Rod Assembly Research Articles

Numerical Investigation on Transverse Flow of Helical Cruciform Fuel Rod Assembly in a Lead-Bismuth Cooled Fast Reactor

Numerical Investigation on Transverse Flow of Helical Cruciform Fuel Rod Assembly in a Lead-Bismuth Cooled Fast Reactor

Controlling the Emission Properties of Quantum Rods via Multiscale 3D Ordered Organization

A specific organization of optically active nanoscale objects can greatly affect the optical response of a system. Here, we report the controlled modification of the fluorescent emission by the assembly of water-soluble quantum rods (QRs). Our study combines optical, electron microcopy, and X-ray scattering characterizations to reveal a correlation between the self-assembly behavior of QRs into ordered 3D-arrays and the optical properties (luminescence) of formed assemblies, where the observed optical response is highly dependent on the QR aspect ratio. Specifically, shorter, 18 nm long QRs (QR18), exhibiting a well-defined smectic packing, demonstrate an enhancement of the emission intensity accompanied by a red shift and a lifetime reduction. In contrast, 40 nm long QRs (QR40), forming a columnar phase, does not show these optical properties.

Formation of Cytoplasmic Actin-Cofilin Rods is Triggered by Metabolic Stress and Changes in Cellular pH

Actin dynamics plays a crucial role in regulating essential cell functions and thereby is largely responsible to a considerable extent for cellular energy consumption. Certain pathological conditions in humans, like neurological disorders such as Alzheimer’s disease or amyotrophic lateral sclerosis (ALS) as well as variants of nemaline myopathy are associated with cytoskeletal abnormalities, so-called actin-cofilin rods. Actin-cofilin rods are aggregates consisting mainly of actin and cofilin, which are formed as a result of cellular stress and thereby help to ensure the survival of cells under unfavorable conditions. We have used Dictyostelium discoideum, an established model system for cytoskeletal research to study formation and principles of cytoplasmic actin rod assembly in response to energy depletion. Experimentally, depletion of ATP was provoked by addition of either sodium azide, dinitrophenol, or 2-deoxy-glucose, and the formation of rod assembly was recorded by live-cell imaging. Furthermore, we show that hyperosmotic shock induces actin-cofilin rods, and that a drop in the intracellular pH accompanies this condition. Our data reveal that acidification of the cytoplasm can induce the formation of actin-cofilin rods to varying degrees and suggest that a local reduction in cellular pH may be a cause for the formation of cytoplasmic rods. We hypothesize that local phase separation mechanistically triggers the assembly of actin-cofilin rods and thereby influences the material properties of actin structures.

Functional state of the brain bioelectric activity in treatment of diaphyseal lesions of the radius using the transosseous osteosynthesis of the wire and rod arrangement

Radial fracture is the most common trauma to the musculoskeletal system and accounts for 50 % of traumatic injuries to the bones of the upper limb. Disability in patients with fractures of the forearm bones ranges from 6 to 8 months, so the choice of the most effective method of treatment is very relevant. Currently, an important point is the tendency of optimizing the transosseous method by eliminating the disadvantages and looking for new advantages of external fixation. Bone fracture and associated surgical intervention are always accompanied by varying degrees of changes in the links of the central nervous system, hemodynamics and metabolism. In order to study the bioelectrical activity of the brain in 47 patients with a fracture of the radial diaphysis treated in the Traumatology Department of the Irkutsk Scientific Centre of Surgery and Traumatology, in the pre- and postoperative period we compared EEG indicators of two variants of the layout of the external fixation apparatus (EF): wire and rod. Analysis of the rhythms of bioelectrical activity of the brain in both groups in the preoperative period revealed a normal zonal distribution with the dominance of the alpha rhythm on the EEG, which generally reflects a rather high degree of organization of neuroactivity and indicates the stability of cerebral homeostasis. At the same time, in the group of patients with a wire-mounted EF device in the postoperative period, EEG indices significantly differed from the values of the norm and ndicators in the group with a rod-shaped arrangement. A decrease in the amplitude of alpha and beta rhythms was noted, as well as a shift in the frequency of bioelectric activity towards slow waves, which is a sign characteristic of discirculatory encephalopathy. An EEG study using the method of transosseous osteosynthesis with EF devise of a rod assembly showed its greater efficiency compared to the use of an EF device of a wire assembly during treatment and rehabilitation. Thus, the study of the bioelectric activity of the brain is a reliable method for assessing its functional state after an injury, as well as the effectiveness of the treatment.

