Single Phase Research Articles

Three phase microcontroller based automatic change-over selection switch

The significance of electricity in a developed country cannot be underestimated because power instability problem affects the economy growth, productivity and infrastructure development. The issues of phase failure, losses and phase imbalance earth fault are main causes that lead to unstable and erratic power supply. Most homes and office complexes where single-phase supply is needed are supplied with three phases of power supply to allow change from one phase to another when there is fluctuation or complete outage of power supply on a particular phase. This operation is normally done manually and has caused a setback in terms of time wastage, strenuous operation, susceptibility to fire outbreak, electric shock and high maintenance frequency. When voltage supply on a phase is below 220V or above 415V, this system automatically disconnects the load from the phase and connects to another where the required condition is met. Therefore, this paper presents a Microcontroller Based Automatic Transfer Switching System which is made up of voltage sensing circuit, Hall Effect current sensor, relays, LEDs and LCD of PIC16F877A microcontroller. A system flow chart was developed, programmed with MikroC software and simulated using Proteus electrical software design. A 10KVA single phase generator was used as alternate power source. The load capacity of the design was determined by decoupling Maxwell’s Equations of 8KW and power loss using pointing vector equation as 0.25% of the peak load. The switch is tested to have function optimally within ±5% nominal voltage of 220 - 415V supply and produced approximately 20 seconds elapses during the entire process of power supply changeover. Hence this device is suitable for Industrial and Domestic use where 3-phase power supply is available with a stand-by power source.

Quantum Voting Machine Encoded with Microwave Photons

Abstract We propose a simple quantum voting machine using microwave photon qubit encoding, based on a setup comprising multiple microwave cavities and a coupled superconducting flux qutrit. This approach primarily relies on a multi-control single-target quantum phase gate. The scheme offers operational simplicity, requiring only a single step, while ensuring verifiability through the measurement of a single qubit phase information to obtain the voting results. And it provides voter anonymity, as the voting outcome is solely tied to the total number of affirmative votes. Our quantum voting machine also has scalability in terms of the number of voters. Additionally, the physical realization of the quantum voting machine is general and not limited to circuit QED. Quantum voting machine can be implemented as long as the multi-control single-phase quantum phase gate is realized in other physical systems. Numerical simulations indicate the feasibility of this quantum voting machine within the current quantum technology.

Semi-Analytical Solution for a Single-Phase Thermal Conduction Problem of a Hollow Cylinder with a Growing or Receding Inner Radius

Abstract A semi-analytical solution for the thermal conduction of a single phase, homogeneous, circular, hollow-cylinder with a growing or receding inner radius at a constant rate under unit-loading was derived using conformal mapping, Laplace transformation, and a Zakian series representation of the inverse Laplace transform. All solutions allow for convection on the fixed outer radius. Predictions were compared to finite-element simulations with excellent agreement observed. Given the changing thickness, thermal transients could not reach true steady-state equilibrium, especially for faster growth or recession rates. Indeed, the temperature states become somewhat linear with respect to time, reflecting the constant velocity of growth or recession. In practice, the resulting solutions can be used to determine temperatures during machining, wear, erosion, corrosion, and/or additive manufacturing, especially for lower temperature solid-state methods such as cold-spray.

IMAGING OF BUBBLY FLOW USING ULTRASOUND

Flow measurement is a vital ‎issue in instrumentation and has been applied in the various industries. The characteristics of a single phase regime has been extensively researched. On the other hand obtaining the characteristics of a multi-component flow is more complex and traditional equipment do not provide ‎reliable results. As such, tomography utilizing non-invasive ‎transducers is getting attention in the industries because it does not invade the flow. Ultrasonic tomography is among the methods which is suitable for flow containing bubbles. In this project, 16 ultrasonic transducers are placed around a flow pipe. Five different phantoms representing solid flow are placed in the pipe. The flow is imaged using the linear back projection algorithm. The results show that the system was able to image the phantoms which are placed at different locations.

