Single Configuration Research Articles

Effect of module configurations on the performance of parallel-connected lithium-ion battery modules

To meet the power and energy of battery storage systems, lithium-ion batteries have to be connected in parallel to form various battery modules. However, different single module collector configurations (SCCs) and unavoidable interconnect resistances lead to inhomogeneous currents and state-of-charge (SoC) within the module, thereby significantly reducing the module lifetime and safety. Therefore, the correlation of SCCs to module inhomogeneous currents and SoC are worth investigating. Based on mathematical permutations and combinations calculations, all SCCs are firstly defined and obtained in this paper. Then, two parallel modules are developed in Matlab/Simscape based on fresh cell and degradation cell separately, which are used to quantify the influence of all SCCs. Furthermore, multiple module collector configurations (MCCs) and Urban Dynamometer Driving Schedule (UDDS) working condition are considered in the analysis. Results indicate that both module collectors connected to same edge cell of module cause the most inhomogeneity. The maximum SoC difference under the UDDS is only 46 % of the 0.5C. Moreover, MCCs can reduce inhomogeneous currents and SoC within the parallel module, while not all MCCs perform better homogeneous performance than SCCs. Finally, the effect of changes in SCCs on degradation module inhomogeneous currents and SoC is verified as same as for fresh cells parallel module. Based on the above results, the optimal single module collector configuration of the N cells parallel module is obtained through mathematical analysis, which can greatly improve the currents and SoC homogeneity of the module.

Optimized design of a fault-tolerant 12-slot/10-pole six-phase surface permanent magnet motor with asymmetrical winding configuration for electric vehicles

This paper presents a comprehensive methodology for optimizing the design of a 12-slot/10-pole permanent magnet (PM) motor with a six-phase winding configuration tailored for electric vehicles (EVs). The design aims to enhance motor performance under both healthy and fault conditions. While the single neutral configuration offers superior torque during faults, it also introduces zero sequence currents and additional space harmonics, which can lead to increased torque ripple that is difficult to control. This study addresses these challenges through innovative machine design optimization. The optimization process begins with sizing equations to establish an initial design. K-means clustering techniques are then employed to identify distinct loading points that accurately represent the full EV driving cycle, effectively minimizing computational power requirements. Following this, the Full Range Minimum Loss (FRML) strategy is applied to determine optimal current profiles across these loading points, significantly reducing copper losses. Finally, a multi-objective optimization approach is utilized to minimize torque ripple, enhance average torque, and optimize machine losses. The results demonstrate substantial improvements in torque and reduced ripple, validated through experiments conducted with a 2 kW lab-scale motor. This integrated approach not only ensures a robust and efficient motor design but also enhances fault tolerance, making it well-suited for advanced EV applications.

Enhancing timing performance of heterostructures with double-sided readout

Objective.Heterostructured scintillators offer a promising solution to balance the sensitivity and timing in TOF-PET detectors. These scintillators utilize alternating layers of materials with complementary properties to optimize performance. However, the layering compromises time resolution due to light transport issues. This study explores double-sided readout-enabling improved light collection and Depth-of-Interaction (DOI) information retrieval-to mitigate this effect and enhance the timing capabilities of heterostructures.Approach.The time resolution and DOI performances of 3 × 3 × 20 mm3BGO&EJ232 heterostructures were assessed in a single and double-sided readout (SSR and DSR, respectively) configuration using high-frequency electronics.Main results.Selective analysis of photopeak events yielded a DOI resolution of 6.4 ± 0.04 mm. Notably, the Coincidence Time Resolution (CTR) improved from 262 ± 8 ps (SSR) to 174 ± 6 ps (DSR) when measured in coincidence with a fast reference detector. Additionally, symmetrical configuration of two identical heterostructures in coincidence was tested, yielding in DSR a CTR of 254 ± 8 ps for all photopeak events and 107 ± 5 ps for the fastest events.Significance.By using high-frequency double-sided readout, we could measure DOI resolution and improve the time resolution of heterostructures of up to 40%. The DOI information resulted intrinsically captured in the average between the timestamps of the two SiPMs, without requiring any further correction.