A non-linear symmetric [formula omitted]-conforming Bézier finite element formulation for the analysis of Kirchhoff beam assemblies

We present a formulation for slender space curved rods and rod assemblies that implicitly accounts for the Kirchhoff constraints and for the G1-continuity conditions (i.e. continuity of the geometric tangent) between elements. The whole formulation is developed in tensorial coordinate free form, apt to any numerical interpolation to be implemented. A symmetric tangent stiffness operator is obtained performing the second covariant derivative of the internal energy functional, for which the Levi-Civita connection of the configurations manifold of the rod is needed. The G1-continuity conditions are fulfilled by means of a change of basis, from the original configuration parameters (position of the beam axis and rotation around the axis tangent) to a new set of configuration parameters, whose relation to the original set is non-linear. For this reason an additional geometric term, specific for the G1-formulation, appears in the tangent stiffness matrix. The robustness and accuracy of the obtained Kirchhoff model is demonstrated with numerical examples that employ Bézier interpolation for the position and for the rotation angle.

BB0259 Encompasses a Peptidoglycan Lytic Enzyme Function for Proper Assembly of Periplasmic Flagella in Borrelia burgdorferi.

Assembly of the bacterial flagellar rod, hook, and filament requires penetration through the peptidoglycan (PG) sacculus and outer membrane. In most β- and γ-proteobacteria, the protein FlgJ has two functional domains that enable PG hydrolyzing activity to create pores, facilitating proper assembly of the flagellar rod. However, two distinct proteins performing the same functions as the dual-domain FlgJ are proposed in δ- and ε-proteobacteria as well as spirochetes. The Lyme disease spirochete Borrelia burgdorferi genome possesses a FlgJ and a PG lytic SLT enzyme protein homolog (BB0259). FlgJ in B. burgdorferi is crucial for flagellar hook and filament assembly but not for the proper rod assembly reported in other bacteria. However, BB0259 has never been characterized. Here, we use cryo-electron tomography to visualize periplasmic flagella in different bb0259 mutant strains and provide evidence that the E580 residue of BB0259 is essential for PG-hydrolyzing activity. Without the enzyme activity, the flagellar hook fails to penetrate through the pores in the cell wall to complete assembly of an intact periplasmic flagellum. Given that FlgJ and BB0259 interact with each other, they likely coordinate the penetration through the PG sacculus and assembly of a functional flagellum in B. burgdorferi and other spirochetes. Because of its role, we renamed BB0259 as flagellar-specific lytic transglycosylase or LTaseBb.

Mechanical Reliability Analysis of Control Rod Assembly for HTR-PM

The article analyzes the forces and weaknesses of the control rod assembly in the high temperature gas cooled reactor (HTGR) demonstration project-pebble bed modular HTGR plant (HTR-PM), using the the mechanical reliability theory and mechanical simulation, and identifies the weaknesses at the connection of the control rod assembly. In the reliability-life calculation method based on the probabilistic fracture mechanics, in combination with the influence of irradiation on the fatigue life model and in consideration of the stress, the authors establish the reliability-life model to calculate the reliability-life of HTR-PM control rod assembly at the irradiation attenuation coefficient of 0.7. The calculation results show that at the reliability level of 0.99, the life of HTR-PM control rod assembly is about 150,000 action cycles, and that the irradiation has a great influence on the life of the control rod assembly. In view of what mentioned above, this paper can provide reference for the equipment reliability management of the HTR-PM control rod assembly.

