Rest Seats Research Articles

Fracture Resistance of Zirconia Surveyed Crowns With Digitally Designed and Hand-Modified Occlusal Rest Seats.

Background In light of the trend of using zirconia crowns, clinicians will likely face abutment included in removable partial dentures (RPD) designs with existing zirconia. However, the decision to replace the existing crown with a surveyed crown or modify the existing crown to accept the RPD is unclear. To the best of our knowledge, there is a lack of literature on the effect of preparing a rest seat on the existing monolithic zirconia crown in the patient's mouth on the fracture resistance of the crown. Therefore, in this study, we aimed to evaluate the fracture resistance of computer-aided design/computer-aided manufacturing (CAD/CAM) zirconia surveyed crowns with digitally designed rest seats and hand-modified rest seats. Methods Thirty CAD/CAM zirconia surveyed crowns were digitally designed and fabricated and divided into groups (n=10 per group) as follows: Group 1 comprised surveyed crowns with no occlusal rest seat; Group 2 comprised surveyed crowns with a digitally designed mesial rest seat; and Group 3 comprised surveyed crowns with a hand-modified mesial rest seat. Then, with all the crowns cemented to metal dies, the specimens were subjected to a fracture resistance test using a universal testing machine (Model 8501 Instron, Norwood, MA, USA). Results Surveyed crowns without any rest seat and those with digitally created and hand-modified rest seats displayed different fracture resistances: crowns with no rest seat offered the highest fracture resistance (5831 ± 895.15 N), followed by those with a digitally designed and milled rest seat (5280 ± 1673.33 N). Crowns with a hand-modified rest seat provided the lowest fracture resistance (4976 ± 322.5 N). Based on our results, surveyed crowns without a rest seat displayed higher fracture resistance than those with a rest seat. Conclusion The fracture resistance of crowns with a digitally designed and milled rest seat was statistically similar to that of control crowns with no rest seat, whereas hand-modified rest seats significantly reduced the fracture resistance of surveyed zirconia crowns.

A Preliminary Study on the Accuracy of Cast Metal Removable Partial Denture Frameworks Produced from Wax, Printed, and Milled Patterns

To compare the accuracy of two digital workflows for producing resin patterns to be cast into metal frameworks compared to an identical framework manufactured conventionally from a wax pattern. Nine casts were duplicated from a maxillary master cast of a partially edentulous arch. Their accuracy was determined by measuring the same points in two and three dimensions using a reflex microscope, which was also used to measure all frameworks to an accuracy of 4 μm. The same design was used throughout. Three casts were used to make a framework conventionally from an invested wax pattern. Six casts were scanned, and a digital pattern created. Three patterns were milled from a resin block, and three were 3D printed with resin. Then each pattern was cast. The sample size precluded direct statistical conclusions, but no significant differences were found. Duplicate models showed minimal differences compared to the master cast. All patterns and all frameworks showed some level of difference compared to the master cast, but no differences were greater than those reported in the literature as being clinically acceptable. The maximum overall discrepancy between the cast frameworks was 0.64 mm, and at the rest seats was 0.262 mm. Within the limitations of this study, given the very small actual differences both within and between the groups of the three different workflows, the use of digitally produced resin patterns prior to their being cast as metal frameworks is both feasible and well within the accepted limits for clinical acceptability.

Digital workflow to produce 3D-printed incisal facial indirect restoration with lingual rest seats to support a removable partial denture

A technique for fabricating lingual rest seats and indirect incisal restorations using a digital workflow is described. After intraoral scanning, the incisal edge position of the restoration and lingual rest seats for a subsequent removable partial denture (RPD) were designed digitally. Adaptation was evaluated with trial restorations, and definitive restorations were printed from a 3-dimensional resin (Varseo Smile Crown Plus Bego; Wilcos). The restorations were cemented with a heated composite resin (Tetric N; Ivoclar AG) polymerized for 40 seconds. The RPD was fabricated and delivered following a conventional technique. This standard, rapid, cost-effective, and straightforward approach allows a controlled and standardized process to obtain lingual rest seats and incisal restorations simultaneously, providing support for a successful Kennedy Class I RPD.

Wear, Fatigue and Fracture Resistance of Different Monolithic CAD/CAM Onlays As Abutments for Acetal Resin or Cobalt-Chromium Removable Partial Denture Frameworks.