Response Matching for Generating Materials and Molecules.

Diffusion models have recently emerged as powerful tools for the generation of new molecular and material structures. The key insight is that the noise in these models is related to the response of the atoms to displacement, and the denoising step is thus analogous to the geometry relaxation of atomistic systems starting from a random structure. Building on this, we present a generative method called Response Matching (RM), which leverages the fact that each stable material or molecule exists at the minimum of its potential energy surface. Any perturbation induces a response in energy and stress, driving the structure back to equilibrium. Matching this response is closely related to score matching in diffusion models. Another important aspect of state-of-the-art diffusion models is the incorporation of physical symmetries such as translation, rotation, and periodicity. RM employs a machine learning interatomic potential and random structure search as the denoising model, inherently respecting these symmetries and exploiting the locality of atomic interactions. RM handles both molecules and bulk materials under the same framework. Its efficiency and generalization are demonstrated on three systems: a small organic molecular data set, stable crystals from the Materials Project, and one-shot learning on a single diamond configuration.

How Shell Add-On Products Influence Varsity Football Helmet Performance?

PurposeThe study purpose was to investigate the laboratory-based performance of three commercially available shell add-on products under varsity-level impact conditions.MethodsPendulum impact tests were conducted at multiple locations (front, front boss, rear, side) and speeds (3.1, 4.9, 6.4 m/s) using two helmet models. Tests were performed with a single add-on configuration for baseline comparisons and a double add-on configuration to simulate collisions with both players wearing shell add-ons. A linear mixed-effect model was used to evaluate peak linear acceleration (PLA), peak rotational acceleration (PRA), and concussion risk, which was calculated from a bivariate injury risk function, based on shell add-on and test configuration.ResultsAll shell add-ons decreased peak head kinematics and injury risk compared to controls, with the Guardian NXT producing the largest reductions (PLA: 7.9%, PRA: 14.1%, Risk: 34.1%) compared to the SAFR Helmet Cover (PLA: 4.5%, PRA: 9.3%, Risk: 24.7%) and Guardian XT (PLA: 3.2%, PRA: 5.0%, Risk: 15.5%). The same trend was observed in the double add-on test configuration. However, the Guardian NXT (PLA: 17.1%; PRA: 11.5%; Risk: 62.8%) and SAFR Helmet Cover (PLA: 12.2%; PRA: 9.1%; Risk: 52.2%) produced larger reductions in peak head kinematics and injury risk than the Guardian XT (PLA: 5.7%, PRA: 2.2%, Risk: 21.8%).ConclusionIn laboratory-based assessments that simulated varsity-level impact conditions, the Guardian NXT was associated with larger reductions in PLA, PRA, and injury risk compared to the SAFR Helmet Cover and Guardian XT. Although shell add-ons can enhance head protection, helmet model selection should be prioritized.

Electromagnetic Absorber Covering the P-band and THz band Based on Ferrite Materials with Multilayer Microstructural Units

In this work a novel absorber that can operate simultaneously at the previous (P) and terahertz (THz) frequencies is proposed. This innovation features a single configuration composed of NiCuZnBi ferrite with periodic microstructure on the surface. In P band, the absorber achieves an absorption efficiency of more than 90 % (with a reflection loss of less than −10 dB) across the frequency range of 429.5 to 1000 MHz. This extremely low frequency absorption is solely attributed to the inherent magnetic loss of NiCuZnBi ferrite and is independent of the surface structure of the absorber. In the THz band, with this same absorber, a single layer of NiCuZnBi microstructure unit can achieve broad absorption range from 351.8 to 1200 GHz due to local energy loss caused by diffraction effects. More importantly, we have revealed the principle that increasing the number of NiCuZnBi microstructure unit layers is beneficial for broadening the THz absorption bandwidth. By designing stacked multi-layer structural units, we increased the absorption bandwidth of the device from 848.2 GHz for single-layer structures to 932.8 GHz for two-layer structures and 969.1 GHz for three-layer structures, respectively. The cross-band device design method proposed here makes it possible to develop electromagnetic absorbers that cover the P-band, THz band, and even more other frequency bands, thereby meeting the requirements of future applications such as multi-spectrum electromagnetic stealth and 6G communication.

