Discharge Regime Research Articles

Streamer dynamics and periodical discharge regime transitions under repetitive nanosecond pulses with airflow

Although the nanosecond repetitively pulsed (NRP) discharge normally stabilizes into one of three regimes (corona/glow/spark) in a pulse train, another nonintuitive instability recently proved that it could periodically swing between corona and spark regimes characterized by repeated spark quenches and reestablishments (Zhao et al 2022 Plasma Sources Sci. Technol. 31 045005). In this paper, we have further investigated the suitability of NRP discharge regime transitions for different pulsed power supplies and revealed dramatic effects of the gas flow on streamer dynamics that possibly lead to spark quenches. Pulse-sequence and temporally resolved electrical and optical diagnostics were implemented to capture discharge evolutions in long pulse trains. Periodical discharge regime transitions under long-term repetitive nanosecond pulses are prevalent under a transmission line transformer pulser and a commercially available FID pulser with parameter constraints. A minimum deposited energy per spark is required for the successive spark pattern. The spark channel before its quench statistically prefers to deviate upstream rather than following the straight axis or intuitively bending downstream to search for more remnants. Before spark quenches, the initial streamer already either exhibits a large radial ‘detour’ or propagates with a zig-zag profile along the periphery of previous spark regions. The periodical discharge regime transition and effects of the gas flow are qualitatively explained based on the plasma–source coupling, evolutions of dominant negative ion composition, and 3D streamer simulation. Periodical NRP spark quenches are probably initiated with the streamer ‘detour’ and then accelerated by the thermal-ionization feedback instability. Inhomogeneous residual charge distribution and accumulations of complex negative ions with high electron bound energies may facilitate the following discharge to search for the gas inlet. In-depth understanding of NRP discharge instabilities could be reached, which are fundamentally governed by residual charge transport and energy relaxation.

Investigation on plasma enhanced decomposition of ammonium dinitramide (ADN) based propellant with optical diagnosis

Plasma-enhanced decomposition is a promising method to achieve reliable ignition and better thruster performance with an ADN-based propellant. High-speed imaging and optical emission spectroscopy are used to characterize the discharge plasma produced from ADN-based propellant vapor and argon carrier gas within parallel planes. Discharge regimes are independently controlled by varying working parameters. The transition from abnormal glow discharge (AGD) to filamentary discharge (FD) is identified from voltage-current characteristics and sudden changes in excitation electron temperature (Te-exc) and electron density (Ne) under a pressure of 0.2–10 kPa. Instabilities develop because there are more freedom degrees and higher collision probabilities after ADN-based propellant vapor is added. The product of Te-exc and Ne shows a higher energy transfer efficiency from input power to vapor in the FD regime. Water molecules increase the net dissociative attachment rate and effectively quench Ne. Although preheated vapor (as the discharge medium) has a much lower Ne, more radicals appear such as OH, NH, CH, CN, N2, N2+, and C2, which promote chemical interactions in an electric field and increase the probability of successful ignition. This can be attributed to thermalization due to an increase in the translational kinetic energy and rotational excitation, which has an important impact on chemical reaction kinetics. Therefore, preheating is verified as critical for improving the ignition and performance of a plasma-assisted ADN-based thruster.

Study of Rod-Plate DC Discharge Plasma Characteristics at Atmospheric-Pressure

The characteristics of atmospheric-pressure glow discharge (APGD) produced by rod-plate electrodes are experimentally determined. APGD is sustained by applying a high DC voltage between the electrodes. At atmospheric pressure, the shift from corona discharge to glow discharge is investigated. A rod-plate discharges configuration's volt–ampere properties show the existence of three discharge regimes: corona, glow, and spark. The variations in the electrical field distribution in the various regimes are mirrored in the discharge luminosity. The rod-plate patterns are created under a dark region, and are visible mainly due to the effect of electrons heated by the local enhanced electric field at the interface, according to the optical emission spectra of the entire discharge.

