Sandstone Oil Reservoirs Research Articles

Experimental Investigation on Temperature-Resistant CO2 Foam Flooding in a Heterogenous Reservoir

Gas channeling treatment is a huge challenge for oil displacement and CO2 sequestration in the practical CO2 flooding process. The foaming agents can be used in the gas flooding process, which presents good application potential for gas channeling blockage. However, high temperature can affect surfactant foaming properties. This work takes a high-temperature heterogenous sandstone oil reservoir as an example; the foaming performance of different surfactants was evaluated via foamability, thermal stability, crude oil tolerance ability, and dynamic blocking capacity. The profile control performance of the optimized foaming agent was investigated via dual-core gas flooding experiments. (1) The results show that QPJ-c featured good foaming stability, which made it present the largest foam comprehensive index, although its foaming volume was slightly lower than that of QPJ-b. Its foaming volume retention rate was 83.2%, and its half-life retention rate remained 88.9% after 30 days aging at a temperature of 110 °C. (2) The foam resistance factor increased from 7 to 17 when the core permeability increased from 2 mD to 20 mD. This indicated that the high-permeability zone could be preferentially blocked by foam during the foam injection. (3) The dual-core flooding experiments verified that the fractional flow of the high-permeability core severely decreased due to the blockage of foam. The incremental oil recovery of the low-permeability core was 27.1% when the permeability ratio was 5. It increased to 40% when the permeability ratio was increased to 10. (4) Our work indicates that temperature-resistant CO2 foam could be a good candidate for profile control during CO2 flooding in the target reservoir.

The Saturation Calculation of NMR Logging Based on Constructing Water Spectrum Function

Tight sandstone oil reservoirs are characterized by complex structures, poor pore connectivity, and strong heterogeneity, with features such as low porosity and ultra-low permeability. Conventional methods for calculating saturation cannot accurately evaluate the hydrocarbon saturation of these reservoirs. To address this, a study was conducted from the perspective of non-electrical logging methods, focusing on the inherent nuclear magnetic resonance (NMR) characteristics of different fluids to develop a saturation calculation method that avoids the influence of the rock matrix, thus enabling precise saturation measurement in tight sandstone oil reservoirs. The traditional NMR porosity model was modified by segmenting it using the clay-bound water cutoff value, aiming to identify the distribution pattern of fluids in pores outside the clay-bound water zone. Through theoretical derivation and water spectrum function simulation, a water spectrum function and its parameter range suitable for the NMR T2 distribution in tight sandstone reservoirs were determined. Using core-sealed core saturation as a reference, the particle swarm optimization (PSO) algorithm was applied to optimize the parameter range and construct the final water spectrum function tailored to tight sandstone oil reservoirs. The accuracy and practicality of this method were validated by applying the derived water spectrum function to NMR logging in the exploration block, allowing for precise saturation calculations and the accurate evaluation of tight reservoir saturation.

Study on characteristics, efficiency, and variations of water flooding in different stages for low permeability oil sandstone

AbstractWater flooding is an important way to improve recovery in low‐permeability sandstone oil reservoirs. How to decouple the water flooding process using dynamic and static information is a hot topic. In this paper, taking the Paleocene low‐permeability oil sandstone, BY area, eastern Nanxiang Basin as an example, the microscopic water flooding process in the low‐permeability sandstone matrix was systematically investigated, and the characteristics of water channeling under the conditions of fracture existence were analyzed using the dynamic and static monitoring data. The results show that the target layer mainly develops frequently thin stacked composite sand bodies. Under the combined influence of matrix and fracture seepage, the low‐permeability sandstone developed by water flooding shows that there is a single direction of efficiency. The direction of advantageous water advancement is 45° north–east, and the speed of water flooding advancement is 2.57 m/day. Microscopic water‐drive oil experiments show that bound water is mainly distributed in the original low‐permeability sandstone as a membrane in the pore wall and as short rods in the throat. Differences in pore structure and petrophysical properties affect the residual oil content and degree of oil recovery. For sandstones with good petrophysical properties, mild water flooding can improve crude oil recovery. The increase in oil production is mainly concentrated in the early stage of water flooding development, and the increase in oil recovery degree is not significant with the increase in injection multiples in the middle and late stages. However, for sandstones with relatively poor petrophysical properties, water flooding is more effective in the early and late stages than in the middle stages. Therefore, it is necessary to adjust the water flooding measures according to the differences in the petrophysical properties of the sand body. Local tectonics and natural fracture strikes are important factors affecting the direction of the expansion of water flooding fractures. Overall, the prevention of water channeling in low‐permeability sandstones has to take into account the complex coupling between water flooding fractures, natural fractures, and hydraulic fractures.