Photocatalytic Drug Degradation and Supercapacitor Applications of FeVO4 and rGO‐FeVO4 Nanocomposite

AbstractConstructing novel multifunctional materials is a promising approach to boost the catalytic activity and electrochemical performance simultaneously. Herein, hydrothermal synthesized FeVO4 nanosized particles dispersed on reduced graphene oxide (rGO) through cost‐effective simple sonochemical assisted route are developed as an efficient material for photocatalysis activity and high‐value‐added supercapacitor applications. The synthesized materials were characterized for structural and morphological purity and found to be in single phase and nanostructured. rGO‐FeVO4 composite shows excellent photodegradation of Levofloxacin (LVO) drug (100 % over 80 min) compared with FeVO4 owing to the bandgap in visible region and larger surface area. Further, the optimized rGO‐FeVO4 composite was employed into supercapacitors and it showed 3 times higher capacitance (211.4 F/g at 0.5 A/g) compared with FeVO4 (70.4 F/g) using half‐cell measurements. Moreover, the developed symmetric supercapacitors (full cell; SSCs) using rGO‐FeVO4 composite device showed 109 F/g capacitance at 0.5 A/g current density having high energy density of 13.6 Wh/kg at the power density of 450 W/kg. The proposed rGO‐FeVO4 composite proved its multifunctional outcomes, which can open new opportunities to develop such materials for numerous future applications.

Energy recoveries and heavy metal migration behaviors of different oily sludges treated by pyrolysis versus solvent extraction

The pyrolysis and trace element mitigation characteristics are investigated by contrast to solvent extraction for four oily sludges, including storage tank bottom sediment (OS-1), scum from a wastewater separator (OS-2), white-clay-adsorbed waste oil (OS-3), and settlings from wastewater treatment (OS-4). Slow pyrolysis at 700 °C generated a single oil phase for OS-1 and separate oil and aqueous phases for OS-2, OS-3 and OS-4. Up to 73.0–88.3 % of the total energy were recovered from OS-1, OS-2 and OS-3 in the oil phase with 19.9–77.1 % oil yield; however, the oil phase from OS-4 accounted for only 13.3 % of the total energy, while the aqueous product accounted for 68.0 % of the total energy. Quantification of 16 trace elements revealed that OS-2 and OS-4 had much higher contents of Cu/Zn/As/Se/Cd/Pb and Ni/Cu/Zn/Se/Cd contents than the average crustal abundances, respectively. Correlations between evaporation and extraction rates indicated that the mitigation behaviors of trace elements were related to their occurrence modes in different oily sludges. Except for Cd, As and Se, all other trace elements were enriched in the pyrolysis residues of the oily sludges. Ni in the pyrolysis residue of OS-4 posed a moderate potential ecological risk.

Radiation therapy (RT)-free pembrolizumab plus chemotherapy (P+C) for PD-L1 TPS ≥50% locally advanced non-small cell lung cancer (LA-NSCLC): Primary analysis from multicenter single arm phase II study (Evolution trial; WJOG11819L).