To assess wear, fatigue, and fracture resistance of different CAD/CAM onlays, milled from monolithic Zirconia (Zr), hybrid ceramic (EN), and lithium disilicate (LS), when used as abutments for removable partial denture frameworks fabricated from acetal resin (AR) or cobalt-chromium (Co-Cr). Standard onlays and RPD framework were designed and milled using CAD/CAM. Onlays were cemented with resin cement to identical teeth models. The RPD's occlusal rest surface and the ceramic onlays' rest seats were both 3D scanned before and after 750,000 mechanical load cycles (50 N) and 8,000 thermal cycles (5-55°C) in a chewing simulator. The volumetric loss was measured using 3D image processing software, and the failure of the samples was detected using a stereomicroscope. The fracture resistance was tested by loading to failure in a universal testing machine. The fatigue failure results were analyzed with Fisher's exact probability test and the wear and fracture resistance data were analyzed using two-way ANOVA and Bonferroni Post-hoc test (P<0.05). A significant difference (p<0.05) was found between the tested experimental groups in wear, fatigue, and fracture resistance. Zr/Co-Cr combinations exhibited the least wear and the highest fatigue and fracture resistance (P<0.05), while the highest wear and least fatigue and fracture resistance were recorded for EN/AR group (p<0.05). Zr onlays demonstrated a conservative treatment option with superior mechanical behavior when used as an onlay abutment, regardless of the RPD framework material used. The AR framework is not recommended in the posterior region for removable partial dentures.

Fit accuracy in the rest region of RPDs fabricated by digital technologies and conventional lost-wax casting: a systematic review and meta-analysis

BackgroundDigital technologies have recently been introduced into the fabrication of removable partial dentures (RPDs). However, it is still unclear whether the digitally fabricated RPDs fit better than conventionally cast ones in the rest region. The aim of this study was to evaluate the fit accuracy in the rest region of RPDs fabricated by digital technologies and compare it to those made by conventional lost-wax (CLW) technique.MethodsA comprehensive search was conducted in Cochrane Library, PubMed, EMbase, Web of Science and SpringerLink. Studies published up to August 2022 were collected. Two authors analyzed the studies independently and assessed the risk of bias on the modified methodological index for non-randomized studies (MINORS) scale. The mean values of gap distance between rests and corresponding rest seats of each study were extracted as outcome. A random-effects model at a significance level of P < 0.05 was used in the global comparison and subgroup analysis was carried out.ResultsOverall, 11 articles out of 1214 complied with the inclusion criteria and were selected, including 2 randomized controlled trials (RCTs), 1 non-randomized clinical trial and 8 in vitro studies. Quantitative data from Meta-analysis revealed that fit accuracy in the rest region of RPDs fabricated with CLW showed no statistically significant difference with digital techniques (SMD = 0.33, 95%CI (-0.18, 0.83), P = 0.21). Subgroup analysis revealed a significantly better fit accuracy of CLW-fabricated RPDs in the rest region than either additive manufacturing (AM) groups or indirect groups (P = 0.03, P = 0.00), in which wax or resin patterns are milled or printed before conventional casting. While milled RPDs fit significantly better than cast ones in the rest region (P = 0.00). With digital relief and heat treatment, hybrid manufactured (HM) clasps obtained better fit accuracy in the rest region (P < 0.05). In addition, finishing and polishing procedure had no significant influence in the fit accuracy in all groups (P = 0.83).ConclusionsRPDs fabricated by digital technologies exhibit comparable fit accuracy in rest region with those made by CLW. Digital technologies may be a promising alternative to CLW for the fabrication of RPDs and additional studies are recommended to provide stronger evidence.Trial registrationCRD42020201313.

Fracture resistance of zirconia surveyed crowns with four different occlusal rest seat designs.

