Resonant Output Research Articles

A one-step fabrication method of flexible magnetostrictive fiber ribbon based on Fe50Co50 alloy and its characteristics study

Magnetostrictive materials are widely used in sensors, actuators and micro-nano electronics because of their excellent performance. However, traditional rigid magnetostrictive materials are difficult to adapt to the flexible and deformable structure of flexible electronic devices. In order to solve the deformation, sensing and control problems in the field of flexible electronics, a one-step new method of is proposed to deposit Fe50Co50 fiber ribbons with reciprocated and loop structures on flexible substrate. Helmholtz coil is designed to test the magnetostrictive positive effect ability of Fe50Co50 ribbon, and its magnetostrictive strain curve is analyzed. Furthermore, frequency domain characteristics of Fe50Co50 ribbon are tested, and the influence of externally driving magnetic field on elastic layer materials and resonance output characteristics is analyzed. The experimental results show that Fe50Co50 ribbon exhibits good low-frequency magnetic field characteristics. And free end displacement of Fe50Co50 ribbon based on loop structure, under 12 mT alternating magnetic field and 134 mT bias magnetic field, reaches a peak-to-peak value of 870 μm for first-order resonance, and 320 μm for second-order resonance. This verifies that Fe50Co50 ribbon possesses the expected properties that magnetostrictive materials should have, and innovatively breaks through the technical bottleneck of manufacturing flexible micro-nano magnetostrictive energy exchange components.

A Novel Design Strategy for Cantilever Based MEMS Piezoelectric Vibration Energy Harvesters: FEM Parametric Analysis and Modeling

Vibration-based energy-harvesting (VEH) technology is a viable alternative power source that addresses the issue of battery capacity constraints in portable electronic devices. A novel design strategy for developing a piezoelectric vibrational energy harvester (PVEH) based on a microelectromechanical system (MEMS) is proposed in this paper. Through FEM simulation and analysis, a correlation between the proof mass coverage (PMC) and piezoelectric coverage (PEC) for energy harvesters with different beam geometries is developed. The results show that the output power and resonant frequencies of the energy harvester are strongly dependent on the amount of PMC, PEC, and beam geometry. The optimum piezoelectric layer length for a PVEH depends on the amount of PMC and geometry of the beam. Moreover, as the PMC increases, the output power is found to be increasing. The structure with 80% PMC provides maximum output power. Also, a trapezoidal beam will give a lower resonant frequency than a rectangular beam. Thus the optimum design methodology for a cantilever-based MEMS PVEH in a given layout is to select the trapezoidal-shaped beam with a PMC of 60% to 80% and piezoelectric layer length equal to the beam length. This method would provide optimised resonant frequency and output power performance. Additionally, an analytical model is developed for the optimised cantilever PVEH based on trapezoidal geometry, and the simulation findings are validated with the analytical results.

Interoperable square‐circular coupled coils for wireless electric vehicle battery charging system with different misalignments

AbstractA substantial interest in inductive power transfer (IPT) is due to its straight forwardness and dependability in charging electric vehicle (EV) batteries for researchers. The mutual inductance (MI) plays a critical role in the IPT system as it enables efficient power transfer. Therefore, it is imperative to examine the MI between the two coils that are connected through inductive coupling. This work investigates the MI and efficiency of connected coils in interoperable conditions. The transmitter coil is arranged in the shape of a square (TxS), whereas the reception coil is arranged in the shape of a circle (RxC). A concise and user‐friendly collection of design guidelines for S‐S compensated resonant inductive power transfer (SS‐RIPT) systems the design concepts efficiently mitigate the possibility of systematically and unambiguously setting the specifications for a given load profile. A 3.6‐kW setup has been constructed and validated by finite element analysis and experimental testing, following the design specifications. The availability of suitable testing equipment in the laboratory influenced the choice of a resonance frequency and output voltage for a 3.6 kW system.