LBA8050 Background: Standard of care for unresectable LA-NSCLC is chemoradiation therapy (CRT) followed by durvalumab (D). Survival curves of P monotherapy/P+C for PD-L1 TPS ≥50% stage IV NSCLC suggested possible comparable survival to CRT for stage III patients (pts). Moreover, some studies of neoadjuvant C+immunotherapy (I) for stage III pts have demonstrated high pathological complete response and major pathological response rates, implying potentially outstanding efficacy of C+I for earlier stage. We thus hypothesized P+C without RT in PD-L1 ≥50% LA-NSCLC pts provides a comparable efficacy to CRT followed by D while avoiding CRT-induced severe toxicities. Methods: This is a phase II study conducted by West Japan Oncology Group. P with platinum plus pemetrexed (PEM) (non-squamous) or P with carboplatin plus nab-paclitaxel (squamous) was administered every 3 weeks without RT. After four cycles of induction P+C, P with PEM (non-squamous) or P alone (squamous) was continued until progression or 2 years. The primary endpoint was 2 year-PFS rate (threshold/expected: 20%/45%). Results: Between May 2020 and February 2022, 21 pts were enrolled. Median age was 73 (range, 53-89). Stage IIIA/B/C included 11 (52%)/7 (33%)/3 (14%), respectively. Histologic subtypes were 14 (67%) adenocarcinoma, 5 (24%) squamous cell carcinoma, and 2 (10%) others. Median follow-up period was 29.9 (range, 0.3-44.2) months. Median number of P administrations was 30 (range, 1-35). The primary endpoint was met with 2-year PFS rate of 67% (90% CI: 46-83%). At the time of data cut-off, 13 (62%) of 21 pts were still progression-free. Median PFS and OS were not reached. Two-year OS rate was 85%. Centrally reviewed tumor response: 8 (38%) CR; 9 (43%) PR; 3 (14%) SD; and 1 (5%) NE were confirmed, resulting in overall response rate (ORR) of 81% and disease control rate of 95%. ORRs/2-year PFS rates of PD-L1 TPS 50-79% and 80-100% were 67%/56% and 92%/75%, respectively. Non-hematological AEs ≥grade 3 were observed in 11 (52%) pts, including: 2 (10%) pneumonitis; 2 (10%) pneumonia; 1 (5%) diarrhea; 1 (5%) ALT elevation; and 1 (5%) acute heart failure. There was one (5%) grade 5 AE (pneumonia). Conclusions: RT-free P+C provided long-lasting responses in approximately two-thirds of pts. Higher PD-L1 TPS cases achieved higher RR, including some CRs and higher 2-year PFS rate. To confirm our hypothesis that RT-free P+C can be a less toxic curative option in selected LA-NSCLC pts with PD-L1 TPS ≥50%, further data is warranted. Clinical trial information: NCT04153734 .

Mapping the microstructure and the mechanical performance of a combinatorial Co–Cr–Cu–Fe–Ni–Zn high-entropy alloy thin film processed by magnetron sputtering technique

The Co–Cr–Cu–Fe–Ni–Zn compositional library was studied on a combinatorial high-entropy alloy thin film processed on a silicon substrate by magnetron sputtering technique. The thickness of the coating was between 2 and 3 μm while the lateral dimension was 10 cm. The chemical composition in the layer depended on the location and for each constituent element the concentration varied between 5 and 42 at.%. The phase composition and the microstructure were mapped using synchrotron X-ray diffraction, and the crystallite size as well as the density of lattice defects (dislocations and twin faults) were determined by diffraction line profile profile analysis. In addition, selected locations were studied by transmission electron microscopy. The influence of the chemical composition on the microstructure and the mechanical behavior was revealed. The mechanical performance was characterized by nanoindentation mapping which determined the hardness and the elastic modulus versus the element concentrations. It was found that the coating contains single phase face-centered cubic (FCC) and body-centered cubic (BCC) regions as well as an intermediate two-phase area. In the whole combinatorial sample, the microstructure consisted of nanocrystalline columns growing perpendicular to the coating surface and having pores between them. Due to the porosity, the hardness and the elastic modulus were relatively low despite the nanostructure and the very high defect density. The highest hardness (3.4 GPa) and elastic modulus (119 GPa) were measured in the BCC region with the chemical composition of 10%Co–38%Cr–13%Cu–27%Fe–5%Ni–7%Zn (at.%).

The Influence of Cr Addition on the Microstructure and Mechanical Properties of Fe-25Mn-10Al-1.2C Lightweight Steel

The influence of Cr addition on the microstructure and tensile properties of Fe-25Mn-10Al-1.2C lightweight steel was investigated. The characteristics of the microstructures and deformation behavior were carried out through X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), electron backscatter diffraction (EBSD), and room temperature tensile testing. Fe-20Mn-12Al-1.5C steel without Cr exhibited a fully austenitic single phase. With the addition of Cr, the volume fraction of ferrite continuously increased. When the content of Cr exceeded 5 wt%, the precipitation of Cr7C3 carbides was observed. In the steel with 5 wt% Cr, the quantity of κ carbides remarkably decreased, indicating that the addition of 5 wt% Cr significantly inhibited the nucleation of κ-carbides. As the Cr content increases from 0 wt% to 5 wt%, the austenite grain sizes were 8.8 μm and 2.5 μm, respectively, demonstrating that Cr alloying is an effective method of grain refinement. Tensile strength increased slightly while elongation decreased with increasing Cr content. As the Cr content exceeded 5 wt%, the yield strength increased but the elongation drastically decreased. The steel with 2.5 wt% Cr achieved a synergistic improvement in strength and ductility, exhibiting the best tensile performance.