To determine the fracture resistance of chairside computer-aided design and computer-aided manufacturing (CAD-CAM) zirconia surveyed crowns for a mandibular first molar without occlusal rest and with four different rest seat designs. Seventy CAD-CAM zirconia 4Y-PSZ (IPS e.max ZirCAD MT for CEREC A1, C15, Ivoclar Vivadent) crowns (14 specimens/group) were designed and fabricated with a dental chairside CAD-CAM system (CEREC PrimeScan, and CEREC MCXL Dentsply Sirona). The restorations were divided into groups according to the following rest seat designs: (1) Surveyed crown without rest seat, (2) surveyed crowns with disto-occlusal rest seat, (3) surveyed crowns with disto-occlusal extended rest seat, (4) surveyed crowns with interproximal rest seat, and (5) continuous rest seat. Crowns were treated with a primer system (Monobond Plus, Ivoclar Vivadent) and cemented using resin luting cement (Multilink Automix, Ivoclar Vivadent) to resin-printed dies (Grey Resin V4, FormLabs). Subsequently, the crowns were subjected to 200,000 load cycles at 1Hz with 20 N force and then loaded with a steel indenter until fracture. The test results were analyzed with one-way Analysis of Variance (ANOVA) and HSD Tukey post-Hoc test. The mean fracture resistance of surveyed crowns without and with different rest seats was significantly different from each other. Surveyed crowns with no rest seat displayed the highest resistance (4238 N) followed by crowns with continuous rest seat (3601 N), crowns with disto-occlusal extended rest seat (3283 N), and crowns with disto-occlusal rest seat (3257 N). Crowns with interproximal rest seat displayed the lowest fracture resistance (2723 N). Surveyed crowns without rest seats had a higher fracture resistance than crowns with rest seats Surveyed crowns with interproximal rest seats presented the lowest fracture resistance among all rest seat designs. Crowns with disto-occlusal rest seats, disto-occlusal extended rest seats, and continuous rest seats displayed similar fracture resistance.

Evaluation of the Retentive Forces from Removable Partial Denture Clasps Manufactured by the Digital Method

The purpose of this study was to evaluate the retentive forces over time of removable partial denture clasps fabricated by the digital method. Occlusal rest seats were fabricated on three premolar teeth fixed in acrylic blocks (9 × 20 × 40 mm). Digitization of the teeth was performed using a laboratory scanner (Zirkonzahn Scanner S600 GmbH, Gais, Italy). After the analysis and determination of the insertion axis, two types of clasps with mesial occlusal rests were designed per tooth: the back-action and the reverse back-action clasps, using the Partial Planner Zirkonzahn program. The file was sent for fabrication of six metal clasps from a cobalt-chromium SP2 alloy in the EOSINT M270 system by a direct laser sintering process. The Instron 5544 universal testing machine was used to perform 20,000 cycles of clasp insertion and removal in the corresponding tooth with a load cell of 100 N and a speed of 2.5 mm/s. The retentive force was recorded for each of the 1000 cycles, and the change in retention over time was calculated. Statistical analysis was performed using the nonparametric Mann–Whitney test and a significance level of 5%. At 16,000 cycles, a maximum change in retention of 3.74 N was recorded for the back-action clasps and a minimum of −24.28 N at 1000 cycles for the reverse back-action clasps. The reverse back-action clasps exhibited statistically significant lower change in retention than the reverse-action clasps at 4000 and 5000 cycles. No differences were observed in the remaining cycles. During the 20,000 cycles, the change in retention was low regardless of the type of clasp. For most cycles, there were no differences in the change in retention between the two types of clasps.

Fracture Strength of Composite Rest Seats: An In Vitro Comparative Study of Different Composite versus Amalgam Restorations

Occlusal rest provides support for removable partial dentures (RPD). Rest seats are ideally prepared in enamel, but the abutment teeth might be restored or need restorations. This study compared the fracture strength of abutments restored with composite to amalgam restorations after rest seat preparation. Disto-occlusal cavities were prepared in 30 extracted human maxillary premolars. The specimens were allocated in three groups (n = 10) based on the type of restoration. All the specimens were exposed to thermomechanical aging followed by cycling loading. Fracture strength was tested using a universal testing machine, and then, the fracture mode was recorded. The data were analyzed using Kruskal–Wallis test with a significance level set at 0.05. The fracture mode was recorded as catastrophic or non-catastrophic. The fracture strength between all tested groups showed no significant difference. The highest and lowest fracture strength were recorded on amalgam and Tetric N-Ceram groups, respectively. Composite Tetric N-Ceram showed equal distribution of fracture sites on the restorative materials and teeth, it also displayed the highest number of non-catastrophic fractures unlike other groups where the fracture occurred more within the restorations. The fracture strength of composite was comparable to that of amalgam restorations with prepared rest seats.

