Reduction In Size Research Articles

Heat Propagation Across Turbocharger Unit with Variable Turbine Inlet Temperature

Currently, issues about emission gains serious attention among the lawmakers and governments. Multiple regulation and enforcements have been applied to reduce the level of emission that released to the environment. Vehicle emissions have been identified as one of the major polluters thus forcing the carmakers to explore new technology to reduce the vehicle emissions. One of the technologies that have been preferred by the carmakers is the applications of forced induction system to the internal combustion engine. By using the forced induction system where currently turbocharger system is more often used compared to supercharger, two benefits can be achieved which are improvements of engine efficiency and engine size reduction. However, the ability of turbocharger unit to deliver compressed air can be affected by the amount of heat that travels along the turbocharger unit itself. In this paper, the effect of heat that originated from the exhaust gas that enters the turbine inlet towards the turbocharger performance was measured and analysed. An automotive turbocharger unit manufactured by Garrett Turbocharger model GT2056 was used in the study. The rotational speed is set between 20 000 rpm to 70 000 rpm and the temperature at turbine inlet is set between 40℃ to 100℃. The parameters that measured are the temperature difference at internal turbine, internal bearing temperature difference, internal compressor temperature difference, turbine casing temperature difference, bearing housing temperature difference and compressor housing temperature difference. From the results obtained, it can be observed that the heat travels from turbine towards the compressor side through the conduction between the contacting parts between the turbine casing, bearing housing and lastly at compressor casing. The heat that arrives at the compressor side through the casing will give small effect to the air mass flow that delivered by the compressor.

Effectiveness and safety of the modified multiple mode procedures versus traditional multiple mode procedures on treating facial atrophic acne scars: a propensity score matching retrospective cohort study.

Multiple mode procedures (MMP) of fractional CO2 laser provide higher efficacy and shorter downtime in treating acne scars, compared to traditional fractional CO2 laser therapy. This study aims to evaluate the effectiveness and safety of modified MMP integrated with fractional microneedle radiofrequency (FMR), ultra-pulse CO2 laser and fractional CO2 laser in treating acne scars. A retrospective analysis of 162 acne scar patients treated with MMP or modified MMP was conducted. Acne scars were evaluated using the Echelle d'Evaluation Clinique des Cicatrices d'Acné (ECCA) grading scale, modified Manchester Scar Scale (mMSS), and Global Assessment Scale (GAS). Baseline variables were balanced with propensity score matching (PSM) to improve the comparability of treatment effectiveness and safety between groups. Among 162 patients with facial acne scars, 68 were treated with modified MMP and 94 with traditional MMP. After PSM, both groups had 55 patients with comparable baseline characteristics (P > 0.05). The ECCA score decreased more significantly in the modified MMP group (60%±11%) than in the MMP group (45%±16.6%, P < 0.001). The modified MMP group also had higher mMSS color score (2.6 ± 0.7 vs. 2.1 ± 0.9, P = 0.005), greater reduction in pore size and skin laxity (P < 0.001), shorter postoperative erythema duration (22.2 ± 4.0 vs. 31.3 ± 3.7 days, P < 0.001), but higher pain scores (Visual Analogue Scale, VAS: 6.7 ± 1.6 vs. 3.8 ± 0.8, P < 0.001). Modified MMP is more effective than traditional MMP in treating acne scars, especially for patients with large pores and skin laxity.

Efficacy and safety of levosimendan in patients with ST-segment elevation myocardial infarction undergoing primary percutaneous coronary intervention: The LEVOCEST trial.

