Parasitic Resistance Research Articles

Innovative Ethanol Sensors Utilizing Organic Material Patterned Surface Acoustic Wave Detection

In this paper, sensor based on surface acoustic waves for ethanol vapors detection, was fabricated and studied. For room temperature detection of the volatile compound, a novel carbyne nanofilm was deposited on the surface of a SAW transducer. The conventional electrodes were replaced by conductive polymeric coting of poly(3,4-ethylenedioxythiophene):poly (styrenesulfonate) (PEDOT:PSS) to minimize the microstructural and elemental difference between the electrode and gas sensitive material. The experimental results showed that the sensors had a good response to ethanol at room temperature. The maximum response of the sensors was at 600 ppm, where the time delay between the output and the input signals of the transducer was ~ 160 μs. The parasitic contact resistance and interface capacitance were found insufficient to affect the accuracy of the measurement, although their values are higher as compared to the sensors with metal electrodes.

Faecal egg count reduction tests and nemabiome analysis reveal high frequency of multi-resistant parasites on sheep farms in north-east Germany involving multiple strongyle parasite species

Anthelmintic resistance in sheep parasitic gastrointestinal nematodes is widespread and a severe health and economic issue but prevalence of resistance and involved parasite species are unknown in Germany. Here, the faecal egg count reduction test (FECRT) was performed on eight farms using fenbendazole, ivermectin and moxidectin and on four farms using only moxidectin. A questionnaire was used to obtain data on management practices to potentially identify risk factors for presence of resistance. All requirements of the recently revised WAAVP guideline for diagnosing anthelmintic resistance using the FECRT were applied. Nematode species composition in pre- and post-treatment samples was analysed with the nemabiome approach. Using the eggCounts statistic package, resistance against fenbendazole, ivermectin and moxidectin was found on 7/8, 8/8 and 8/12 farms, respectively. No formal risk factor analysis was conducted since resistance was present on most farms. Comparison with the bayescount R package results revealed substantial agreement between methods (Cohen's κ = 0.774). In contrast, interpretation of data comparing revised and original WAAVP guidelines resulted in moderate agreement (Cohen's κ = 0.444). The FECR for moxidectin was significantly higher than for ivermectin and fenbendazole. Nemabiome data identified 4 to 12 species in pre-treatment samples and treatments caused a small but significant decrease in species diversity (inverse Simpson index). Non-metric multidimensional scaling and k-means clustering were used to identify common patterns in pre- and post-treatment samples. However, post-treatment samples were scattered among the pre-treatment samples. Resistant parasite species differed between farms. In conclusion, the revised FECRT guideline allows robust detection of anthelmintic resistance. Resistance was widespread and involved multiple parasite species. Resistance against both drug classes on the same farm was common. Further studies including additional drugs (levamisole, monepantel, closantel) should combine sensitive FECRTs with nemabiome data to comprehensively characterise the anthelmintic susceptibility status of sheep nematodes in Germany.

