Saturable Absorber Research Articles

Ag/MXene as Saturable Absorber for Tm:Ho Co-Doped Q-Switched Fiber Laser.

Q-switched fiber lasers have become reliable light sources for generating high-energy pulses, which can be passively modulated by saturable absorbers with excellent nonlinear optical properties. The composite combining Ag and MXene exhibits a broadband nonlinear response and high modulation depth, making it a promising candidate for saturable absorbers in pulsed lasers. Herein, we demonstrate a Q-switched Tm:Ho co-doped fiber laser centered at 2 µm, where the Ag/MXene composite serves as a saturable absorber to generate pulses. The typical spectrum, pulse train, and radio frequency spectrum of Q-switched pulses were observed, in which the 60 dB signal-to-noise ratio was higher than that of 2 µm Q-switched fiber lasers based on other materials, demonstrating the stability of the output pulses. Additionally, the long-term stability of the laser was evaluated over 2 h, where the well-maintained central wavelength and output power also indicated the robustness of the Q-switched laser. Furthermore, the influence of the pump power on the parameters of Q-switched pulses was also investigated, which is conducive to control the output characteristics of lasers. Specifically, the pulse width of the Q-switched pulse decreased, while the repetition rate, output power, and single pulse energy all increased with the increase in pump power. These experimental results demonstrate the ability of Ag/MXene as a saturable absorber and show its potential for generating high-performance pulses in ultrafast lasers.

Study on Saturable Absorption Characteristics of Bi2Se3 Topological Insulators with Film Thickness Dependence and Its Laser Application

In our work, a multi-layer topological insulator (TI) Bi2Se3 thin film was prepared by the chemical vapor deposition method (CVD), and its saturable absorption and damage characteristics were experimentally studied. The results show that when the wavelength is 1064 nm, the saturable absorption parameters of TI: Bi2Se3 film, including modulation depth αs, non-saturable loss αns, and saturation power intensity Isat, increase with the increase in film thickness, and the damage threshold is inversely proportional to the film thickness. The thicker the film layer, the lower the damage threshold. Among them, modulation depth αs is up to 51.2%, minimum non-saturable loss αns is 1.8%, maximum saturation power intensity Isat is 560.8 kW/cm2, and the damage threshold is up to 909 MW/cm2. The influence of the controllable thickness of TI: Bi2Se3 film on passive Q-switching and mode-locking performance of laser is discussed and analyzed when TI: Bi2Se3 film is prepared by the CVD method as a saturable absorber (SA). Finally, the performance of TI: Bi2Se3 thin film applied to nanosecond laser isolation at the 1064 nm band is simulated and analyzed. It has the natural advantage of polarization independence, and the maximum isolation can reach 16.4 dB.

Q-switched pulse generation in L-band region with polyacrylonitrile saturable absorber

In this study, we assess the practicality of using Polyacrylonitrile (PAN) as a saturable absorber (SA) for generating Q-switched pulses within an erbium-doped fibre laser (EDFL) cavity. A successful combination of PAN, a resin material, and polyvinyl alcohol resulted in the formation of a SA film. This film was utilised to generate stable Q-switched pulses operating in a long-wavelength band of 1572 nm. The greatest repetition rate achieved was 66.1 kHz, while the minimum pulse width was 2.43 μs. The maximum pulse energy was achieved at 52 nJ and measured at a pump power of 175.9 mW. To the best of our knowledge, this study is the first report of EDFL passive Q-switching employing a PAN absorber.