A comprehensive study of the enhanced oil recovery potential of low-salinity water in heavy oil sandstone reservoir

To determine the enhanced oil recovery potential of low-salinity brine for a heavy oil sandstone reservoir, a holistic approach including both experimental and theoretical studies was employed in this study. Macro-scale forced and spontaneous imbibition tests were performed to quantify the oil recovery potential by our considered three brines. Furthermore, micro-scale experiments, including FTIR (Fourier-Transform Infrared Spectroscopy), TGA (Thermogravimetric Analysis) and zeta potential, were executed to explore the micro-scale oil-brine-rock interactions (i.e., polar component desorption from the rock surface) that has controlled the macro-scale oil recovery efficiency. In addition, to further investigate the underlying physical mechanism that leads to the discrepancy in polar component desorption when subjected to different brines, charge-distribution multi-site complexation model (CD-MUSIC) and DLVO-based disjoining pressure calculation were performed to describe the molecular-level electrokinetic interactions at the oil-brine and rock-brine interfaces, as well as the total interaction force between these two interfaces. Our results show that the oil recovery efficiency of the low-salinity aquifer water (LSAW) was markedly higher than produced water (PW) and seawater (SW) from the forced and spontaneous imbibition tests. Combined with the marginal difference on interfacial tension (IFT) results, it guided us to conclude that the micro-scale oil-brine-rock interaction controlled the macro-scale oil recovery performance. FTIR and TGA experimental results on pristine quartz, oil aged quartz, as well as different water treated aged quartz powders revealed that the polar component desorption efficiency in different brines followed the order of LSAW > PW > SW, which was consistent with the macro-scale oil recovery trend. The total disjoining pressure result gave rise to the conclusion that the most repulsive disjoining pressure in LSAW leads to the most efficient desorption of polar oil component from the rock surface. In addition, the electrokinetic properties of the oil/brine and rock/brine interfaces, as well as the consequent electrical double layer force play a crucial role in differentiating the oil-brine-rock interactions in different brines. This study has shed light on the further application of low-salinity aquifer water in our target heavy oil reservoir.

Enhanced oil recovery and mitigating challenges in sandstone oil reservoirs employing EDTA chelating agent/ seawater flooding

While low salinity water (LSW) holds promise for improving oil recovery, its implementation is comparatively costly due to the substantial volumes of fresh water required to dilute seawater (SW). Additionally, concerns arise regarding potential issues related to LSW, including fines migration in sandstone reservoirs and scale formation in carbonate reservoirs. Chelating agents can be introduced into undiluted SW to bind with metal ions, thereby lowering its salinity. This approach mimics the behavior of LSW injection while overcoming associated challenges. This study involves measuring oil/injected solution interfacial tension (IFT), evaluating sandstone surface wettability alteration, along with conducting different sand pack flooding scenarios using Ethylenediaminetetraacetic acid (EDTA) chelating agent. The aim was to comprehend the EDTA oil recovery mechanisms and determine the optimal concentration of EDTA that minimizes chemical consumption while maximizing oil recovery. The findings indicated that incorporating 5 wt% EDTA into SW significantly reduced IFT from 29.52 mN/m to 4.75 mN/m, making the oil nearly miscible in the solution. Moreover, wettability tests confirmed that a minimum EDTA concentration of 5 wt% is required to shift wettability from oil-wet to strongly water-wet conditions. Sand pack flooding experiments, on the other hand, further demonstrated that this optimized fluid system can potentially recover an additional 16.1 % of oil following SW flooding. Finally, inductively coupled plasma (ICP) analysis revealed a notable increase in metal ion concentration during EDTA flooding, indicating enhanced leaching of metals from the sandstone surface and improved wettability characteristics.

Study on the Occurrence Characteristics of the Remaining Oil in Sandstone Reservoirs with Different Permeability after Polymer Flooding.