Primary angioplasty is the standard procedure for patients with ST-segment elevation myocardial infarction (STEMI). However, myocardial reperfusion results in additional cell damage. Levosimendan, due to its pleiotropic effects, may be a therapeutic alternative to prevent this damage. The objective of this study was to evaluate whether this drug can reduce infarct size in patients with STEMI. Patients were randomized to receive a 24-h infusion of either levosimendan (0.1 μg/kg/min) or placebo after the primary angioplasty. The main objective was to assess the size of the infarct by cardiac resonance at 30 days and 6 months after the event. Other variables such as left ventricular ejection fraction (LVEF) and adverse ventricular remodeling (AVR) were assessed by speckle-tracking echocardiography and magnetic resonance. Major adverse cardiovascular events (MACE) were also collected. 157 patients were analysed (levosimendan, n = 79; placebo, n = 78). We found that after 6 months, patients treated with levosimendan had a greater reduction in infarct size (13.19% ± 9.5% vs.11.79% ± 9%, p = 0.001), compared with those in the placebo group (13.35% ± 7.1% vs. 13.43% ± 7.8%, p = 0.38). There were no significant differences in MACE between both groups. Levosimendan is a safe and effective therapeutic option for reducing infarct size in patients with STEMI.

Differences in Anthropogenic Impacts of Typical Mid- to High-Latitude Wetlands in the Heilongjiang Basin

Wetlands represent one of the three principal ecosystems and serve a vital function in the protection of water resources and the regulation of climate. However, wetlands are currently experiencing significant challenges, particularly in the agriculturally productive wetlands of the Heilongjiang River Basin, which have been considerably impacted by human activities. This study focuses on three representative wetlands situated within the Heilongjiang River Basin. This study analyses changes in wetland area and landscape patterns from 2002 to 2022, as well as the impact of agriculture and impervious surface expansion on the wetlands. The findings indicate that agricultural expansion is the primary driver of wetland area loss. The wetland area affected by agriculture demonstrates the most significant change, with the largest observed shift reaching 47.2%. The expansion of impervious surfaces was found to have a significant impact on wetland fragmentation, resulting in a notable decrease in wetland connectivity. This was evidenced by a reduction in the average patch size, which decreased by 14.68 ha over the decade from 2007 to 2017, a period during which impervious surfaces expanded. This paper identifies the distinctions in the influence of diverse human activities on wetland landscape patterns in the Heilongjiang Basin and employs natural samples for control, thereby attenuating the impact of the natural environment. This study offers a novel perspective on the processes of wetland change and the maintenance of wetland health, which is crucial for the realisation of clean water and sanitation (Sustainable Development Goal 6.6).

The Impact of RNA Interference on Atherosclerotic Plaque Progression: A Meta-Analysis of Preclinical Studies

Background: Atherosclerosis, a chronic inflammatory disease characterized by the buildup of plaque within arteries, remains a leading cause of cardiovascular morbidity and mortality. RNA interference (RNAi) has emerged as a promising therapeutic strategy for atherosclerosis by targeting genes involved in plaque formation and progression. This meta-analysis aimed to evaluate the efficacy of RNAi in preclinical models of atherosclerosis. Methods: A systematic search of PubMed, Embase, and Web of Science databases was conducted from January 2013 to December 2023 to identify preclinical studies investigating the impact of RNAi on atherosclerotic plaque progression. Studies utilizing various RNAi modalities (siRNA, miRNA mimics/inhibitors, shRNA) targeting different genes involved in atherosclerosis were included. The primary outcome was plaque size reduction. Secondary outcomes included changes in plaque composition, lipid profiles, and inflammatory markers. A random-effects model was used to pool data and calculate standardized mean differences (SMD) with 95% confidence intervals (CI). Heterogeneity was assessed using the I² statistic. Results: Seven preclinical studies met the inclusion criteria, encompassing a total of 210 animals. RNAi interventions significantly reduced atherosclerotic plaque size compared to controls (SMD -1.51; 95% CI -2.36 to -0.66; p&lt;0.00001; I²=12%). Analysis of secondary outcomes revealed favorable effects of RNAi on plaque composition, with a significant decrease in lipid content and an increase in collagen content. Furthermore, RNAi significantly improved lipid profiles by reducing total cholesterol and LDL-cholesterol levels. A significant reduction in inflammatory markers, such as TNF-α and IL-6, was also observed. Conclusion: This meta-analysis provides compelling evidence supporting the therapeutic potential of RNAi in attenuating atherosclerotic plaque progression in preclinical models. RNAi effectively reduced plaque size, improved plaque stability, and modulated lipid metabolism and inflammation.

