Sensitive Detector Research Articles

On Learning the Invisible in Photoacoustic Tomography with Flat Directionally Sensitive Detector

On Learning the Invisible in Photoacoustic Tomography with Flat Directionally Sensitive Detector

The torsion pendulum dual oscillator for low-frequency Newtonian noise detection

We present a torsion pendulum dual oscillator sensor designed toward the direct detection of Newtonian noise. We discuss the sensitivity limitations of the system, experimental performance characterization results, and prospectives to improve performance. The sensor is being developed to contribute to the mitigation of Newtonian noise impacts in the sensitivities of next generation terrestrial gravitational-wave detectors.

Monte Carlo simulation of a simple and fast method to experimentally determine the partial sensitivity of a bare LR-115 detector using planar alpha sources

Partial sensitivity of the bare LR-115 detector (KB) to radon or thoron, or any of their airborne progeny, is an essential component in the detector's calibration factor. Its experimental determination is complex, requires expensive and sophisticated instruments and facilities, and is time consuming. Using the TRACK_TEST and SRIM programs, and Monte Carlo simulations, the possibility of a simple and fast method to determine KB experimentally was demonstrated. The method is based on calculations of the average value of detection efficiencies (i.e., the cumulative efficiency) for alpha particles emitted by a planar alpha source placed at different distances from detectors. Source radius can be estimated from the energy of emitted alpha particles, detector radius, and parameters dependent on etching conditions. Varying the emission energy of alpha particles, the source and detector radii, and the source-detector distance step length, an average value of 0.02 tracks. cm−2 per Bq.d.m−3 (0.22 cm) was obtained assuming standard etching conditions. In addition to alpha electrodeposited sources, sealed sources such as those built with anodized aluminium sheets proved to be suitable for this proposal. Experimentally, KB can be estimated from: track densities registered in detectors exposed at different distances from the source, range of distances that produce visible tracks, and source activity. The developed method is much simpler and faster than the conventional method that uses standard sources of radon and its progeny and large chamber with controlled conditions.

Detection of Virus SARS-CoV-2 Using a Surface Plasmon Resonance Device Based on BiFeO3-Graphene Layers.

Coronavirus disease (COVID-19) pandemic outbreak is being investigated by severe respirational syndrome coronavirus-2 (SARS-CoV-2) as a global health issue. It is crucial to propose sensitive and rapid coronavirus detectors. Herein, we propose a biosensor based on surface plasmon resonance (SPRE) for the detection of SARS-CoV-2 virus. To achieve improved sensitivity, a BiFeO3 layer is inserted between a metal (Ag) thin film and a graphene layer in the proposed SPRE device so that it has the structure BK7 prism/ Ag/ BiFeO3/ graphene/ analyte. It has been demonstrated that a small variation in the refractive index of the analyte can cause a considerable shift in the resonance angle caused by the remarkable dielectric properties of the BiFeO3 layer, which include a high index of refraction and low loss. The proposed device has shown an extremely high sensitivity of 293 deg/RIU by optimizing the thicknesses of Ag, BiFeO3, and the number of graphene sheets. The proposed SPRE-based sensor is encouraging for use in various sectors of biosensing because of its high sensitivity.

High-power laser beam in higher-order Hermite–Gaussian modes

The sensitivities of current gravitational-wave detectors are limited around signal frequencies of 100 Hz by mirror thermal noise. One proposed option to reduce this thermal noise is to operate the detectors in a higher-order spatial laser mode. This operation would require a high-power laser input beam in such a spatial mode. Here, we discuss the generation of the Hermite–Gaussian modes HG2,2, HG3,3, and HG4,4 using one water-cooled spatial light modulator (SLM) at a continuous-wave optical input power of up to 85 W. We report unprecedented conversion efficiencies for a single SLM of about 43%, 42%, and 41%, respectively, and demonstrate that the SLM operation is robust against the high laser power. This is an important step toward the implementation of higher-order laser modes in future gravitational-wave detectors.

