Silicon Nanowires Research Articles

Paper‐like 100% Si Nanowires Electrodes Integrated with Argyrodite Li6PS5Cl Solid Electrolyte

Silicon anodes are a promising solution in all‐solid‐state batteries (ASSBs) due to minor lithium dendrite risk, high capacity, and low potential. Research on Si integration in ASSBs is still nascent, requiring a deep understanding of the interplay between electrode composition, structure, and performance. Here, we present the first study on 100% Si nanowires integrated with Li6PS5Cl solid electrolyte (SE). The anodes are paper‐like networks of aggregated Si nanowires produced by a slurry‐free method without carbon/binders. Despite the lack of any conductor, the Si anodes provide >2.5 Ah/g capacity at a high mass loading of 1.7 mg/cm2(~5 mAh/cm2), demonstrating sufficient electric and ionic conductivities. Electro‐chemo‐mechanical properties of the electrodes over (de)lithiation were probed through electrochemical impedance spectroscopy, ex‐situ microscopy, and in‐operando pressure regulation measurements. The lithiated electrode/SE interface was found to be electrochemically stable. Cross‐sectional microscopy at various states‐of‐charge confirmed the buffering effect of the anode porosity, resulting in the preservation of the electrode’s thickness after the first lithiation but a considerable shrinkage during delithiation, producing cracking and formation of the new interface. Capacity remains constant for five cycles, then decreases linearly up to 40 cycles. This is attributed to repeated fracture of the anode/electrolyte interface and the corresponding impedance increase

A red-light-powered silicon nanowire biophotochemical diode for simultaneous CO2 reduction and glycerol valorization

A red-light-powered silicon nanowire biophotochemical diode for simultaneous CO2 reduction and glycerol valorization

Au Nanoparticles@Si Nanowire Oligomer Arrays for SERS: Dimers Are Best.

We report the synthesis of vertically aligned silicon nanowire (VA-SiNW) oligomer arrays coated with Au nanoparticle (NP) monolayers via a combination of colloidal lithography, metal-assisted chemical etching, and directed NP assembly. Arrays of SiNW monomers (i.e., isolated NWs), dimers, and tetramers are synthesized, decorated with AuNPs, and tested for their performance in surface-enhanced Raman spectroscopy. The ∼20 nm AuNPs easily enter within the ca. 40 nm gaps of the SiNW oligomers, thus reaching the hot spot region. At 785 nm excitation, the AuNPs@SiNW dimer arrays provide the highest Raman signal, in agreement with electromagnetic simulations showing a high electric field enhancement at the Au/Si interface within the dimer gap region.

Analytical Photoresponses of Gated Nanowire Photoconductors.

Low-dimensional photoconductors have extraordinarily high photoresponse and gain, which can be modulated by gate voltages as shown in literature. However, the physics of gate modulation remains elusive. In this work, the physics of gate modulation in silicon nanowire photoconductors with the analytical photoresponse equations is investigated. It is found that the impact of gate voltage varies vastly for nanowires with different size. For the wide nanowires that cannot be pinched off by high gate voltage, it is found that the photoresponses are enhanced by at least one order of magnitude due to the gate-induced electric passivation. For narrow nanowires that starts with a pinched-off channel, the gate voltage has no electric passivation effect but increases the potential barrier between source and drain, resulting in a decrease in dark and photocurrent. For the nanowires with an intermediate size, the channel is continuous but can be pinched off by a high gate voltage. The photoresponsivity and photodetectivity is maximized during the transition from the continuous channel to the pinched-off one. This work provides important insights on how to design high-performance photoconductors.

Urea adsorption and detection using silicon nanowires doped with B, Al, C, Ge, N, and P: A DFT investigation

Urea can serve as a biomarker for the detection of various illnesses, including renal and hepatic failure. Consequently, the development of novel devices and materials capable of adsorbing and identifying urea is a crucial objective for the scientific community. This study theoretically investigates the adsorption and detection capabilities of doped silicon nanowires (SiNWs) for urea using Density Functional Theory (DFT). Doping involves substituting a silicon atom on the surface with a dopant atom; B, Al, C, Ge, N, and P were employed for this purpose. This study presents an innovative method for enhancing urea adsorption and detection by doping SiNWs with group XIII elements, specifically aluminum and boron atoms. The results indicate that this doping significantly improves urea adsorption on SiNWs compared to undoped SiNWs. Notable changes in the bandgaps and work functions of the doped nanowires following urea adsorption suggest their potential use as diagnostic tools for uremia.