Novel zinc and gallium nanocomposites for protecting against green laser radiation

In the present communication, binary (ZnO:Ga2O3- 1:1 (ZGO), ZnO:Ga2O3- 2:1 (GaZn))/ternary (EZG (Eu2O3: ZnO: Ga2O3 (1:1:1)), MZG (MgO: ZnO: Ga2O3 (1:1:1)) NCs are synthesized by Piperbetle leaves extract as a reducing agent followed by calcination at 600 °C for 3 h. The Bragg reflections confirms the formation of single phase cubic symmetry with Fd3m space group in ZGO NCs whereas reflections related individual metal oxides are observed in the GaZn, EZG and MZG NCs. The irregular size and shaped nanoparticles are observed in all the synthesized NCs. The tuned band gap was found to be in the range of 3.08 to 3.11 eV. The optical nonlinearity of the specimens was analyzed using the open aperture Z-scan technique. The material demonstrated reverse saturable absorption attributed to a two-photon absorption (2PA) process. The non linear absorption coefficient follows the order MZG > GaZn > ZGO > EZG. However, the optical limiting threshold follows the order ZGO > GaZn > MZG > EZG NCs with increase in energy band gap. These outcomes distinctly indicate the superior potential of GaZn binary NCs for optical limiting applications. This characteristic is advantageous for shielding sensors and the human eye, safeguarding them against the detrimental effects of intense green laser radiation.

Colesevelam for Lenalidomide Associated Diarrhea in Patients with Multiple Myeloma.

Lenalidomide maintenance is associated with a significantly improved progression-free in patients with newly diagnosed multiple myeloma. Maintenance with lenalidomide is generally well tolerated; however, lenalidomide associated diarrhea is a common side effect and bile acid malabsorption has been suggested as an underlying mechanism. We conducted a single arm phase 2 trial of colesevelam, a bile acid binder, for lenalidomide-associated diarrhea in multiple myeloma. Patients were treated with colesevelam daily starting at 1250 mg (2 tablets 625 mg) for 12 weeks. The trial included 25 patients, 1 patient with grade 3 diarrhea, 14 with grade 2, and 10 with grade 1 diarrhea. All patients were on treatment with single agent lenalidomide maintenance and no patient progressed during the trial. Colesevelam treatment was highly effective for treatment of lenalidomide-associated diarrhea; 22 (88%) of the 25 patients responded where 17 patients (68%) had complete resolution of diarrhea, and 5 patients (20%) had improvement by 1 grade of diarrhea. The responses to colesevelam were seen within the first two weeks of treatment. These findings support the conclusion that lenalidomide-associated diarrhea is driven by bile acid malabsorption. Five patients reported mild gastrointestinal side effects including constipation. Importantly, the pharmacokinetics of lenalidomide were not affected by concomitant colesevelam treatment. The stool microbiome composition was not significantly different before and after colesevelam treatment. Patients reported improved diarrhea, fewer gastrointestinal symptoms, and less interference with their daily life after starting colesevelam. In summary, colesevelam was safe and highly effective for treatment of lenalidomide-associated diarrhea in multiple myeloma and does not reduce the clinical effect of lenalidomide.

Electrochemical and photoluminescence properties of Zinc vanadate nanoparticles synthesized via chemical and green mediated route