98 Adding parasite resistance to the breeding objective in hair sheep

Abstract Economic selection indexes provide the best method to achieve genetic gain for multiple traits simultaneously. Hair sheep enterprises, particularly in environments with substantial gastrointestinal nematode challenge, may benefit from incorporating parasite resistance in a selection index. However, obtaining the relative economic value (REV) for parasite resistance is challenging; information on its impact on productivity is incomplete, as are the costs of treatment given anthelmintic resistance. The National Sheep Improvement Program (NSIP) currently provides producers with an index designed to increase total weight of lamb weaned per ewe lambing (TW). Our objective was to assess the effects of including fecal egg count, an indicator of parasite resistance, as an additional goal trait. Including the benchmark scenario with TW as its sole objective, 10 indexes were constructed using standard index theory. Post-weaning fecal egg count (PFEC) was added to this breeding objective with a REV of -1 and the REV for TW was varied from +1 to +5 at +0.5 increments. Weaning weight, number of lambs born and weaned, and PFEC were the selection criteria, modelled as either phenotypes or estimated breeding values (EBV). Phenotypes and EBV were simulated for 1,000 lambs by Cholesky decomposition and used to generate index scores. Ten replicates were run and the top 3% of males and 26% of females were retained on index scores. Annual responses in the goal traits were estimated. Responses in PFEC were expressed as a percentage, assuming a mean PFEC of 2,089 eggs/g as in NSIP. Concordances with those selected in the benchmark scenario were determined. Using EBV as selection criteria, TW increased by 1.7 kg/yr in the benchmark scenario (Table 1). However, unfavorably, PFEC increased by 2.3%/yr. When phenotypic criteria were used, TW increased by 0.5 kg/yr, and PFEC by 0.3%/yr. Once added to the breeding objective, PFEC decreased regardless of the REV of TW. However, response in TW also reduced, although less so as its REV increased. With EBV as the criteria, the REV of +3 for TW appeared preferable: PFEC reduced by 7.1%/yr with 98% of the response in TW retained. With phenotypic selection criteria, PFEC reduced by 5.2%/yr with 94% of the response in TW retained. With +3 REV for TW and EBV as the selection criteria, on average 65% and 82% of males and females, respectively, were chosen in common with the benchmark. When phenotypic criteria were used, those percentages were 60% and 80%, respectively. Implementing a more holistic index with REV of +3 for TW and -1 for PFEC would result in reasonable responses in both traits. However, producers will need to decide if reduced gains in TW is acceptable to improve parasite resistance in a hair sheep breeding program.

Impact of different mutations on Kelch13 protein levels, ART resistance, and fitness cost in Plasmodium falciparum parasites.

Parasites with lowered sensitivity to artemisinin-based drugs are becoming widespread. However, even in these "resistant" parasites not all parasites survive treatment. We found that the proportion of surviving parasites correlates with the fitness cost of resistance-inducing mutations which might indicate that the growth disadvantages prevents resistance levels where all parasites survive treatment. We also found that combining two common resistance mutations did not increase resistance levels. However, selection through repeated ART-exposure did, even-though the known resistance genes, including k13, were not further altered, suggesting other causes of increased resistance. We also observed a disproportionally high fitness cost of a resistance mutation in resistance gene ubp1. Such high fitness costs may explain why mutations in ubp1 and other genes functioning in the same pathway as k13 are rare. This highlights that k13 mutations are unique in their ability to cause resistance at a comparably low fitness cost.

High parasite diversity maintained after an alga-virus coevolutionary arms race.

Arms race dynamics are a common outcome of host-parasite coevolution. While they can theoretically be maintained indefinitely, realistic arms races are expected to be finite. Once an arms race has ended, for example due to the evolution of a generalist-resistant host, the system may transition into coevolutionary dynamics that favour long-term diversity. In microbial experiments, host-parasite arms races often transition into a stable coexistence of generalist-resistant hosts, (semi-)susceptible hosts, and parasites. While long-term host diversity is implicit in these cases, parasite diversity is usually overlooked. In this study, we examined parasite diversity after the end of an experimental arms race between a unicellular alga (Chlorella variabilis) and its lytic virus (PBCV-1). First, we isolated virus genotypes from multiple time points from two replicate microcosms. A time-shift experiment confirmed that the virus isolates had escalating host ranges, i.e., that arms races had occurred. We then examined the phenotypic and genetic diversity of virus isolates from the post-arms race phase. Post-arms race virus isolates had diverse host ranges, survival probabilities, and growth rates; they also clustered into distinct genetic groups. Importantly, host range diversity was maintained throughout the post-arms race phase, and the frequency of host range phenotypes fluctuated over time. We hypothesize that this dynamic polymorphism was maintained by a combination of fluctuating selection and demographic stochasticity. Together with previous work in prokaryotic systems, our results link experimental observations of arms races to natural observations of long-term host and parasite diversity.