Comparative Study of Single and Coaxial Electrospun Antimicrobial Cross-Linked Scaffolds Enriched with Aloe Vera: Characterization, Antimicrobial Activity, Drug Delivery, Cytotoxicity, and Cell Proliferation on Adipose Stem Cells and Human Skin Fibroblast.

The preparation of materials with application in the biomedical field needs to attend some characteristics such as biocompatibility, nontoxicity, adequate mechanical properties, and the ability to mimic the extracellular matrix. Scaffolds for use in cell culture were prepared based on gelatin, polylactic acid (PLA), aloe vera mucilage, and tetracycline. Fibers were prepared in single and coaxial configuration and then cross-linked with glutaraldehyde saturated vapor. The fibers were obtained with cylindric morphology and changed to ribbon morphology and porous membranes, similarly to the extracellular matrix, when cross-linked. Membranes prepared by coaxial electrospinning showed core-shell structures when observed by transversal images, which is beneficial for controlled drug release. Characterization techniques such as scanning electron microscopy, thermogravimetric analysis, and Fourier transform infrared spectroscopy demonstrated the cross-linking due to the increase in diameter, formation of imine groups, and improvement of thermal stability. Antibiotic release tests showed that the prevalent release mechanism is diffusion and can be controlled considering the encapsulation effect, when fibers are prepared with a coaxial configuration, increasing the drug release time, making it a suitable material for controlled release. The biological evaluation of the scaffolds was carried out in two cell lines: mammalian adipose stem cells (ASCs), used as a primary cell culture, and Detroit 548 human skin fibroblasts as a dermal cell model. Aloe vera enriched scaffolds showed better activity in contact with both cell lines, exhibiting cell viability values greater than 90% and favorable results in live-dead assays when no damaged cells were observed. Cell proliferation was evaluated using Detroit 548 human skin fibroblast on gelatin-based scaffolds by the staining of the adhered cells; the images showed good confluence and morphology of the cells on the aloe vera and antibiotic loaded membranes for both of the studied configurations. Antibiotic loaded membranes presented antimicrobial activity against S. aureus, and this behavior increased when aloe vera is included. According to the results, the scaffolds prepared on single configuration enriched with aloe vera and tetracycline could be used in dermal tissue engineering as burn dressings, diabetic foot apposite, and skin substitutes, and the scaffolds prepared with a coaxial configuration are recommended for controlled release systems of antibiotics as treatments for chronic wounds such as diabetic foot and burn healing.

Local volume concentration, packing domains, and scaling properties of chromatin.

We propose the Self Returning Excluded Volume (SR-EV) model for the structure of chromatin based on stochastic rules and physical interactions. The SR-EV rules of return generate conformationally defined domains observed by single-cell imaging techniques. From nucleosome to chromosome scales, the model captures the overall chromatin organization as a corrugated system, with dense and dilute regions alternating in a manner that resembles the mixing of two disordered bi-continuous phases. This particular organizational topology is a consequence of the multiplicity of interactions and processes occurring in the nuclei, and mimicked by the proposed return rules. Single configuration properties and ensemble averages show a robust agreement between theoretical and experimental results including chromatin volume concentration, contact probability, packing domain identification and size characterization, and packing scaling behavior. Model and experimental results suggest that there is an inherent chromatin organization regardless of the cell character and resistant to an external forcing such as RAD21 degradation.

Bonding and Interactions in UO22+ for Ground and Core Excited States: Extracting Chemistry from Molecular Orbital Calculations.