After polymer flooding, the heterogeneity between different layers intensifies, forming intricate seepage channels and fluid diversions, which results in decreased circulation efficiency and lower recovery rates, leaving a significant amount of residual oil trapped within the reservoir. Understanding the characteristics of residual oil occurrence is crucial for enhancing oil recovery post-polymer flooding. This study focused on sandstone reservoirs with varying permeability in the Saertu block of the Daqing oilfield. Using cryosectioning and laser scanning confocal microscopy, the occurrence characteristics of the residual oil in these sandstone reservoirs post-polymer flooding were investigated. Additionally, micro-CT and scanning electron microscopy were employed to analyze the impact of the pore structure on the distribution characteristics of the residual oil. The results indicate that laser scanning confocal images reveal that post-polymer flooding, the residual oil in high- and low-permeability sandstone reservoirs predominantly exists in a bound state (average > 47%), mostly as particle-adsorbed oil. In contrast, the residual oil in medium-permeability reservoirs is primarily in a free state (average > 49%), mostly as intergranular-adsorbed oil. In high-permeability sandstone reservoirs, heavy oil components are mainly in a particle-adsorbed form; in medium-permeability sandstone reservoirs, residual oil predominantly consists of heavy components, with most light components occurring in a clustered form; in low-permeability sandstone reservoirs, clustered residual oil exists in a balanced coexistence of light and heavy components, while the heavy components primarily exist in a particle-adsorbed form. Post-polymer flooding, the large pore-throat structure in high-permeability sandstone reservoirs results in effective displacement and less free residual oil; medium-permeability sandstone reservoirs, with medium-large pores and throats, have preferential channels and fine particles blocking the throats, leading to some unswept pores and more free residual oil; low-permeability sandstone reservoirs, with small pores and throats, exhibit weak displacement forces and poor mobility, resulting in more bound residual oil. The distribution and content of clay particles and clay minerals, along with the complex microscopic pore structure, are the main factors causing the differences in the residual oil occurrence states in sandstones with varying permeability.

Application of Low-Salinity Waterflooding in Heavy Oil Sandstone Reservoir: Oil Recovery Efficiency and Mechanistic Study.

Low-salinity water injection (LSWI) is a recently emerged and promising technique to enhance oil recovery. In addition, it is attractive due to its relatively low-cost, environmental friendliness, and sustainability. However, the underlying mechanisms remain unclear, and very limited research has been conducted on heavy oil. To verify the feasibility of injecting a low-salinity aquifer water (LSAW) to improve the oil recovery of our target offshore heavy oil reservoir, first, a series of experiments on the core scale, including coreflooding and spontaneous imbibition experiments, were carried out. Furthermore, atomic force microscopy (AFM), contact angle, zeta potential measurement, as well as disjoining pressure calculations based on the Derjaguin-Landau-Verwey-Overbeek (DLVO) theory were carried out to explore the underlying governing mechanism at the microscopic scale. The secondary oil recovery factors of the coreflood tests are 67.11, 70.55, and 77.18% for seawater (SW), produced water (PW), and LSAW, respectively. The additional oil recoveries by LSAW when injected in tertiary modes are 6.38% after SW injection and 5.68% after PW injection. These results indicate that compared with SW and PW which have high brine salinity, the low-salinity brine from the subsurface aquifer (LSAW) can improve oil recovery in both secondary and tertiary modes. In addition, the oil recovery factors from the spontaneous imbibition tests (27.52% by LSAW, 17.32% by PW, and 14.00% by SW) and the insignificant variation of IFTs among the three brines lead to the anticipation that the LSAW can alter the rock to a more water-wet condition compared with SW and PW, thereby giving rise to a higher oil recovery factor in the coreflooding tests. By using AFM imaging and contact angle tests, we proved that the polar asphaltene could desorb from the rock surface and consequently reduce the water contact angle substantially when subjected to low-salinity brine. Furthermore, the zeta potential and the disjoining pressure results indicate that a more repulsive force was developed between oil and the rock under the low-salinity environment, which thereby promotes asphaltene desorption and consequent wettability alteration. Our work has paved the way to apply LSWI to the offshore heavy oil sandstone reservoir.