Zinc vanadate (Zn2V2O7) nanoparticles (NPs) are successfully synthesized through a solution combustion method, employing Menthaspicata leaves extract as a reducing agent (ZVP) and urea as a chemical fuel (ZVU). Subsequently, the resulting NPs undergo calcination at 600 °C for a duration of 3 h. The pure orthorhombic crystal structure with Cmce space group Bragg reflections are observed in ZVP NPs. However, along with pure orthorhombic phase, few planes corresponding to V2O5 are observed. Green extract helps to retain the single orthorhombic phase. Irregular shaped and bigger sized NPs are observed in ZVU whereas in ZVP, few hexagonal and irregular sized NPs gets decorated on the bigger sized NPs. Better crystalline structure and shape are observed in ZVP compared to ZVU. Transmission electron microscopy analysis matches well with the XRD results. The selected area electron diffraction pattern of ZVP confirms the formation of purity of the sample. The direct energy band gap estimated from the Wood and Tauc’s plot was found to be 3 and 3.04 eV for ZVU and ZVP NPs respectively. The photoluminescence experiment was carried out at 290 and 310 nm excitation wavelengths. As excitation wavelength changes, tuning of emission color is observed from blue to red region. This tuning of color is observed in CIE plot. The CCT value clearly indicates that the samples excited under 290 nm can be utilized for cool LEDs whereas, the sample excited under 310 nm can be utilized for warm LEDs. Thus, the synthesized Zinc vanadate NPs might be the promising candidates for warm/cool display technologies as a nanophosphor based on the excitation wavelength. The electrochemical studies and the capacitance process was evaluated in a 1.0 M Na2SO4 solution utilizing a specific three-electrode setup. The calculated specific capacitance values exhibited variability within the range of 56.8 to 89.7 F/g at scan rates ranging from 10 to 100 mV.

A dSPACE-based implementation of ANFIS and predictive current control for a single phase boost power factor corrector

This paper presents an innovative control scheme designed to significantly enhance the power factor of AC/DC boost rectifiers by integrating an adaptive neuro-fuzzy inference system (ANFIS) with predictive current control. The innovative control strategy addresses key challenges in power quality and energy efficiency, demonstrating exceptional performance under diverse operating conditions. Through rigorous simulation, the proposed system achieves precise input current shaping, resulting in a remarkably low total harmonic distortion (THD) of 3.5%, which is well below the IEEE-519 standard threshold of 5%. Moreover, the power factor reaches an outstanding 0.990, indicating highly efficient energy utilization and near-unity power factor operation. To validate the theoretical findings, a 500 W laboratory prototype was implemented using the dSPACE ds1104 digital controller. Steady-state analysis reveals sinusoidal input currents with minimal THD and a power factor approaching unity, thereby enhancing grid stability and energy efficiency. Transient response tests further demonstrate the system’s robustness against load and voltage fluctuations, maintaining output voltage stability within an 18 V overshoot and a 20 V undershoot during load changes, and achieving rapid response times as low as 0.2 s. Comparative evaluations against conventional methods underscore the superiority of the proposed control strategy in terms of both performance and implementation simplicity. By harnessing the strengths of ANFIS-based voltage regulation and predictive current control, this scheme offers a robust solution to power quality issues in AC/DC boost rectifiers, promising substantial energy savings and improved grid stability. The results affirm the potential of the proposed system to set new benchmarks in power factor correction technology.

Molecular ferroelectric with low-magnetic-field magnetoelectricity at room temperature

Magnetoelectric materials, which encompass coupled magnetic and electric polarizabilities within a single phase, hold great promises for magnetic controlled electronic components or electric-field controlled spintronics. However, the realization of ideal magnetoelectric materials remains tough due to the inborn competion between ferroelectricity and magnetism in both levels of symmetry and electronic structure. Herein, we introduce a methodology for constructing single phase paramagnetic ferroelectric molecule [TMCM][FeCl4], which shows low-magnetic-field magnetoelectricity at room temperature. By applying a low magnetic field (≤1 kOe), the halogen Cl‧‧‧Cl distance and the volume of [FeCl4]− anions could be manipulated. This structural change causes a characteristic magnetostriction hysteresis, resulting in a substantial deformation of ~10−4 along the a-axis under an in-plane magnetic field of 2 kOe. The magnetostrictive effect is further qualitatively simulated by density functional theory calculations. Furthermore, this mechanical deformation significantly dampens the ferroelectric polarization by directly influencing the overall dipole configuration. As a result, it induces a remarkable α31 component (~89 mV Oe−1 cm−1) of the magnetoelectric tensor. And the magnetoelectric coupling, characterized by the change of polarization, reaches ~12% under 40 kOe magnetic field. Our results exemplify a design methodology that enables the creation of room-temperature magnetoelectrics by leveraging the potent effects of magnetostriction.