Bimodal grain structure, phase transformation, and mechanical properties of a Mg-Gd-Y-Zn-Zr alloy during hot extrusion

In this study, we investigated the evolution of grain structures and second phases of a Mg-9.5Gd-4Y–2Zn-0.3Zr alloy during two-stage deformation that took place in the metal during hot extrusion, as well as their effects on its mechanical properties. We found that the alloy exhibited a bimodal grain structure consisting of equiaxed dynamic recrystallized (DRXed) grains and elongated unDRXed grains. As the extrusion process progressed, DRX occurred on a large scale, resulting in an increase in the proportion of DRXed grains from 17.8% to 93.2%, and a reduction in average grain size from 80.3 μm to 9.41 μm. The grain orientation also underwent a transition from a single orientation of an extrusion direction (ED) parallel to <0001> (i.e. ED//<0001>) to mixed orientations of ED//<01–10> and ED//<0001>. The primary mechanism of dynamic recrystallization (DRX) during extrusion involved particle-stimulated nucleation (PSN) accompanied by both continuous and discontinuous DRX. The Mg-9.5Gd-4Y–2Zn-0.3Zr alloy mainly contained intergranular 18R-long period stacking order (LPSO) phases and intragranular 14H-LPSO. As the extrusion process progressed, 18R-LPSO changed from blocky to lamellar to accommodate deformation, and β-Mg5(Gd,Y) phase particles dynamically precipitated along DRXed grain boundaries. The 14H-LPSO phase was found to be primarily distributed within coarse unDRXed grains. As deformation via extrusion progressed, the quantity of 14H-LPSO gradually decreased. Ultimately, with the gradual dissolution of Mg5(Gd,Y), 14H-LPSO reprecipitated within the recrystallized grain boundaries. As the extrusion process progressed, both the yield strength (YS) and elongation (EL) increased from 132.6 MPa to 287.6 MPa and from 10.8% to 15.5%, respectively. This was mainly attributed to the significant reduction in grain size and second phase size.

Synaptic dynamics linked to widespread elevation of H-reflex before peripheral denervation in amyotrophic lateral sclerosis.

Changes in Hoffmann reflex (H-reflex) exhibit heterogeneity among patients with amyotrophic lateral sclerosis (ALS), likely due to phenotype diversity. Current knowledge primarily focuses on soleus H-reflex, which may demonstrate an initial increase before subsequent decline throughout the disease course. The main objective was to investigate other muscles, to determine whether H-reflex changes could be associated with patient phenotype (onset site, functional disabilities). Additional experiments were performed to elucidate the neurophysiological mechanisms underlying H-reflex modifications. In age- and sex-matched groups of controls and patients, we compared H-reflex recruitment curves in soleus, quadriceps, and forearm flexors. Additionally, we examined H-reflex and motor evoked potential (MEP) recruitment curves in quadriceps. Last, to assess potential changes in monosynaptic excitatory post-synaptic potentials (EPSPs) of both peripheral and cortical origins, we analyzed peri-stimulus time histograms (PSTH) and peristimulus frequencygrams (PSF) of single motor units, along with H-reflex occurrence after paired pulse stimuli. The ratio between maximal amplitudes of H-reflex and direct motor response increased in all muscles, irrespective of disease onset, and was found positively correlated with exaggerated osteotendinous reflexes and spasticity, but depressed in patients on-riluzole. This finding was accompanied by a reduction in MEP size and no changes in PSTH, PSF, and paired-pulse H-reflex probability. It is speculated that spinal interneurons may compensate for potential depression of monosynaptic EPSPs in ALS. From a clinical perspective, while the added value of H-reflex to osteotendinous reflex evaluation may be limited, it can serve as a valuable quantitative biomarker of pyramidal dysfunction in clinical trials.