Smart Water–Polymer Hybrid Flooding in Heavy Oil Sandstone Reservoirs: A Detailed Review and Guidelines for Future Applications

Smart Water–Polymer Hybrid Flooding in Heavy Oil Sandstone Reservoirs: A Detailed Review and Guidelines for Future Applications

Accumulation mechanism of multi-type unconventional oil and gas reservoirs in Northern China: Taking Hari Sag of the Yin’e Basin as an example

Abstract Many multi-types of unconventional oil and gas reservoirs have been found in some faulted basins in northern China, showing good exploration potential. However, the hydrocarbon accumulation mechanism in these areas is still unclear, which limits the understanding of the distribution of oil and gas. In this study, we took Hari Sag in Yin’e Basin as an example, conducted a systematic analysis on various types unconventional oil and gas reservoirs, and revealed its characteristics and accumulation mechanisms. The study showed that there were many types of unconventional oil and gas reservoirs in Hari Sag, such as biogas reservoirs, shale gas reservoirs, shale oil reservoirs, tight sandstone oil reservoirs, tight sandstone gas reservoirs, and volcanic gas reservoirs. These reservoirs generally had characteristics of “near/within source rocks accumulation,” “coexistence of oil reservoirs and gas reservoirs,” “shallow oil and deep gas,” and so on. Research on the mechanism of hydrocarbon accumulation showed that: the lack of effective hydrocarbon migration pathway was the main reason for “near/within source rocks accumulation” of oil and gas reservoirs; the differences in the thermal evolution degree of the main source rocks at different structural positions in the sag made the distribution characteristics of hydrocarbon as “coexistence of oil reservoirs and gas reservoirs” and “shallow oil and deep gas”; and the joint development of multi-type effective unconventional reservoirs created the situation of “coexistence of multi-type unconventional oil and gas reservoirs.” It is predicted that six types of unconventional oil and gas reservoirs have a cumulative area of 381 km2, indicating that the Hari Sag has great potential for unconventional oil and gas exploration. The research results can not only guide the unconventional oil and gas exploration in Hari Sag but also provide a theoretical basis for exploration research in similar blocks.

Investigation of Asphaltene Precipitation and Reservoir Damage during CO2 Flooding in High-Pressure, High-Temperature Sandstone Oil Reservoirs

Summary Asphaltenes are heavy aromatic hydrocarbon compounds contained in reservoir fluids and may precipitate when the reservoir pressure is reduced by production or when gas is injected into the reservoir, and then further deposit on pore-throat surfaces causing reservoir damage. At present, the research on asphaltene precipitation and reservoir damage is carried out in conventional reservoirs, and the influence of CO2 injection under high-pressure, high-temperature (HPHT) conditions has not yet been clearly understood. In this work, we combined perturbed-chain statistical association fluid theory (PC-SAFT) calculation, experiments, phase-state simulation, and numerical simulation to predict the asphaltene precipitation with different pressures, temperatures, and amounts of injected gas and to clarify the influence on reservoir permeability and oil production when using CO2 injection. The results show that the precipitation of asphaltenes in the process of CO2 injection is the desorption of colloid-asphaltene inclusions caused by gas molecules and then the mutual polymerization process between dispersed asphaltene molecules. CO2 injection will increase the amount of precipitation and move the precipitation curve to the right side. The degree of permeability reduction caused by the deposition of asphaltenes in the core is 12.87–37.54%; the deposition of asphaltenes in the reservoir is mainly around the injection/production wells and along the injected gas profile. Considering asphaltenes, the oil recovery degree is reduced by 1.5%, and the injection rate is reduced by 17%. The reservoir pressure, temperature, and physical properties have a strong correlation with the degree of reservoir damage, while the initial asphaltene content has a low correlation. This work will be of great interest to operators seeking to enhance oil recovery by CO2 injection in deep reservoirs.

Analyzing the Microscopic Production Characteristics of CO2 Flooding after Water Flooding in Tight Oil Sandstone Reservoirs Utilizing NMR and Microscopic Visualization Apparatus