Impact of Co and Cu co‐doping on the Structural, Electrical, Magnetic and Solar Light Driven Photo‐Catalytic Properties of NiFe2O4 Nano‐crystals for Crystal Violet Dye Removal

AbstractHerein, we have synthesised cobalt (Co) and copper (Cu) co‐doped Ni‐ferrite Ni1‐xCoxFe2‐yCuyO4 nanocrystals (NCs) via the facile micro‐emulsion method. The materials were analysed for various physio‐chemical characterizations to investigate the co‐doping (Co and Cu) effects on magnetic, structural, electrical, photo‐catalytic properties. The structural analysis via Fourier Transform Infrared spectroscopy (FTIR) and X‐rays diffraction (XRD) showed the successful fabrication of Co and Cu co‐doped materials with cubic spinel geometry having a single phase, the crystallite size was observed in 15 to 24 nm range. The electrical response measured using current‐voltage (I–V) analysis showed good electrical features, the electrical resistivity declined from 6.85×107 Ohm.cm for un‐doped materials to 0.04×107 Ohm.cm for co‐doped materials, which was accredited due to the synergistic effects of Co and Cu metal cations in co‐doped Ni‐based ferrite structures. Magnetic investigation using VSM analysis showed increased saturation magnetization (Ms 31.32 to 50.75 emu/g) and coercivity (218.76 to 406.82 Oe) because of the higher magnetic responses of Co2+ions in the co‐doped spinel ferrite NCs. BET surface‐area analysis showed good porosity for co‐doped materials with an increased surface area of 52 to 104 m2/g on co‐doping. The Tauc's plot described the decline of band‐gap energies value (Egs) (1.99 eV) in co‐doped (x=y=0.56) materials as compared to (2.16 eV) of the un‐doped NiFe2O4 materials, which is due to more electrical responses of Co and Cu co‐dopant cations that possess higher energy levels, which can stabilize the charge carrier‘s species. Furthermore, the photo‐degradation using solar light showed good removal of crystal violet (CV) dye, which was almost 94.14 % by co‐doped material; however, by un‐doped material, it was 38.044 %. The scavenger experiment shows that the (OH⋅) hydroxyl radicals and (e−/h+) species play a prime role in the degradation of CV dye. Recycling and recoverability tests for five cycles’ exhibited outstanding stability of the photocatalyst with only 1.7 % losses in activity. Overall, our results showed that co‐doped Ni1‐xCoxFe2‐yCuyO4 NCs materials exhibited enhancement in the magnetic, electrical, photo‐catalytic properties and a decline in band‐gap energy values as compared to un‐doped NiFe2O4, which might have potential use in magnetic and electrical devices as well as solar‐driven photo‐catalyst materials for the remediation of environmental pollution.

Fe-Doped g-C3N4/Bi2MoO6 Heterostructured Composition with Improved Visible Photocatalytic Activity for Rhodamine B Degradation.

The binary heterostructured semiconducting visible light photocatalyst of the iron-doped graphitic carbon nitride/bismuth molybdate (Fe-g-C3N4/Bi2MoO6) composite was prepared by coupling with Fe-doped g-C3N4 and Bi2MoO6 particles. In the present study, a comparison of structural characteristics, optical properties, and photocatalytic degradation efficiency and activity between Fe-doped g-C3N4 particles, Bi2MoO6 particles, and Fe-g-C3N4/Bi2MoO6 composite was investigated. The results of X-ray diffraction (XRD) examination indicate that the hydrothermal Bi2MoO6 particles have a single orthorhombic phase and Fourier transform infrared (FTIR) spectroscopy analysis confirms the formation of Fe-doped g-C3N4. The optical bandgaps of the Fe-doped g-C3N4 and Bi2MoO6 particles are 2.74 and 2.73 eV, respectively, as estimated from the Taut plots obtained from UV-Vis diffuse reflectance spectroscopy (DRS) spectra. This characteristic indicates that the two semiconductor materials are suitable for absorbing visible light. The transmission electron microscopy (TEM) micrograph reveals the formation of the heterojunction Fe-g-C3N4/Bi2MoO6 composite. The results of photocatalytic degradation revealed that the developed Fe-g-C3N4/Bi2MoO6 composite photocatalyst exhibited significantly better photodegradation performance than the other two single semiconductor photocatalysts. This property can be attributed to the heterostructured nanostructure, which could effectively prevent the recombination of photogenerated carriers (electron-hole pairs) and enhance photocatalytic activity. Furthermore, cycling test showed that the Fe-g-C3N4/Bi2MoO6 heterostructured photocatalyst exhibited good reproducibility and stability for organic dye photodegradation.

