Sample Surface Research Articles

The effect of oxidation on tribology behavior of nickel-graphite coated stainless steel SS420

The main solution to the challenge of maintaining maximum sealing in the compressor section of each gas turbine is the use of abradable coatings. These coatings have a double duty, including (a) maintaining the lagging and (b) protecting the tips of the rotor blades. Choosing the type of abradable coating primarily depends on the service temperature of the coating. Nickel-graphite (Ni-G) coating is a good choice for use up to 480 °C and, or steel/sub-alloy rotor blades. In this research, the Ni-G coating was applied by the flame spraying method of Ni-G powder with a thickness of about 250 μm on an SS420 stainless steel substrate. The effect of the composition of the bonding layer was also investigated using two compositions, Ni-5Al and NiCrAlY. Obtaining the knowledge of applying Ni-G coating by flame spraying, identifying the structural and compositional characteristics of the coating (through optical and electron metallography), and the effect that oxidation can have on the tribological behavior of the coating were among the goals of this project. The best conditions for spraying the Ni-G coating were achieved an oxygen gas pressure of 6 bar, oxygen flow rate of 18 L min−1, acetylene pressure of 1.5 bar, acetylene flow rate of 24 L min−1, and the distance between the gun head and the sample surface was 22 cm. The results showed that placing the coating in oxidizing conditions increases its coefficient of friction. The increase in the coefficient of friction was attributed to the formation of oxide shells on the surface of the coating after 500 h of exposure to oxidation conditions. Corresponding to the higher coefficient of friction, the oxidized coating showed a decrease in wear resistance as a result of oxidation. This result can show the decrease in abradable of this coating with increasing service time.

Angle-dependent ion-beam etching of RuAl thin films for structuring GHz-frequency electronics

Abstract The ruthenium aluminide (RuAl) alloy is a promising electrode material for wireless surface acoustic wave sensors working under harsh conditions at high temperatures. However, during the structuring of RuAl thin films using ion-beam etching, etched material can redeposit at the edges of the electrodes and form objects, so-called fences, on top of the structured features. These decrease the high-temperature stability and lead to an undesired alteration of the sensor performance. In this work, the angle-dependent ion-beam etching of RuAl thin-films was investigated to inhibit the formation of such fence structures. The etch rate was determined as a function of the etching angle between ion-beam and sample surface in a range between 90° and 40°.
Furthermore, finger structures with pitches below 500 nm, which are required for devices working in the intended GHz regime, were patterned to study the influence of the etching angle on the profile of the RuAl electrode fingers using transmission electron microscopy and energy-dispersive X-ray spectroscopy. The results show that an etching angle of 50° results in the highest etch rate. For etching angles of 50° and below, the width of the fences is reduced below 10 nm, so they break off during standard resist removal procedures. Such low etching angles lead to shadowed areas on the side of structured features, in which unetched material remains. However, this material can be removed by using a two-step etching process combining a 50° step with a 90° step. This process is capable of structuring fence-free trapezoidal-shaped electrode finger profiles. Therefore, the developed process is well suited for the fabrication of high-temperature GHz-frequency RuAl electrodes.

Detection of SARS-CoV-2 on the environmental surfaces and its implications for pandemic preparedness

Even though death due to COVID-19 is no longer a public health emergency, less virulent but highly transmissible forms of SARS-CoV-2 continue to spread in many countries leading to outbreaks and rise in hospitalizations in the affected regions. Lessons learned during the pandemic must be put into action to protect the world's population from another catastrophe like COVID-19. Novel approaches that were developed for tracking the spread of SARS-CoV-2 included analysis of wastewater, air samples, and various environmental surfaces. We conducted a study in Kuwait during the peak of COVID-19 pandemic to examine if SARS-CoV-2 could be detected in swabs taken from frequently touched environmental surfaces. We selected 12 Cooperative Society Stores—two from each governorate of Kuwait—for collection of surface samples. The Cooperative Society Stores are widely distributed across the whole country and cater to daily household needs including groceries and other essential items. These stores operated even during the “lockdown” imposed at the height of the pandemic. We collected swabs from high-touch surfaces including the handles of the shopping carts and freezers, the elevators, the keypads of the point-of-service terminals of cash counters, and the automated teller machines. All the surfaces tested showed a variable presence of SARS-CoV-2 by reverse transcriptase quantitative PCR, showing the validity of the proof-of-concept study. Monitoring of the presence of SARS-CoV-2 by surface sampling thus offers a cheap but effective means of environmental surveillance for coronaviruses. We therefore strongly recommend the addition of surface environmental sampling as a strategy for pandemic preparedness everywhere.