Tunnel transport problem for open multilayer nitride nanostructures with an applied constant magnetic field and time-dependent potential: An exact solution

A quantum mechanical theory for description of electronic quasistationary states in two-dimensional (2D) layered semiconductor nanostructure was developed. A constant external magnetic field B was directed along semiconductor layers. The presence of internal electric fields F originated from the potential barriers and wells in semiconductor layers was taken into account. The vector of F was directed perpendicularly to semiconductor layers. The interaction of tunneled electrons with a time-dependent electromagnetic fields was analyzed in detail. An approach to obtain an exact solution to the problem based on a combination of the Lewis-Riesenfeld method for complete Schrödinger equation and scattering theory was developed. Application of the scattering theory in combination with the -matrix and transfer-matrix methods allowed us to calculate the electron quasistationary spectra. Effects of magnetic field on the resonant energy and width of electronic quasistationary states as well as on the electronic conductivity were also discussed. Published by the American Physical Society 2024

Spatial analysis of multi-frequency SAW beams excited by slanted IDTs on ZnO-SiC heterostructures

Slanted (or fan-shaped) interdigital transducers (IDTs) with broadband response allow the selective excitation of surface acoustic waves (SAWs) with narrow beam widths and pathways controlled by the excitation frequency. Such SAW-based spatial and frequency control is important for applications in microfluidics, as well as in emerging applications in semiconductor nanostructures. In this contribution, we generate both Rayleigh and Sezawa modes with slanted IDTs on a 4H-SiC substrate coated with a piezoelectric ZnO film. We directly measure the phase wavefronts of narrow SAW beams in the 1200–1260 MHz frequency bandwidth using high-resolution ( <1μm ) optical interferometry, and discuss the mechanisms that directly affect the propagation direction and phase profiles of the SAW beams. The combination of multimodal and multi-frequency SAW delay lines provides rich opportunities for SAW-based control of low-dimensional systems, such as electrons in epitaxial graphene or spin centers near the surface of the SiC substrates.

Model and performance analysis of energy conversion in functionally graded flexoelectric semiconductor nanostructures

Energy systems converting efficiently from surrounding environment for powering semiconductor electronic components at nanoscale has attracted intense research interests. Due to the strong size dependency, flexoelectricity has been demonstrated as an excellent candidate implemented as nanoscale piezoelectric semiconductor energy harvesters. In this work, through a judicious exploitation of structural symmetry and nonuniformity, we theoretically study the energy conversion behaviors of a novel asymmetric nanodisk model composed of functionally graded (FG) flexoelectric semiconductor (FS) (FG-FS) materials while being loaded with thickness-extensional mechanical vibration. In numerical analysis, the material parameters have been treated with a general variation method under the Cartesian coordinate systems for simplicity. Taking into accounts of the nonuniform structural form and multi-field coupling features, we derived an octic governing equation with variable coefficients for the current analyzed FG-FS nanodisk structure, which is, however, almost impossible to obtain analytical solutions. To successfully address this issue and also further explore the improved performance and new phenomena induced by the FG type of non-uniform structural profile, we specially proposed an efficient tensor algorithm and reduced the octic governing equation into one quartic equation with variable coefficients and other four common quadratic equations. Later, we explicitly explored the effect of each physical parameter on the energy conversion performance of the FS energy harvester by studying the variations of the output electric power density and the energy conversion efficiency. Results illustrated that the electromechanical energy conversion behaviors of the studied FG-FS nanodisk can be properly tuned by not only the related material parameters but also their gradations. We believe our work have the potential to pave new way for the designs and manufacture of novel nano-electronic semiconductor components for the future practical applications.

Atomistic wave packet investigation of phonon scattering at rough surfaces

Investigating the phonon-surface scattering mechanism is essential for the evaluation of thermal transport in nanostructures. The theoretical description to quantify this mechanism remains to be developed at the atomic scale. This work presents a phonon wave packet method to study the phonon-surface scattering behavior at rough surfaces. We obtain the specularity distribution dependent on phonon polarization, wavelength, and surface roughness. The reflection of the diffuse wave packet is primarily attributed to the surface shadowing effect at a higher incident angle, surface disorder, and surface-induced localized modes. Taking the wavevector-dependent specularity data as input, the thermal conductivity of silicon nanowires is calculated based on the Boltzmann Transport Equation. Our specularity model provides an accurate evaluation for predicting thermal conductivity. This work offers an atomic-level analysis for phonon-surface interaction, which is helpful for the understanding of thermal transport in nanostructures.

Optical, dielectric and photoelectrochemical performances of the CeO2/silicon nanowire system: Studying the silicon nanowire length effect on the photodegradation of rhodamine B

Optical, dielectric and photoelectrochemical performances of the CeO2/silicon nanowire system: Studying the silicon nanowire length effect on the photodegradation of rhodamine B

Self-power, multiwavelength photodetector based on a Sn-doped Ge quantum dots/hexagonal silicon nanowire heterostructure.