Impact on dosimetry of occupationally exposed individuals on the patient management for PET/MRI studies: a comparison study with dosimetry on PET/CT

PET/MRI technology has expanded the boundaries of investigation in nuclear medicine, supported by the high sensitivity of solid-state PET detectors. Nonetheless, the coil positioning might lead to an increased exposure period of the worker to the injected patient. This procedure does not occur on PET/CT and, therefore, exposure period is reduced on such scanner. The aim of our study was to evaluate the dosimetry of two occupationally exposed individuals (OEI) working at the Center of Nuclear Medicine of Hospital das Clínicas of the University of Sao Paulo. We used thermoluminescent (TLD) dosimeters in pulse, whole-body and crystalline for PET/MRI and PET/CT procedures during five months of clinical and research routine. We also monitored the time for positioning/removing the patient on both scanners. For this study, OEI1 performed 76 PET/MRI studies and 102 PET/CT studies while OEI2 performed 26 and 56 PET/MRI and PET/CT studies, respectively. We found no evidence of differences for the whole-body dose values between both scanners (p = 0.22). The average time of patient management (positioning/removing the patient) was 14.38, and 3.81 minutes for PET/MRI and PET/CT, respectively. When the normalization by the number of PET/CT studies was applied, we found no statistical difference for effective and equivalent dose values. Our study encourages future investigations on nursing staff, which is a critical population that is exposed to ionizing radiation, mainly on dynamic studies, due to the synchronized injection with the protocol starting.

Highly Sensitive Direct X-Ray Detector Based on Copper(II) Coordination Polymer Single Crystal with Anisotropic Charge Transport.

Anisotropic charge transport plays a pivotal role in clarifying the conductivity mechanism in direct X-ray detection to improve the detection sensitivity. However, the anisotropic photoelectric effect of semiconductive single crystal responsive to X-ray is still lacking of theoretical and experimental proof. The semiconductive coordination polymers (CPs) with designable structures, adjustable functions, and high crystallinity provide a suitable platform for exploring the anisotropic conductive mechanism. Here,the study first reveals a 1D conductive transmission path for direct X-ray detection from the perspective of structural chemistry. The semiconductive copper(II)-based CP 1 single crystal detector exhibits unique anisotropic X-ray detection performance. Along the 1D π-π stacking direction, the single crystal device (1-SC-a) shows a superior sensitivity of 2697.15µCGyair -1 cm-2 and a low detection limit of 1.02µGyair s-1 among CPs-based X-ray detectors. This study provides beneficial guidance and deep insight for designing high-performance CP-based X-ray detectors.

Stochastic versus dynamic resonant activation to enhance threshold detector sensitivity

The Josephson junction, as a threshold detector, is studied in the presence of noise and a weak external signal in the framework of the pendulum model. A range of parameters, efficient for weak signal detection has been found. While in the low noise limit the signal can be enhanced via dynamic resonant activation mechanism, even weaker signals can be efficiently detected with the help of noise via stochastic resonant activation mechanism. The parameter optimizations of a microwave single photon counter prototype based on aluminum Josephson junction are discussed.

Position sensitive detector based non-contact vibration measurement with laser triangulation method utilizing Gabor Transform for noise reduction

Measurement of vibration without having contact with the target is crucial for many applications. However, real time vibration signals are frequently mixed with various levels of dynamic noises. In this research, a non-contact type vibration measurement system based on laser triangulation method is proposed by using a PSD (Position sensitive detector) and here a single axis Brüel and Kjaer piezoelectric accelerometer is used to validate the experimental results. The primary goal of this measurement system is to develop a Gabor Transform based signal denoising technique, in order to eliminate noise from the real-time vibration data. Furthermore, PSD platform vibration, which might cause unanticipated inaccuracies in the detected vibration data, has also been eliminated by utilizing a self-vibration compensation approach using an ADXL-345 three-axis accelerometer. The self-vibration compensated vibration measurement technique has been designed using an NI (national instruments) cRIO (CompactRIO) 9074 real-time FPGA (field programmable gate array) based embedded controller. Consequently, a Gabor Transform and Expansion-based Signal Processing Technique is designed using NI cRIO-9074 real time platform to reduce external noise from the self-vibration compensated vibration data. It has been observed that the implementation of Gabor Transform has improved the performance of the system in term of enhancing the SNR (Signal-to-noise ratio).