Mechanical and Microstructural Characterization of AISI 316L Stainless Steel Superficially Modified by Solid Nitriding Technique

AISI 316L austenitic stainless steel superficially modified by the solid nitriding technique was investigated at different nitriding times (2, 4, 6, 8, 12 and 24 h) and at 450 °C. The microstructural characterization was conducted using scanning electron microscopy (SEM) analysis and X-ray diffraction analyses, finding the presence of Fe2–3N, Fe4N and Cr2N, among others. The mechanical behavior of the modified surfaces was carried out by developing hardness profiles and relating it with the nitride layer thickness evaluated using scanning electron microscopy (SEM), obtaining layers up to 70 µm wide. The nitrogen diffusion produced species above and below the surface sample with a transformation from the austenitic phase to an expanded austenite (γN) phase, which is responsible for producing an increase in hardness of up to 1200 HV in the samples treated at 24 h, which is four times higher than the untreated steels. Wear evaluations of the obtained layers were performed using a pin-on-disk system under zero lubrication, indicating that the samples with 12 and 24 h of treatment present the best wear resistance promoted by an oxidative–adhesive mechanism. The obtained results are positively comparable with those of the ion nitriding technique but with a lower implementation cost.

Assessment of Soil Physico-chemical Properties in Sugarcane Cultivation Areas of Navsari District, Gujarat, India

Sentinel 2 satellite data from the year 2021 were acquired from the Copernicus site to identify the sugarcane producing area in the Navsari district. Hybrid classification approach i.e., supervised and unsupervised with ground truth data were applied using ERDAS IMAGINE software. After image classification, 2.5 km x 2.5 km grid was prepared in Q-GIS software which along with classified sugarcane area were overlapped for site identification. Then, random soil surface and sub-surface samples were collected with reference from grid of intensive sugarcane growing area. The particle density (2.10 to 2.76 g cm-3 with the mean value of 2.58 g cm-3) and bulk density (1.10 to 1.68 g cm-3 with the mean value of 1.33 g cm-3) of surface soil were found to be lower than sub-surface soil (2.18 to 2.79 g cm-3 and 1.15 to 1.68 g cm-3 with the mean value of 2.62 g cm-3 and 1.42 g cm-3 respectively) while porosity (31.60 to 59.26% with the mean value of 48.39%) and maximum water holding capacity (22.77 to 51.92% with the mean value of 39.60%) of surface soil were found to be higher than sub-surface soil (29.54 to 57.71% and 20.98 to 48.91% with the mean value of 45.60% and 36.81% respectively). The pH of soil surface showed range from 6.08 to 8.37 while pH of soil sub-surface noted range of 6.00 to 8.50. The electrical conductivity of surface and sub-surface soil showed the range of 0.011 to 1.580 dS m-1 and 0.010 to 1.586 dS m-1. The soil organic carbon of surface soil ranged from 0.06 to 0.89% while that of sub-surface soil varied from 0.02 to 0.85%.

Small scale pool fires: The case of toluene

Industrial applications adopting toluene as a solvent have been largely extended in recent years, including solutions within the framework of the energy transition and energy storage technologies. The potential use of this flammable compound in a different set of operative conditions and compositions requires a comprehensive and complete knowledge of its fire behaviour and combustion kinetic. To this scope, an innovative experimental procedure applicable to liquid reactive systems was developed for this scope and implemented at different boundary conditions. More specifically, the specimen was exposed to air and heat fluxes between 7 and 50 kW/m2, at a constant sample surface of 0.01 m2, an initial sample thickness of 0.01 m, and a distance between the sample and the horizontally oriented conical-shaped heater of 0.025 m. Measurements were compared with data from the current literature, when available, demonstrating the robustness and validity of the adopted procedure. Although an increase in the external flux leads to growing mass burning rates (i.e., from 0.47 g/s to 0.85 g/s), negligible effects on the ignitability were observed. Conversely, a peak in the heat release rate at 35 kW/m2 was measured. The observed reduction at higher external heat fluxes was attributed to less effective combustion, demonstrating that the maximum expected heat flux cannot be considered as an aprioristic worst-case scenario for the evaluation of pool fires. The collected data were, then, further utilized to obtain insights on the formation of the main products, including soot tendency. Based on the collected data a simplified kinetic model suitable for the computational fluid dynamics was proposed to reproduce the chemistry of the system.