Coaxial Conjugated Polymer/Quantum Rod Assembly into Hybrid Nanowires with Preferred Quantum Rod Orientation

Coaxial Conjugated Polymer/Quantum Rod Assembly into Hybrid Nanowires with Preferred Quantum Rod Orientation

Void fraction distribution for convective boiling flows in single and multiple heater rods assembly

Void fraction distribution is an essential parameter for the design and development of nuclear reactors. In this work, void fraction measurements have been performed on an experimental setup mimicking the flow behavior in a calandria of Boiling Water Reactor (BWR). Experimental measurements for void fraction distribution were performed on three heater rods configurations at fixed electrical power using non-invasive gamma-ray densitometry at varying inlet liquid flow rates and temperatures. The main focus of this contribution was to measure void fraction distribution of boiling flows in a test section having the arrangement to accommodate different heater rods configurations by keeping the mechanical aspects of the gamma-ray densitometry technique simple. Measurements were done at four axial locations. and at each axial location, void fraction measurement was performed at eight radial locations. Experimental results show that void fraction profiles are not only influenced by the configuration of heater rods but also by the operating conditions. The void fraction profiles of configuration A were flat as compared to all other heater rod configurations. The data reported here help develop CFD models and understand the dependence of void fraction distribution on heater rods configuration.

White-Light-Emitting Supramolecular Polymer Gel Based on β-CD and NDI Host-Guest Inclusion Complex.

Supramolecular polymer formed by non-covalent interactions between complementary building blocks entraps solvents and develops supramolecular polymer gel. A supramolecular polymer gel was prepared by the heating-cooling cycle of β-cyclodextrin (β-CD) and naphthalenedimide (NDI) solution in N,N-dimethylformamide (DMF). The host-guest inclusion complex of β-CD and NDI 1 containing dodecyl amine forms the supramolecular polymer and gel in DMF. However, β-CD and NDI 2, having glutamic acid, fail to form the supramolecular polymer and gel under the same condition. X-ray crystallography shows that the alkyl chains of NDI 1 are complementary to the hydrophobic cavity of the two β-CD units. From rheology, the storage modulus was approximately 1.5 orders of magnitude larger than the loss modulus, which indicates the physical crosslink and elastic nature of the thermo-responsive gel. FE-SEM images of the supramolecular polymer gel exhibit flake-like morphology and a dense flake network. The flakes developed from the assembly of smaller rods. Photophysical studies show that the host-guest complex formation and gelation have significantly enhanced emission intensity with a new hump at 550 nm. Upon excitation by a 366 nm UV-light, NDI 1 and β-CD gel in DMF shows white light emission. The gel has the potential for the fabrication of organic electronic devices.

Modulation of the Enzymatic Activity of the Flagellar Lytic Transglycosylase SltF by Rod Components and the Scaffolding Protein FlgJ in Rhodobacter sphaeroides.

Macromolecular cell-envelope-spanning structures such as the bacterial flagellum must traverse the cell wall. Lytic transglycosylase enzymes are capable of enlarging gaps in the peptidoglycan meshwork to allow the efficient assembly of supramolecular complexes. In the periplasmic space, the assembly of the flagellar rod requires the scaffold protein FlgJ, which includes a muramidase domain in the canonical models Salmonella enterica and Escherichia coli. In contrast, in Rhodobacter sphaeroides, FlgJ and the dedicated flagellar lytic transglycosylase SltF are separate entities that interact in the periplasm. In this study, we show that sltF is expressed, along with the genes encoding the early components of the flagellar hierarchy that include the hook-basal body proteins, making SltF available during the rod assembly. Protein-protein interaction experiments demonstrated that SltF interacts with the rod proteins FliE, FlgB, FlgC, FlgF, and FlgG through its C-terminal region. A deletion analysis that divides the C terminus in two halves revealed that the interacting regions for most of the rod proteins are not redundant. Our results also show that the presence of the rod proteins FliE, FlgB, FlgC, and FlgF displace the previously reported SltF-FlgJ interaction. In addition, we observed modulation of the transglycosylase activity of SltF mediated by FlgB and FlgJ that could be relevant to coordinate rod assembly with cell wall remodeling. In summary, different mechanisms regulate the flagellar lytic transglycosylase, SltF, ensuring a timely transcription, a proper localization and a controlled enzymatic activity. IMPORTANCE Several mechanisms participate in the assembly of cell-envelope-spanning macromolecular structures. The sequential expression of substrates to be exported, selective export, and a specific order of incorporation are some of the mechanisms that stand out to drive an efficient assembly process. Here, we analyze how the structural rod proteins, the scaffold protein FlgJ and the flagellar lytic enzyme SltF, interact in an orderly fashion to assemble the flagellar rod into the periplasmic space. A complex arrangement of transient interactions directs a dedicated flagellar muramidase toward the flagellar rod. All of these interactions bring this protein to the proximity of the peptidoglycan wall while also modulating its enzymatic activity. This study suggests how a dynamic network of interactions participates in controlling SltF, a prominent component for flagellar formation.