Theoretical analyses of actinyls are necessary in order to understand and correctly interpret the chemical and physical properties of these molecules. Here, wave functions of Uranyl, UO22+, are considered for the ground state and for the core excited states where an electron is promoted from the U 3d5/2 shell into a low-lying unoccupied orbital that is U 5f antibonding with the ligand, O, orbitals. A focus is on the application of novel theoretical methods to the analysis of these wave functions so that measurements, especially with X-ray absorption, can be related to the UO22+ chemical bonding. The bond covalency is examined with these theoretical methods. The study includes how the covalent character is different for the ground and excited configurations and how this character changes as the U-O distance is changed. Furthermore, analyses are mode of how many-body effects may modify excitation energies and X-ray adsorption intensities. This includes determining the extent to which a single configuration provides a satisfactory model for the UO22+ wave functions. Two distinct types of many-body effects are considered. One involves the angular momentum coupling of the open shell electrons in the excited states to yield correct multiplets. The second adds excitations from shells that are bonding into the antibonding open shell space. These excitations are essential to properly describe the X-ray adsorption. While these many-body effects must be taken into account, their importance and their role can be explained and understood using orbitals and orbital occupations.

A study into the correlation between single array-hull configurations and wave spectrum for floating solar photovoltaic systems

Floating photovoltaic (FPV) systems offer a viable renewable energy solution due to easy installation and cost-effectiveness compared to other renewable energy generation methods. On the other hand, land-based solar photovoltaics face challenges such as space scarcity and environmental impacts. Shifting to nearshore locations unlocks vast ocean space potential, though waves expose significant challenges to FPV systems. Several novel FPV system designs are proposed, inspired by high-speed vessel multihulls, including catamaran, trimaran, quadrimaran, and pentamaran configurations, as floating supports for solar panels. Simulations were conducted to determine Response Amplitude Operators (RAOs) under various irregular wave spectrum conditions in a free-floating initial state. The FPV motion problem was solved using linear potential-flow theory with the Boundary Element Method (BEM) with Green-Function approach. Superposition of wave spectral energy and motion RAOs was used to obtain spectral structural responses. Motion in heave, roll, and pitch modes was evaluated across wave spectrum types. Results show that adding hulls reduces the significant amplitude response in all motion modes. In summary, valuable insights into floater designs and the hydrodynamic evaluation of FPV systems are presented.

Characterization of highly radiating nitrogen-seeded H-mode plasmas in unfavorable BT at ASDEX Upgrade

Abstract The highly radiating nitrogen-seeded H-mode plasmas in unfavorable BT has been characterized in the ASDEX Upgrade tokamak (AUG). Three levels of nitrogen puffing rates have been injected into a fully detached H-mode plasma, which is run in lower single null configuration with the ion B × ∇ B drift away from the X-point. A cold ( ∼ 1 − 2 eV) highly radiating ( ∼ 13.0 MW m − 3 ) region forms close to the X-point immediately after nitrogen seeding, as evidenced by measurements of the divertor Thomson scattering (DTS) and the two-dimensional bolometry reconstructions. In addition, the radiator moves further upwards above the X-point along the separatrix at the high-field side (HFS) with increasing nitrogen puffing rates, as evidenced by the Absolute eXtended UltraViolet (AXUV) measurements. The formation of the highly radiating regime is closely correlated to the modifications of the divertor plasma conditions. Along the line of sight of the DTS measurement, the electron temperature reduces down to a few eV, which initials near the X-point and further extends to the HFS scrape-off layer (SOL) simultaneously with the upward movement of the radiator, however, the electron temperature sustains ( ∼ 30 − 50 eV) at the low-field side (LFS) SOL with slightly decreased electron density. The highly radiating regime shows LFS/HFS divertor asymmetry, in contrast to that for H-mode plasmas in favorable BT , suggesting that the drifts play an important role for the formation of the highly radiating X-point regime at AUG. The neutral particle flux increases significantly (factor of ∼ 2 ) in the private flux region, while it increases slightly ( < 20 % ) in the main chamber, thus suggesting an enhanced sub-divertor neutral compression with the formation of the highly radiating regime. Furthermore, a degradation of the pedestal electron density was observed with an enhancement of the electron temperature further inside the pedestal, and complete divertor detachment was achieved by nitrogen seeding with sustained plasma confinement. Finally, particle sources and flow patterns of deuterium and nitrogen ions have been analyzed by SOLPS-ITER modelling, confirming that the E × B drift plays an important role for the formation of the highly radiating regime in unfavorable BT at AUG.