Parallel Lossless Compression of Raw Bayer Images on FPGA-Based High-Speed Camera

Digital image compression is applied to reduce camera bandwidth and storage requirements, but real-time lossless compression on a high-speed high-resolution camera is a challenging task. The article presents hardware implementation of a Bayer colour filter array lossless image compression algorithm on an FPGA-based camera. The compression algorithm reduces colour and spatial redundancy and employs Golomb–Rice entropy coding. A rule limiting the maximum code length is introduced for the edge cases. The proposed algorithm is based on integer operators for efficient hardware implementation. The algorithm is first verified as a C++ model and later implemented on AMD-Xilinx Zynq UltraScale+ device using VHDL. An effective tree-like pipeline structure is proposed to concatenate codes of compressed pixel data to generate a bitstream representing data of 16 parallel pixels. The proposed parallel compression achieves up to 56% reduction in image size for high-resolution images. Pipelined implementation without any state machine ensures operating frequencies up to 320 MHz. Parallelised operation on 16 pixels effectively increases data throughput to 40 Gbit/s while keeping the total memory requirements low due to real-time processing.

Modulation of the tumor microenvironment in non-muscle-invasive bladder cancer by OncoTherad® (MRB-CFI-1) nanoimmunotherapy: effects on tumor-associated macrophages, tumor-infiltrating lymphocytes, and monoamine oxidases.

Non-muscle-invasive bladder cancer (NMIBC) presents management challenges due to its high recurrence rate and a complex tumor microenvironment (TME). This study investigated the effects of OncoTherad® (MRB-CFI1) nanoimmunotherapy on the TME of BCG-unresponsive NMIBC, focusing on alterations in monoamine oxidases (MAO-A and MAO-B) and immune markers: CD163, FOXP3, CD8, and CX3CR1. A comparative analysis of immunoreactivities was made before and after OncoTherad® treatment and an immune score (IS) was established to evaluate the correlation between immunological changes and clinical outcomes. Forty bladder biopsies of twenty patients were divided into 2 groups (n = 20/group): 1 (pre-treatment biopsies); and 2 (post-treatment biopsies). Our results showed stable MAO-A levels but a significant (p < 0.05) decrease in MAO-B immunoreactivity after treatment, suggesting OncoTherad®'s efficacy in targeting the tumor-promoting and immunosuppressive functions of MAO-B. Significant (p < 0.05) reductions in CD163 and FOXP3 immunoreactivities were seen in post-treatment biopsies, indicating a decreased presence of M2 macrophages and Tregs. Corroborating with these results, we observed reductions in tumor histological grading, focality and size, factors that collectively enhanced recurrence-free survival (RFS) and pathological complete response (PCR). Moreover, elevated IFN-γ immunoreactivities in treated biopsies correlated with increased counts of CD8+ T cells and higher CX3CR1 expression, underscoring OncoTherad®'s enhancement of cytotoxic T cell functionality and overall antitumor immunity. The IS revealed improvements in immune responses post-treatment, with higher scores associated with better RFS and PCR outcomes. These findings validate OncoTherad®'s capability to modify the bladder cancer microenvironment favorably, promoting effective immune surveillance and response.

Neuroprotective Potential of Ethoxzolamide Targeting Oxidative Stress and Inflammation in Experimental Models of Intracerebral Hemorrhage.

As antioxidant and anti-inflammatory agents, carbonic anhydrase inhibitors can exert potentially useful therapeutic effects following central nervous system trauma, including intracerebral hemorrhage (ICH). However, the therapeutic efficacy of ethoxyzolamide (ETZ) as a novel carbonic anhydrase inhibitor for ICH has not yet been determined. An autologous blood injection method was used to establish ICH models, which were then used to establish the effects of intraperitoneal injection of ETZ on ICH. Neuronal damage, apoptotic protein expression, oxidative and inflammatory factor content, microglia marker Iba-1 positivity, hepatic and renal pathological changes, and serum concentrations of hepatic and renal function indices were assessed by Nissl staining, western blotting, enzyme-linked immunosorbent assay (ELISA), immunohistochemistry, hematoxylin and eosin (HE) staining, and automatic biochemical analysis in brain tissues. The ICH group showed massive hemorrhagic foci; significant increases in brain water content, modified mouse neurological deficit scoring (mNSS) score, pro-apoptotic protein expression, oxidative factors, pro-inflammatory factors, and Iba-1 positivity; and significant reductions in Nissl body size, anti-apoptotic protein expression, and antioxidant factors, all of which were reversed by ETZ in a dose-dependent manner. ETZ has a good biosafety profile with no significant burden on the human liver or kidneys. The Kelch-like ECH-associated protein 1 (Keap1)/nuclear factor erythroid 2-related factor 2 (Nrf2) pathway was mildly activated in ICH mice, and was further increased after ETZ injection. Molecular docking experiments revealed that ETZ could dock onto the Nrf2-binding domain of keap1. ETZ, as a novel carbonic anhydrase inhibitor, further activated the Keap1/Nrf2 pathway by docking with the Nrf2-binding domain of keap1, thereby exerting antioxidant, anti-inflammatory, anti-apoptotic, and cerebral neuroprotective effects in ICH mice.

