Simultaneous Improvement Of Strength Research Articles

Deformation, fracture, and fatigue crack growth behavior in TiB-reinforced near-α Ti matrix composites fabricated using powder metallurgy technique

Titanium matrix composites with TA15 alloy as the matrix and TiB (ranging from 0 to 4 vol%) as reinforcement were produced via powder metallurgy-based hot press sintering, employing AlB2 precursor. The addition of TiB to TA15 led to a substantial reduction in the colony and prior β grain sizes, and an increase in the lath thickness in the composites. Plastic deformation due to planar slip, which traverses across the α/β-ligament phase boundaries within each colony, may cause TiB particles located on colony boundaries to break, potentially more so than those within the colony. The composite containing 1 vol% TiB exhibited simultaneous improvements in strength, ductility, and strain hardening rate, attributed to colony refinement and possibly a sizable amount of intra-boundary TiB. Further increase in the TiB content led to significant drops in ductility, which was further exacerbated by the precipitation of α2-Ti3Al phase. A substantial decrease in the mode I fracture toughness, attributed to reduced colony size and diminished crack deflection, was noted in the composite with 1 vol% TiB. The colony size refinement also contributed to a reduction in the threshold stress intensity factor range, ΔK0, for the fatigue crack growth, owing to the decreased tortuosity of the fatigue crack front. This study elucidates the intricate relationship between TiB location, microstructure, and mechanical properties, providing insights for the design of TiB-reinforced titanium alloys with both α and β phases.

Effects of residual elements on the microstructure and mechanical properties of a Q&P steel

Producing steel requires large amounts of energy to convert iron ores into steel, which often comes from fossil fuels, leading to carbon emissions and other pollutants. Increasing scrap usage emerges as one of the most effective strategies for addressing these issues. However, typical residual elements (Cu, As, Sn, Sb, Bi, etc.) inherited from scrap could significantly influence the mechanical properties of steel. In this work, we investigate the effects of residual elements on the microstructure evolution and mechanical properties of a quenching and partitioning (Q&P) steel by comparing a commercial QP1180 steel (referred to as QP) to the one containing typical residual elements (Cu+As+Sn+Sb+Bi<0.3wt%) (referred to as QP-R). The results demonstrate that in comparison with the QP steel, the residual elements significantly refine the prior austenite grain (9.7μm vs. 14.6μm) due to their strong solute drag effect, leading to a higher volume fraction (13.0% vs. 11.8%), a smaller size (473 nm vs. 790 nm) and a higher average carbon content (1.26 wt% vs. 0.99 wt%) of retained austenite in the QP-R steel. As a result, the QP-R steel exhibits a sustained transformation-induced plasticity (TRIP) effect, leading to an enhanced strain hardening effect and a simultaneous improvement of strength and ductility. Grain boundary segregation of residual elements was not observed at prior austenite grain boundaries in the QP-R steel, primarily due to continuous interface migration during austenitization. This study demonstrates that the residual elements with concentrations comparable to that in scrap result in significant microstructural refinement, causing retained austenite with relatively higher stability and thus offering promising mechanical properties and potential applications.

Integrated manufacturing of powder metallurgy preparation-thixoforming for Al0.8Co0.5Cr1.5CuFeNi HEA: Excellent formability and enhancement by in-situ generated Al2O3 in liquid phase

Thixoforming displays wild application prospects in manufacturing Cu containing high entropy alloy (HEA) product. In current work, we proposed a novel manufacturing strategy on powder metallurgy preparation-thixoforming for Cu containing HEAs, integrating material preparation, shaping and strengthening objectives. During thixoforming, oxide in-situ generation in liquid phase was utilized to reinforce soft phase, achieving the strengthening of component. Based on this strategy, manufacturing of disc-shaped component for a model Al0.8Co0.5Cr1.5CuFeNi HEA was studied. Compared to 1175 °C thixoforming, room-temperature strength experiences a breakthrough increase at 1200 °C and 1225 °C, accompanied by an increase in yield strength of 323.8 MPa and 314.8 MPa, an increase in ultimate strength of 374.2 MPa and 470.0 MPa, meanwhile, fracture strain improves, which is caused by a considerable amount of in-suit generated Al2O3. Homogeneous and almost defect free microstructure obtained under higher temperature conditions ensures uniformity of mechanical properties for the whole component. As thixoforming temperature increases, preferred orientation of grain fiber shape becomes random, plastic deformation of solid grain (PDS) turns to flow of liquid incorporating solid particles (FLS), sliding between solid particles (SS) during material flow filling, which effectively reduces material damage risk caused by strain localization. In-situ generated Al2O3 in liquid phase helps to hinder crack propagation and blunt crack tip in Cu rich soft phase. Al2O3 only strengthens soft phase, relieving mismatch of strength-plasticity properties between soft and hard phase, accordingly, failure of soft phase is delayed and simultaneous improvement of strength and plasticity is achieved.