Tin-doped germanium quantum dots (Sn-doped Ge QDs)-decorated hexagonal silicon nanowires (h-Si NWs) were adopted to overcome the low infrared response of silicon and the excess dark current of germanium. High-quality Sn-doped Ge QDs with a narrow bandgap can be achieved through Ge-Sn co-sputtering on silicon nanowires by reducing the contact area between heterojunction materials and Sn-induced germanium crystallization. The absorption limit of the heterostructure is extended to 2.2 µm, and it is sensitive to 375-1550 nm light at 0 V, which has optimality at 1342 nm, with a photo-to-dark current ratio of over 815, a responsivity of 0.154 A/W, and a response time of 0.93 ms. The superior performance of the Sn-doped Ge QDs/h-Si NW photodetector in multiwavelength is attractive for multi-scenario applications.

Electrically‐Driven Light Source Embedded in a GaP Nanowaveguide for Visible‐Range Photonics on Chip

AbstractThe key components of photonic integrated circuits are nanoscale optica emitters and nanowaveguides. III‐V semiconductor nanostructures are considered as the most promising material platform for these components due to highly efficient luminescence and high refractive index, but the problem of emission coupling with waveguide is to be solved. In this work, the use of GaP nanowires (NWs) with different types of doping (GaP:Si or GaP:Be) is proposed as optical waveguides with directly integrated electrically‐driven light sources, solving the problem of emission‐to‐waveguide coupling. Single NWs are integrated with electrodes and pump electroluminescence by a tunnel junction allowing to study emission properties with nanoscale spatial resolution. Basing on the experiments on scanning tunnelling microscopy (STM), electron microscopy, time‐resolved photoluminescence micro‐spectroscopy, X‐ray diffraction, and STM‐induced electroluminescence, it is proven that GaP NWs exhibit different integrated light‐source on doping type of NWs. GaP:Be NWs contain inclusion of the crystalline wurtzite phase with a direct bandgap, and, thus, these NW regions can be considered as electrically‐driven nanoscale sources of light monolithically integrated into GaP NW‐based waveguides. Meanwhile, GaP:Si NWs work as optical waveguides capable of efficient light generation over the entire length of NW. The developed designs are promising for construction of integrated photonic circuits.

Stable and Tunable Quantum Conductance in Spider-Silk-like Synaptic Device for Neurocomputing.

The quantum conductance (QC) behaviors in synaptic devices with stable and tunable conductance states are essential for high-density storage and brain-like neurocomputing (NC). In this work, inspired by the discontinuous transport of fluid in spider silk, a synaptic device composed of a silicon oxide nanowire network embedded with silicon quantum dots (Si-QDs@SiOx) is designed. The tunable QC behaviors are achieved in both the SET and RESET processes, and the QC states exhibit stable retention time exceeding 104 s in the synaptic device and show stable reproducibility after an interval of two months. The synaptic plasticity, including long-term potentiation/depression and Pavlovian conditioning function, is simulated based on the tunable conductance. The mechanism of stable and tunable QC behaviors is analyzed and clarified by beading effect of spider silk in Si-QDs@SiOx nanowires structure. The digit recognition capability of the device is evaluated by simulation using an artificial neural network consisting of the Si-QDs@SiOx-based synaptic device. These results provide insights into the development of neurocomputing systems with high classification accuracy.

Shedding light on evolution of Raman line shape with probing laser power: Light-induced perturbation in electron-phonon coupling.

The laser power mediated changes in the Raman line shape have been considered in terms of interference between discrete phonon states ρ and the electronic continuum states ϰ contributed by Urbach tail states. The laser-induced effects are treated in terms of the increase in the surface temperature and thereby the scaling of electronic disorder, i.e., Urbach energy, which can further contribute to the electron-phonon interactions. Therefore, the visualization of this effect is attempted analytically as a perturbation term in the Hamiltonian, which clearly accounts for the observed changes with laser power. This has been investigated based on the experimental results of laser power dependent Raman spectra of bulk EuFeO3 and silicon nanowires, which are found to provide convincing interpretations.

ZnO:CuO Composites Obtained by Rapid Joule Heating for Photocatalysis.

Semiconductor oxides belonging to various families are ideal candidates for application in photocatalytic processes. One of the challenges facing photocatalytic processes today is improving their efficiency under sunlight irradiation. In this study, the growth and characterization of semiconductor oxide nanostructures and composites based on the ZnO and CuO families are proposed. The selected growth method is the resistive heating of Zn and Cu wires to produce the corresponding oxides, combined with galvanic corrosion of Zn. An exhaustive characterization of the materials obtained has been carried out using techniques based on scanning electron microscopy and optical spectroscopies. The method we have followed and the conditions used in this study present promising results, not only from a degradation efficiency point of view but also because it is a cheap, easy, and fast growth method. These characteristics are essential in order to scale the process beyond the laboratory.

