyurethane block to support the functional loading for a clinical application.

Mechanical Performance of Metallic Bone Screws Evaluated Using Bone Models.

To evaluate mechanical performance properties of various types of cortical bone screw, cancellous bone screw, and locking bolt, we conducted torsional breaking and durability tests, screw driving torque tests into bone models, and screw pullout tests (crosshead speed: 10 mm/min) after driving torque tests. The 2° proof and rupture torques of a screw, which were estimated from torque versus rotational angle curves, increased with increasing core diameter of the screw. The durability limit of metallic screws obtained by four-point bending durability tests increased with increasing core diameter. The compressive, tensile, and shear strengths of the bone models used for the mechanical testing of orthopedic devices increased with increasing density of the bone model. The strength and modulus obtained for solid rigid polyurethane foam (SRPF) and cellular rigid polyurethane foam (CRPF) lay on the same straight line. Among the three strengths, the rate of increase in compressive strength with the increase in density was the highest. The maximum torque obtained by screw driving torque tests for up to 8.3 rotations (3000°) into the bone models tended to increase with increasing core diameter. In particular, the maximum torque increased linearly with increasing effective surface area of the screw, as newly defined in this work. The maximum pullout load increased linearly with increasing number of rotations and mechanical strength of the bone model. Screws with low driving torque and high pullout load were considered to have excellent fixation and are a target for development.

Primary Stability of Short Implants Inserted Using Piezoelectric or Drilling Systems: An In Vitro Comparison.

The primary objective of the present in vitro study was to evaluate the influence of implant site preparation technique (drills vs ultrasonic instrumentation) on the primary stability of short dental implants with two different designs inserted in simulated low-quality cancellous bone. Eighty implant sites were prepared in custom-made solid rigid polyurethane blocks with two different low cancellous bone densities (5 or 15 pounds per cubic foot [PCF]), equally distributed between piezoelectric (Surgysonic Moto, Esacrom, Italy) and conventional drilling techniques. Two short implant systems (Prama and Syra, Sweden & Martina) were tested by inserting 40 fixtures of each system (both 6.0 mm length and 5.0 mm diameter), divided in the four subgroups (drills/5 PCF density; drills/15 PCF density; piezo/5 PCF density; piezo/15 PCF density). Insertion torque (Ncm), implant stability quotient values, removal torque (Ncm), and surgical time were recorded. Data were analyzed by 3-way ANOVA and Scheffé's test (α = 0.05). With slight variations among the considered dependent variables, overall high primary implant stability was observed across all subgroups. Piezoelectric instrumentation allowed for comparable or slightly superior primary stability in comparison with the drilling procedures in both implant systems. The Prama implants group showed the highest mean reverse torque and Syra implants the highest implant stability quotient values. Piezoelectric implant site preparation took prolonged operative time compared to conventional preparation with drills; among the drilling procedures, Syra system required fewer surgical steps and shorter operative time.

Primary stability of short implants inserted using piezoelectric or drilling systems: an in vitro comparison.

The primary objective of the present in vitro study was to evaluate the influence of implant site preparation technique (drills vs. ultrasonic instrumentation) on the primary stability of short dental implants with two different designs inserted in simulated low quality cancellous bone. Eighty implant sites were prepared in custom-made solid rigid polyurethane blocks with two different low cancellous bone densities (5 or 15 pounds per cubic foot, PCF), equally distributed between piezoelectric (Surgysonic Moto, Esacrom, Italy) and conventional drilling techniques. Two short implant systems (Prama and Syra, Sweden & Martina) were tested by inserting 40 fixtures of each system (both 6.0 mm length and 5.0 mm diameter), divided in the four subgroups (drills/5 PCF density; drills/15 PCF density; piezo/5 PCF density; piezo/15 PCF density). Insertion torque (Ncm), implant stability quotient values, removal torque (Ncm) and surgical time were recorded. Data were analyzed by three-way ANOVA and Scheffé's test (α=0.05). With slight variations among the considered dependent variables, overall high primary implant stability was observed across all subgroups. Piezoelectric instrumentation allowed for comparable or slightly superior primary stability in comparison with the drilling procedures in both implant systems. Prama implants group showed the highest mean reverse torque, Syra implants the highest implant stability quotient values. Piezoelectric implant site preparation took prolonged operative time compared to conventional preparation with drills; among the drilling procedures, Syra system requires fewer surgical steps and shorter operative time.

Fixation Strength of Polyetheretherketone Sheath-and-Bullet Device for Soft Tissue Repair in the Foot and Ankle

Tendon transfers are often performed in the foot and ankle. Recently, interference screws have been a popular choice owing to their ease of use and fixation strength. Considering the benefits, one disadvantage of such devices is laceration of the soft tissues by the implant threads during placement that potentially weaken the structural integrity of the grafts. A shape memory polyetheretherketone bullet-in-sheath tenodesis device uses circumferential compression, eliminating potential damage from thread rotation and maintaining the soft tissue orientation of the graft. The aim of this study was to determine the pullout strength and failure mode for this device in both a synthetic bone analogue and porcine bone models. Thirteen mature bovine extensor tendons were secured into ten 4.0 × 4.0 × 4.0-cm cubes of 15-pound per cubic foot solid rigid polyurethane foam bone analogue models or 3 porcine femoral condyles using the 5 × 20-mm polyetheretherketone soft tissue anchor. The bullet-in-sheath device demonstrated a mean pullout of 280.84 N in the bone analog models and 419.47 N in the porcine bone models. (p = .001). The bullet-in-sheath design preserved the integrity of the tendon graft, and none of the implants dislodged from their original position.