Photovoltaic efficacy of CNGS as BSF and second absorber for CIGS thin film solar cells- numerical approach by SCAPS-1D framework

Solar cells based on CIGS have outperformed many thin film solar cells using other absorbers. A prospective CIGS active layer-based SC with an ITO/CdS/CIGS/CNGS hetero-structure, with a CdS buffer layer, ITO window layer, and CNGS in dual role: as extra absorber layer, and Back Surface Field (BSF) was suggested in this article. Through the utilization of the unidimensionnal simulation program (SCAPS-1D), the impacts of the absorbers densities of doping and thicknesses, interfacial defects, parasitic resistances, and working temperature on the device have been thoroughly examined. By exploring simulation results, excellent PV metrics, including 1.21 V, 32.25 mA/cm2, 75.08 %, and 29.39 % for Voc,Jsc,FF,andPCE are provided. The suggested hetero-structure based on CIGS, when simulated, offers a useful technique to create new solar cells with more performance than previously published devices.

The impact of CBz-PAI interlayer in various HTL-based flexible perovskite solar cells: A drift-diffusion numerical study

In perovskite solar cells (PSCs), the charge carrier recombination obstacles mainly occur at the ETL/perovskite and HTL/perovskite interfaces, which play a decisive role in the solar cell performance. Therefore, this study aims to enhance the flexible PSC (FPSC) efficiency by adding the newly designed CBz-PAI-interlayer (simply CBz-PAI-IL) at the perovskite/HTL interface. In addition, substantial work has been carried out on five different HTLs (Se/Te–Cu2O, CuGaO2, V2O5, and CuSCN, including conventional Spiro-OMeTAD as a reference HTL with and without CBz-PAI-IL), using drift-diffusion simulation to find suitable FPSC design to attain the maximum PCE. Interestingly, PET/ITO/AZO/ZnO NWs/FACsPbBrI3/CBz-PAI/Se/Te–Cu2O/Au device architecture demonstrates the highest achievable power conversion efficiency (PCE) of 27.9 %. The findings of this study confirmed that the reference device (without IL) displays a large valence band edge (VBE)/highest occupied molecular orbital (HOMO) energy level misalignment compared to the modified interface device (with CBz-PAI-IL that reduces VBE/HOMO level mismatch) that eases the hole transport, simultaneously, it reduces the charge carrier recombinations at the interface, resulting in diminished Voc losses in the device. Furthermore, the influence of perovskite absorber thickness and defect density, parasitic resistances, and working temperature are systematically examined to govern the superior FPSC efficiency and concurrently understand the device physics.

Evaluation of Additive Manufacturing for Wireless Power Transfer Applications

Additive Manufacturing (AM) has emerged as an economical and feasible technology for creating industrial components. This paper evaluates the use of AM for inductive Wireless Power Transfer (WPT) systems. In particular, the innovative use of metal 3D printing is proposed as a manufacturing process for the coils. For this reason, the recent improvement of metal AM is proposed as a suitable solution to increase design opportunities, reduce costs and production time while improving transmission efficiency. In fact, the WPT coil current distribution can be preliminarily studied through Finite Element Analysis (FEA) to optimize its cross-section and geometry. In this work, a general design procedure for WPT coils using metal AM is presented and this technology is compared with traditional solutions (i.e. hollow and litz wire) through extensive experimental measurements. The analysis shows that AM allows to reduce the parasitic resistance, costs and weight while increasing the transmission efficiency. Thus, the obtained results confirm the potential of AM for producing WPT coils, nominating this technology as a flexible, sustainable, and rapid solution for custom WPT coils production.

Study on adjustable low-frequency sound absorbers based on digital shunt loudspeakers

Low-frequency noise is a critical frequency band that affects people’s physical and mental health. Traditional sound absorption technology is limited in effectiveness at low frequencies due to spatial constraints. Shunt loudspeakers, which consist of a loudspeaker connected to a shunt circuit, have emerged as a rapidly developing solution for low-frequency noise control. However, most shunt circuits are implemented using analog circuits, resulting in poor stability and accuracy due to the presence of parasitic resistance. As a result of this situation, this paper proposes an adjustable low-frequency sound absorber based on digital shunt loudspeakers, where the shunt circuit is realized through digital synthetic impedance based on FPGA technology. Additionally, the acoustic impedance can be easily adjusted by the digital shunt circuit without relying on cavity depth adjustments. Experimental results validate that the proposed sound absorber offers excellent performance in adjustable low-frequency sound absorption, thus confirming its theoretical basis.