Resonant Metasurface-Mediated Light Output of Barium Fluoride Scintillators: Design and Simulation

Resonant Metasurface-Mediated Light Output of Barium Fluoride Scintillators: Design and Simulation

Design and analysis of mode-matched decoupled mass MEMS gyroscope with improved thermal stability

This paper presents an efficient design approach for microelectromechanical systems (MEMS) gyroscope considering the design constraint of MEMSCAP’s Silicon-on-Insulator Multi-User MEMS Processes (SOIMUMPs). A design for a decoupled mass MEMS resonant gyroscope with tuning electrodes is presented to minimize cross-axis coupling and optimize the gyroscope’s performance. The device features a size of 1.8 ×2.772 mm2 . A decoupled mass MEMS gyroscope has been designed using a novel mechanical beam configuration that optimizes the structural design to reduce unwanted interactions between drive and sense axes motions. Mode order has been achieved by obtaining the first two modes as drive and sense modes at 9946.3 Hz and 10 202.7 Hz, respectively. Parallel plate electrostatic tuning electrodes have been added to adjust and match the drive and sense modes at the resonant frequencies of 9946 Hz. This mode matching is crucial for optimizing gyroscope performance, accuracy, and sensitivity. The effects of temperature variation on the performance of the designed decoupled mass MEMS gyroscope have been investigated, particularly in terms of its mode-matched operation achieved using tuning electrodes. Finite element method (FEM) simulations were conducted, demonstrating that thermal stability was achieved, and mode-matched operation was maintained within the temperature range of −40 °C to 80 °C. The gyroscope exhibits enhanced performance compared to existing MEMS gyroscopes under mode-matched conditions, featuring a lower temperature coefficient of frequency (TCF) at 0.0415 Hz °C−1 in the drive mode and 0.0165 Hz °C−1 in the sense mode. FEM analysis for the fabrication process tolerances has been done, where MEMS gyroscope’s resonant frequencies, output capacitance, output displacement, and sense mode quality factor have shown negligible changes to fabrication process tolerances. Transient analysis was conducted using CoventorWare MEMS+ 3D schematic, which was integrated with MATLAB Simulink to measure the MEMS gyroscope’s output response, which corresponded with the varying input angular velocity signal.

Optimizing inset-fed rectangular micro strip patch antenna by improved particle swarm optimization and simulated annealing

ABSTRACT The recent wireless communication systems require high gain, lightweight, low profile, and simple antenna structures to ensure high efficiency and reliability. The existing microstrip patch antenna (MPA) design approaches attain low gain and high return loss. To solve this issue, the geometric dimensions of the antenna should be optimized. The improved Particle Swarm Optimization (PSO) algorithm which is the combination of PSO and simulated annealing (SA) approach (PSO-SA) is employed in this paper to optimize the width and length of the inset-fed rectangular microstrip patch antennas for Ku-band and C-band applications. The inputs to the proposed algorithm such as substrate height, dielectric constant, and resonant frequency and outputs are optimized for width and height. The return loss and gain of the antenna are considered for the fitness function. To calculate the fitness value, the Feedforward Neural Network (FNN) is employed in the PSO-SA approach. The design and optimization of the proposed MPA are implemented in MATLAB software. The performance of the optimally designed antenna with the proposed approach is evaluated in terms of the radiation pattern, return loss, Voltage Standing Wave Ratio (VSWR), gain, computation time, directivity, and convergence speed.

Using Artificial Intelligence to Improve the Accuracy of a Wrist-Worn, Noninvasive Glucose Monitor: A Pilot Study.

Self-monitoring of glucose is important to the successful management of diabetes; however, existing monitoring methods require a degree of invasive measurement which can be unpleasant for users. This study investigates the accuracy of a noninvasive glucose monitoring system that analyses spectral variations in microwave signals. An open-label, pilot design study was conducted with four cohorts (N = 5/cohort). In each session, a dial-resonating sensor (DRS) attached to the wrist automatically collected data every 60 seconds, with a novel artificial intelligence (AI) model converting signal resonance output to a glucose prediction. Plasma glucose was measured in venous blood samples every 5 minutes for Cohorts 1 to 3 and every 10 minutes for Cohort 4. Accuracy was evaluated by calculating the mean absolute relative difference (MARD) between the DRS and plasma glucose values. Accurate plasma glucose predictions were obtained across all four cohorts using a random sampling procedure applied to the full four-cohort data set, with an average MARD of 10.3%. A statistical analysis demonstrates the quality of these predictions, with a surveillance error grid (SEG) plot indicating no data pairs falling into the high-risk zones. These findings show that MARD values approaching accuracies comparable to current commercial alternatives can be obtained from a multiparticipant pilot study with the application of AI. Microwave biosensors and AI models show promise for improving the accuracy and convenience of glucose monitoring systems for people with diabetes.