DYNAMIC NUMERICAL SIMULATION OF DIFFERENT DRILL BIT DIAMETER ON THE POLYURETHANE FOAMS DRILLING

Drilling is one of the most common processes involved in different cutting operations and may affect the mechanical properties of the workpiece by creating residual stresses around the opened hole and highly stressed on the newly formed surface. Nevertheless, when it comes to the living tissues, drilling assumes more attention to guarantee a non-invasive procedure. Drilling of bone is common in orthopaedic surgical process, to produce a hole to screw insertion to fix the fractured members for immobilization, or even in dental implant interventions. This work describes a conventional drilling process performed on solid rigid polyurethane foams blocks with similar mechanical properties to the human bone. A dynamic and numerical study was conducted to evaluate the use of different drill diameters (4, 5 and 6mm) on the stresses generated during the process. Different simulations using an explicit dynamic program were performed to assess the level of stresses and the damage effect on the polyurethane foam structure. This program is based on the finite element method and incorporates the dynamic characteristics involved in the drilling process. The main objective of this study is to verify the combination between some drill parameters, that reduce the mechanical damage produced by high stress level during bone drilling. The results permit to assess the influence of the drill bit diameter using a constant feed-rate (75mm/min) and drill speed (600rpm). For these conditions, results show that the smaller drill bit diameter leads to a decrease in the stress level in the foam material during the process. Article DOI: https://dx.doi.org/10.20319/mijst.2017.33.112 This work is licensed under the Creative Commons Attribution-Non-commercial 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by-nc/4.0/ or send a letter to Creative Commons, PO Box 1866, Mountain View, CA 94042, USA.

THERMAL ANALYSIS IN DRILLING OF EX VIVO BOVINE BONES

Bone drilling is a common procedure in Medicine, mainly in traumatology and orthopedic procedure for fractures fixation and in reconstructive surgery. The success of this surgical procedure is dependent on many factors, namely, on heat generation control during the bone drilling. The main concern in bone drilling is the mechanical and thermal damage of the bone induced by inappropriate parameters such as drill speed and feed-rate during the drilling. This study focuses on the temperature generated during drilling of cortical bone tissue (bovine origin) and solid rigid polyurethane foams with similar mechanical properties to the human bone tissue. Different parameters such as drill speed, feed-rate and hole depth were tested. All results showed that improvement of the drilling parameters and the drill temperatures can be estimated. It was concluded that when the drill speed and feed-rate were higher, the bone temperature increase was lower. The obtained results of temperature in the drilling process of polyurethane foam blocks or bovine bone were compared with a good agreement in between both.

Reverse total shoulder glenoid baseplate stability with superior glenoid bone loss

Superior wear of the glenoid bone is common in patients with rotator cuff arthropathy. This can become a treatment challenge for patients who require shoulder arthroplasty. In reverse shoulder arthroplasty (RSA), glenoid bone loss may affect the stability of baseplate fixation. The primary purpose of this biomechanical laboratory study was to assess the initial fixation stability of RSA glenosphere baseplates in the presence of variable amounts of superior glenoid bone loss. High-density solid rigid polyurethane foam (30 pounds/cubic foot) was machined to model the glenoid with variable superior defects that provided different levels of support (100%, 90%, 75%, and 50%) for the glenosphere baseplate. The samples were cyclically loaded (0-750 N at 1 Hz for 5000 cycles) at a 60° glenohumeral angle. The micromotion and migration of the baseplate were calculated from displacement data captured during the loading tests with an array of 3 linear variable differential transformers mounted around the baseplate. Micromotion was significantly greater in samples with 50% defects compared with those with smaller defects. Migration was significantly greater after testing for all defect sizes. Initial fixation of RSA glenosphere baseplates was significantly reduced in models with 50% bone loss on the superior edge compared with models with less bone loss in this high-density bone foam model.

Effect of interfragmentary gap on compression force in a headless compression screw used for scaphoid fixation.

We investigated the effect of an interfragmentary gap on the final compression force using the Acutrak 2 Mini headless compression screw (length 26 mm) (Acumed, Hillsboro, OR, USA). Two blocks of solid rigid polyurethane foam in a custom jig were separated by spacers of varying thickness (1.0, 1.5, 2.0 and 2.5 mm) to simulate an interfragmentary gap. The spacers were removed before full insertion of the screw and the compression force was measured when the screw was buried 2 mm below the surface of the upper block. Gaps of 1.5 mm and 2.0 mm resulted in significantly decreased compression forces, whereas there was no significant decrease in compression force with a gap of 1 mm. An interfragmentary gap of 2.5 mm did not result in any contact between blocks. We conclude that an increased interfragmentary gap leads to decreased compression force with this screw, which may have implications on fracture healing.