Improved near-resonant two photon absorption of α-MnO2 nanowires surface functionalized reduced graphene oxide sheets

The versatile study of graphene derivatives has resurgence of interest on understanding its nonlinear optical response at different nanoscales. Nanostructured manganese dioxide: reduced graphene oxide (MnO2: rGO) hybrids were synthesized by reduction method by varying the content of rGO (5, 10, 15 & 20 wt%). X-ray Photoelectron Spectroscopy studies confirmed the surface functionalization of MnO2 on rGO. Field Emission Scanning Electron Microscopy (FESEM) and High-Resolution Tunnelling Electron Microscopy (HRTEM) witness that with respect to the content of rGO, the morphology of MnO2 varies radically from clusters to nanorods to nanowires over the surface of rGO sheets. Ground state absorption spectra of the hybrids have absorption edge at 268 nm corresponding to combined metal oxide charge transfer between rGO (π-π* transition of CC and n-π transition of C-O bonds) and MnO2 (d-d transition). Moreover, hierarchical MnO2 nanowire network resided on 2D rGO sheets involves broad absorption at the visible spectral domain due to polaron transition as well the localization of π- π* transited electrons that facilitates the probability of occurrence of excited state absorption. Intensity dependent open aperture Z-scan technique of the prepared hybrids using Q-switched Nd: YAG 532 nm nanopulsed laser reveals unusual transitions and enhanced nonlinear absorption. MnO2:(5 wt%) rGO shows saturable absorption (SA) at low intensity and changeover dynamically to reverse saturable absorption (RSA) at higher intensity. MnO2:(10 & 15 wt%) rGO exposes coupled nonlinear absorption (SA + RSA) owing to the combined effect of graphene (π-states) and MnO2 (σ-states). MnO2:(20 wt%) rGO exhibits a stronger RSA ascribed to sequential two photon absorption. The third-order nonlinear absorption coefficient and limiting threshold of MnO2: rGO (20 wt%) are 4.04 ×10-10 m/W and 0.84 ×1012 W/m2, which shows five-fold increase compared to bare rGO and MnO2. The obtained results propose that the optical nonlinearity of MnO2 nanowires surface functionalized rGO sheets can significantly be tuned to meet the requirements for fabricating laser safety devices.

Spectroscopy and efficient dual-wavelength laser performances of a Nd:GYSAG crystal.

We reported on the spectral properties and dual-wavelength laser performances of a novel, to the best of our knowledge, Nd:Gd1.8Y1.2ScAl4O12 (Nd:GYSAG) crystal for the first time. The absorption spectra, emission spectra, and fluorescence lifetime were systematically investigated. Further, a continuous-wavelength (CW) laser output power up to 5.02 W was obtained under an absorbed pump power of 9.45 W with slope and optical-to-optical efficiencies of 59.4% and 53.1%, respectively, at 1061.2 and 1063.2 nm. A stable passively Q-switched (PQS) laser employing Cr:YAG as a saturable absorber (SA) was realized. The maximum average output power of 0.756 W with a slope of near 34.4% was obtained with the pulse width, pulse energy, and peak power of 14.0 ns, 128.1 µJ, and 9.15 kW, respectively. The results indicate that the Nd:GYSAG crystal is an excellent laser medium for generating a high-efficiency dual-wavelength laser and has potential in terahertz (THz) laser generation.

Ternary ReS2(1-x)Se2xalloys of different composition for Q-switched and mode-locked all-fiber laser.

This paper systematically studied the composition-controlled nonlinear optical properties and pulse modulation of ternary ReS2(1-x)Se2xalloys for the first time. The compositionally modulated characteristics of ReS2(1-x)Se2xon the band gap were simulated based on the first principles. We investigated the effect of the band gap on the saturable absorption properties. In addition, we demonstrated the modulation characteristics of different components ReS2(1-x)Se2xon 1.5μm Q-switched pulse performance. The Q-switched threshold, repetition rate, and pulse duration increase as the S(sulfur)-element composition rise. And pulse energy also was affected by the S(sulfur)-element composition. The ReS0.8Se1.2SA was selected to realize a conventional soliton with high energy in the all-fiber mode-locked laser. The pulse was centered at 1562.9 nm with a pulse duration of 2.26 ps, a repetition rate of 3.88 MHz, and maximum pulse energy of 1.95 nJ. This work suggests that ReS2(1-x)Se2xhas great potential in laser technology and nonlinear optics, and widely extends the material applications in ultrafast photonics.

Dual-wavelength synchronously mode-locked Cr:LiSAF laser with a tunable beating frequency and a central wavelength.