The microscopic pore structure of tight sandstone reservoirs significantly influences the characteristics of CO2 flooding after water flooding. This research was conducted using various techniques such as casting thin sections, high-pressure mercury injection, scanning electron microscopy, nuclear magnetic resonance (NMR) testing, and a self-designed high-temperature and high-pressure microscopic visualization displacement system. Three types of cores with different pore structures were selected for the flooding experiments and the microscopic visualization displacement experiments, including CO2 immiscible flooding, near-miscible flooding, and miscible flooding after conventional water flooding. The characteristics of CO2 flooding and the residual oil distribution after water flooding were quantitatively analyzed and evaluated. The results show the following: (1) During the water flooding process, the oil produced from type I and type III samples mainly comes from large and some medium pores. Oil utilization of all pores is significant for type II samples. The physical properties and pore types have a greater impact on water flooding. Type I and II samples are more suitable for near-miscible flooding after water flooding. Type III samples are more suitable for miscible flooding after water flooding. (2) In CO2 flooding, oil recovery increases gradually with increasing pressure for all three types of samples. Type II core samples have the highest recovery. Before miscibility, the oil recovered from type I and type II samples is primarily from large pores; however, oil recovery mainly comes from medium pores when reaching miscibility. As for the type III samples, the oil produced in the immiscible state mainly comes from large and medium pores, and the enhanced oil recovery mainly comes from medium and small pores after reaching the near-miscible phase. (3) It can be seen from the microscopic residual oil distribution that oil recovery will increase as the petrophysical properties of the rock model improve. The oil recovery rate of near-miscible flooding after water flooding using the type II model is up to 68.11%. The oil recovery of miscible flooding after water flooding with the type III model is the highest at 74.57%. With increasing pressure, the proportion of flake residual oil gradually decreases, while the proportion of droplet-like and film-like residual oil gradually increases. Type II samples have a relatively large percentage of reticulated residual oil in the near-miscible stage.

An NMR-based model for determining irreducible water saturation in carbonate gas reservoirs

Unambiguously determining irreducible water saturation Swirr\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\left({S}_{\\rm{wirr}}\\right)$$\\end{document} poses a formidable challenge, given the availability of multiple independent methods. Traditional approaches often depend on semi-experimental relationships derived from simplified assumptions. These methods, originally designed for oil sandstone reservoirs, result in varying Swirr\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{{\ ext{wirr}}}$$\\end{document} values when employed in carbonate gas reservoirs. Nuclear magnetic resonance (NMR) is the most advanced technique for determining Swirr\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{{\ ext{wirr}}}$$\\end{document}. While highly accurate, the NMR-based method necessitates the laboratory measurement of the transverse relaxation time T2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\left({T}_{2}\\right)$$\\end{document} cutoff. Laboratory-based T2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${T}_{2}$$\\end{document} cutoff determination is resource-intensive and time-consuming. This research aims to develop a robust model for determining Swirr\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{{\ ext{wirr}}}$$\\end{document} in carbonate gas reservoirs by utilizing NMR well logging measurements and special core analysis (SCAL) tests. Various T2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${T}_{2}$$\\end{document} cutoff values were initially employed to compute bound water saturation Sbw\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\left({S}_{{\ ext{bw}}}\\right)$$\\end{document} at different depths to achieve this. Subsequently, the data points T2,Sbw\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\left({T}_{2}, {S}_{{\ ext{bw}}}\\right)$$\\end{document} were graphed on a scatter plot to unveil the relationship between Sbw\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{{\ ext{bw}}}$$\\end{document} and T2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${T}_{2}$$\\end{document}. The scatter plot illustrates an exponential decrease in Sbw\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{bw}$$\\end{document} with increasing T2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${T}_{2}$$\\end{document}, forming the basis for the Swirr\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{{\ ext{wirr}}}$$\\end{document} model derived from this relationship. Finally, the parameters of the Swirr\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{{\ ext{wirr}}}$$\\end{document} model were fine-tuned using SCAL tests. Notably, this Swirr\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{{\ ext{wirr}}}$$\\end{document} model not only accurately yields Swirr\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${S}_{{\ ext{wirr}}}$$\\end{document} at each depth but also offers a dependable determination of the optimal T2\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${T}_{2}$$\\end{document} cutoff for the reservoir interval.

Prediction of Oil Production in a Tight Sandstone Reservoir: Triassic Chang 9 Member, Jiyuan Area, Ordos Basin, NW China

Tight sandstone oil reservoirs in the Upper Triassic Yanchang Formation of the Ordos Basin are the most promising exploration and development fields owing to their huge production potential. Even though they have received considerable attention in recent years, common productivity prediction methods were not well applied during pre-development owing to their strong internal heterogeneity. In this study, the factors influencing oil production of the Chang 9 Member in the Jiyuan area were investigated and summarized based on drill cores, such as sediment characteristic analysis, lithofacies analysis, other analytical tests, and conventional logging curves. The findings show that fine-sandstone reservoirs with smooth sand body architectures are the main types of tight sandstone commercial oil reservoirs. Furthermore, having high porosity and oil content are prerequisites for commercial oil reservoirs, and the cumulative thickness of effective reservoirs serves as a crucial resource base for them. Through the analysis of logging curves, the relative center of gravity, deviation root of variance, petrophysical index, effective reservoir thickness, and evaluation indicator were used to predict daily oil production, thereby establishing the identification criteria for the ranking of tight sandstone oil reservoirs using logging. Then, the productivity of each reservoir in a single well was predicted by processing the log data from each well using the proposed method, and the productivity prediction results agreed well with the tested results of the perforated interval. This approach highlights the integrated influence of geological factors, physical properties, and the thickness scale of an effective reservoir, thereby improving the predictive capacity of logging curves. Additionally, the proposed methods significantly reduce the need for reservoir parameters better than previous ones, streamline operations, and improve practical applications.