Design and Fabrication of Solenoid Compressed Hybrid Air Engine

As we are moving towards the developed country, the need of fossil fuel is increasing day by day with increasing population. We need alternative to replace fossil fuel. In IC engine, the chemical energy get converted into mechanical energy, i.e., the low grade energy get converted into high grade energy. The IC engine we use cause more pollution. So to overcome this problem, the electromagnetic force and compressed air is use to run the engine. The solenoid compressed hybrid air engine which uses electric energy and compressed air to run, can replace the use of IC engine. As we pass current through the copper wire winding, the magnetic field generated near the copper wire. The polarity of the magnetic field can vary according to the current. The magnet attached at the piston get attracted up as the polarity of permanent magnet and this force is transferred to the connecting rod and crankshaft assembly, which transfer the reciprocating motion of piston into rotating motion of crankshaft and finally the flywheel. The electromagnetic engine should be more compatible. The electromagnetic engine does not require extra components like cam follower, valves, fuel pump, injectors, fuel tank etc. The strength of magnetic force can be increase by varying the input voltage and current.

Prediction of pressure drop in hexagonal wire-wrapped rod bundles using artificial neural network

In this study, an artificial neural network (ANN) model was utilized to predict the friction factor for wire-wrapped rod assemblies. The 80 experimental data sets from UCTD correlations (Chen et al., 2018) were used to train and validate the ANN models. Three ANN models were introduced for laminar, transition, and turbulence flow conditions, respectively. The flow regime was determined based on the Reynolds number and the pitch to diameter ratio. To estimate the friction factor, Reynolds number, and multiple design parameters such as the number of rods, the rod's diameter, the diameter of the wire, the lattice pitch, the edge pitch, and the wire's helical pitch were used from the 80 bundles dataset. Three-quarters of the total data was used for training, while the other quarter was used for validation. The Levenberg-Marquardt method with Gauss-Newton approximation for Hessian of the training cost function was applied for training. For validation of the models, the cross-validation method was adopted. The ANN models were composed of seven inputs, R1 neurons in the hidden layer, and a single-output (7-R1-1). The R1 was determined based on the minimum validation error principle. Training and validation were repeated 20 times using randomly shuffled data sets to estimate the ANN model's uncertainty and errors. The prediction of the trained models showed meaningfully low errors (0.00 % of Mean error, 6.59 % of standard deviation of error, 10.83 % of 90 % of confidence interval, and 6.58 % of Mean RMS of 80 bundles data) when they are compared with correlations suggested by previous studies (CTD, UCTD, CTS, UCTS, and REH).

Robustness and the evolution of length control strategies in the T3SS and flagellar hook

Bacterial cells construct many structures, such as the flagellar hook and the type III secretion system (T3SS) injectisome, that aid in crucial physiological processes such as locomotion and pathogenesis. Both of these structures involve long extracellular channels, and the length of these channels must be highly regulated in order for these structures to perform their intended functions. There are two leading models for how length control is achieved in the flagellar hook and T3SS needle: the substrate switching model, in which the length is controlled by assembly of an inner rod, and the ruler model, in which a molecular ruler controls the length. Although there is qualitative experimental evidence to support both models, comparatively little has been done to quantitatively characterize these mechanisms or make detailed predictions that could be used to unambiguously test these mechanisms experimentally. In this work, we constructed a mathematical model of length control based on the ruler mechanism and found that the predictions of this model are consistent with experimental data—not just for the scaling of the average length with the ruler protein length, but also for the variance. Interestingly, we found that the ruler mechanism allows for the evolution of needles with large average lengths without the concomitant large increase in variance that occurs in the substrate switching mechanism. In addition to making further predictions that can be tested experimentally, these findings shed new light on the trade-offs that may have led to the evolution of different length control mechanisms in different bacterial species.