Performance of bulk-fill versus conventional nanocomposite resin restorations supporting the occlusal rests of removable partial dentures: An in vitro investigation

Statement of problemPlacing removable partial denture (RPD) rests on composite resin restorations has long been a debatable issue. Despite developments in composite resins such as nanotechnology and bulk-filling techniques, studies investigating the performance of composite resin restorations when used to support occlusal rests remain scarce. PurposeThe purpose of this in vitro study was to investigate the performance of bulk-fill versus incremental (conventional) nanocomposite resin restorations when they are used to support RPD rests under functional loading. Material and methodsThirty-five caries-free intact maxillary molars of similar coronal size were collected and divided into 5 equal groups (n=7): Enamel (Control) group: rest seats prepared entirely in enamel; Class I Incremental group: Class I cavities restored with incrementally placed nanohybrid resin composite resin (Tetric N-Ceram); Class II Incremental group: Mesio-occlusal (MO) Class II cavities restored with Tetric N-Ceram; Class I Bulk-fill group: Class I cavities restored with high-viscosity bulk-fill hybrid resin composite (Tetric N-Ceram Bulk-Fill); and Class II Bulk-fill group: MO Class II cavities restored with Tetric N-Ceram Bulk-Fill. Occlusal rest seats were prepared mesially in all groups, and clasp assemblies were fabricated and cast in cobalt chromium alloy. Specimens with their clasp assemblies were subjected to thermomechanical cycling using a mechanical cycling machine (250000 masticatory cycles) and 5000 thermal cycles (5 °C to 50 °C). Surface roughness (Ra) was measured with a contact profilometer before and after cycling. Fracture analysis was done using stereomicroscopy, and margin analysis was done with a scanning electron microscope (SEM) before and after cycling. Statistical analysis of Ra was conducted using ANOVA followed by the Scheffé test for between-group comparison and paired t test for within-group comparison. The Fisher exact probability test was used for fracture analysis. The Mann–Whitney test was used for between-group comparison and Wilcoxon signed rank test for within-group comparison for the SEM images (α=.05). ResultsMean Ra increased significantly after cycling in all groups. Significant differences in Ra were found between enamel and all 4 resin groups (P<.001), with no significant differences between incremental and bulk-fill resin groups for both Class I and II specimens (P>.05). No significant differences were found between the 2 resin groups with regard to fracture and margin analysis (P>.05). ConclusionsThe surface roughness of enamel was significantly lower than that of both incremental and bulk-fill nanocomposite resins before and after functional loading. Incremental and bulk-fill nanocomposite resins showed comparable performance in terms of surface roughness, fracture behavior, and marginal adaptation.

Comparison between digital superimposition and microcomputed tomography methods of fit assessment of removable partial denture frameworks

Statement of problemThe fit of removable partial denture frameworks should be assessed to optimize clinical adaptation. Potential discrepancies between framework and supporting structures are typically precisely measured with negative subtracts and high-resolution equipment. The growth of computer-aided engineering technology allows the development of new methods for the direct evaluation of discrepancies. However, how the methods compare is unclear. PurposeThe purpose of this in vitro study was to compare 2 digital methods of fit assessment based on direct digital superimposition and microcomputed tomography indirect analysis. Material and methodsTwelve cobalt chromium removable partial denture frameworks were fabricated by conventional lost-wax casting or additive manufacturing techniques. The thickness of the gap between occlusal rests and respective definitive cast rest seats (n=34) was evaluated by using 2 different digital methods. Silicone elastomer impressions of the gaps were obtained, and microcomputed tomography measurements were used as controls for validation purposes. Digitization of the framework, the respective definitive cast, and the combination was followed by digital superimposition and direct measurements with the Geomagic Control X software program. Because normality and homogeneity of variance were not verified (Shapiro-Wilk and Levene tests, P<.05), the data were analyzed with Wilcoxon signed rank and Spearman correlation tests (α=.05). ResultsThe thicknesses measured by microcomputed tomography (median=242 μm) and digital superimposition (median=236 μm) did not reveal statistically significant differences (P=.180). A positive correlation (ρ=0.612) was detected between the 2 methods of assessing fit. ConclusionsThe frameworks presented median gap thicknesses under the limit of clinical acceptability without differences between the proposed methods. The digital superimposition method was determined to be as acceptable as the high-resolution microcomputed tomography method for assessing removable partial denture framework fit.

A digital workflow for complete arch rehabilitation with zirconia crowns on restored posterior teeth and a polyetheretherketone framework denture.