Microstructure, phase compositions, and coercivity evolution in micron-thick SmCo-based permanent magnetic films

Permanent magnetic thick films are increasingly used in Micro-Electro-Mechanical Systems (MEMS) devices, but the interplay between magnetic properties, microstructure, and film thickness remains underexplored. We deposited SmCo-based films with thicknesses ranging from 350 nm to 1300 nm using magnetron sputtering at room temperature, followed by in-situ annealing. Our study examined the evolution of microstructure, phase composition, magnetic properties, and domain structures as thickness increases. The films displayed dense, fibrous structures typical of the zone T-type region, with 3D morphologies forming a network structure and an arc-shaped surface that expands with thickness. At thinner levels (around 350 nm), an amorphous SmCo phase predominates, prone to oxidation, while at greater thicknesses, the SmCo5 phase dominates but maintains a grain size of 12–15 nm. Coercivity decreases significantly from 33 kOe to 8 kOe as thickness increases from 630 to 1300 nm due to the diminishing pinning effect and dominance of the reversal domain nucleation mechanism. Analysis using magnetic force microscopy and micromagnetic simulations indicates that this reduction in coercivity is mainly due to the decomposition of the SmCo5 phase and a reduction in magnetic domain size.

LONG-TERM SURVIVAL OF TANYCYTIC EPENDYMOMA OF LATERAL VENTRICLE WITH ADJACENT FRONTAL LOBE INVASION: CASE REPORT AND LITERATURE REVIEW

Abstract AIMS Tanycytic ependymoma (TE) of lateral ventricle is a rare variant of ependymoma often challenging to diagnose due to its distinctive histological features and similarity to other central nervous system neoplasms. This report presents a case of TE in a 48 years-old lady with 20 years of long-term survival and provides a comprehensive review of the literature to elucidate the clinical, radiological, and pathological characteristics of this entity. METHOD A 48-year-old woman presented with a left lateral ventricular tumor invading the left frontal lobe and pericallosal region, subsequently diagnosed as TE after stereotactic biopsy followed by radical radiotherapy. Epidemiological features, preoperative and postoperative radiological surveillance, and functional performance after adjuvant radiotherapy were reviewed. Additionally, we review the current literature to explore current perspective of TE. Three major medical database engines, PubMed (Medline), Scopus (ELSEVIER), and Cochrane were used to conduct a thorough literature search. RESULTS The patient exhibited notable neurological improvement following stereotactic biopsy and radical radiotherapy, with long-term surveillance demonstrating stability and reduction in tumor size over a 20-year period. Our literature review underscores the rarity of TE and its diagnostic challenges, emphasizing the importance of histopathological examination and immunohistochemical analysis for accurate diagnosis. TE exhibit unique ultrastructural features, requiring meticulous examination for proper classification. Additionally, we discuss the implications of TE’s histological resemblance to other intramedullary tumors and its potential impact on therapeutic decisions. CONCLUSION Tanycytic ependymomas pose diagnostic dilemmas due to their morphological overlap with other CNS tumors. However, heightened awareness among clinicians and pathologists is crucial for accurate identification and appropriate management. Further research into the molecular mechanisms underlying TE is warranted to enhance diagnostic precision and refine treatment strategies, ultimately improving patient outcomes.

Improving the Energy Storage Performance in Bi0.5Na0.5TiO3-Based Ceramics by Combining Relaxor and Antiferroelectric Properties.