Strong and stable ultrafine-grained Al-Mg alloys via polymer-derived in situ nanoparticles

Ultrafine-grained Al-Mg alloys provide immense promise as lightweight metallic materials for load-bearing applications, contributing significantly to energy efficiency and CO2 emission reduction. However, for prevalent bulk ultrafine-grained Al-Mg alloys fabricated by a combined mechanical alloying and thermomechanical consolidation, the presence of remaining polymers, which are used as a process control agent during milling, jeopardizes the mechanical performance of the consolidated materials and thus significantly limit their broad applications. An ideal solution to overcome this critical issue is to turn these polymers into useful nanoparticles, enabling simultaneous improvements in strength and grain size stability. In this study, we present an approach to currently achieve strength enhancement and grain size control by incorporating polymer-derived in situ nanoparticles. Through a combined process involving polymer-assisted mechanical alloying, extrusion at the eutectic temperature, and annealing-driven solid-state phase transformation, we achieved a strong and stable ultrafine-grained Al-Mg alloy. After post-heat treatment at 440 °C (i.e. 0.76 Tm; Tm is the absolute melting temperature of pure Al) for 24 h, the compressive yield strength exhibited minimal reduction from ∼1.3 GPa for the as-extruded alloy to ∼1 GPa for the as-annealed alloy. Similarly, the average grain size only experienced a slight increase, from 106 to 145 nm after post-annealing. These findings offer practical insights into the design of mechanically robust and thermodynamically stable ultrafine-grained metallic materials via a new strategy of polymer-derived in situ nanoparticles.

Achieving simultaneous improvement in strength and ductility in Al–Si–Mg–Ce alloy through synergistic morphology modification of eutectic (Si) and Al2Si2Ce phases by Sr addition

In this paper, it was found for the first time that with Sr addition in Al–Si–Mg–Ce alloy, the morphology of eutectic (Si) can be modified from branch to fine fibrous, while the bulk-like Al2Si2Ce phase may replace the elongated needle-like one. Moreover, Mg was observed to segregate along the (Al)/Al2Si2Ce interface and Sr was found to concentrate in the interior of Al2Si2Ce phase. Such heterostructured Sr–Al2Si2Ce was also supported by first-principles calculations. The synergistic morphology modification of eutectic (Si) and Al2Si2Ce phases by Sr addition stimulated the simultaneous improvement in strength and ductility in Al–Si–Mg–Ce alloy.

Bilayer period and ratio dependent structure and mechanical properties of TiN/MoN superlattices

Transition metal nitrides are widely used in the hard materials and protective coatings industry, but are limited by their low fracture toughness. Encouraged by previous studies on remarkable simultaneous improvements in strength and ductility through superlattice (SL) architectures, various TiN/MoN SL thin films were developed on MgO (100) substrates. By varying their bilayer periods (Λ) between 2 and 23 nm with bilayer ratios (Γ = ℓMoN:ℓTiN) of 0.5, 1, 2, and 2.7, their individual effects on structure and mechanical properties can be revealed. All SLs—independent of Λ, Γ, and nitrogen-to-metal (N/Me) ratio (within the analysed variations)—exhibit a rocksalt structure with high-order satellite peaks in X-ray diffraction. While the SLs with Γ = 2 have the lowest hardness (H)—presumably due to their overall lowest N/Me ratio—the SLs with Γ = 2.7 are the hardest with a neat superlattice effect. The SLs with Γ = 1 and 2.7 have a comparable superlattice effect on fracture toughness (KIC), peaking at Λ = 9.9 and 9.3 nm, respectively. Of all the SLs investigated, those with Γ = 1 provide the best blend of mechanical properties and dry sliding coefficient of friction (µ), such as H = 34.8±1.6 GPa, KIC = 4.1±0.2 MPa√m, and µ = 0.27 when Λ = 9.9 nm. Deepening current understanding of superlattice effects in general—particularly the influence of bilayer periods and ratios—in relation to the nitrogen supply and heterogeneous microstructures, our study accelerates the design of nanolayered coatings with desired structure-property combinations.