Improving the ranging performance of chaos LiDAR.

Chaos lidar has gained significant attention due to its high spatial resolution, natural anti-interference capability, and confidentiality. However, constrained by the power of the chaos laser, the sensitivity of the linear detector, and the hardware bandwidth, chaos lidar is greatly restricted in the application of long-distance target detection and imaging. To overcome these constraints, we propose a novel, to the best of our knowledge, chaos lidar based on Geiger mode avalanched photodetectors (GM-APDs) in a previous study called chaos single-photon (CSP) lidar. In this paper, we compare the CSP lidar with the linear mode chaos lidars by combining with lidar equation. Regarding the ranging principle, the CSP lidar is fully digital and breaks through the constraints of a detector's bandwidth and ADC's sampling rate. The simulation results indicate that the detection range of the CSP lidar is approximately 35 times and 8 times greater than that of a continuous-wave chaos lidar and pulsed chaos lidar, respectively. Although the detection accuracy of the CSP lidar is only at the centimeter level and is lower than the linear mode chaos lidars, its consumption of storage resources and power is greatly reduced due to 1-bit quantization in the GM-APD. Additionally, we investigate the impact of GM-APD parameters on the signal-to-noise ratio (SNR) of the CSP lidar system and demonstrate that the dead time difference between GM-APDs has a negligible effect. In conclusion, we present and demonstrate a new chaos lidar system with a large detection range, high SNR, low storage resources and power consumption, and on-chip capability.

A data acquisition and reconstruction software for SAMPA-SRS integration

In this work we present the latest developments in the SAMPA-SRS integration. Asoftware was developed to improve the acquisition configuration, acquisition, and decoding of the data. The complete framework was tested using a triple GEM-based position sensitive detector for X-rays. The detector was operated in Ar/CO2 (70/30) in continuous flow, at atmospheric pressure and made use of a 1 dimension strip readout (200 μm wide strips at a pitch of 400 μm) for charge collection. With this detector a position resolution of better than 833 μm was obtained, with an energy resolution of 14.2 % (σ/E) for 5.9 keV.

Gravitational wave from graviton Bremsstrahlung during reheating

We revisit graviton production via Bremsstrahlung from the decay of the inflaton during inflationary reheating. Using two complementary computational techniques, we first show that such 3-body differential decay rates differ from previously reported results in the literature. We then compute the stochastic gravitational wave (GW) background that forms during the period of reheating, when the inflaton perturbatively decays with the radiative emission of gravitons. By computing the number of relativistic degrees of freedom in terms of Δ N eff, we constrain the resulting GW energy density from BBN and CMB. Finally, we project current and future GW detector sensitivities in probing such a stochastic GW background, which typically peaks in the GHz to THz ballpark, opening up the opportunity to be detected with microwave cavities and space-based GW detectors.

Searching for the causes of anomalous Advanced LIGO noise

Advanced LIGO and Advanced Virgo have detected gravitational waves from astronomical sources to open a new window on the Universe. To explore this new realm requires an exquisite level of detector sensitivity, meaning that the much stronger signal from instrumental and environmental noise must be rejected. Selected examples of unwanted noise in Advanced LIGO are presented. The initial focus is on how the existence of this noise (characterized by particular frequencies or time intervals) was discovered. Then, a variety of methods are used to track down the source of the noise, e.g., a fault within the instruments or coupling from an external source. The ultimate goal of this effort is to mitigate the noise by either fixing equipment or by augmenting methods to suppress the coupling to the environment.