First thin-disk oscillator with ceramic Yb:LuScO3 in comparison to the operation with ceramic Yb:Lu2O3

We report on the characterization and first laser operation of ceramic Yb:LuScO3 in a thin-disk oscillator. The optical performance achieved with a ceramic Yb:LuScO3 disk is compared to the one obtained with an existing ceramic Yb:Lu2O3 disk for reference. The characterization covers the measurement of the fluorescence spectra, the fluorescence lifetimes, and nomarsky imaging. The investigation on the laser operation covers the measurement of resonator losses, output powers, and thermal behavior during continuous-wave operation in a multimode thin-disk oscillator. An average output power of 149 W and a slope efficiency of 51.8% were achieved with the ceramic Yb:LuScO3 disk which reached a maximum surface temperature of about 150 °C. At the same temperature level, a disk made of the already established ceramic Yb:Lu2O3 delivered 957 W of output power with a slope efficiency of 75.7%.

RESEARCH OF STRUCTURAL AND MECHANICAL PROPERTIES OF MEAT AS AN OBJECT OF PROCESSING IN MEAT COMMINUTOR

Reliable assessments of the state of modern energy show the relevance of scientific and technical developments aimed at solving its problems. In this regard, the use of resonance phenomena in electrical circuits with active-reactive elements acquires particular significance. Their various combinations open up exceptional opportunities for creating fundamentally new efficient energy sources. This article discusses a resonant active electrical power amplifier containing a sequence of several electrically connected active-reactive circuits, which, depending on the purpose, are excited in the voltage resonance or current resonance mode. An equivalent circuit is proposed for the proposed resonant amplifier of active electrical power, represented by two blocks, each of which consists of a sequence of inductively coupled active-reactive circuits excited at the same frequency. Calculations are presented showing the theoretical justification for the performance of the proposed scheme. The analysis of ongoing electromagnetic processes was carried out using well-known methods of the theory of electrical circuits without involving any hypotheses about the physics of resonance phenomena. It is shown that in the proposed amplifier circuit, the first block amplifies the reactive power of the harmonic signal with a high conversion coefficient, the second, with a slight gain, converts the reactive power of the harmonic signal into active power. The results of calculations are presented, illustrating the functional dependence of the integral gain on the main characteristics of the output resonant circuit. Numerical estimates of the main characteristics of the proposed circuit showed that with an appropriate choice of its parameters, high values of the output characteristics are possible, so the gain can reach a value of ~ 48. The significance of the results obtained for practice lies in their use for formulating recommendations for the creation of real efficient sources of electrical energy, the principle whose actions are based on the use of natural resonance phenomena.

28.02 W LD side-pumped CW laser operated at 2.8 µm in YSGG/Er:YSGG/YSGG crystal.

We demonstrated a 978 nm laser diode (LD) side-pumped YSGG/Er:YSGG/YSGG composite crystal with a size of Ф 3 mm × 65 mm and continuous-wave (CW) mode. By optimizing resonator length and output mirror transmittance, a maximum output power of 28.02W is generated, corresponding to slope efficiency of 17.55% and optical-optical efficiency of 12.29%, respectively. The thermal focal lengths are obtained by resonator stability condition. The laser wavelength is centered near 2.8 µm. Moreover, the beam quality factors M x2/M y2 are fitted to be 8.14 and 7.35, respectively. The above results indicate that a high-performance 2.8µm CW laser can be achieved by LD side-pumped YSGG/Er:YSGG/YSGG composite crystal with excellent heat dissipation ability, which promotes effectively the development and applications of the mid-infrared solid-state lasers.

Research on piezoelectric simulation characteristics based on ALN piezoelectric thin film structure

AlN piezoelectric thin films possess exceptional performance and find extensive applications in the fields of underwater acoustic communication and hydroacoustic sensing. To enhance the output voltage values of AlN piezoelectric thin films and optimize their structure, comprehensive simulations and analyses were carried out by using COMSOL on both circular and square film configurations. These investigations specifically focused on examining the impact of dimensional variations on resonance frequency and output voltage, as well as exploring the relationship between vibration frequency and output voltage. The findings revealed that by employing an appropriate cavity radius, increasing the thickness of the thin film can effectively enhance the output voltage. However, if the thickness surpasses 1.5 μm, the output voltage will gradually decline. Notably, the square film exhibited a significantly higher output voltage measurement of 2158 pm compared to the circular film.