Self-Driven Photodetectors Based on Flexible Silicon Nanowires Array Surface-Passivated With Tin-Based Perovskites

Self-Driven Photodetectors Based on Flexible Silicon Nanowires Array Surface-Passivated With Tin-Based Perovskites

Defect-mediated Fermi level modulation boosting photo-activity of spatially-ordered S-scheme heterojunction

Spatially-ordered S-scheme photocatalysts are intriguing due to their enhanced light harvesting, spatially isolated redox sites, and strong redox abilities. Nonetheless, heightening the performance of S-scheme photocatalysts via controllable defect engineering is still challenging to now. In this work, multi-armed MoSe2/CdS S-scheme heterojunction with intimate Mo-S bond coupling and adjustable Se vacancies (VSe) and Mo5+ concentrations was constructed, which consisted of few- or even single-layered MoSe2 growing on the {11–20} facets of wurtzite CdS arms. The S-scheme charge transmission mechanism of MoSe2/CdS heterojunction was validated by density functional theory calculation combined with in situ photo-irradiated X-ray photoelectron spectroscopy, surface photovoltage, and radical measurements. Moreover, the Fermi level gap between CdS and MoSe2 was enlarged by regulating the contents of donor (VSe) and acceptor (Mo5+) impurities with synthesis temperature, which strengthens the built-in electric field and carriers transfer driving force of MoSe2/CdS composites, contributing to an outstanding H2 evolution activity of 52.62 mmol·g−1·h−1 (corresponding to an apparent quantum efficiency of 34.8 % at 400 nm) under visible-light irradiation (λ > 400 nm), 25.8 times that of Pt-loaded CdS counterpart and a substantial amount of reported CdS-containing photocatalysts. Our study results are anticipated to facilitate the rational design of advanced semiconductor nanostructures for efficient solar conversion and utilization.

Investigation of the Bending Behavior in Silicon Nanowires: A Nanomechanical Modeling Perspective

Nanowires (NWs) play a crucial role across a wide range of disciplines such as nanoelectromechanical systems, nanoelectronics and energy applications. As NWs continue to reduce in dimensions, their mechanical properties are increasingly affected by surface attributes. This study conducts a comprehensive examination of nanomechanical models utilized for interpreting large deformations in the bending response of silicon NWs. Specifically, the Heidelberg, Hudson, Zhan, SimpZP and ExtZP nanomechanical models are explored regarding their capability to predict the elastic properties of silicon NWs with varying critical dimensions and crystal orientations. Molecular dynamics simulations are employed to model silicon NWs with unreconstructed surface states. The calculation of intrinsic stresses and the methodology for quantifying surface properties, including surface stresses and surface elasticity constants, are carried out using atomistic modeling. The findings reveal significant disparities of up to 100 GPa among nanomechanical models in interpreting a singular force-deflection response obtained for a silicon NW. Inadequate consideration of surface and intrinsic effects in nanomechanical modeling of NWs leads to substantial variability in their mechanical properties. This investigation yields valuable insights into the surface characteristics of silicon NWs, thereby enhancing our understanding of the essential role played by nanomechanical models in the intricate interpretation of mechanical properties at the nanoscale.

AFM interlaboratory comparison for nanodimensional metrology on silicon nanowires

Abstract Silicon nanowires (NWs) with a cylindrical form are fabricated by means of nanospheres lithography and metal-assisted chemical etching to obtain high aspect ratio nanostructures (diameter of about 100 nm and length of more than 15 µm) on cm2 area.&amp;#xD;The nanodimensional characterization of individual NWs is performed by using several techniques, because dimensions at the nanoscale strictly relate to functional performances. In this study, we report the results of an interlaboratory comparison between measurements from a metrological atomic force microscope (AFM) and research AFMs located in different national metrology institutes (NMIs) across Europe and in a university.&amp;#xD;The purpose of this study is to characterize two measurands: (i) sidewall roughness (Ra, Rq, Rz, Rsk, Rku parameters), extracted from the top profile measured along the nanowire length, and (ii) diameter of the nanowires measured as top-height. To this goal, the nanowires are spread horizontally on a silicon substrate, which has several areas labelled with a pattern of crosses and letters facilitating the measurement of the same NW, in order to study the reproducibility due to different instruments.&amp;#xD;Measurements show a good agreement between the different NMIs, with a combined standard uncertainty of top-height diameter less than 3%, and with a combined standard uncertainty of roughness parameters well within 5% for Ra and Rq values.

Envelope-function theory of inhomogeneous strain in semiconductor nanostructures

Envelope-function theory of inhomogeneous strain in semiconductor nanostructures