Access to quality-assured artemisinin-based combination therapy and associated factors among clients of selected private drug outlets in Uganda

BackgroundMalaria treatment in sub-Saharan Africa is faced with challenges including unreliable supply of efficacious agents, substandard medicines coupled with high price of artemisinin-based combinations. This affects access to effective treatment increasing risk of malaria parasite resistance development and adverse drug events. This study investigated access to quality-assured artemisinin-based combination therapy (QAACT) medicines among clients of selected private drug-outlets in Uganda.MethodsThis was a cross sectional study where exit interviews were conducted among clients of private drug outlets in low and high malaria transmission settings in Uganda. This study adapted the World Health Organization/Health Action International (WHO/HAI) standardized criteria. Data was collected using a validated questionnaire. Data entry screen with checks was created in Epi-data ver 4.2 software and data entered in duplicate. Data was transferred to STATA ver 14.0 and cleaned prior to analysis. The analysis was done at 95% level of significance.ResultsA total of 1114 exit interviews were conducted among systematically sampled drug outlet clients. Over half, 54.9% (611/1114) of the participants were males. Majority, 97.2% (1083/1114) purchased an artemisinin-based combination anti-malarial. Most, 55.5% (618/1114) of the participants had a laboratory diagnosis of malaria. Majority, 77.9% (868/1114) of the participants obtained anti-malarial agents without a prescription. Less than a third, 27.7% (309/1114) of the participants obtained a QAACT. Of the participants who obtained QAACT, more than half 56.9% (173/309) reported finding the medicine expensive. The predictors of accessing a QAACT anti-malarial among drug outlet clients include type of drug outlet visited (aPR = 0.74; 95%CI 0.6, 0.91), not obtaining full dose (3-day treatment) of ACT (aPR = 0.49; 95%CI 0.33, 0.73), not finding the ACT expensive (aPR = 1.24; 95%CI 1.03, 1.49), post-primary education (aPR = 1.29; 95%CI 1.07,1.56), business occupation (aPR = 1.24; 95%CI 1.02,1.50) and not having a prescription (aPR = 0.76; 95%CI 0.63, 0.92).ConclusionLess than a third of the private drug outlet clients obtained a QAACT for management of malaria symptoms. Individuals who did not find artemisinin-based combinations to be expensive were more likely to obtain a QAACT anti-malarial. The Ministry of Health needs to conduct regular surveillance to monitor accessibility of QAACT anti-malarial agents under the current private sector copayment mechanism.

Synthesizing environmental, epidemiological and vector and parasite genetic data to assist decision making for disease elimination.

We present a framework for identifying when conditions are favourable for transmission of vector-borne diseases between communities by incorporating predicted disease prevalence mapping with landscape analysis of sociological, environmental and host/parasite genetic data. We explored the relationship between environmental features and gene flow of a filarial parasite of humans, Onchocerca volvulus, and its vector, blackflies in the genus Simulium. We generated a baseline microfilarial prevalence map from point estimates from 47 locations in the ecological transition separating the savannah and forest in Ghana, where transmission of O. volvulus persists despite onchocerciasis control efforts. We generated movement suitability maps based on environmental correlates with mitochondrial population structure of 164 parasites from 15 communities and 93 vectors from only four sampling sites, and compared these to the baseline prevalence map. Parasite genetic distance between sampling locations was significantly associated with elevation (r = .793, p = .005) and soil moisture (r = .507, p = .002), while vector genetic distance was associated with soil moisture (r = .788, p = .0417) and precipitation (r = .835, p = .0417). The correlation between baseline prevalence and parasite resistance surface maps was stronger than that between prevalence and vector resistance surface maps. The centre of the study area had high prevalence and suitability for parasite and vector gene flow, potentially contributing to persistent transmission and suggesting the importance of re-evaluating transmission zone boundaries. With suitably dense sampling, this framework can help delineate transmission zones for onchocerciasis and would be translatable to other vector-borne diseases.

Metalloenzyme Inhibitors against Zoonotic Infections: Focus on Leishmania and Schistosoma.