Coherent spin wave excitation with radio-frequency spin–orbit torque

Spin waves, collective perturbations of magnetic moments, are both fundamental probes for magnetic physics and promising candidates for energy-efficient signal processing and computation. Traditionally, coherent propagating spin waves have been generated by radio frequency (RF) inductive Oersted fields from current-carrying electrodes. An alternative mechanism, spin–orbit torque (SOT), offers more localized excitation through interfacial spin accumulation but has been mostly limited to DC to kHz frequencies. SOT driven by RF currents, with potentially enhanced pumping efficiency and unique spin dynamics, remains largely unexplored, especially in magnetic insulators. Here, we conduct a comprehensive theoretical and computational investigation into the generation of coherent spin waves via RF-SOT in the prototypical yttrium iron garnet. We characterize the excitation of forward volume, backward volume, and surface modes in both linear and nonlinear regimes, employing single and interdigitated electrode configurations. We reveal and explain several unique and surprising features of RF-SOT compared to inductive excitation, including higher efficiency, distinct mode selectivity, and directional symmetry, a ∼3π/4 phase offset, reduced anharmonic distortion in the nonlinear regime, and the absence of second harmonic generation. These insights position RF-SOT as a promising new mechanism for future magnonic and spintronic applications.

PSIX-3 Dental stick extrusion utilizing spray dried plasma

Abstract Dental stick extrusion utilizes various ingredients to form the ideal texture and quality product. Alternative ingredients to enhance or impact texture, palatability and/or plaque removal can be useful to improve dental stick manufacturing. Spray dried plasma (SDP) is a consistent high protein ingredient commonly utilized in pet food for functional texture properties, enhancing palatability, and supporting overall health. Thus, the study objective was to evaluate how SDP inclusion with other ingredients impacts texture of extruded dental formulas. Three formulas were developed utilizing SDP to replace wheat starch (WS) or Arabic gum in the control formula. The formulas were: Control: WS and gum; SDP1: SDP and WS replacing gum; and SDP2: SDP replacing WS and gum. Dental sticks were made at the Extru-Tech technology testing center using a 525 single screw extruder with the product densification unit (PDU) removed and replaced with a mid-barrel valve and 3 cooling heads to cause densification. The sticks were manufactured as solid square sticks. Generally, a single screw with a PDU, or a traditional parallel-shaft twin screw is used to manufacture dental sticks. However, the equipment alterations used worked like a single screw with a PDU; thus, it would be expected that the results would translate to a traditional single screw configuration. Glycerin at 12% (% to dry feed rate) and chicken fat were added to the pre-conditioner at set rates to optimize expansion and product quality. Processing conditions were monitored and adjusted on the various formulations during production to optimize extrusion. Texture was measured on a TA.XT Plus utilizing an adjustable bridge with a rounded-end knife probe for a 3-point bend. Dental sticks of 8 cm in length were placed over the two bridge spans spaced 5 cm apart to measure maximum force (hardness) and work to peak force (work to break) to determine texture parameters. Ten dental sticks per treatment were analyzed. All formulas utilizing SDP were successful in producing dental sticks. No differences (P > 0.05) were noted in force with SDP formulas compared with control. Work to peak was greater (P < 0.05) in SDP formulas compared with control formula. Formulation matrix impacts results. In the current formulas, both Arabic gum and WS were altered in the formulas and depending on amount of SDP used similar texture was noted. In conclusion, SDP can be incorporated into dental stick formulas and utilized as a processing aide. Overall, depending on target hardness and ingredient matrix, SDP can be an alternative to various ingredients to maintain or improve product quality.