Development of a magnetic separation method for rapid isolation and enrichment of bacteria in raw pork using chitosan functionalized magnetic Fe3O4@MIL-100(Fe) composites.

In this study, a pretreatment method based on a magnetic capture probe for the rapid isolation and enrichment of bacteria from raw pork was developed. The chitosan immobilized Fe3O4@MIL-100(Fe) was prepared as a capture probe for total bacterial counts through the electrostatic interaction of positively charged chitosan and the negatively charged substances on the surface of bacteria. The interference of matrix in pork samples on this method was studied and removed by differential centrifugation. The results showed the capture probe had a great selectivity binding and magnetic separation properties for the tested six common bacteria in pork. Under the optimal conditions, the capture efficiency of the bacteria (105 CFU mL-1) from pork surface samples was all above 90%. The capture efficiency of the bacteria in a homogenate system was greatly decreased due to the interference of sarcoplasmic protein and myofibrillar protein in pork. The matrix effect was mitigated by a differential centrifugation method, and the capture efficiency of all six bacteria was >80%. The developed magnetic separation method took 40min and showed good isolation and enrichment properties of bacteria. Thus, the proposed method is expected to provide a simple, convenient, and time-saving pretreatment method for the detection of total bacterial counts in pork.

Theoretical Calculations and Experimental Study of the Nitrided Layer of 1Cr17Ni2 Steel

Due to the harsh operating conditions experienced by 1Cr17Ni2 steel, efforts were made to optimize its performance by subjecting 1Cr17Ni2 stainless steel to nitriding treatments at temperatures of 460 °C, 500 °C, and 550 °C, each for durations of 8 and 16 h. The formation state of its cross section was observed through a metallurgical microscope and scanning electron microscope, and it was characterized by hardness measurement. Through a ball-on-disk wear experiment, the adhesive wear and friction coefficient of its non-lubricated sliding were measured. The phase composition of its surface was measured by XRD. The results revealed that nitriding led to the formation of a modified layer on the surface of the samples, with a depth of 130 μm after nitriding at 550 °C for 16 h. The hardness of the modified layer exceeded that of the matrix, reaching up to 1400 Hv0.1. X-ray diffraction (XRD) analysis of the sample surfaces indicated the presence of high-hardness phases such as CrN, γ′-Fe4N, and ε-Fe2-3N. This article predicts the mechanical properties of nitrided phases in high-alloy martensitic stainless steel through first-principles computational methods. We provide a reference for improving the performance of high-alloy steel after nitriding through a combination of theoretical calculations and experiments.

Spatiotemporal Analysis of Secondary Metabolites Produced by S.coelicolor Using Automated Sampling Mass Spectrometry

Natural products (NPs) are organic compounds that are synthesized by living organisms such as bacteria. NPs and their derivatives are very useful in the medical field to develop new drugs, particularly new antibiotics which are crucial to combat developing antibiotic resistance. The current research on the secondary metabolites (SMs) produced throughout the growth cycle of bacteria is limited, as the standard procedure is to examine the SM production at the end of the bacteria’s growth cycle. Therefore, there may be many undiscovered SMs which are produced and consumed prior to analysis. A mass spectrometer (MS) can be used to track analytes of interest, such as SMs. When the MS is paired with an ambient ionization technique like the Liquid Micro-Junction Surface Sampling Probe (LMJ-SSP) it works as a minimally invasive approach to track the SMs in real time produced throughout the bacterial growth cycle. This allows for the SMs to be tracked both temporally and spatially without killing the bacteria. The process is automated using the LMJ-SSP mounted to a 3D printer, allowing for a grid-like sampling process to map NPs production. Herein, A 3D-printed growth chamber dubbed the “Washing And Sampling Agar Bacterial Inoculation” (WASABI) Box was designed to resemble a sampling grid for simpler analysis. Another key feature of the WASABI Box are washing ports, containing 70% ethanol, to sterilize the LMJ-SSP and minimize contamination between rows. The SM production of S. coelicolor in the WASABI Box was analyzed from day 4 to 7 of the bacterial growth cycle, where the data was used to generate spatial-temporal heat maps tracking metabolites including Albaflavenone (m/z 219.2), Desferrioxamine B (m/z 561.4), Germicidin B (m/z 183.1), Kalafungin (m/z 301.1), and Streptorubin B (m/z 392.3).