The C-BixSnSb composite toward fast-charging and long-life sodium-ion batteries

Sodium ion batteries (SIBs) fitted with high-rate and high-capacity anodes are attractive for their higher energy density and faster charging capability. However, it is still a challenge to develop high-energy SIBs with high power and long life, due to the sluggish kinetic and limited Na+ insertion in electrode materials. The inherent crystal structure and constituent element are two important factors to resolve the critical issues faced above. Taking the merits of layer-structure and middle-entropy, herein, we proposed and designed a high ion-conductive composite combing with ternary alloy and layered BixSnSb@C nanofibers, which eliminate ion migration barriers while maintaining the structural framework for superior rate property and cycle stability. Used as anode for SIBs, the multiphase BixSnSb@C with adjustable Bi content exhibits excellent Na storage capability as compared to their single phase counterpart. Specially, up to a rate of 132C (50 A g−1), the capacity is still as high as 400 mAh g−1, meanwhile, after 5000 charge and discharge cycles at a current density of 12C, the capacity still maintains 85 % of its initial capacity, which outperform the individual Bi- or SnSb-based materials. The superior electrochemical performances originate from the middle-entropy nature and layer structure of BiSnSb alloy, which can provide more channels for fast Na+ transport, and accommodate large volume changes. Besides, the activity energy and ions transport resistance of Na+ in different composites were evaluated. Furthermore, the full-cell coupled with NaNi1/3Fe1/3Mn1/3O2 as cathode was formed and a capacity retention of ∼80 % is realized in 100 cycles. The results show that the BixSnSb@C is a potential anode for fast-charging Na-ion batteries and could be used to guide the design of multi-component alloy-base anodes.

Power Components Mean Values Determination Using New Ip-Iq Method for Transients

This paper deals with the quasi-instantaneous determination (in a single-step response time) of apparent, active, and reactive (i.e., blind and distortion) power mean values including the total power factor, total harmonic distortion, and phase shift of fundamentals of a power electronic and electrical system (PEES) using the ip-iq method, which is the main contribution of the paper. The power components’ mean values are investigated during the transient and steady states. The power components’ mean values can be determined directly from phase current and voltage quantities, using an integral calculus over one period within the next calculation step and using moving average and moving rms techniques (or digital filtering). Consequently, the power factor can be evaluated with known values of a phase shift of fundamentals (using a Fourier analysis). The results of this study show how a distortion power component during transients is generated even under a harmonic supply and linear resistive–inductive load. The paper contains a theoretical base, modeling, and simulation for the three and single phases of the transients in power electronic systems. The worked-out results can be used to determine and size any PES. The presented approach brings a detailed time waveform verified by simulations in Matlab/Simulink 2022a and the Real-time HW Simulator Plecs RT Box 1.

The impact of cannabidiol (CBD) on aromatase inhibitor (AI)-associated musculoskeletal symptoms (AIMSS).