We demonstrate a versatile dual-wavelength synchronous mode-locking of a diode-pumped Cr:LiSAF laser for the first time, to our knowledge. A two-color mode-locked operation is achieved by using intracavity birefringent filters (BRFs) or etalons as frequency-selective elements. Using filters with different thicknesses and hence different free spectral ranges (FSRs), wavelength separation in two-color mode-locking could be selected between 1 and 9 nm, with corresponding beating frequencies in the 0.4-3.5 THz range. Moreover, the central wavelength of the two-color output could be tuned smoothly between 840 and 875 nm, only limited by the bandwidth of the semiconductor saturable absorber mirror (SESAM) used for mode-locking. The method, which enables easy adjustment of the central wavelength and beating frequency of a dual-wavelength operation, is suitable for use in other laser gain media as well.

The water absorption capacity of 21 Sphagnum species

Sphagnum moss (peat moss) is the dominant land plant in peatlands, and it plays an essential role in peatland ecosystems because its remarkable water-holding capacity helps to conserve water resources and maintain the anoxic environment of peatlands. Sphagnum moss exhibits a super ability to absorb water. However, the water absorption capacity of different species and different parts of the same species is not well understood. In this study, we measured the short-term and saturated water absorption of 21 Sphagnum species from China. The results showed that the water absorption capacity of the investigated peat mosses was much higher than that of other bryophytes. Sphagnum imbricatum had the highest saturated water absorption capacity (about 44 times its dry weight), while the peat moss with the lowest saturated water absorption was Sphagnum flexuosum (about 19 times its dry weight). In addition, we determined the relative volume of hyalocysts of the spreading and pendent branch leaves of 18 Sphagnum species and further measured the water absorption capacity of the pendent branch, spreading branch, and stem of six of them. The results revealed that both pendent and spreading branches had strong water absorption capacity and were the primary water-absorbing parts of peat mosses. The water-absorbing capacity of different Sphagnum species was linearly related to the volume of hyalocysts. The results provide an essential scientific basis for selecting high-quality germplasm resources of peat moss.

Comparative study of the kinetic behaviors and properties of aromatic and aliphatic bismaleimides

In this paper, three aromatic bismaleimides (BMI-70, BMI-DE and BMI-80) and two aliphatic bismaleimides (BMI-DDA and BMI-C36) were synthesized. The structures were characterized using nuclear magnetic resonance (NMR) spectra and Fourier transform infrared (FT-IR) spectra. Their polymerization behaviors were discussed by non-isothermal differential scanning calorimetry (DSC). The thermal and dielectric properties of the poly(bismaleimide) were investigated using thermogravimetric analysis (TGA), dynamic thermo-mechanical analysis (DMA), and an impedance analyzer. The results indicate that the aliphatic bismaleimides exhibit lower apparent activation energies and dielectric properties, with BMI-DDA displaying an average activation energy of 105.5 kJ mol−1 and the dielectric constant of P(BMI-C36) is 2.558 @ 10 MHz. The aromatic polybismaleimides possessed better thermal stability, among which, the 5 % thermal decomposition temperature (Td,5) of P(BMI-70) was 513.5 °C, and the residual carbon rate at 800 °C was 44.6 %. In additional, water absorption was studied and their saturated water absorption was less than 4 %.

Broadband and ascendant nonlinear optical properties of the wide bandgap material GaN nanowires