Enhancing strength and toughness of GNS/Al nanocomposites via a hybridization strategy

Good strength-ductility balance in graphene nanosheet (GNS)-reinforced aluminum nanocomposites can be achieved through tailorable and facile agglomeration control. Our previous study showed that pre-modulating the Al powder morphology by adding hard silicon carbide nanoparticles (SiCnp) during the two-step ball milling process effectively promotes the uniform dispersion of GNSs. However, excess SiCnp content causes SiCnp aggregate and premature cracking of composites. Here, GNS-reinforced aluminum nanocomposites with different SiCnp content (0.3–1.5 vol%) were prepared, and the optimal SiCnp-to-GNS ratio was determined after optimizing the SiCnp content in a pre-studied composite preparation process. The effect of SiCnp on the microstructure and mechanical properties of the composites was systematically investigated. The cold welding deformation of Al flakes increased with the SiCnp content. Nonetheless, inadequate or excessive SiC content caused insufficient lamination or excessive cold-weld stacking of Al flakes, respectively. Al-0.9vol.%SiCnp powders possessed the highest specific surface area which resulted in high homogeneous dispersion of 3.0 vol% GNS during the second ball-milling stage. Consequently, the resulting hybrid reinforced (GNS + SiCnp)/Al composites showed simultaneous improvement in strength and plasticity, unlike Al-3.0vol.%GNS composites. This showed that introducing hard nanoparticles (i.e., the hybridization strategy) is a promising method to simultaneously enhance strength and plasticity of aluminum nanocomposites.

Simultaneous improvement in strength and ductility of friction stir welded Mg/Al joints by reducing micro-intermixing

Thread of pin has been proved beneficial to increasing shear action of tool and material intermixing, which however induces abundant formation of intermetallic compounds (IMCs) in Mg/Al dissimilar friction stir welding (FSW) leading to deteriorating the performance of joints. In this work, Mg alloy and Al alloy were well joined by threaded pin and unthreaded pin under the same welding parameters. For threaded pin joints, cracks occured in the banded structure (BS) region and bottom interface, then the main crack propagated along the Mg/Al interface, resulting in low strength and elongation. For unthreaded pin joints, necking and fracture occurred at the softened Al alloy to the retreating side (SAA-RS), and the fracture mode changed from brittle fracture (Mode I) to ductile fracture (Mode III). The tensile strength and strain of unthreaded pin joints are 201 MPa and 7.14 % respectively, significantly higher than those of threaded pin joints (i.e. 140 MPa and 1.15 %), and is the highest combination of strength and strain reported up until now. An unthreaded pin could reduce the local micro-intermixing between Mg and Al to suppress the formation of IMCs, which reduced the hardness in the BS region, preventing the formation and propagation of cracks.

Simultaneous improvement of strength and uniform elongation of ferrite-bainite steel with heterogeneous networked microstructure

A novel heterogeneous networked dual-phase structure, composed of bainite grains surrounding the ferrite grains and forming a networked structure, was successfully introduced into the low-carbon ferrite-bainite steel through a two-step heat treatment process. The ferrite-bainite steel with the networked structure exhibited a high ultimate tensile strength of 872 ± 39 MPa, a good uniform elongation of 15.59 %, and a high total elongation of 22.79 %. Meanwhile, it possessed excellent work hardening behaviors compared to the ferrite-bainite steel with an island feature. The improvement of the comprehensive mechanical properties was attributed to the influence of hetero deformation induced (HDI) hardening and the synergistic deformation of the dual-phase structure.