A clinical and laboratory workflow for the digital design and fabrication of zirconia crowns and polyetheretherketone removable partial dentures for complete arch rehabilitation is described. The definitive crowns and polyetheretherketone framework can be delivered simultaneously because of the digital design and milling fabrication with retentive areas, guide planes, and rest seats in high-translucency zirconia crowns. The workflow helps simplify clinical and laboratory procedures and reduces patient visits and chairside time.

Effect of various printing parameters on the accuracy (trueness and precision) of 3D-printed partial denture framework

ObjectivesTo measure and compare the accuracy of 3D-printed materials used for RPD production to improve workflow and eliminate errors in manufacturing. MethodsA partially edentulous maxilla (Kennedy Class III, modification 1) was prepared and designed with proximal plates, rest seats and clasps in one first premolar, one canine and two second molars. A total of 540 3D printed RPD frameworks were 3D printed with three different types of resin (DentaCAST (Asiga, Australia), SuperCAST (Asiga, Australia) and NextDent (3D Systems, Netherlands)). To evaluate the trueness of the printing materials, they were printed with three types of layer thickness: 50 μm, 75 μm and 100 μm, using two types of build angles: 0° and 45° and three types of plate locations: side, middle and corner. After production, all specimens were scanned and superimposed with a control sample that was digitally designed. Using the initial alignment and best-fit alignment method, the root mean square error (RMSE) was calculated. To capture region specific discrepancy, 10 points of XYZ internal discrepancy within RPDs were measured and Euclidean error was calculated. Data was statistically analysed using Shapiro-Wilk and Kruskal-Wallis tests, one-way ANOVA and T-test (SPSS Version 29) and MATLAB (R2022b). ResultsOptimal results were found using 45°, middle of the build plate and layer thicknesses of 100 μm (115 ± 19 μm, DentaCAST), 75 μm (143 ± 14 μm, NextDent), 50 μm (98 ± 35 μm, SuperCAST), which were clinically acceptable. Results were statistically significant when comparing layer thickness in each testing group (p < 0.001). Layer thickness was a primary parameter in the determination of print accuracy among all materials (p < 0.001). Higher discrepancies and failures were observed in 0° prints. No statistically significant difference was found in material usage between build angles or layer thickness (p > 0.005). ConclusionsAll three 3D printing materials exhibited clinically acceptable RMSE results with a build angle of 45° with a printing layer thickness of 50 μm for SuperCAST, 75 μm NextDent and 100 μm for DentaCAST. The highest discrepancies were mostly found in posterior clasps, while the lowest discrepancy was found in palatal straps. Despite unoptimized spacing of prints, frameworks configured to print in the middle of the build plate result in the least printing failures.

Evaluation of PEEK and zirconia occlusal rest designs for removable partial dentures based on finite element analysis.

Purpose We aimed to assess removable partial denture occlusal rests composed of polyether-ether-ketone (PEEK) and zirconia, using finite element analysis.Methods Three-dimensional PEEK and zirconia rest models, including the occlusal rest (1.5 mm thickness at the basal portion, 3.0 mm width) and minor connector (1.5 mm thickness, 6.0 mm height), and rest seat models with mechanical properties of enamel were constructed. The radius of transitional curvature between the rest and minor connector was 0.1-0.5 mm. The rest and rest seat model interfaces were set as frictional contacts (μ = 0.1), and the base of the rest seat model was restrained in all the directions. A 100 N downward load was applied perpendicular to the bottom surface of the minor connector. The maximum value of the first principal stress (Max-S1) was compared to the flexural and fatigue strengths of each material. Occlusal rests with 1.0-2.0 mm thickness, 2.0-3.5 mm width, and 0.5 mm radius of transitional curvature were analyzed.Results Max-S1 was observed at the transitional part and decreased with increasing radius of the transitional curvature, rest width, and thickness. PEEK rests with at least 1.5 mm thicknesses and 3.0 mm widths showed lower Max-S1 than the flexural strength. Max-S1 of all PEEK rests exceeded the PEEK fatigue strength, whereas Max-S1 of the zirconia rests was lower than the zirconia fatigue strength.Conclusions Zirconia occlusal rests with conventional metal rest designs have sufficient fatigue strength. PEEK occlusal rests have insufficient fatigue strength and may not withstand repeated mastication.