Gallium nitride (GaN) nanowire, as a type of wide bandgap nanomaterial, has attracted considerable interest because of its outstanding physicochemical properties and applications in energy storage and photoelectric devices. In this study, we prepared GaN nanowires via a facile chemical vapor deposition method and investigated their nonlinear absorption responses ranging from ultraviolet to near-infrared in the z-scan technology under irradiation by picosecond laser pulses. The experiment revealed that GaN nanowires exhibit remarkable nonlinear absorption characteristics attributed to their wide bandgap and nanostructure, including saturable absorption and reverse saturable absorption. When compared to bulk GaN crystals, the nanowires provide a richer and more potent set of nonlinear optical effects. Furthermore, we conducted an analysis of the corresponding electronic transition processes associated with photon absorption. Under high peak power density laser excitation, two-photon absorption or three-photon absorption dominate, with maximum modulation depths of 73.6%, 74.9%, 63.1% and 64.3% at 266 nm, 355 nm, 532 nm, and 1064 nm, respectively, corresponding to absorption coefficients of 0.22 cm/GW, 0.28 cm/GW, 0.08 cm/GW, and 2.82 ×10−4 cm3/GW2. At lower peak energy densities, GaN nanowires demonstrate rare and excellent saturation absorption characteristics at wavelength of 355 nm due to interband transitions, while saturable absorption is also observed at 532 nm and 1064 nm due to band tail absorption. The modulation depths are 85.2%, 41.9%, and 13.7% for 355 nm, 532 nm, and 1064 nm, corresponding to saturation intensities of 3.39 GW/cm2, 5.58 GW/cm2 and 14.13 GW/cm2. This indicates that GaN nanowires can be utilized as broadband optical limiters and high-performance pulse laser modulating devices, particularly for scarce ultraviolet optical limiters, and saturable absorbers for ultraviolet and visible lasers. Furthermore, our study demonstrates the application potential of wide bandgap nanomaterials in nonlinear optical devices.

Generation of soliton molecules in a 1.5-μm ultrafast fiber laser based on Zinc 2,5-dihydroxyterephthalate saturable absorber

Two-dimensional (2D) Zinc 2,5-dihydroxyterephthalate (Zn-MOF-74) is a kind of metal–organic framework (MOF), which has been intensively studied in gas adsorption, gas storage, and catalysis. However, the potential applications of Zn-MOF-74 in the fields of optics, especially in the areas of nonlinear optical response and ultrafast optics need further exploration. Here, the nonlinear optical properties of Zn-MOF-74 are systematically investigated. In this work, we demonstrate that it gradually becomes saturated with the increase of the intensity of the incident pulse, which makes Zn-MOF-74 an effective saturable absorber in a mode-locked Er-doped fiber laser for ultrashort pulse generation. Our experiments yield stable single solitons as well as soliton molecules with tunable characteristics. When the pump power is 126 mW, conventional solitons with an output power of 2.35 mW and a pulse width of 0.93 ps are obtained. The generated pulses characterize a central wavelength of 1554.84 nm and a 3-dB bandwidth of 3.07 nm. By adjusting the pump power and polarization appropriately, the center wavelength of the soliton molecules is tunable from 1532.76 nm to 1554.24 nm. The experimental observations further proves that Zn-MOF-74 has great potential in ultrafast optics.

High-output ∼3 μ m MIR pulsed laser enabled by surface state regulation in PtTe2 optical switch

Mid-infrared (MIR) pulsed lasers operating in the ∼3 μm region play a crucial role in various applications, including molecular spectroscopy, ultrafast molecular imaging, and laser-assisted surgery. Despite recent advancements in MIR gain platforms, a notable technological challenge remains in the absence of an effective optical Q-switch. Here, a remarkable optical Q-switch in the 3 μm region based on a Dirac semimetal PtTe2 saturable absorber is realized. By modulating the surface state of PtTe2, the pulsed laser exhibited an increase in average power, escalating from 521 to 588 mW, accompanied by a significant decrease in pulse width from 368 to 187 ns. Nondegenerate pump–probe measurements showed that the recombination rate of the photocarrier in thinner PtTe2 nanoplates was effectively accelerated, primarily attributed to the substantial increase in surface state density, leading to better saturable absorption performance. As the thickness of the PtTe2 nanoplates decreases, the nonsaturable loss decreases from 12% to 3%, while the modulation depth increases from 6% to 12%. The enhanced ultrafast nonlinear absorption enables flexible modulation of saturation absorption parameters, which endows high-performance MIR pulsed laser generation.