RANS simulations for transition and turbulent flow regimes in wire-wrapped rod bundles

Internal flows through rod assemblies are commonly found in heat exchangers, steam generators, and nuclear reactors. One of the fuel assembly designs considered for liquid metal-cooled reactors utilizes wires helically wrapped around each fuel rod as spacers. The wires keep the fuel pins separated, enhancing the turbulent mixing, and heat transfer, but also affecting the pressure drop. It is of interest the understanding of the fluid flow phenomena in the sodium-cooled fast reactor as it is one of the Generation IV advanced reactor designs and it has been a motivating topic of research for the last decade. A wire-wrapped fuel assembly replica with 61-pins has been in operation at the Thermal-Hydraulic Research Laboratory of Texas A&M University. This facility produced high-fidelity velocity and pressure drop data for validation of computational fluid dynamics codes. This study investigates the effects of geometrical features and operating conditions on the flow behavior of the 61-pin wire wrapped bundle using Reynolds-Averaged Navier-Stokes (RANS) models to predict the axial and transverse pressure drops for a range of Reynolds numbers from 1,270 to 100,000. The friction factor predictions were in satisfactory agreement with the experimental data and the Upgraded Chen and Todreas correlation. The internal subchannel velocity results were compared with experimental data and Large Eddy Simulations (LES) and found in reasonable agreement. This study demonstrates that RANS is a suitable approach in predicting velocity and pressure fields in wire-wrapped rod bundles, with a relatively low computational effort.

Trip turbine transient and stability analysis of two different fuel assembly designs aimed for the recycling of minor actinides and plutonium in BWRs

Recycling in thermal reactors is an alternative that could help to reduce minor actinide inventories produced by depleted fuel assemblies of nuclear reactors; the current paper assesses two proposed BWR fuel assemblies to recycle MA. These fuel designs aim to no introduce any perturbation in the electricity production from the Boiling Water Reactor, and they must satisfy the reactor core safety constraints. Such constraints must be considered under steady and transient conditions without the need to make any modification to the nuclear reactor safety systems. Previously, these two fuel designs were assessed under steady state conditions. In this study, the two proposed fuel assembly designs are tested for stability analysis and trip turbine transitory conditions. These fuel assembly designs are based on a 10 × 10 standard fuel assembly, and they have four MA-bearing rods that are replacing four fuel rod assemblies in three of the six axial fuel cells that compose the fuel assembly. The first design is a UO2 fuel assembly; the second one is a MOX fuel assembly where also, 8 fuel pin rods have been replaced by water rods in three of the six axial fuel cells that compose the fuel assembly. These two proposed fuel assemblies have been designed to be equivalent by producing the same amount of energy of the BWR reactor. The stability analysis is performed considering a global reactor oscillation; results show that in the MOX fuel assembly, the control rod pattern must be modified to provide an acceptable shutdown margin and to have adequate stability conditions. Both fuel designs provide acceptable conditions under the trip turbine transient condition and provide two fuel assembly designs that could be used for MA recycling in a BWR without any perturbation in energy production.

ГИДРОДИНАМИКА ТУРБУЛЕНТНЫХ ПОТОКОВ В ТВС БЫСТРЫХ РЕАКТОРОВ (ПОЛЕ СКОРОСТИ И МИКРОСТРУКТУРА ТУРБУЛЕНТНОСТИ)