Gravitational wave signals from leptoquark-induced first-order electroweak phase transitions

We consider the extension of the Standard Model (SM) with scalar leptoquarks in SU(2) singlet, doublet and triplet representations. Through the coupling between leptoquark and the SM Higgs field, the electroweak phase transition (EWPT) can turn into first-order and consequently produce gravitational wave signals. We compute the required value of the leptoquark-Higgs for first-order EWPT to happen and discuss about the possible constraint from Higgs phenomenology. Choosing some benchmarks, we present the strength of the gravitational waves produced during the leptoquark-induced first-order EWPT and compare them to detector sensitivities. We find that the SU(2) representations of the leptoquark can be distinguished by gravitational waves in the parameter space where first-order EWPT can happen as a function of the Higgs portal coupling.

Vehicle-Mounted Solar Occultation Flux Fourier Transform Infrared Spectrometer and Its Remote Sensing Application.

For the demand of rapid monitoring of pollution gas disorganized emissions in industrial parks, this paper studies the solar fast tracker system of vehicle-mounted SOF-FTIR (Solar Occultation Flux Fourier Transform Infrared Spectroscopy) system, where the spectrometer directly measures the broadband absorption spectrum of solar radiation light. A fast portable solar tracking system based on PSD (position sensitive detector) is designed, the mathematical model of solar spot position on the PSD surface source is established, and the optimal optical design parameters are simulated using the model. The dead-zone integral separation PID (Proportion Integration Differentiation) control algorithm is used to track the trajectory of the solar, and the light spot position model is used to nonlinearly compensate the output of PID control so that the PID controller has the same control precision and response speed in different error areas. Experimental analysis of the solar tracking performance of the vehicle-mounted SOF-FTIR under static and dynamic conditions, as well as the spectral effects on the measurements under static vehicle, constant speed, and turning driving conditions. The remote sensing application experiment of vehicle-mounted SOF-FTIR pollution gas emission flux was carried out in a tire factory in Hefei City, Anhui Province. A vehicle-mounted SOF-FTIR system realized the qualitative and quantitative analysis of the pollution gas at the boundary of the tire plant and calculated the flux of each component pollution gas. The emission flux of pollution gas was highly consistent with the actual pollution distribution of the tire plant. The results show that the positioning accuracy of PSD in the vehicle tracking experiment can also meet SOF-FTIR requirements for solar tracking. The remote sensing system will be useful in the field of atmospheric environment monitoring, and the mobile monitoring of regional pollutant gases based on solar infrared spectroscopy has application value.

Sea Surface Moving Target Detection Using a Modified Keystone Transform on Wideband Radar Data

The echoes collected by wideband radar systems provide abundant information on target scatterers, which is beneficial to target detection, classification, and recognition. However, as the radar range resolution increases, range cell migration (RCM) during the coherent integration (CI) period happens much easier, which may cause a degradation of target detection probability. In addition, due to the target’s orientation and structure relative to the radar, the distribution characteristics of the target scatterers in high-resolution range profiles (HRRPs) and the detection window length may vary from pulse to pulse, which may reduce the performance of traditional energy integration (EI) detectors. To solve those problems, moving range-spread target (RST) detection combining the modified keystone transform (MKT) and improved EI (IEI) is proposed in this paper. Firstly, based on waveform entropy minimization, MKT using hunter–prey optimization (HPO) is introduced to reduce the CI gain loss. The target Doppler ambiguity factor is estimated using such an effective optimization technique. Then, the IEI detector optimized by the adaptive threshold and detection window is utilized to achieve target detection, which minimizes the sensitivity of the traditional EI detector to the detection window length. The proposed method significantly improves the performance of moving RSTs in sea clutter without prior knowledge of the target Doppler ambiguity factor. Experiments are conducted by comparing the proposed method with other competing methods on both simulation data and real sea clutter data. The results demonstrate that the proposed method can obtain the CI more efficiently and has a higher detection probability.