The term "zoonosis" denotes diseases transmissible among vertebrate animals and humans. These diseases constitute a significant public health challenge, comprising 61% of human pathogens and causing an estimated 2.7 million deaths annually. Zoonoses not only affect human health but also impact animal welfare and economic stability, particularly in low- and middle-income nations. Leishmaniasis and schistosomiasis are two important neglected tropical diseases with a high prevalence in tropical and subtropical areas, imposing significant burdens on affected regions. Schistosomiasis, particularly rampant in sub-Saharan Africa, lacks alternative treatments to praziquantel, prompting concerns regarding parasite resistance. Similarly, leishmaniasis poses challenges with unsatisfactory treatments, urging the development of novel therapeutic strategies. Effective prevention demands a One Health approach, integrating diverse disciplines to enhance diagnostics and develop safer drugs. Metalloenzymes, involved in parasite biology and critical in different biological pathways, emerged in the last few years as useful drug targets for the treatment of human diseases. Herein we have reviewed recent reports on the discovery of inhibitors of metalloenzymes associated with zoonotic diseases like histone deacetylases (HDACs), carbonic anhydrase (CA), arginase, and heme-dependent enzymes.

Urgent action is needed to confront artemisinin partial resistance in African malaria parasites.

Urgent action is needed to confront artemisinin partial resistance in African malaria parasites.

Development of methods to analyse Plasmodium falciparum single nucleotide polymorphisms in PfCRT (А > C), PfMDR1 (A > T) and PfDHFR (G > A) genes that determine resistance to quinoline, diamino-pyrimidine and sulfonamide groups of antimalarial drugs

BACKGROUND: The drug resistance of tropical malaria pathogens to mefloquine, chloroquine, pyrimethamine and their derivatives is associated with three single nucleotide polymorphisms: K76T (A403627C), S1034C (A960989T) and S108N (G748410A). These mutations are linked to changes in the structure of the PfCRT and PfMDR1 genes of Plasmodium falciparum.
 AIM: Develop methods for identifying single nucleotide polymorphisms that are suitable for early diagnosis of drug-resistant forms of tropical malaria.
 RESULTS: A method was developed based on restriction fragment length analysis using ApoI endonuclease to detect the K76T polymorphism (A403627C). The criterion for determining parasite resistance to chloroquine was the appearance of a single 145 bp band on the electropherogram. The genotype of the pathogens remained unchanged and their drug sensitivity was preserved, as indicated by the separation of two fragments of 98 and 47 bp.
 A system for detecting S108N (G748410A) was developed using the Bse1I endonuclease. The appearance of a single 507 bp band on the electropherogram indicated the mutant genotype of the pathogens, while the appearance of two fragments (323 and 184 bp) indicated an unchanged genotype and preservation of drug sensitivity of plasmodiae.
 To identify the A T polymorphism in the PfMDR1 gene at position 960989, polymerase chain reaction technology will be used with two allele-specific primers. One primer will detect the wild-type allele, and the other will detect the mutant genotype. The amplifiable fragment of the PfMDR1 gene contains sequences of the 1034th codon. Depending on the P. falciparum genotype, 261 bp fragments will be obtained with one of the allele-specific primers.
 CONCLUSION: Criteria for assessing drug resistance of P. falciparum were developed based on the analysis of obtained data. Haplotypes K76T (band 145 bp) and S1034C (band 262 bp with the direct primer S1034C-F2) serve as indicators of the relative resistance of pathogens to chloroquine, mefloquine, and their derivatives. Positive results of examination for haplotype S108N (bands 323 and 184 bp) should be considered as a sign of decreased sensitivity to pyrimethamine. The developed methods can be used in clinical practice and for epidemiological monitoring.

Optimizing Ultrathin 2D Transistors for Monolithic 3D Integration: A Study on Directly Grown Nanocrystalline Interconnects and Buried Contacts.