Multimode auxetic piezoelectric energy harvester for low-frequency vibration

Herein, we propose a piezoelectric energy harvester (PEH) capable of vibrating in multi-degrees-of-freedom. The resonant frequency, working bandwidth, and output power of the PEH were improved by introducing an auxetic structure (AS). The proposed PEH exhibited a symmetric serpentine structure with a doubly clamped configuration comprising several proof masses at the junctions. Finite element method (FEM) simulation was conducted to investigate the characteristics of an AS PEH and a plain-structure PEH. Prototypes of the PEHs were manufactured by three-dimensional (3D) printing technology, and their performance was evaluated through vibrational energy-harvesting experimental tests. The results showed that introducing the AS reduced the first and second resonant frequencies by 49% and 44%, respectively, considerably improved the output power in the first mode (up to 2548%) and narrowed the frequency bandgap between the first two resonance modes by 29%. The proposed multimode AS PEH can operate in a low-frequency environment of less than 20 Hz. Finally, we discussed several ways of optimizing the AS. It has been found that the PEH performance could be further improved by selecting a reasonable thickness for the AS, increasing the number of periodic unit cells, and using an AS with a variable cross-section unit cell.

A New Design for Tapped-inductor Transmitter with Multiple Concurrent Resonant Frequency Outputs for Wireless Power Transfer

A New Design for Tapped-inductor Transmitter with Multiple Concurrent Resonant Frequency Outputs for Wireless Power Transfer

Compact polarization beam splitter based on metal-capped thin-film LiNbO3-on-insulator plasmonic waveguide

A compact polarization beam splitter based on a triple-waveguide plasmonic directional coupler is proposed and modeled. The directional coupler consists of two usual lithium-niobate-on-insulator (LNOI) ridge waveguides and a metal-capped plasmonic LNOI waveguide located between them. It utilizes stronger polarization dependence of modal birefringence of a plasmonic waveguide. By appropriately designing the plasmonic waveguide geometry, the TM component wave meets the resonant coupling condition and outputs at cross port. Instead, the TE component wave does not meet the resonant coupling condition, cannot be resonant in the triple-waveguide directional coupler and outputs at through port directly. Excellent performance is expected for an optimal device. First, the device shows an ultra-high polarization extinction ratio(PER) of 28.3 dB and an ultra-low insertion loss(IL) of 0.06 dB for the TE-polarized wave, and of 31.7 dB and of 0.31 dB in order for the TM-polarized wave. Second, the working bandwidth with PER > 25 dB and IL < 0.08 dB is 100 nm (1500–1600 nm) for the TE-polarized wave, and that with PER > 20 dB and IL < 0.4 dB is 30 nm (1534–1564 nm) for the TM-polarized wave. Third, the device has a compact structure of 33 μm in length and exhibits definite fabrication tolerance. Overall, the proposed device exhibits ultra-high PER and ultra-low IL, and has a compact size suitable for on-chip use. A comparison shows that present device exhibits advantage in IL and/or size over that based on other LNOI structures or the SOI platform.

Optical fractal in cryogenic environments based on distributed feedback Bragg photonic crystals.

We studied the optical fractal effect of the one-dimensional distributed feedback Bragg photonic crystals formed by semiconductor GaAs and dielectric TiO2. Light wave is transmitted in the intermediate dielectric slab and reflected back by the periodic photonic crystals at both ends, forming multiple fractal resonance output. The transmission channels expand exponentially by thickening the bulk in a cryogenic environment. The quality factor of each fractal resonant state improves with a greater periodic number of crystals. Furthermore, central wave of resonance has a blue-shift as the external pressure increases, while the influence of environment temperature on the fractal resonance could be ignored. It is hoped that our study can highlight the potential of these findings for designing multi-channel communication filters in cryogenic environments.

A Broadband, High-Power Resonant Piezoelectric Active-Valve Pump Driven By Sandwich Bending Transducers

A resonant piezoelectric active-valve pump driven by the serial connected there-chambers is proposed based on three sandwich bending transducers (SBTs). The pump possesses the superiorities of high bandwidth and high output power. The configuration and driving principle of the pump are designed and studied. The wet modal and frequency response analyses are performed to determine the resonant frequency and output displacement, and their consistencies are also evaluated. The multi-physical field coupling model of the pump is established by bi-directional fluid structure interaction. The influences of frequency and outlet pressure of the pump on flowrate characteristics at different voltages are revealed. A physical prototype of the pump is manufactured and the tested setup is constructed to measure the output performances. This work shows that the maximum flowrate of the pump is 345 mL/min at 1.95 kHz; the maximum pressure can reach up to 242 kPa at 2.05 kHz. Besides, the self-filling pressure is 78 kPa; and the maximum driving power is 432 mW with an outlet pressure of 125 kPa. The results show that the developed pump is expected to be used in the hydraulic drive system of UAV variable swept wing.