Annealing Time Dependence on Creation of SiV, GeV, and SnV in Diamond by Atmospheric Annealing at 1800 °C

The creation of SiV−, GeV−, and SnV− are presented by the atmospheric annealing in the argon flow. Compared to high‐pressure annealing, in which gas cannot flow, atmospheric annealing with an inert gas flow not only causes less degradation of the sample surface but also has the advantage of reducing equipment cost and preparation time. Excessive annealing time has been shown to reduce the amount of centers created. The optimal annealing time that maximizes formations depends on the type of diamond sample and the implanted ions. Furthermore, inspired by the split‐vacancy structure of the group IV–V centers, atmospheric pre‐annealing at 600 °C to increase the amount of di‐vacancy is demonstrated, followed by annealing at 1800 °C for 1 min. A shorter duration of high‐temperature annealing is expected to qualitatively reduce stress and deterioration of the crystallinity of the diamond sample.

Investigating Flow-Induced Corrosion of Magnesium in Ophthalmological Milieu.

Although the impact of local fluid dynamics in the biodegradation of magnesium is well known, currently no studies in the literature address the degradation effects of ocular vitreous on bioresorbable devices made of magnesium, which could be developed as drug delivery carriers. The aim of this study was to investigate the flow-induced corrosion mechanism of magnesium in an ophthalmological environment for future applications in ophthalmic drug delivery. To achieve this, experimental and computational methods were combined. Specifically, a CFD model was employed to design experimental conditions that replicate the ocular flow-induced shear stress (FISS) on manufactured magnesium samples. Pure Mg samples were tested in a bioreactor system capable of imposing the ocular CFD calculated values of FISS on the Mg samples' surface by varying the pump flow rate. Optimal flow rates for a range of different FISS values specific to the ophthalmological fluid dynamics affecting the device were indeed determined before running the experiments. After conducting customized corrosion tests, morphological observations and profilometric maps of the eroded surfaces of Mg samples were obtained using scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM). These maps were then post-processed for the parametric evaluation of corrosion rates. Pre-existing localized superficial defects did affect the final corrosion pattern. SEM images and CLSM data confirmed a uniform corrosion mechanism, with corrosion rates of 1.9, 2.7, and 3.4 μm/day under different shear stress conditions (0, 0.01, and 0.032 Pa, respectively). More generally, uniform corrosion on pure Mg samples increased with higher FISS values, and at higher shear stress values (FISS = 0.032 Pa), a notable washing-out effect of the corrosion products was observed. The removal of corrosion products at higher shear stresses suggests that the dynamic ocular environment, influenced by saccadic movements, plays a significant role in the corrosion mechanism of pure magnesium. The corrosion rates determined in this study, in conjunction with clinical drug release requirements, are crucial for designing potential drug-release devices for ocular applications.

Investigation of mechanical and wettability properties of commercial pure titanium by surface mechanical attrition treatment