The potential of monolithic 3D integration technology is largely dependent on the enhancement of interconnect characteristics which can lead to thinner stacks, better heat dissipation, and reduced signal delays. Carbon materials such as graphene, characterized by sp2 hybridized carbons, are promising candidates for future interconnects due to their exceptional electrical, thermal conductivity and resistance to electromigration. However, a significant challenge lies in achieving low contact resistance between extremely thin semiconductor channels and graphitic materials. To address this issue, an innovative wafer-scale synthesis approach is proposed that enables low contact resistance between dry-transferred 2D semiconductors and the as-grown nanocrystalline graphitic interconnects. A hybrid graphitic interconnect with metal doping reduces the sheet resistance by 84% compared to an equivalent thickness metal film. Furthermore, the introduction of a buried graphitic contact results in a contact resistance that is 17 times lower than that of bulk metal contacts (>40nm). Transistors with this optimal structure are used to successfully demonstrate a simple logic function. The thickness of active layer is maintained within sub-7nm range, encompassing both channels and contacts. The ultrathin transistor and interconnect stack developed here, characterized by a readily etchable interlayer and low parasitic resistance, leads to heterogeneous integration of future 3D integrated circuits (ICs).

Study of optical float-zone grown gallium oxide Schottky barrier diode

β−Ga2O3 based lateral Schottky barrier diodes are fabricated using Ni/Au as Schottky contact and Ti/Au as Ohmic contact. The Sn-doped β−Ga2O3 sample is grown by the optical float-zone technique. The effect of trenches, which are used for mesa isolation, on breakdown voltage is investigated. The device shows near-ideal characteristics in terms of built-in potential. The parasitic series and shunt resistances are extracted, and their dependency on temperature is established. Modeling of temperature-dependent reverse leakage current is demonstrated using the thermionic emission model, Poole–Frenkel emission model, and Fowler-Nordheim tunneling mechanism. The procedure to extract relevant parameters is explained in terms of bias and temperature dependency. The combined model shows excellent agreement with experimental data over a wide range of bias and temperature. The maximum electric field of 2.3 MV cm−1 is achieved.

Overview of Research on Leishmaniasis in Africa: Current Status, Diagnosis, Therapeutics, and Recent Advances Using By-Products of the Sargassaceae Family.

Leishmaniasis in Africa, which has been designated as a priority neglected tropical disease by various global organizations, exerts its impact on millions of individuals, primarily concentrated within this particular region of the world. As a result of the progressively grave epidemiological data, numerous governmental sectors and civil organizations have concentrated their endeavors on this widespread outbreak with the objective of devising appropriate remedies. This comprehensive examination delves into multiple facets of this parasitic ailment, scrutinizing the associated perils, diagnostic intricacies, and deficiencies within the existing therapeutic protocols. Despite the established efficacy of current treatments, they are not immune to deleterious incidents, particularly concerning toxicity and the emergence of parasitic resistance, thus accentuating the necessity of exploring alternative avenues. Consequently, this research not only encompasses conventional therapeutic approaches, but also extends its scope to encompass complementary and alternative medicinal techniques, thereby striving to identify innovative solutions. A particularly auspicious dimension of this study lies in the exploration of natural substances and by-products derived from some brown algae of the Sargassaceae family. These resources possess the potential to assume a pivotal role in the management of leishmaniasis.

Exploring the modulatory influence on the antimalarial activity of amodiaquine using scaffold hybridisation with ferrocene integration

Amodiaquine (AQ) is a potent antimalarial drug used in combination with artesunate as part of artemisinin-based combination therapies (ACTs) for malarial treatment. Due to the rising emergence of resistant malaria parasites, some of which have been reported for ACT, the usefulness of AQ as an efficacious therapeutic drug is threatened. Employing the organometallic hybridisation approach, which has been shown to restore the antimalarial activity of chloroquine in the form of an organometallic hybrid clinical candidate ferroquine (FQ), the present study utilises this strategy to modulate the biological performance of AQ by incorporating ferrocene. Presently, we have conceptualised ferrocenyl AQ derivatives and have developed facile, practical routes for their synthesis. A tailored library of AQ derivatives was assembled and their antimalarial activity evaluated against chemosensitive (NF54) and multidrug-resistant (K1) strains of the malaria parasite, Plasmodium falciparum. The compounds generally showed enhanced or comparable activities to those of the reference clinical drugs chloroquine and AQ, against both strains, with higher selectivity for the sensitive phenotype, mostly in the double-digit nanomolar IC50 range. Moreover, representative compounds from this series show the potential to block malaria transmission by inhibiting the growth of stage II/III and V gametocytes in vitro. Preliminary mechanistic insights also revealed hemozoin inhibition as a potential mode of action.