Octupole correlations in stable nucleus 153Eu within reflection-asymmetric particle rotor model

Abstract The observed low-lying K=5/2± positive- and negative-parity bands in the stable nucleus 153Eu are investigated by the reflection-asymmetric triaxial particle rotor model. The experimental energy spectra, the energy staggering parameters, as well as the intraband E2 and M1 transition probabilities are well reproduced. It is found that the calculated interband B(E1) values depend sensitively on the octupole deformation parameter β30, although the energy spectra and intraband E2 and M1 transitions can be reproduced without the octupole degree of freedom. The observed enhanced E1 transition probabilities can be reproduced with β30=0.05. The detailed analysis of the intrinsic wave functions shows these nearly degenerate positive- and negative-parity bands are built on two individual proton configurations, i.e., dominated by πg9/2[Ω=5/2] and πh11/2[Ω=5/2], respectively, which differs from the parity doublet bands built on a single parity-mixed configuration.

Self-assembly of single species polygons with patchy models in 2D

The goal of this work is to produce single species of polygons in two dimensions using the self-assembly of a simple patchy molecular model. A molecule is defined as a central soft repulsive Weeks Chandler and Anderson (WCA) atom that is decorated with two or four patches, which describe the two models studied in this work. Model I has two Lennard–Jones (LJ) patches inside of its central atom separated by an angle θ that intends to define the number of polygon sides. The attractive potential of these patches, interacting as pairs, is used to bond molecules together to form polygons. Model II, having two additional soft repulsive WCA patches, tangent on the outside, produces single polygon species configurations. An example of Model I with an angle θ = 120 ∘ , forming a mixture of polygons, is included. Model II produces single polygon species with 3-8 sides, depending on the angle θ between the attractive patches. Molecular dynamics simulations in the canonical ensemble are used to calculate thermodynamic properties such as internal energy, percentage of polygons, pressure and contour plots for the percentage of polygons following isochoric processes. Different starting configurations are used to verify the consistency of the equilibrium results.

An improved moment distribution method for the analysis of concrete frames

The moment distribution method is considered one of the easiest and most reliable analysis methods. However, little attention has been given to modelling the stiffness of each member separately, as currently only one factor is being used to model all structural members without taking into account the loading conditions and curvature of the member. This can significantly influence the results when modelling columns, since unlike beams, which are usually bent in a single curvature configuration, columns can be bent in either a single or double curvature configuration. This paper presents a new set of stiffness factors to model each structural member separately depending on its boundary conditions and curvature. To validate this modification, an example concrete frame was modelled and analysed using the structural analysis software ETABS, and then the results were compared with that obtained from the standard moment distribution method and the modified moment distribution method. The results have revealed a significant enhancement in the accuracy of the obtained results when using the modified moment distribution method compared with the original moment distribution method, especially the values of the columns’ bending moments.

Numerical analysis of stacked HTS tapes in rotating magnetic fields using H and T-A formulations

Superconducting windings in rotating electrical machines and multi-phase transformers are subject to rotating magnetic fields. Most existing studies on the electromagnetic characteristics of stacked high-temperature superconducting (HTS) tapes focus on the influence of vertical magnetic field (VMF) and the transport current. The numerical study on characteristics of HTS stacked tapes in rotating magnetic fields (RMFs) has received less research attention. This paper presents two-dimensional models of stacked HTS tapes in RMF based on H and T-A formulations. AC losses obtained by the two formulations agree well in a single tape configuration but significantly differ in a stack configuration. The discrepancy increases as the number of stack layers and the stack interval increase. Under the same magnetic field amplitude, the RMF penetration depth in stacked tapes is higher than those of VMF and parallel magnetic field (PMF), and the parallel component of RMF causes higher AC loss in the end tapes of a stack. While the applied current increases the overall AC loss, it can significantly decrease the AC loss of the end tape. It is found that reducing the stack interval and replacing end tapes with tapes of higher critical current can significantly reduce the overall AC loss of stacked tapes in an RMF. These results are crucial for modeling superconducting machines and offer valuable insights into characterizing superconducting tapes in RMFs using numerical methods.