Enhanced oil recovery by using modified ZnO nanocomposites in sandstone oil reservoirs

Recently, nanocomposites were employed to improve the extraction of oil in different reservoirs. Due to the unique characteristics of nanoparticles such as small size, efficient altering main mechanisms such as IFT, CA, and viscosity reduction, have received wide attention among researchers. This study investigated the application of a newly designed ZnO-cerium N-composite for EOR at reservoir conditions, and the performance was compared to the standalone ZnO nanoparticles. After performing the morphology of the N-composite, the effect of the N-composites on the wettability alteration, interfacial tension, viscosity, Zeta potential, pH, and density was studied at different N-composites concentrations at reservoir conditions. Based on the results of rock/fluid interactions at the static phase, an optimum concentration was chosen for performing dynamic core flooding experiments. At 100 ppm, the highest stability and the highest reduction in capillary force were observed. The presence of Ce in the structure of the N-composite changes the pore volume of ZnO-Ce compared to ZnO nanoparticles, which affects the surface charge. IFT (mN/m), CA (°), and zeta potential (mV) were (22.51, 40.83, and − 44.36), and (30.50, 50.21, and − 31.05) for ZnO-Ce and ZnO, respectively at 100 ppm. By application of the optimized nanofluid in an oil displacement study, RF in the presence of ZnO-Ce, and ZnO were 37.11% and 71.40%, respectively.

Fractures in faulted sandstone reservoir

The Chang 8 Member of the Yanchang Formation in southwest Ordos Basin is a typical faulted sandstone oil reservoir. The development characteristics of fractures have obvious controlling effect on the formation of sweet spots of tight reservoir. In this paper, taking the Chang 8 Member of the southwestern Ordos Basin as an example, the development characteristics and controlling factors of fractures in faulted sandstone oil reservoir are systematically studied. The results show that the faulted sandstone oil reservoirs in the study area are distributed along the main strike-slip faults. The fracture system includes vertical fractures and horizontal bedding fractures. The fracture surface of vertical fractures generally has good oil display, and mostly presented as oil spot and oil immersion level; however, the oil level of horizontal bedding fractures is usually presented as oil spot level. The development frequency of horizontal bedding fractures is 62.5 %, while that of vertical fractures is 37.5 %. The fractures are mainly developed in fine sandstone and a small amount of medium-grained sandstone and siltstone. The factors that affect the fracture development degree in faulted oil reservoir include the distance from main fault, sand thickness, lithology and structural location. For the Jinghe and Honghe Oilfields, the degree of fracture development decreases sharply when the distance from the main fault is greater than 1.25 km and 1.5 km, respectively. Single sand body thickness also controls the degree of fracture development. Single sand bodies with thickness within 6 m have more developed fractures, and the fracture development decreases sharply when the thickness exceeds 6 m. The sand body in the wing part of river channel is relatively thin with fine grain size and small compacted space, which is easy to break under tectonic activity. The fractures of the Chang 8 Member in the study area are mainly developed near the faults, the top of anticline and its wing part.

The Influence of Micro-Heterogeneity on Water Injection Development in Low-Permeability Sandstone Oil Reservoirs

Micro-heterogeneity in low-permeability sandstone oil reservoirs significantly influences the uniformity of water injection during development. This leads to the formation of preferred channels for water injection, causing premature water breakthroughs in oil wells. Not only does this reduce oil displacement efficiency, but it also enriches residual oil in the formation, which ultimately impacts the overall recovery rate. This study employed various methods, including thin-section casting, qualitative analysis through scanning electron microscopy, quantitative analysis of X-ray diffraction, high-pressure mercury intrusion and particle size, and experimental techniques, such as wettability and micro-displacement, to investigate the impact mechanism of micro-heterogeneity on water injection development in low-permeability oil reservoirs. A typical low-permeability sandstone oil reservoir in the Ordos Basin was used as a case study. The results reveal that the reservoir’s micro-heterogeneity is determined by the heterogeneity of the interstitial material, porosity, and particle size. Micro-heterogeneity plays a critical role in the flow characteristics and oil displacement efficiency of low-permeability oil reservoirs. The less the micro-heterogeneity, the better the water injection development outcome. This study suggests a technical policy adjustment method that is critical for guiding the development of low-permeability water injection oil reservoirs, thereby improving the effectiveness of water injection development.