A Theileria annulata parasite with a single mutation, methionine 128 to isoleucine (M128I), in cytochrome B is resistant to buparvaquone.

Tropical theileriosis is a fatal leukemic-like disease of cattle caused by the tick-transmitted protozoan parasite Theileria annulata. The economics of cattle meat and milk production is severely affected by theileriosis in endemic areas. The hydroxynaphtoquinone buparvaquone (BPQ) is the only available drug currently used to treat clinical theileriosis, whilst BPQ resistance is emerging and spreading in endemic areas. Here, we chronically exposed T. annulata-transformed macrophages in vitro to BPQ and monitored the emergence of drug-resistant parasites. Surviving parasites revealed a significant increase in BPQ IC50 compared to the wild type parasites. Drug resistant parasites from two independent cloned lines had an identical single mutation, M128I, in the gene coding for T. annulata cytochrome B (Tacytb). This in vitro generated mutation has not been reported in resistant field isolates previously, but is reminiscent of the methionine to isoleucine mutation in atovaquone-resistant Plasmodium and Babesia. The M128I mutation did not appear to exert any deleterious effect on parasite fitness (proliferation and differentiation to merozoites). To gain insight into whether drug-resistance could have resulted from altered drug binding to TaCytB we generated in silico a 3D-model of wild type TaCytB and docked BPQ to the predicted 3D-structure. Potential binding sites cluster in four areas of the protein structure including the Q01 site. The bound drug in the Q01 site is expected to pack against an alpha helix, which included M128, suggesting that the change in amino acid in this position may alter drug-binding. The in vitro generated BPQ resistant T. annulata is a useful tool to determine the contribution of the various predicted docking sites to BPQ resistance and will also allow testing novel drugs against theileriosis for their potential to overcome BPQ resistance.

Characterization of drug resistance genes in Indian Plasmodium falciparum and Plasmodium vivax field isolates

One of the major challenges for malaria control and elimination is the spread and emergence of antimalarial drug resistance. Mutations in Plasmodium falciparum (Pf) and Plasmodium vivax (Pv) field isolates for five drug resistance genes viz. crt, mdr1, dhps, dhfr and kelch known to confer resistance to choloroquine (CQ), sulfadoxine-pyrimethamine (SP) and artemisinin (ART) and its derivatives were analyzed. A total of 342 symptomatic isolates of P. falciparum (Pf) and P. vivax (Pv) from 1993 to 2014 were retrieved from malaria parasite repository at National Institute of Malaria Research (NIMR). Sample DNA was extracted from dried blood spots and various targeted single nucleotide polymorphisms (SNPs) associated with antimalarial drug resistance were analysed for these isolates. 72S (67.7%) and 76T (83.8%) mutations along with SVMNT haplotype (67.7%) predominated the study population for Pfcrt. The most prevalent SNPs were 108N (73.2%) and 437G (24.8%) and the most prevalent haplotypes were ACNRNI (51.9%) and SAKAA (74.5%) in Pfdhfr and Pfdhps respectively. Only two mutations in Pfmdr1, 86Y (26.31%) and 184F (56.26%), were seen frequently in our study population. No mutations associated with Pfk13 were observed. For Pv, all the studied isolates showed two Pvdhps mutations, 383G and 553G, and two Pfdhfr mutations, 58R and 117N. Similarly, three mutations, viz. 958M, 908L and 1076L were found in Pvmdr1. No variations were observed in Pvcrt-o and Pvk12 genes. Overall, our study demonstrates an increase in mutations associated with SP resistance in both Pf and Pv, however, no single nucleotide polymorphisms (SNPs) associated with ART resistance have been observed for either species. Various SNPs associated with CQ resistance were seen in Pf; whereas only Pvmdr1 associated resistant SNPs were observed in Pv. Therefore, molecular characterization of drug resistance genes is essential for timely monitoring and prevention of malaria by identifying the circulating drug resistant parasites in the country.