The examination of mechanical and wettability properties of commercial pure titanium (CP-Ti) introduced a novel challenge. The microstructure of samples was analyzed by using OM and SEM micro-images. In this study, the hardness of the surface and cross section of samples was evaluated, and the effect of several surface mechanical attrition treatments (SMATed) on samples was examined. Also, the tensile test was done to compare the effect of SMAT duration on mechanical properties of samples. The contact angle method was then employed to investigate the impact of SAMT duration on the wettability trend. According to results, as the treatment time increases, twins become evident in the deeper layers of the samples. In contrast, the near-surface twins are shorter than those found in the deeper material, signifying the presence of finer grains. Moreover, the elevated hardness in SMATed samples can be attributed to several key factors, including cold work, a rise in defects and twins, and grain refinement. The surface hardness increases across the sample series (up to Ti6) due to the substantial energy input. Nevertheless, it is anticipated that further continuation of the process will result in a constant surface hardness. The increased strength observed in SMATed samples can be attributed to factors such as reduction in grain size and the formation of twins. The wettability results show that the treated surfaces exhibited a significant change in wettability compared to the untreated samples, with a 25% reduction in the contact angle. This is attributed to the surface modifications induced by the treatment process, which introduced more hydrophilic functional groups. The results also show that after 4 h of treatment, the contact angle increases, suggesting that the trend may plateau with additional treatment time.

Experimental study of wear and rolling contact fatigue in railway wheel steels coupled with various brake block materials: Insights from innovative small-scale testing

This study presents a comprehensive analysis using an innovative testing method of two wheel steels paired with cast iron and organic composite brake block materials. By conducting tests under consistent conditions and varying in duration, the study examines temperature profiles, friction coefficients, surface characteristics, weight loss, and microstructural changes in wheel samples, emphasizing the distinct behaviour of these materials in braking applications and the damage evolution over time. The results demonstrate that organic composite brake samples outperform those in cast iron, showcasing smoother wheel sample surfaces and stable friction coefficients. Weight loss analysis reveals the environmental benefits of organic composite brakes, emitting fewer particulates than cast iron counterparts. Microstructural examinations uncover the formation of a Thermal White Etching Layer (T-WEL) on wheel samples tested with cast iron samples, leading to cracks and material detachment. Conversely, extended use of organic composite samples led to a "thermal fuse effect", impacting their efficiency and suggesting the need of careful temperature management in sustained braking scenarios. Despite significant differences in wheel steels, the study underscores the critical role of brake material in braking improvements. The findings not only enhance the scientific understanding of brake material behaviour but also introduce an innovative, cost-effective, and fast 4-contact machine testing method.

Spotting ignition of plastic foam by a fast-moving hot metal particle

Spotting ignition involves dynamic interaction between fuel bed and hot particles, but the scientific understanding of the ignition by a fast-moving hot particle is still limited. Herein, a hot steel particle with various horizontal velocities, temperatures, and sizes is shot to ignite vertically oriented low-density expandable polystyrene foam. A high-speed particle can directly get embedded into the foam to achieve flash-point, fire-point, or no ignition, while a low-speed particle bounces away from the foam without ignition. Results show that for a particle of 1150 °C, its minimum velocity for embedding is 12.00 m/s. Such a critical velocity for hot-particle embedded or ignition slightly decreases as particle temperature increases. Minimum ignition temperature of these high-speed particles is 200 °C higher than that of near-static or with a low free-fall velocity, due to the shorter residence time and insufficient to produce a flammable mixture. Moreover, when the particle is neither too slow to bounce away nor too fast to get embedded, it will be partially embedded on the sample surface to burnout the fuel, posing the biggest fire hazard. It deepens our knowledge of the complex interaction between hot moving particles and insulation foam to reduce spotting fire risk for building façade.

The Seasonal Characterization and Temporal Evolution of Nitrogen, Phosphorus and Potassium in the Surface and Groundwater of an Agricultural Hydrographic Basin in the Midwestern Brazilian Savanna

The Brazilian savanna (Cerrado Biome) is one of the most important regions in the world in terms of food production, with the use of fertilizers based on nitrogen, phosphorus and potassium (NPK). When not applied properly, fertilizers can alter and affect water quality. The objective of this study was to evaluate the presence of these compounds in surface and groundwater in the Upper Jardim River Hydrographic Unit, Federal District, thus characterizing seasonal variations during the dry and rainy seasons in two periods. A total of 207 groundwater samples and 23 surface water samples were collected in the years 2014, 2015, 2019 and 2020. The parameters analyzed were pH and nitrate, nitrite, ammonium, phosphate and potassium ions. In groundwater samples, pH values were significantly higher and ion levels lower in samples collected during the early years (except for nitrate), and the ammonium concentrations were lower in the dry season than the rainy (in 2014 and 2019). In surface samples, total phosphorus levels were significantly higher in the rainy/2019 compared to the rainy/2020 season, while this tendency was inverted for potassium during the dry season. The use of NPK-based fertilizers has increased considerably in recent years in the region due to the expansion of the agricultural area, and although the results of the study show that concentrations in water are much lower than the maximum values allowed by Brazilian legislation, continuous monitoring is necessary to guarantee water quality.