The article describes the factors under the influence of which the formation of thermohydraulic characteristics occurs in the fuel assemblies of the core of fast reactors with liquid metal cooling. It is shown that one of the most important factors is a complex multiply connected geometry of a stochastic nature, subject to deformation during the campaign under the influence of temperature irregularities and radiation effects. The paper presents and analyzes the results of experimental and computational studies of the velocity field and shear stress, the microstructure of turbulence, momentum transfer in the central and peripheral regions of fuel assemblies without and with displacers, as well as in the case of deformation of the lattice of rods. The intensification of turbulent momentum transfer in the channels in the azimuthal direction in the area of the gaps between the rods is demonstrated. The anisotropy coefficient of turbulent momentum transfer reaches 30-40 units. The performed analysis indicated a significant difference in the calculated in the framework of semi-empirical models of turbulent transfer and experimental dependences of the coefficients of turbulent transfer of momentum in the radial and azimuthal directions and the coefficients of anisotropy of turbulent transfer of momentum in rod bundles. The results of an open benchmark on the thermohydraulics of fuel assemblies showed that common commercial computational thermohydraulic codes only approximately describe the experimental data. It is shown that the intensification of turbulent momentum transfer in the channels of rod assemblies is due to the appearance of large-scale turbulent momentum transfer (secondary flows). The contribution of large-scale turbulent momentum transfer to the kinetic energy of turbulent pulsations, azimuthal turbulent shear stresses, and turbulent momentum transfer coefficients in rod assemblies is calculated. An empirical dependence of the coefficient of interchannel turbulent impulse exchange in bundles of smooth rods is obtained, on the basis of a semi-empirical model, data on interchannel turbulent impulse exchange in assemblies of smooth rods are generalized, and the intensification of interchannel turbulent exchange in close lattices of rods is explained. Data on hydraulic resistance in bundles of smooth rods are analyzed. The tasks of further research are discussed.

Optimization of a Fuel Assembly for Supercritical Water-Cooled Reactor CSR1000

As one of the Generation IV nuclear reactors, the SCWR (supercritical water-cooled reactor) has high economy and safety margin, good mechanical properties for its high thermal efficiency, and simplified structure design. As the key component of nuclear reactor, the fuel assembly has always been the main issue for the design of the SCWR. The design of the fuel assembly for CSR1000 proposed by the Nuclear Power Institute of China (NPIC) has been optimized and presented in this study, which is composed of four subassemblies welded by four filler strips and guide thimbles arranged close together in the cross-shaped passage. Aiming at improving the hydraulic buffer performance of the cruciform control rod, the scram time and terminal velocity of control rod assembly were calculated to assess the scram performance based on the computational fluid dynamics and dynamic mesh method, and the mechanical property and neutronic performance of assemblies were also investigated. It has been demonstrated that the optimized fuel assembly had good feasibility and performance, which was a promising design for CSR1000.

Analysis and optimization research on latch life of control rod drive mechanism based on approximate model

The Control Rod Drive Mechanism (CRDM) is an essential part of the reactor, which realizes the start-stop and power adjustment of the reactor by lifting and lowering the control rod assembly. As a moving part in CRDM, the latch directly contacts with the control rod assembly, and the life of latch is closely related to the service life of the reactor. In this paper, the relationship between the life of the latch and the step stress, friction stress, and impact stress in the process of movement is analyzed, and the optimization methodology and process of latch life based on the approximate model are proposed. The design variables that affect the life of the latch are studied through the experimental design, and the optimization objective of design variables based on the latch life is established. Based on this, an approximate model of the life of the latch is built, and the multi-objective optimization of the life of the latch is optimized through the NSGA-II algorithm.

Radiation Tolerant 3D Laser Scanner for Structural Inspections in Nuclear Reactor Vessels and Fuel Storage Pools

Accurate and timely assessment of displacements and/or structural damages in nuclear reactor vessels’ components is a key action in routine inspections for planning maintenance and repairs but also in emergency situations for mitigating consequences of nuclear incidents. Nevertheless, all these components are maintained underwater and reside in high-radiation fields thus imposing harsh operative conditions to inspection devices which must cope with effects such as Cerenkov radiation background, Total Ionizing Radiation (TID), and occlusions in the detectors’ field of view. To date, ultrasonic techniques and video cameras are in use for inspection of components’ integrity and with measurements of volumetric and surface crack opening displacements, respectively. The present work reports the realization of a radiation tolerant laser scanner and the results of tests in a nuclear research reactor vessel for acquisition of 3D models of critical components. The device, qualified for underwater operation and for withstanding up to 1 MGy of TID, is based on a 515 nm laser diode and a fast-scanning electro-optic unit. To evaluate performances in a significant but controlled environment, the device has been deployed in the vessel of a research reactor operated by ENEA in the Casaccia Research Centre in Rome (Italy). A 3D model of the fuel rods assembly through a cooling water column of 7 m has been acquired. The system includes proprietary postprocessing software that automatically recognizes components of interest and provides dimensional analysis. Possible application fields of the system stretch to dimensional analysis also in spent nuclear fuel storage pools.