Long-term properties evolution and life prediction of glass fiber reinforced thermoplastic bending bars exposed in concrete alkaline environment

Glass fiber reinforced polypropylene (GFRPP) bending bars have many advantages, such as high toughness, high durability, repeated molding and recycling, which can be used in concrete structures to replace steel stirrup for solving the problems of corrosion and service life. However, the changes in the properties of GFRPP bending bars during long-term use in alkaline concrete environments require further investigation. In the present study, GFRPP bending bars were immersed in alkaline solution at 20 °C, 40 °C, and 60 °C for as long as 180 d. The water absorption, hydrolysis, mechanical properties, and microscopic properties of the bending bars were evaluated to understand the long-term performance and mechanism of degradation. The bending bars had a higher saturated water absorption percentage and time along with a lower diffusion rate than the straight bars due to the presence of pores and micro-cracks formed during the bending process. The dissolution of the glass fibers in alkaline solution led to the partial mass loss of the GFRPP bars. Compared to the control, the tensile strength retention of the bending bars was 20.6%–56.0 %. The tensile failure mode changed from fiber bursting before immersion to shear fracture after immersion due to the decreased interfacial bonding strength and increased glass fiber brittleness. The primary degradation mechanisms were the etching of glass fibers, interface debonding, and increased void volume (∼23.7 %). The bending bars were more seriously eroded than the straight bars due to the twisting of the fibers and imperfect interfaces. The predicted degradation times of the GFRPP bending bars ranged from 1.7 years (Haikou) to 3.9 years (Harbin), corresponding to a stable tensile strength retention of 22.13 %. The results provide a basis for evaluating the durability and service life of GFRPP bending bars and promote the application of GFRPP composite stirrups in concrete structures.

Continuous-waves generation induced by laser radiation dynamics in transparent medium with passively mode-locked saturable absorber

Continuous-waves generation induced by laser radiation dynamics in transparent medium with passively mode-locked saturable absorber

Accurate measurement of the frequency offset of the laser based on electromagnetically induced transparency

We propose a method using electromagnetically induced transparency (EIT) to measure the frequency offset of the laser relative to a cavity’s resonance frequency, thereby reducing the laser detuning when preparing Rydberg atoms. Laser reflection by the vapor cell enables observation of two EIT peaks corresponding to the co-propagating and counter-propagating beams, and the peaks’ position is related to laser detuning, allowing us to estimate the frequency offset of the probe and coupling lasers. The method reduces the measurement uncertainty compared to directly observing saturated absorption spectroscopy (SAS) and EIT, making it suitable for applications that require strict control over laser detuning.

2D Materials‐Based Pulsed Solid‐State Laser: Status and Prospect

AbstractPulsed solid‐state lasers comprise 2D materials as saturable absorbers that contain transparent windows of the atmosphere and characteristic fingerprint spectra of several vital molecules that are significant in various applications and research. Over the past few decades, significant progress has been made in the development of narrow pulse width, high energy, high average output power, high efficiency, and simple construction of passively Q‐switched and mode‐locked lasers with 2D materials as saturable absorbers. This review summarizes the development of 2D materials, including graphene, transition metal dichalcogenides, black phosphorus, topological insulators, and MXenes, as modulator devices for solid‐state lasers owing to their broadband operation, excellent nonlinear optical response, low recovery time, ultrafast dynamic processing, and easy fabrication. Then, some new emerging and representative applications of pulsed solid‐state lasers are introduced and illustrated such as laser surgery, material processing, and lidar. Finally, future challenges and perspectives of pulsed solid‐state lasers with 2D materials‐based saturable absorbers are analyzed and addressed. The rapid development of pulsed solid‐state lasers with the continuous improvement of modulation technology is expected to expand opportunities for application in industry, scientific, medical, and other areas.

A high-performance passively Q-switched Tm:YAP laser with a TaSe2 saturable absorber

In this paper, TaSe2 material was prepared and used as a saturable absorber (SA) to modulate a Tm:YAP laser. Under the continuous-wave mode, an 18.31 W diode laser was used to pump the Tm:YAP crystal, and an output power of 6.22 W was achieved at 1993.1 nm with an optical–optical conversion efficiency of 33.9%. Under the passively Q-switched mode, the Tm:YAP pulse laser was modulated by a TaSe2-based SA, and a 2.8 W average power and a 440 ns pulse width at 73.15 kHz were obtained at 1988.4 nm, corresponding to an optical–optical conversion efficiency of 15.2% and a per pulse energy of 38.2 µJ.