Novel hybrid interference and atomic force microscopy

Abstract A novel hybrid microscope which combines an interference microscopic (IM) and an atomic force microscopic (AFM) measurement mode is introduced. It is realised by adding an AFM probe to an IM, where the AFM probe can be mechanically switched in or out of the beam path of the IM. When the AFM cantilever is out of the beam path, the system works in the IM measurement mode for noncontact and fast optical measurements. When the AFM cantilever is in the beam path, it works in the AFM measurement mode, where the AFM tip interacts with sample surfaces for measurements. The deformation of the AFM cantilever induced by the tip-sample interaction force is detected from interference fringes, which are formed by the interference of the light beam reflected from the backside of the AFM cantilever and a reference beam in the IM. This novel design has a high-level synergy of AFM and IM technologies and provides several promising application potentials. For instance, it can bring high-resolution AFM measurements whenever and wherever needed in IM measurements, thus, to complement the lateral resolution limits of IM; The AFM measurement mode can provide measurement results with higher topography fidelity, thus, to offer in-situ reference areal surface metrology for IM measurements. In the paper, design concept, realisation of a prototype instrument, and experimental results illustrating the performance of the prototype instrument are detailed. 

Electric field enhanced diffusion welding of alloy 617: Microstructural characteristics and mechanical properties

This study investigated the microstructural characteristics and mechanical behavior of diffusion welded nickel-based Alloy 617 obtained by electric field-assisted sintering (EFAS) using various parameters. The interfacial microstructure exhibited different characteristics including good grain boundary (GB) migration across the interface in the samples diffusion-welded at 1100 °C and a flat interface in the samples joined at 1000 °C and 1050 °C. The interface consisted of fine Al2O3 oxides, while precipitation of interfacial M23C6 carbides was not observed. Grain boundaries migrated across the Al2O3 oxides, leaving these oxides within the grains. Graded grain size was observed, with grain coarsening being more significant near the sample surface due to the temperature gradient induced by EFAS. Tensile testing revealed that the specimens fractured in the matrix away from the interface, indicting strong diffusion-welded joints. The peak tensile strength of 807 MPa was obtained in the samples welded at 1000 °C due to minimal grain growth. The materials obtained at 1100 °C exhibited reduced tensile strength but improved ductility. Strain maps revealed by digital image correlation showed alternating high and low strain segments in the samples produced at 1000 °C and 1050 °C, indicating that the flat interfaces with no GB migration were less ductile compared to the matrix. A greater strain uniformity was observed along the bond interfaces with improved GB migration. The hardness reduced near the sample surfaces due to enlarged grains induced by temperature gradient. This study demonstrates that GB migration and enhanced mechanical strength can be achieved in diffusion-welded Alloy 617.

Environmental bacterial load during surgical and ultrasound procedures in a Swedish small animal hospital