Concise extraction and characterization of the pore-throat network in unconventional hydrocarbon reservoirs: A new perspective

In this study, a new image-based method for the extraction and characterization of pore-throat network for unconventional hydrocarbon storage and exploitation is proposed. “Pore-throat solidity”, which is analogous to particle solidity, and a new method for automatic identification of pores and throats in tight sandstone oil reservoirs are introduced. Additionally, the “pore-throat combination” and “pure pore” are defined and distinguished by drawing the cumulative probability curve of the pore-throat solidity and by selecting an appropriate cutoff point. When the discrete grid set is recognized as a pore-throat combination, Legendre ellipse fitting and minimum Feret diameter are used. When the pore and throat grid sets are identified as pure pores, the pore diameter can be directly calculated. Using the new method, the analytical results for the physical parameters and pore radius agree well with most prior studies. The results comparing the maximum ball and the new model could also prove the accuracy of the latter's in micro and nano scales. The new model provides a more practical theoretical basis and a new calculation method for the rapid and accurate evaluation of the complex processes of oil migration.

Formation damage induced by working fluids sequentially interacting with tight sandstone oil reservoirs

Drilling fluid loss is a frequent downhole incident in the process of deep well drilling and completion. Drilling fluid will damage the formation permeability and affect well production, but some wells with high volume drilling fluids loss can have high production. To investigate the mechanism of drilling fluid loss damage in tight sandstone oil reservoirs, this study selects some core plugs and the working fluids from X field in Ordos Basin, China, conducts the evaluation experiments of drilling fluid damage and working fluid sequential contact damage, and analyzes the well history and well production performance data. Results show that the permeability recovery rate decreases continuously, after different fluid displacement. The permeability recovery rate of rock sample after drilling fluid displacement is 46.21–67.14%, and the permeability recovery rate after different working fluid displacement is 22.92–61.45%. Then well history and production fluctuations are analyzed. It shows the incompatibility of working fluid will cause superimposed damage to hydraulic fractures. The main damage mechanism caused by drilling fluid loss is incompatibility damage and particle invasion. Loss of drilling fluid will improve damage risk of the subsequent stimulation operations, though it doesn't show damage features in initial stage. Formation damage degree is related to the storage space type of reservoir. The results serve as a guide for the drilling fluid design of oil in tight sandstone formation.

Effects of Pore Water Content on Stress Sensitivity of Tight Sandstone Oil Reservoirs: A Study of the Mahu Block (Xinjiang Province, China)

Traditional stress sensitivity experiments are typically conducted under dry conditions, without considering the reservoir’s water content. In reality, the presence of water within pores significantly influences the extent of stress sensitivity damage in tight sandstone oil formations, subsequently affecting the determination of stress sensitivity coefficients during experimentation. By investigating sandstone samples from wells in the Mahu Block of China’s Xinjiang province, we observed that increasing water saturation reduces the stress sensitivity of tight sandstone. By conducting stress sensitivity experiments under varying water content conditions, we found that the stress sensitivity coefficient is not a constant value but decreases as water saturation increases. Based on experimental comparisons, an optimized power-law model for stress-sensitive damage assessment was refined. By conducting stress-sensitive damage assessment experiments under different water content conditions and integrating the concept of comprehensive compression coefficient, an improved stress-sensitive power-law model was established allowing for the influence of water content. The accuracy of this improved model was increased by 46.98% compared to the original power-law model through experimental validation. The research outcomes can enhance the accuracy of permeability and productivity evaluation, providing valuable guidance for unconventional oil and gas development.

Enhanced Oil Recovery from Heavy Oil Sandstone Reservoirs Using DTPA Chelating Agent/SW Solution

Enhanced Oil Recovery from Heavy Oil Sandstone Reservoirs Using DTPA Chelating Agent/SW Solution