Adaptation of removable partial denture rest seats in prostheses made with selective laser sintering or casting techniques: A randomized clinical trial

Statement of problemNew fabrication techniques have been developed for removable partial denture (RPD) frameworks although studies validating the clinical application of these techniques are scarce. PurposeThe purpose of this clinical study was to compare the adaptation of RPD framework rests made with conventional casting or computer-aided design and computer-aided manufacturing (CAD-CAM) with selective laser sintering (SLS) at the clinical evaluation and 1 year after the delivery of the prostheses. Material and methodsThis triple-blinded pilot study included 18 participants presenting with maxillary and/or mandibular partial edentulism, of which only 7 returned for the second measurement 1 year after prosthesis delivery. Participants were randomly assigned to 1 of 2 groups depending on whether the RPD framework was made with SLS or conventional lost-wax casting. The adaptation of the RPD at the rest seat area was evaluated by injecting a silicone material on the abutment tooth before seating. The silicone specimens were then sectioned transversely and measured with a scanning electron microscope. The statistical analysis was performed with a linear mixed-effect model with the intention to treat and with a 3-factor repeated measures ANOVA (α=.05). ResultsAt the metal framework evaluation (T0), the prostheses made with SLS showed a mean ±standard deviation adaptation of 398 ±45 μm, while those made with conventional casting presented a mean ±standard deviation adaptation of 176 ±41 μm (P=.009). One year after the delivery of the prostheses (T1), the adaptation of the frameworks made with conventional casting was still significantly better (88 ±6 μm versus 197 ±94 μm, P=.03). ConclusionsFrameworks made with SLS showed worse clinical accuracy at the rest than frameworks produced with conventional casting.

Fracture resistance of CAD/CAM restorative materials in mismatched removable partial denture rests: An in vitro experimental and finite element analysis.

To evaluate the fracture resistance of computer-aided design and computer-assisted manufacturing restorations as the abutment of removable partial dentures, experimental blocks, with the rest seat made of feldspar, hybrid resin composite, lithium disilicate glass ceramic, or zirconia, were subjected to loading by a metallic occlusal rest. The rest contacted the rest seat with an accurate fit and two mismatch contact conditions: bottom and sidewall contact. Zirconia exhibited the highest fracture load, and the fracture load of the accurate fit was significantly higher than that of the sidewall contact (p<0.05) and insignificantly higher than that of the bottom contact (p>0.05). A finite element analysis of the sidewall contact revealed a higher tensile stress concentration at the bottom of the rest seat than the other contact conditions. The mismatch between the rest and the restoration reduced fracture resistance, while zirconia as the abutment withstood the average occlusal force of the posterior region.

Comparative clinical evaluation of removable partial denture frameworks fabricated traditionally or with selective laser melting: A randomized controlled trial

Statement of problemThe clinical efficacy of selective laser melting (SLM) for fabricating removable partial dentures (RPDs) is not well established. PurposeThe purpose of this clinical study was to compare the performance of SLM-fabricated frameworks with that of those fabricated via traditional lost wax casting. Material and methodsA double-blind, randomized, crossover design was used to compare cobalt chromium partial denture frameworks (n=29) fabricated by using SLM or traditional methods. The time taken for adjustments and the clinical fit and stability of the adjusted frameworks were appraised. The accuracy of the frameworks was assessed by measuring the space between the occlusal rest seat and the corresponding rest seat. Statistical comparisons between the 2 frameworks were carried out by using a linear mixed-effect model for repeated measurements (α=.05). ResultsFrameworks fabricated by using both SLM and traditional techniques had an acceptable fit based on subjective clinical evaluation. The overall mean ±standard deviation space between the occlusal rest and rest seat for SLM frameworks (273.7 ±44.5 μm) was comparable with that of traditional frameworks (242.2 ±44.5 μm). The clinical fit adjustment time, 7.76 ±6.43 minutes for SLM and 5.49 ±6.39 minutes for traditionally fabricated frameworks, was statistically similar (P=.067). ConclusionsDentures fabricated via SLM and traditional techniques had comparable accuracy of fit and clinical fitting time.