Ceramic capacitors have received great attention for use in pulse power systems owing to their ultra-fast charge-discharge rate, good temperature stability, and excellent fatigue resistance. However, the low energy storage density and low breakdown strength (BDS) of ceramic capacitors limit the practical applications of energy storage technologies. In this work, we present a series of relaxor ferroelectric ceramics (1-x) [0.94 Bi0.5Na0.5TiO3 -0.06BaTiO3]- x Sr0.7Bi0.2TiO3 (1-x BNT-BT- x SBT; x = 0, 0.20, 0.225, 0.25, 0.275 and 0.30) with improved energy storage performances by combining relaxor and antiferroelectric properties. XRD, Raman spectra, and SEM characterizations of BNT-BT-SBT ceramics revealed a rhombohedral-tetragonal phase, highly dynamic polar nanoregions, and a reduction in grain size with a homogeneous and dense microstructure, respectively. A high dielectric constant of 1654 at 1 kHz and low remnant polarization of 1.39 µC/cm2 were obtained with the addition of SBT for x = 0.275; these are beneficial for improving energy storage performance. The diffuse phase transition of these ceramics displays relaxor behavior, which is improved with SBT and confirmed by modified the Curie-Weiss law. The combining relaxor and antiferroelectric properties with fine grain size by the incorporation of SBT enables an enhanced maximum polarization of a minimized P-E loop, leading to an improved BDS. As a result, a high recoverable energy density Wrec of 1.02 J/cm3 and a high energy efficiency η of 75.98% at 89 kV/cm were achieved for an optimum composition of 0.725 [0.94BNT-0.06BT]-0.275 SBT. These results demonstrate that BNT-based relaxor ferroelectric ceramics are good candidates for next-generation ceramic capacitors and offer a potential strategy for exploiting novel high-performance ceramic materials.

Application of a novel auxiliary collector for molybdenite fines recovery in sustainable froth flotation production: Combining DFT calculations and experiments

The recovery of molybdenite diminishes with a reduction in particle size, which causes serious resource waste and financial loss. In this work, 1-dodecanethiol (NDM) was explored as an auxiliary collector to enhance the flotation of molybdenite fines. The flotation performance and adsorption mechanisms were revealed by micro-flotation tests, Zeta potential, contact angle, X-ray Photoelectron Spectroscopy (XPS), and density functional theory (DFT) calculations. Economic and environmental risks were assessed by industrial-scale flotation tests. The micro-flotation tests showed that NDM was more effective in improving the recovery of the −20 μm grade compared to the −38+20 μm grade. Zeta potential and contact angle results indicated that NDM significantly enhanced the hydrophobicity of the finer-grained molybdenite surface. XPS and DFT calculations revealed that water molecules acted as a significant barrier to kerosene adsorption, and NDM overcame this limitation by selectively adsorbing on the edge of molybdenite. The economic and environmental assessment indicated that NDM increased monthly product profits by $319,283.38 and was environmentally friendly, which can be extensively employed for mineral sources with similar mineralogical properties.

PFAS-mediated disruptions on thyroid histology

Abstract Introduction/Objective Per-and polyfluroalkyl substances (PFAS), are environmental contaminants of emerging concern due to their abundance in the environment and potential adverse health impacts. PFAS are used in waterproof clothing, makeup, carpets, upholstery, cookware, and fast-food containers. These organic pollutants have been found in the blood of 98% of Americans and have been linked to disruption in thyroid hormones. During fetal life, thyroid hormones are crucial for brain development and alterations in these hormones can induce long-term impacts on intellectual and brain impairments. T3 and T4 are known to be altered by PFAS exposure, but the mechanism by which this is done remains unclear. Methods/Case Report Normal thyroid cells were treated for 72 hours with 1000 nM solution containing either GEnX, PFOA, PFOS, or 1% DMSO control. Immunofluorescence for actin, tubulin, and DAPI was performed using a Nikon spinning disk. In vivo studies where 8-week-old mice are gavaged with 7.5 mg/kg of PFOS, PFOA, and GenX or PBS control for 8 weeks. Results (if a Case Study enter NA) We hypothesized the PFAS treatment alters thyroid cells morphology and histology. Immunofluorescence staining of normal thyroid cells treated with PFAS show a decrease in actin stress fibers compared to control cells. PFAS treated mice show a decrease in follicle size compared to control (average 1017 um2 size, p=0.0483). Conclusion This is the first study to show changes in thyroid histology after 8 weeks of PFAS exposure. As structure and function are closely linked, it is likely that this reduction in follicle size and actin reorganization contribute to alterations in thyroid function. Future studies are needed to illuminate the mechanism by which PFAS alter thyroid function in vivo. Understanding the role of PFAS-mediated thyroid dysregulation will have far reaching implications on environmental regulations and considerations for limiting PFAS in our environment.