Simultaneous improvement of strength and ductility in a P-doped CrCoNi medium-entropy alloy

A newly developed P-doped CrCoNi medium-entropy alloy (MEA) provides both higher yield strength and larger uniform elongation than the conventional CrCoNi MEA, even superior tensile ductility to the other-element-doped CrCoNi MEAs at similar yield strength levels. P segregation at grain boundaries (GBs) and dissolution inside grain interiors, together with the related lower stacking fault energy (SFE) are found in the P-doped CrCoNi MEA. Higher hetero-deformation-induced (HDI) hardening rate is observed in the P-doped CrCoNi MEA due to the grain-to-grain plastic deformation and the dynamic structural refinement by high-density stacking fault-walls (SFWs). The enhanced yield strength in the P-doped CoCrNi MEA can be attributed to the strong substitutional solid-solution strengthening by severer lattice distortion and the GB strengthening by phosphorus segregation at GBs. During the tensile deformation, the multiple SFW frames inundated with massive multi-orientational tiny planar stacking faults (SFs) between them, rather than deformation twins, are observed to induce dynamic structural refinement for forming parallelepiped domains in the P-doped CoCrNi MEA, due to the lower SFE and even lower atomically-local SFE. These nano-sized domains with domain boundary spacing at tens of nanometers can block dislocation movement for strengthening on one hand, and can accumulate defects in the interiors of domains for exceptionally high hardening rate on the other hand.

Tailoring hierarchical microstructures and nanoprecipitates in additive-manufactured Al-Zn-Mg-Cu-Nb alloys for simultaneously enhancing strength and ductility

Additive manufacturing provides an efficient way of producing metallic components with complex geometries. Their microstructure is substantially different to those from conventional processing, creating opportunities for manipulating the final microstructure and properties via heat treatment. Here, we demonstrate that as-built heterostructures in an Al-Zn-Mg-Cu-Nb alloy produced during the solidification of molten pools provide a driving force and additional Zener pinning sources for recrystallization. This creates a bimodal grain structure after solution treatment, causing additional hetero-deformation-induced strengthening and hardening. Coarse grains are found to promote work hardening and blunt the propagate of cracks during deformation, increasing ductility. Together with precipitation strengthening from a high number density nanoprecipitates, the simultaneous improvement of strength and ductility in a highly alloyed Al-Zn-Mg-Cu-Nb alloy is achieved. These results provide a simple strategy for the development of additively manufactured age-hardening alloys with improved strength and ductility for high performance structural applications.

Simultaneously improved the strength and ductility of cast Al-3Li-2Cu alloy by Ti addition and heat treatment

This work systematically investigated the impact of minor Ti addition and heat treatment on grain structure, precipitates, precipitate-free zone (PFZ), and the performance of the Al-3Li-2Cu alloy. Minor Ti addition significantly refines the as-cast alloy, leading to a transition from columnar grains to equiaxed grains. The primary Al3Ti phases, with a low mismatch (0.99%) to the matrix, act as heterogeneous nucleation sites for α-Al, while the presence of Ti solutes restricts grain growth. As a result, the average grain size can be refined to 35.2 μm by adding 0.2 wt% Ti. Besides, minor Ti addition affects the corresponding precipitation behavior of the alloy. Detailed TEM observations reveal that the addition of Ti inhibits the growth of δ’(Al3Li) precipitates and the accompanying δ’-PFZ, which should be related to the interaction between Ti solutes and vacancies. Besides, reducing the aging temperature exerts a similar effect. Finally, the 0.2 wt% Ti-modified alloy exhibits excellent mechanical properties after aging at 175 °C for 8 h. It demonstrates a high yield strength (272 MPa), a high ultimate tensile strength (399 MPa), and an acceptable elongation (5.9%), which represent an increase of 8.8%, 34.8%, and 293.3%, respectively, compared to the alloy without Ti addition. The simultaneous improvement in strength and ductility is attributed to the presence of fine and equiaxed grains, high-density and homogenous δ’ precipitates, and a narrow δ’-PFZ. In-depth discussions are provided to elucidate the underlying mechanisms governing the microstructure and mechanical properties.

Simultaneous improvement of strength and ductility in near β Ti alloy with (α + β) hybrid structure via intermediate phases transformation