BackgroundEnvironmental bacteria in animal healthcare facilities may constitute a risk for healthcare-associated infections (HAI). Knowledge of the bacterial microflora composition and factors influencing the environmental bacterial load can support tailored interventions to lower the risk for HAI. The aims of this study were to: (1) quantify and identify environmental bacteria in one operating room (OR) and one ultrasound room (UR) in a small animal hospital, (2) compare the bacterial load to threshold values suggested for use in human healthcare facilities, (3) characterise the genetic relationship between selected bacterial species to assess clonal dissemination, and (4) investigate factors associated with bacterial load during surgery.Settle plates were used for passive air sampling and dip slides for surface sampling. Bacteria were identified by Matrix Assisted Laser Desorption—Time Of Flight. Antimicrobial susceptibility was determined by broth microdilution. Single nucleotide polymorphism-analysis was performed to identify genetically related isolates. Linear regression was performed to analyse associations between observed explanatory factors and bacterial load.ResultsThe bacterial load on settle plates and dip slides were low both in the OR and the UR, most of the samples were below threshold values suggested for use in human healthcare facilities. All settle plates sampled during surgery were below the threshold values suggested for use in human clean surgical procedures.Staphylococcus spp. and Micrococcus spp. were the dominating species. There was no indication of clonal relationship among the sequenced isolates. Bacteria carrying genes conveying resistance to disinfectants were revealed.Air change and compliance with hygiene routines were sufficient in the OR. No other factors possibly associated with the bacterial load were identified.ConclusionsThis study presents a generally low bacterial load in the studied OR and UR, indicating a low risk of transmission of infectious agents from the clinical environment. The results show that it is possible to achieve bacterial loads below threshold values suggested for use in human healthcare facilities in ORs in small animal hospitals and thus posing a reduced risk of HAI. Bacteria carrying genes conveying resistance to disinfectants indicates that resistant bacteria can persist in the clinical environment, with increased risk for HAI.

Oxidation kinetics of Ti6Al4V alloy deposited by wire arc additive manufacturing using argon gas as processing atmosphere

Ti6Al4V alloy is currently the most common metal alloy of the α+β phase type, its application is increasing as it has excellent properties at elevated temperatures. The main users of Ti6Al4V alloy are industries like of aerospace, naval, and biomedical; therefore, Ti6Al4V alloys one of the most studied material worldwide. One of the great advantages that Ti6Al4V alloy offers is the possibility of manufacturing components in situ by means of additive technologies.. Similar studies, in additive manufacturing, have reported the formation of titanium oxide on the surface of the material, followed by an oxygen-enriched region called "α-case". By means of thermogravimetric analysis, the oxidation effect on the surface of Ti6Al4V samples, obtained by wire arc additive manufacturing as well as samples from conventional manufacture, were studied. Argon gas, with an oxygen partial pressure of 1x10-5 atm, was used as the oxidation atmosphere within a range of 550°C to 950°C and oxidatión times of 60 min and 180 min. For the oxidation reaction, the kinetic analyses led to calculate the activation energy as 250 kJ/mol and 166 kJ/mol for the Ti6Al4V alloy processed by conventinal and additive manufacturing, respectively. The results of the of thermogravimetric analysis were fitted to a parabolic-type kinetic model. Furthemore, a mathematical model was proposed to predict the oxidation kinetics. The experimental data were fitted to the mathematical model in the range of 750 - 950°C for Ti6Al4V alloy by wire arc additive manufacturing. The oxidized microstructures were analized by optical and electronic microscopy finding α-case on the surface of the samples.

Decarbonization of siderite in the water-rich upper mantle

The aqueous fluids within subducted slabs have the potential to influence the form of carbonate presence and the carbon cycling process. Experiments were performed on resistive heating diamond anvil cell using siderite crystals and grains with water under conditions of pressure as high as 11.4 GPa and temperatures reaching up to 530 °C. These experiments aimed to simulate geological reactions that may occur within a depth range of 340 km in subducted slabs. Raman spectroscopy was employed to monitor the reactions and microscale phenomena within the sample chamber as pressure and temperature increase. The recovered products were analyzed using scanning electron microscopy and transmission electron microscopy. The results indicate that at 0.8 GPa and 108°C, a Fischer-Tropsch Type (FTT) reaction occurred on the sample surface, resulting in the formation of organic compound formaldehyde, followed by the observation of formic acid. At higher pressures and temperatures (3.5 GPa, 420°C), the formation of γ-Fe2O3 and γ-FeOOH was observed on the sample surface, accompanied by the release of CO2 and H2. Transmission electron microscope analysis of the quenched product powders indicated that the generated iron oxides were consistent with the phases observed at high pressure and temperature conditions. High pressure and temperature dissolution experiments of siderite in water reveal that carbon may be released into the mantle wedge entirely in the form of CO2 in warm subducted slabs and cold subducted slabs that subduct to depths of 75 km. The released CO2 participates in the carbon cycle of the island arc volcanic systems in the upper mantle at depths of 70–120 km and accelerates the transfer of subducted carbon to the Earth’s surface.