Design and manufacture of an ultra-compact, 1.5 T class, controlled-contact resistance, REBCO, brain imaging MRI magnet

Abstract Brain imaging MRI comprises a significant proportion of MRI scans, but the requirement for including the shoulders in the magnet bore means there is not a significant size reduction in the magnet compared to whole-body magnets. Here we present a new design approach for brain imaging MRI magnets targeting ±20 kHz B 0 variation over the imaging volume rather than the more usual ±200 Hz making use of novel high-bandwidth MRI pulse sequences and distortion correction. Using this design approach, we designed and manufactured a 1.5 T class ReBCO cryogen-free magnet. The magnet is dome-like in form, completely excludes the shoulders and is &lt;400 mm long. The magnet was wound using no-insulation style coils with a conductive epoxy encapsulant where the contact resistance of the coils was controlled so the emergency shut-down time of the magnet was less than 30 s. Despite acceptable coil testing results ahead of manufacture, during testing of the magnet, several of the epoxy coils showed signs of damage limiting stable performance to &lt;55 A compared to the designed 160 A. These coils were replaced with insulated paraffin encapsulated coils. Subsequently the magnet was re-ramped and was stable at 81 A, generating 0.71 T as several other coils had sustained damage not visible in the first magnet iteration. The magnet has been passive shimmed to ±20 kHz B 0 variation over the imaging volume and integrated into an MRI scanner. The stability of the magnet has been evaluated and found to be acceptable for MRI.

Toward Water-Resistant, Tunable Perovskite Absorbers Using Peptide Hydrogel Additives.

In recent years, hydrogels have been demonstrated as simple and cheap additives to improve the optical properties and material stability of organometal halide perovskites (OHPs), with most research centered on the use of hydrophilic, petrochemical-derived polymers. Here, we investigate the role of a peptide hydrogel in passivating defect sites and improving the stability of methylammonium lead iodide (MAPI, CH3NH3PbI3) using closely controlled, in situ X-ray photoelectron spectroscopy (XPS) techniques under realistic pressures. Optical measurements reveal that a reduction in the density of defect sites is achieved by incorporating peptide into the precursor solution during the conventional one-step MAPI fabrication approach. Increasing the concentration of peptide is shown to reduce the MAPI crystallite size, attributed to a reduction in hydrogel pore size, and a concomitant increase in the optical bandgap is shown to be consistent with that expected due to quantum size effects. Encapsulation of MAPI crystallites is further evidenced by XPS quantification, which demonstrates that the surface stoichiometry differs little from the expected nominal values for a homogeneously mixed system. In situ XPS demonstrates that thermally induced degradation in a vacuum is reduced by the inclusion of peptide, and near-ambient pressure XPS (NAP-XPS) reveals that this enhancement is partially retained at 9 mbar water vapor pressure, with a reduced loss of methylammonium (MA+) from the surface following heating achieved using 3 wt % peptide loading. A maximum power conversion efficiency (PCE) of 16.6% was achieved with a peptide loading of 3 wt %, compared with 15.9% from a 0 wt % device, the former maintaining 81% of its best efficiency over 480 h storage at 35% relative humidity (RH), compared with 48% maintained by a 0 wt % device.