The influences of simultaneous precipitation of isothermal ω and O′ on deformation mechanisms and mechanical properties of near β Ti alloy Ti-5Al-3Mo-3V-2Cr-2Zr-1Nb-1Fe with (α + β) hybrid structure are revealed. During continuous heating, the phase transformation sequence in this alloy is β + αp + ω-embryos + O′ → β + αp + ωiso + O′ → β + αp + ωiso + O′ + αs → β + αp + αs. Low-temperature heat treatments from 200 °C to 400 °C are carried out to develop such intermediate phases. Upon aging at 200 °C and 300 °C, the isothermal ω and O′ domains are continuously generated. In comparison with solution state, the deformation behaviors of aged samples are altered, and the yield stress and ductility are simultaneously increased. When aged at 200 °C, the yield strength is increased by 13.8 %, and fracture elongation is increased by 63.2 %. When aged at 300 °C, the yield strength is increased by 18.2 %, and preserves large ductility same to solution state. This is due to the development of isothermal ω and O′ domains suppress long-range stress induced martensitic transformation during loading, and the deformation mechanisms evolve into dislocations slipping gradually. When the aging temperature increases to 400 °C, α precipitation takes place leading to an obvious decrement in ductility. Upon loading the primary α can also accommodate partly the strains and relax local stress concentration. The results in this work clearly proves that better mechanical properties can be achieved through tailoring intermediate phases generation.

Simultaneous enhancement of strength and conductivity via self-assembled lamellar architecture

Simultaneous improvement of strength and conductivity is urgently demanded but challenging for bimetallic materials. Here we show by creating a self-assembled lamellar (SAL) architecture in W-Cu system, enhancement in strength and electrical conductivity is able to be achieved at the same time. The SAL architecture features alternately stacked Cu layers and W lamellae containing high-density dislocations. This unique layout not only enables predominant stress partitioning in the W phase, but also promotes hetero-deformation induced strengthening. In addition, the SAL architecture possesses strong crack-buffering effect and damage tolerance. Meanwhile, it provides continuous conducting channels for electrons and reduces interface scattering. As a result, a yield strength that doubles the value of the counterpart, an increased electrical conductivity, and a large plasticity were achieved simultaneously in the SAL W-Cu composite. This study proposes a flexible strategy of architecture design and an effective method for manufacturing bimetallic composites with excellent integrated properties.

Simultaneous improvement of strength and toughness via two-stage aging for a secondary hardening steel

A two-stage aging, involving initial low-temperature treatment followed by high-temperature treatment, was employed to induce a high number density M2C and inhibit the occurrence of chemical ordering and formation of large ellipsoidal particles at grain boundaries. The ultimate tensile strength, yield strength and Charpy impact energy increase by 233 MPa, 191 MPa and 3.3 J, respectively.

Simultaneous improvement of strength and ductility of laser additively produced Ti6Al4V by adding tantalum

Laser additive manufacturing (LAM) technique can efficiently fabricate Ti6Al4V components of complex shapes, but often show poor mechanical properties. In this study, tantalum (Ta) was added into Ti6Al4V as an alloying element to improve the overall mechanical performance using a laser cladding system. It was found that Ti6Al4V–4Ta (corresponding to 4 wt% Ta) exhibited excellent mechanical performance with the yield stress of 956 MPa, ultimate tensile strength of 1042 MPa and the elongation of 10.8 %, meeting the ISO 7209 requirements for titanium and titanium alloys. The synergistic improvement of strength-ductility of Ti6Al4V–4Ta was attributed to the microstructure refinement, weakened α-variants selection, Ta solid solution, modified dislocation density and β phase content. Further quantitative analysis demonstrated that the strength increase was mainly contributed from the additional grain boundary, solid solution and dislocation induced by Ta elemental alloying. This study established Ta elemental alloying as an effective method to simultaneously enhance the strength and ductility of Ti6Al4V alloy using LAM technology.

Simultaneous improvement of strength and plasticity of TZM alloys by introducing α-Al2O3 ceramic particles

A new α-Al2O3 ceramic particles reinforced TZM alloy material was prepared by powder metallurgy, exhibiting a better combination of strength and plasticity. Comprehensive tensile tests and detailed microstructure observations showed that compared with the TZM alloy. The ultimate tensile strength and uniform elongation of the TZM-0.9 wt% Al2O3 alloy increased by 22 % and 55 %, respectively, and all the strengthened TZM alloys exhibited typical toughness fracture characteristics. Based on theoretical analysis, strengthening is mainly caused by the mismatch of the elastic modulus between α-Al2O3 ceramic particles and the molybdenum matrix, accounting for 71 % of the increase in total strength. Mismatch of the elastic modulus can increase the dislocation density of the matrix around α-Al2O3 particles. In addition, α-Αl2O3 particles promote the rotation of grains along the <111> direction during plastic deformation, leading to activation of the slip system and promotes the improvement of plasticity.