e24060 Background: Although treatment with an AI for 5-10 years decreases 10-year breast cancer (BC) mortality by about 40%, up to 25% of patients will stop treatment early because of treatment-related, intolerable joint and muscle pain and stiffness, called AIMSS. Only acupuncture, duloxetine, and exercise have been shown to reduce AIMSS. While the exact underlying mechanism is unknown, it is thought to be due in part to ongoing systemic inflammation. CBD has anti-nociceptive and anti-inflammatory properties, making it a potential treatment option for AIMSS. Methods: Women with stage 0-3 hormone receptor-positive BC experiencing AIMSS (defined as worst joint pain ≥4/10 during prior 7 days that developed or worsened since starting AI therapy) were eligible for enrollment in this single arm, single center phase 2 open label clinical trial (NCT04754399). Patients received an FDA-approved formulation of CBD (Epidiolex), titrated over 4 weeks from 25 mg BID to 100 mg BID and then continued at maximum tolerated dose for a total of 15 weeks. Patient-reported outcomes (PRO) data were collected serially, including the Brief Pain Inventory (BPI) and the PROMIS Profile 29+2 v2.1. The primary endpoint was the number of CBD-treated patients with at least a 2-point reduction (minimal clinically important difference) in worst pain from baseline to 15 weeks. Statistical analysis was completed using paired t-tests and linear mixed models. Results: Of 39 eligible patients (Table 1), 11 discontinued participation early due to patient discretion (n = 6) or adverse event (n = 5). There were no grade 3-4 toxicities. Analyzing data from all 39 patients, there was an improvement in BPI worst pain (0-10 scale) of 0.13 per week of treatment after baseline (p < 0.001), resulting in an average improvement in worst pain of 1.95 at the end of 15 weeks. Of the 28 patients who completed the study, 17 (60.7%) reported a ≥2-point improvement in BPI worst pain between baseline and week 15. There was a significant improvement in PROMIS T score at week 15 in both physical function (2.34, p = 0.01) and ability to participate in social roles and activities (2.71, p = 0.02). Conclusions: Treatment with CBD was associated with an improvement in joint pain for a subset of patients. Additional analyses are ongoing to further investigate the impact of CBD on AIMSS and to explore which patients are most likely to benefit from treatment with CBD. Clinical trial information: NCT04754399 . [Table: see text]

A multi-centre, single arm, phase 2 trial of pembrolizumab in treatment-naïve patients with carcinoma of unknown primary site.

2659 Background: Cancer of unknown primary (CUP) represents a heterogeneous group of cancers that present with metastatic epithelial disease with no identifiable primary lesion at the time of diagnosis. Patients with poor prognostic features have limited effective systemic therapy options. Researchers hypothesize that these primary lesions are occult, in part, due to anti-cancer immune surveillance. We hypothesize, pembrolizumab will have activity in this setting. Methods: This single arm phase 2 study evaluated the use of pembrolizumab in treatment naïve patients with poor prognosis CUP. Patients ≥18 years of age with ECOG PS 0-1 and histologically proven, measurable metastatic carcinoma with no primary site identified were eligible. Pembrolizumab was administered at 200 mg intravenously every 3-weeks for up to 24 months. The primary endpoint was safety and objective response rate (ORR) per RECIST 1.1. Secondary objectives included progression free survival (PFS) and overall survival (OS). The study used a Simon’s two stage design based on a one-sided test with a type 1 error rate of 0.1, null hypothesis for ORR ≤ 20% yielding a power of 0.8 with an alternate hypothesis of ≥40%. The null hypothesis will be rejected if 8 or more responses are observed in 25 patients. Mismatch repair (MMR) and microsatellite instability (MSI) testing was not mandatory for patients. Results: There were 27 evaluable and 6 unevaluable (no response assessment, included in adverse event analysis) patients. The median age was 64 (range 21-80) and the majority were male (57.6%) and ECOG 1 (84.8%). Four patients experienced grade 3 treatment related adverse events (pain, anorexia, fatigue, confusion, and anemia). There were no treatment related deaths or new signals of toxicity. Of the evaluable patients, the ORR was 18.5% (4 partial responses and 1 complete response), disease control rate was 51.9% (9 stable disease) and thus the null hypothesis could not be rejected. For evaluable patients, the median PFS and OS were 2.56 (95% CI 2.10 – 7.46) and 9.79 (95% CI 3.84 – 16.03) months respectively. The one patient who developed a CR had MMR deficiency and has completed 2 years of therapy. Of the 4 patients with a partial response, one had an MMR proficient tumour, while the remaining 3 had unknown MMR status. Conclusions: Although not meeting the primary endpoint, pembrolizumab has some activity in CUP patients. Patients with CUP should be screened for MMR or MSI. Future studies should evaluate combination therapies with the addition of pembrolizumab. Clinical trial information: NCT03391973 .