Investigating the impact of battery arrangements on thermal management performance of lithium-ion battery pack design

The working temperature is one of the key factors affecting the efficiency and safety performance of automotive power batteries. Current battery pack design primarily focuses on single layout configurations, overlooking the potential impact of mixed arrangements on thermal management performance. This study presents a module-based optimization methodology for comprehensive concept design of Lithium-ion (Li-ion) battery pack. Firstly, the arrangement modules is optimized and performed using particle swarm optimization algorithms considering various arrangement layout (i.e. rectangular, diamond, and staggered arrangements) by taking the intercell spacing and maximum temperature of the modules as design objectives. Secondly, the battery pack configuration design is performed employing a neural network model reflect diverse battery module configurations within the pack, exploring their impact on thermal management performance. The hybrid battery arrangement effectively improves thermal management, and the module spacing helps to enhance heat dissipation. The staggered arrangement has a greater impact on the heat dissipation performance of the battery pack, but the spacing between different modules varies with the position of the modules. When all configuration schemes are staggered modules, the optimal range of the spacing between modules is between 6 and 7 mm. However, the study observes a non-linear relationship between module spacing and the maximum temperature difference within the battery pack. While increasing module spacing initially decreases temperature differences, it eventually reverses, suggesting that spacing alone may not consistently enhance thermal management. Validation with a lithium-ion battery pack case study demonstrates the method’s effectiveness, providing valuable knowledge for future cell and pack designs that employ different battery cell arrangements and diverse cooling strategies.

Soliton-based modeling of nano-ionic currents in transmission line

Many nonlinear evolution equations, such as the nano-ionic currents (NIC) equation, are used extensively in many scientific and technological domains particularly in nanoelectronics and bioelectronics. The mathematical modeling of NIC phenomena is vital for understanding their behavior and optimizing device performance. Our research leverages an array of mathematical methods, including multi-wave analysis, periodic wave solutions, lump soliton dynamics, breather wave phenomena, homoclinic breathers, M-shaped waveforms, and rogue wave analysis. Additionally, our investigation encompasses the exploration of single kink and double kink configurations, interactions between periodic and kink waves, interaction between M shaped with kink and rogue, interaction between M shaped with one kink, interaction between M shaped with kink and periodic, interaction between M shaped with two kinks as well as periodic wave interactions with lump waves. To further emphasize the structure of solutions derived from particular parameter choices, we include three-dimensional, two-dimensional, streamplot, and contour graphs.

Evaluation of Modeled Diurnal Warming Estimates for Application to Producing Sea Surface Temperature Analyses

AbstractAccurate knowledge of the amount of diurnal warming present in sea surface temperature (SST) observations at different times and effective depths is important for multiple applications including the production of blended SST analyses. This work explores the ability of a modified Kantha‐Clayson‐type one‐dimensional mixed layer ocean model with wave effects to accurately simulate the observed diurnal warming amplitude over a global grid when forced with coarse resolution numerical weather prediction (NWP) outputs. The sensitivity of the modeled diurnal amplitudes to multiple adjustable parameters and model configurations is evaluated to determine whether a preferred configuration can be identified that yields reliable predictions. The accuracy of the predictions is determined through comparison against estimates from operational SST retrievals from geostationary satellites. The results show that a single configuration can yield predictions that reproduce the observed range of diurnal warming amplitudes across a range of seasons and locations and an accurate occurrence frequency of the largest amplitude events. Simulated amplitudes fall along the one‐to‐one line with observations but with significant scatter due to factors including positioning of the NWP fluxes. The identified configuration is also shown to favorably reproduce diurnal warming observations from multiple research cruises. Overall uncertainty of the simulated diurnal warming amplitude across the different tests ranges between 0.4 K for all observations to ∼1 K for the largest warming events. While the focus is not on model comparisons, the results show improved performance relative to other models. Use of the model appears warranted but the associated uncertainty must be considered.