Achieving superior strength-ductility balance in novel heterogeneous lamella structures of Al-Zn-Mg-Cu alloys

Heterogeneous structures (HS) materials have the potential to exhibit simultaneous improvement in strength and plasticity due to hetero-deformation-induced hardening (HDI) between multiple grain structures. However, achieving HS in aluminum alloy can be quite challenging. In this study, 7000 series aluminum alloys are investigated by incorporating rare earth element Y to develop a dual-phase structure containing Al8Cu4Y and Al3(Y, Zr) phases. And a heterogeneous lamella structure (HLS) is formed through the synergistic effect of Al8Cu4Y which includes dynamic recrystallization nucleation during deformation, and Al3(Y, Zr) which hinders the growth of recrystallized grain by means of pinning dislocations and subgrain boundaries. Substructures such as precipitates and nanocrystals are incorporated during the fabrication of HS, allowing for precise control over the volume fraction of fine grains by adjusting the ratio of two-scale second phases. When Y content reaches 0.3%, the 7Y55-2/heterogeneous lamella structure (HLS) samples exhibit a fine grain volume fraction of 76.5 vol.%, a tensile strength of 695 MPa, and an elongation of 16.6%. The alloy contains a large number of dislocations that preferentially induce the growth of η' phases along specific directions, thereby promoting their development. The multi-coupling effect and composite strengthening mechanisms in the “heterostructure-dislocation-precipitate” microstructure contribute to the intrinsic excellent strength and plasticity of the alloy. This study tackles the challenge of inverted strength and plasticity observed in Al-Zn-Mg-Cu-Zr alloys, offering novel insights that pave the way for further applications of heterogeneous materials.

Simultaneous improvement in strength and ductility of CT20 titanium alloy at cryogenic temperature

Quasi-static tensile deformation behaviors at room temperature (RT) and 77 K of the CT20 alloy with a <-12-11>//ND texture were investigated. The CT20 alloy with equiaxed microstructure exhibits excellent mechanical properties with simultaneous increase in strength and elongation at cryogenic temperature. In current study, the initial <-12-11>//ND texture promotes basal slip actuation effectively and continuously increases Schmid factor (SF) of other slip systems to promote multiple slip. Cryogenic temperature weakens the deformation texture due to the promotion of multiple slip. Since the decrease of the stacking fault energy (SFE), more twins in number and variety nucleate at 77 K and promote multiple slip. It causes strong cryogenic twinning-induced plasticity (TWIP) effect. Grain refinement induces strong cryogenic dynamic Hall-Petch effect resulting in high strain-hardening rate (SHR) and strength. The yield strength (YS, ∼1052.67 MPa), ultimate tensile strength (UTS, ∼1102.51 MPa) and elongation (EL, ∼21.1 %) of the 77 K specimen are about 84.1 %, 69.1 % and 38.8 % higher than its counterpart at RT, respectively. In addition, cryogenic temperature changes the initiation location of cracks and promotes cracks initiation at grain boundaries homogeneously.

Simultaneously enhancing strength and ductility of high-Nb-containing TiAl alloy via extrusion-assisted microstructure tailoring

In most metallic materials, the strength-ductility trade-off serves as an inevitable scenario. Therefore, improving the room/high-temperature strength/ductility of high Nb-TiAl alloys based on a lamellar microstructure is important for practical applications. In this work, a novel microstructure with fine lamellar colonies and a certain number of residual γ grains was developed through hot extrusion in the near α phase region. The results indicated that the lamellar colony size and spacing of the as-cast alloy were significantly refined by hot extrusion. The as-extruded Ti-45Al-8Nb-(W, B, Y) alloy demonstrated a good combination of high strength and ductility. The tensile strength and ductility were 1129 MPa and 2.04% at room temperature (RT), respectively, and 744 MPa and 51.20%, respectively, at 850 °C. A simultaneous improvement in strength and ductility below ductile-brittle transition temperature (DBTT) could be attributed to the abundant deformation twins and their intersections, as well as prominent strain working caused by high-density dislocations in the γ phase. Due to dynamic recrystallization, the ductility was significantly enhanced when stretched over DBTT. This extrusion-assisted microstructure tailoring strategy could be extended to other TiAl systems and may serve as a useful solution for addressing the significant engineering constraints posed by the low RT ductility and poor hot-working capabilities of high Nb-TiAl alloys.