Gamma alumina as a saturable absorbing material for C- and L-band ultrafast mode-locked fiber lasers

This work demonstrates femtosecond pulse generations in C- and L-band regimes utilizing a gamma-aluminum oxide/polydimethylsiloxane saturable absorber (γ-Al2O3/PDMS-SA) via mode-locking technique. The γ-Al2O3/PDMS-SA has a 7.3% modulation depth and a moderate saturation intensity of 303 MW/cm2, and estimated damage threshold of greater than 8.49 and 3.57 GW/cm2 pumping intensities in C- and L-band wavelengths, respectively. In the C-band laser cavity, the generated mode-locked pulse delivered a low threshold of 28.7 mW and an ultrafast width of 622 fs. Meanwhile, a higher threshold of 108.6 mW and 942 fs pulse width were measured in the L-band laser cavity centered at 1611 nm. These demonstrations showcase a versatile feature of γ-Al2O3 as a light-absorbing material that generates ultrashort pulses in a wideband wavelength range, which could benefit future research on the metastable state of aluminum-based materials within the field of ultrafast photonics.

Unveiling the enhanced optical limiting of polyaniline – Fullerene composite investigated by z-scan

The reverse saturable absorption (RSA) and optical limiting (OL) mechanisms of polyaniline (PANI) and fullerene doped PANI (PANI-C60) solutions were investigated by open-aperture z-scan studies, using a nanosecond pulsed Nd:YAG laser operating at 532 nm wavelength as the excitation source. The nonlinear absorption coefficient (β), OL threshold, and imaginary part of nonlinear susceptibility (χi(3)) of PANI and PANI-C60 solutions were determined for three different laser input pulse energies and are found to be in the order of 10−9 cm/W, 106 W/cm2, and 10−10 esu respectively. The results showed enhanced OL efficiency for the PANI-C60 solution, making it a promising candidate for applications in optoelectronics and optical limiting. The transmission electron microscope (TEM) images revealed the uniform distribution of C60 of particle size in the range of 5–10 nm in the PANI matrix. The composite formation of PANI-C60 was confirmed by Fourier transform infrared spectroscopy (FTIR). The presence of C60 and its charge transfer complex (CTC) formation with PANI are responsible for the enhanced OL efficiency. The linear refractive index values were measured using UV–Visible absorption spectra and compared with the theoretical values. The investigation of the OL mechanism and the calculation of its associated NLO parameters for PANI and PANI-C60 solutions are reported for the first time.

Enhanced interfacial, mechanical, and anti-hygrothermal properties of carbon fiber/cyanate ester composites with the catalytic sizing agents of titanium epoxy

The mechanical properties of composites are closely related to the interfacial behavior, especially under the hygrothermal circumstance. A catalytic sizing agent of titanium epoxy is designed to enhance interfacial, mechanical, and anti-hygrothermal properties of high modulus carbon fiber (HMCF)/cyanate ester composites simultaneously. The mechanisms of interface enhancement and low hygroscopicity of composites are investigated. The titanium epoxy is synthesized and its catalytic effect on the curing of cyanate ester is proved. The interfacial properties of HMCF composites with catalytic sizing agents are improved to 95.5 MPa, which is attributed to the interphase with high crosslinking density and sufficient triazine rings and oxazolidinone structure due to preferential curing induced by interfacial catalysis, stimulating the smooth transition of interphase modulus. Further, the formed interphase exhibits few interface defects and low content of hydroxyl groups, which changes the moisture diffusion path and reduces saturated water absorption of composites to only 0.36 %, resulting in the release of interfacial wet stress concentration and high retention of mechanical properties in hygrothermal environment. The resultant composites with high stiffness, excellent temperature resistance, superior dimensional stability and low moisture absorption are expected to be applied to high-orbit space, aerospace, precision instruments.