승객 만족도 향상을 위한 연안여객선 실내공간 개선방향 연구

The purpose of this study is to investigate passenger satisfaction and suggest improvement directions of interior spaces for improving passenger satisfaction in the accommodation area of coastal ferry, Ro-Pax ships. First, previous studies, references, and examples reviewed. Then, the questionnaire survey identifies the characteristics of passengers, passenger satisfaction, space organization and design, interior design problems, and requirements for improving interior spaces. The passenger questionnaires are compared and analyzed with expert questionnaires conducted in previous studies. From the results of research, it mainly suggests that various types of handrails for the weak, color planning and installing digital information system, rearranging the space with usage. With result of the questionnaire survey, improvement plans suggest that different information system for the user, sign design with readability and identification, space and door design for wheelchair users, standard of handrail design, design guideline of staircase, efficient traffic flow of a restaurant, esay accesible to the rest seat, affordable space organization.

Finite Element Analysis of Restored Principal Abutment in Free-End Saddle Partial Denture.

PurposeThis study analyzed the stress distribution of restored principal abutments in free-end saddle partial dentures.Materials and MethodsThe mandibular second premolar was modeled with class II cavity restored with composite resins (Tetric N Ceram and Charisma Smile). Finite element analysis (FEA) was used to examine the stresses under 200-N static load vertically and horizontally and the results were graphically illustrated in the form of von Mises stresses.ResultsThe von Mises stress distribution patterns of two different composite resins (Tetric N Ceram and Charisma Smile) were very similar in all modes of loading.ConclusionComposite resins with a similar modulus of elasticity in class II cavities with occlusal rest seat preparation had similar stress distributions.Clinical SignificanceNanohybrid composite resin restorations may be a possible method for preparing abutments for receiving elements of the removable partial denture (RPD).

Accuracy of metal 3D printed frameworks for removable partial dentures evaluated by digital superimposition

ObjectivesTo evaluate the accuracy of metal 3D printed frameworks (MEP group) for removable partial dentures (RPDs) by digital superimposition, in comparison to that of frameworks produced by the conventional (CON group) and resin printing/casting (RPC group) workflows. MethodsA partially edentulous maxillary dentiform was prepared with rest seats and guiding planes on the right canine, left first premolar, and left second molar. Thirty master casts were prepared via repeated impressions of the dentiform. Frameworks were fabricated by three different workflows (n = 10 for each group). The internal discrepancies of the frameworks were assessed at 12 points by digital scanning with an optical triangulation principle-based tabletop scanner and superimposition using a reference best-fit alignment method. First, the master cast was scanned alone. Subsequently, a thin silicone material was applied to the framework and fitted onto the master cast, after which the framework was removed. Finally, the master cast with the silicone material attached was rescanned. The data from the two scans were matched, with the reference being the area not occupied by the silicone. ResultsFor the CON, MEP, and RPC groups, respectively, the mean overall internal discrepancies (279.72 µm, 241.02 µm, and 331.70 µm), and the mean internal discrepancies on palate areas (292.92 µm, 250.72 µm, and 355.84 µm) and rest seat areas (240.12 µm, 211.91 µm, and 259.26 µm) did not significantly differ among the three fabrication methods (p = 0.558, 0.542, and 0.774). SignificanceThe reference best-fit alignment of scan datasets is a useful approach to evaluate the internal discrepancy of frameworks. Metal 3D printing produces RPD frameworks that are comparable to conventional frameworks and meet clinical standards.

Fit accuracy of removable partial denture metal frameworks produced by CAD-CAM – a clinical study

Objectives: To assess the effect of a CAD-CAM protocol fabrication on the clinical fit accuracy of removable partial denture metal frameworks to abutment teeth. Methods: Fifteen patients with partial edentulism were selected to participate in this clinical study, and twenty dental arch rehabilitations were planned. For each dental arch (n=20), two cobalt-chromium frameworks were produced through two protocols: CAD-CAM production (experimental group); and conventional lost-wax casting technique (control group). Clinical fit accuracy was assessed using an indirect quantitative method to evaluate the gap between the framework occlusal rest and the corresponding rest seat. A silicone mold of that gap was obtained, digitized, and analyzed by micro-computed tomography. The two silicone molds obtained for each occlusal rest were overlapped and evaluated for thickness and volume. Data were analyzed with the paired t test for silicone thickness results and the Wilcoxon test for silicone volume results (α= 0.05). Results: Considering the two dependent variables under study, no statistically significant (p=0.441 for silicone thickness and p=0.204 for silicone volume) differences were found between groups. Conclusions: The results of this study suggest that the CAD-CAM protocol applied is a viable method for the production of removable partial denture metal frameworks. (Rev Port Estomatol Med Dent Cir Maxilofac. 2021;62