Estimation of underwater acoustic direction-of-arrival using the probe beam deflection technique.

This paper proposes a method of estimating the underwater acoustic direction-of-arrival using several laser beams impinging on a propagating underwater acoustic wave. The deflection of the laser beam caused by the spatial variation of the optical refractive index, which is further due to the modulation of the acoustic wave, reflects the information of direction-of-arrival and is sensed by the position sensitive detector (PSD). The sensing of the minute displacement on the PSD, in fact, introduces an extra dimension in the depth direction, which is a significant advantage over the conventional piezoelectric sensing regime. The employment of the extra sensing dimension can overcome several shortcomings, represented by spatial aliasing and phase ambiguity, existing in the current direction-of-arrival estimating methods. In addition, the ringing phenomenon of the piezoelectric effect is greatly reduced in the proposed laser-based sensing regime. By the flexibility of placing the laser beams, a prototype of the hydrophone is designed and manufactured, and a series of testing is performed. The results show that, benefiting from the probe beam deflection technique and combining the rough estimate and fine calculation, the resolution of the underwater acoustic direction-of-arrival can be improved to better than 0.016°, which can support and reform many underwater applications such as underwater acoustic communication, underwater detection, and ocean monitoring.

Ultrafast carrier dynamic anisotropy of single crystal rhenium disulfide flake based on transient absorption spectroscopy

In recent years, rhenium disulfide (ReS2) has attracted much attention in polarization dependent photonic applications due to its anisotropic optoelectronic response. To reveal the anisotropic response mechanisms, single crystal layered ReS2 flake with lateral size of about 10 μm is obtained using mechanical exfoliation method, and the ultrafast carrier dynamics of an individual flake is studied using transient absorption microscopy. The excited carrier concentration of layered ReS2 flake exhibits obvious polarization dependence of the pump light, which is caused by the anisotropic linear absorption and electron mobility rates in different orientations. These results could provide more references for the application of ReS2 in polarization sensitive detectors and optoelectronic devices.

Highly sensitive measurement method for photosensitizers based on dual-excitation laser modulation technique

A dual-excitation laser modulation technique for the sensitive measurement of photosensitizers in tumor is proposed. The technique is based on the difference in optical absorption properties of photosensitizers and biological tissues at 405 nm and 450 nm. The 405 nm and 450 nm laser beams, with the same modulation frequency and 180° phase difference, were coupled into a single fiber simultaneously. A periodic signal with a frequency of 1 kHz was generated in alternating excitation, and was processed by phase sensitive detectors. The weak photosensitizer fluorescence masked by tissue autofluorescence can be effectively separated through the proposed method, so that the final signal intensity is only related to the concentration of photosensitizer. The method with a sensitivity of 0.22 mL/ng was determined by measuring the low concentration of protoporphyrin IX (PpIX) solution, and the detection limit of instrument reached 0.5 ng/mL. The puncturable optical probe with a diameter of 675 µm ensures that PpIX in can be detected with spatial resolution, which was performed in the measurement of PpIX in tumor bearing nude mice.

Sparse Lissajous scanning reflectance confocal microscope with an adjustable field of view and fast iterative Fourier filtering reconstruction.

Medical imaging devices are becoming increasingly compact, necessitating optimization research into different methods of actuation. Actuation influences important parameters of the imaging device such as size, weight, frame rate, field of view (FOV), and image reconstruction for imaging devices point scanning techniques. Current literature around piezoelectric fiber cantilever actuators focuses on device optimization with a fixed FOV but neglects adjustability. In this paper, we introduce an adjustable FOV piezoelectric fiber cantilever microscope and provide a characterization and optimization procedure. To overcome calibration challenges, we utilize a position sensitive detector (PSD) and address trade-offs between FOV and sparsity with a novel inpainting technique. Our work demonstrates the potential for scanner operation when sparsity and distortion dominate the FOV, extending the usable FOV for this form of actuation and others that currently only operate under ideal imaging conditions.