Analysis of Induction Based Wireless Power Transfer Scheme

Abstract: Wireless power transfer scheme has become quite popular in recent times and used in various applications including consumer electronics, and electrical vehicle chargers. Although the power transfer scheme based on magnetic induction is knowledge, the relationship between efficiency of power transfer scheme with the ferrite core cross sectional area is not well understood. Surfaces with symmetrical ferrite core cross section area, will have good magnetic coupling while unsymmetrical cross-sectional surfaces with smaller overlap of magnetic flux, will suffer from high leakage inductance and excessive losses. Since majority of the wireless charging applications use non-uniform magnetic surfaces, the efficiency of real power transfer across primary and secondary windings tends to be lower and will require additional compensating circuitry or complex control algorithm. Unless a thorough understanding of leakage inductance is performed, wireless power topology will suffer from excessive resonant power circulation and output regulation will become unstable. Compensating circuit added at the secondary output can decrease overall reliability and increase BOM (Bill of material) cost. In this paper, wireless power transfer scheme is reviewed, and a theoretical model is provided. Analysis will be presented for various leakage inductances including the impact of operating frequency and line/load conditions

Nonlinear Dynamics and Energy Harvesting of a Two-Degrees-of-Freedom Electromagnetic Energy Harvester near the Primary and Secondary Resonances

Energy harvesting is a useful technique for various kinds of self-powered electronic devices and systems as well as Internet of Things technology. This study presents a two-degrees-of-freedom (2DOF) electromagnetic energy harvester that can use environment vibration and provide energy for small electronic devices. The proposed harvester consists of a cylindrical tube with two moving magnets suspended by a magnetic spring mechanism and a stationary coil. In order to verify the theoretical model, a prototype electromagnetic harvester was constructed and tested. The influence of key parameters, including excitation acceleration, response to a harmonic frequency sweep, and electromechanical coupling on the generated characteristics of the harvester, was investigated. The experimental and theoretical results showed that the proposed electromagnetic energy harvester was able to increase the resonance bandwidth (60–1200 rad/s) and output power (0.2 W). However, due to strong nonlinearity, an unstable region occurred near the main first resonance, which resulted from the Neimark–Sacker bifurcation.

Trajectory-Switching-Modulation-Based Fast Power Transient Control Strategy for a Bidirectional Hybrid Modular DC Transformer

The hybrid modular DC transformer (HMDCT) combining the series resonant dual active bridge (SR-DAB) and phase-shift dual active bridge (PS-DAB) has the advantages of high efficiency and bidirectional power regulation. However, due to the unregulated SR-DAB resonant tank inertia and limited PS-DAB output power, the dynamic response of HMDCT is slower than the pure PS-DAB based DC transformer, which could lead to a larger output overshoot. To address the problems, first, a novel trajectory-switching-modulation (TSM) method is proposed to control the SR-DAB resonant tank to track the desired state-trajectory rapidly by using SR-DAB switch-states. Compared with the conventional LLC trajectory control, TSM is more suitable for the SR-DAB in the bidirectional HMDCT because TSM is available under bidirectional power flow without changing the topology or increasing magnetizing losses. Then, a TSM based fast power transients control strategy is proposed to improve the bidirectional HMDCT dynamic performance by controlling the PS-DAB and SR-DAB simultaneously. Besides, PS-DAB current stress can also be reduced during the load transients. Experimental results show that the proposed strategy has better dynamic performance than the classic proportional-integral feedforward based strategy.

Multidirectional Piezoelectric Vibration Energy Harvester Based on Cam Rotor Mechanism.

The techniques that harvest mechanical energy from low-frequency, multidirectional environmental vibrations have been considered a promising strategy to implement a sustainable power source for wireless sensor networks and the Internet of Things. However, the obvious inconsistency in the output voltage and operating frequency among different directions may bring a hindrance to energy management. To address this issue, this paper reports a cam-rotor-based approach for a multidirectional piezoelectric vibration energy harvester. The cam rotor can transform vertical excitation into a reciprocating circular motion, producing a dynamic centrifugal acceleration to excite the piezoelectric beam. The same beam group is utilized when harvesting vertical and horizontal vibrations. Therefore, the proposed harvester reveals similar characterization in its resonant frequency and output voltage at different working directions. The structure design and modeling, device prototyping and experimental validation are conducted. The results show that the proposed harvester can produce a peak voltage of up to 42.4 V under a 0.2 g acceleration with a favorable power of 0.52 mW, and the resonant frequency for each operating direction is stable at around 3.7 Hz. Practical applications in lighting up LEDs and powering a WSN system demonstrate the promising potential of the proposed approach in capturing energy from ambient vibrations to construct self-powered engineering systems for structural health monitoring, environmental measuring, etc.