Characterizing randomness in parameterized quantum circuits through expressibility and average entanglement

Abstract While scalable error correction schemes and fault tolerant quantum computing seem not to be universally accessible in the near sight, the efforts of many researchers have been directed to the exploration of the contemporary available quantum hardware. Due to these limitations, the depth and dimension of the possible quantum circuits are restricted. This motivates the study of circuits with parameterized operations that can be classically optimized in hybrid methods as variational quantum algorithms, enabling the reduction of circuit depth and size. The characteristics of these Parameterized Quantum Circuits (PQCs) are still not fully understood outside the scope of their principal application, motivating the study of their intrinsic properties. In this work, we analyse the generation of random states in PQCs under restrictions on the qubits connectivities, justified by different quantum computer architectures. We apply the expressibility quantifier and the average entanglement as diagnostics for the characteristics of the generated states and classify the circuits depending on the topology of the quantum computer where they can be implemented. As a function of the number of layers and qubits, circuits following a Ring topology will have the highest entanglement and expressibility values, followed by Linear/All-to-all almost together and the Star topology. In addition to the characterization of the differences between the entanglement and expressibility of these circuits, we also place a connection between how steep is the increase on the uniformity of the distribution of the generated states and the generation of entanglement. Circuits generating average and standard deviation for entanglement closer to values obtained with the truly uniformly random ensemble of unitaries present a steeper evolution when compared to others.

Navigating 'grey areas' and challenges during evaluation of transplant eligibility in specific myelofibrosis populations: a perspective on behalf of the Chronic Malignancies Working Party of the EBMT.

Significant efforts have been made to effectively select myelofibrosis (MF) patients who can benefit from allogeneic hematopoietic cell transplantation (allo-HCT), the only current cure for MF. The recent EBMT/ELN 2024 recommendations offer valuable guidance for hematologists and transplant physicians. However, several grey areas remain in day-to-day clinical practice regarding the feasibility and optimal preparation for transplantation in patients with this disease. Effective spleen size reduction, often achieved with JAK inhibitors, appears crucial for transplant success. For resistant cases, switching JAK inhibitors, splenectomy, or spleen irradiation may be considered, taking into account patient profiles, treatment availability and center preferences. Managing splanchnic vein thromboses, portal, and pulmonary hypertension is critical as these conditions may affect transplant outcomes. Cytopenias, particularly transfusion-dependent anemia and thrombocytopenia, complicate treatment and impact on outcomes, though new drugs show promise. Comorbidities play a significant role and tools like the Hematopoietic Cell Transplantation-Comorbidity Index (HCT-CI) and frailty assessments are useful for evaluating transplant risks while allowing the implementation of corrective measures. Especially in low- and medium-income countries where access to novel therapies may be challenging, allo-HCT still represents an attractive therapeutic option for MF. Future directions include integrating new therapeutics into the transplant algorithm and leveraging artificial intelligence for more informed risk assessment, highlighting the need for tailored approaches to improve allo-HCT outcomes in such a setting.

Enhanced hydrophobicity of polyurethane coating for steel protection through replication and nanomaterial integration

Polyurethanes (PU) are widely used in corrosion protection, anti-biofouling coatings, and self-cleaning glass, yet their low hydrophobicity poses durability challenges. This study addresses this by enhancing PU coatings’ hydrophobicity by refining surface roughness and forming tailored porous structures. Using drop, spin, dip, and spray coating techniques, hydrophobic PU coatings were fabricated on 304 steel plates. To further enhance hydrophobicity, 0.5 w/v% graphene nanoplatelets (GNP) were introduced into the coatings. Additionally, stainless-steel 500 mesh was incorporated to create patterned surfaces, increasing surface roughness and tailoring the porous structure. The analysis included optical and scanning electron microscopy, water contact angle (WCA) measurements, Fourier transform infrared spectroscopy, electrochemical corrosion tests, and atomic force microscopy. Incorporating GNP notably increased WCA by 20–23° and reduced corrosion rates in a 3.5% NaCl solution. Likewise, applying stainless-steel mesh improved surface roughness, raising WCA by 3-8° and decreasing corrosion rates. The study observed changes in porous structure, with pore size reduction correlating with increased roughness and decreased corrosion rates upon mesh application and GNP addition. This comprehensive examination highlights the potential of PU coatings for various applications and underlines the importance of tailored porous structures in enhancing their performance and versatility. Spin coating emerged as the optimal technique, yielding uniform, defect-free coatings with the highest WCA.