Mechanisms of bar adjustments in the Jingjiang Reach of the Yangtze River in response to the operation of the Three Gorges Dam

Dams alter downstream river flow and sediment regimes, causing significant changes in river morphologies. The middle Yangtze River downstream of the Three Gorges Dam (TGD) has experienced rapid erosion in recent years, and the associated morphodynamic changes have negatively impacted the riverbank stability, navigation waterways and ecological functioning. Earlier studies have analyzed recent channel adjustments in the Yangtze River; however, our understanding of changes in the bar morphodynamics remains incomplete. In this study, we collected and analyzed flow and sediment data (1991–2016) and river bathymetry data (1975–2017) and investigated the mechanisms of bar adjustments along the Jingjiang Reach in the post-TGD period. The results indicate that most steady bars with a higher elevation and better vegetation coverage have experienced lateral erosion, while their elevations have remained stable overall. The unvegetated migrating bars with a lower elevation have experienced severe surficial erosion and area shrinkages. A new assessment method of the dominant discharge range on downstream bars is provided after dam closure. The dominant discharge range that determines bar adjustments corresponds to the flow stages between the submersion of migrating bars (∼12,500 m3/s) and the overtopping of vegetated steady bars (∼27,500 m3/s) in the Jingjiang Reach. A quantitative relationship exists between bar erosion in response to changed dominant discharge regimes and sediment decline. The significant bar erosion after the operation of the TGD can be attributed to the increased flow duration and the sharp decline in the suspended sediment concentration (SSC) of the dominant discharge range, and changes in SSCs play a primary role. The bar area will decrease by ∼0.003 km2 when the annual cumulative duration of the dominant discharge increases by one day and by ∼0.234 km2 when the annual average SSC of the dominant discharge decreases by 0.01 kg/m3. Furthermore, vegetation encroachment and colonization play a positive role in stabilizing bar morphologies and limiting surficial erosion, whereas vegetation soley cannot prevent the lateral erosion of steady bars. These findings suggest that multiple controls of discharge, sediment and vegetation on the evolution of fluvial bars and have important implications for river management and ecological evaluation in response to the operation of large dams.

Integrated hydro informatics tool to assess hydrological alteration on gauged sites: Hydra-Eflow

The alterations in the hydrosphere dynamics are undeniable. However, the analysis of hydrological alterations provides a benchmark to identify the potential environmental consequences and triggers of the evinced deviations. Hydra-Eflow is a free download and integrated hydro-informatics tool to assess gauged site discharge timeseries deviations for two non-concomitant samples through the Hydrologic Alteration Indices on Rivers (IAHRIS, acronym in Spanish). Its modules allow data quality verification, traditional frequency analysis, alteration analysis, and desktop environmental flow prescription. In addition, Hydra-Eflow supplies recommendations by an expert-based adjacency matrix to guide forward cascading studies and provide helpful rules for robust models. A case study at the Balsas River Basin is shown to verify the consistency of the information generated by Hydra-Eflow. Results show that 96 out of 129 hydrometric stations are altered due to changes in the discharge regime derived from the densified number of dams and impoundments in the streams for a wide range of purposes. Furthermore, the middle northern sub-basins exhibit a high alteration degree which may cause appalling water resources management since they submit more than 25% of the drinking water consumed in Mexico City. Finally, Hydra-Eflow supplied information to improve the heuristics of hydrologic alteration in the Balsas River Basin.

Development of a 50-A heaterless hollow cathode for electric thrusters.

Hollow cathodes in electric thrusters normally use an external heater to raise the thermionic electron emitter to emission temperatures. These heaters are a potential single-point failure in the thruster and add a separate power supply to the power processing unit. Heaterless hollow cathodes are attractive for their compact size and potential higher reliability but have only been reliably demonstrated to date in small hollow cathodes capable of discharge currents below around 5A. A new heaterless LaB6 hollow cathode has been developed that is capable of discharge currents from 5 to 50A. The cathode configuration extends the gas feed tube at cathode potential part way into the emitting insert region of the cathode. A high-voltage Paschen discharge is struck from the tube to the keeper that heats the tube tip, which then efficiently heats the insert by radiation. This configuration eliminates the arcing observed in prior large heaterless designs that coupled the high-voltage Paschen discharge to the orifice plate or the insert itself. Discharge current-voltage characteristics show that the presence of the tube does not significantly perturb the insert-region plasma. Startup uses a simple 3minignition procedure, and voltage traces of the keeper discharge reveal that much of the present tube-radiator's 100-to-150W heating power comes from an intermediate thermionic discharge sustained by the tube during the transition between the Paschen discharge and LaB6 insert thermionic regime. This novel heating mechanism enables an unprecedented class of higher-current heaterless hollow cathodes for the next generation of high-power electric propulsion systems.

Nanosecond pulsed discharge dynamics during passage of a transient laminar flame

This work presents an experimental study of a nanosecond repetitively pulsed dielectric barrier discharge interacting with a transient laminar flame propagating in a channel of height near the quenching distance of the flame. The discharge and the flame are of comparable size, and the discharge is favoured at a location where it is coupled with the reaction zone and burnt gas. The primary goal is to determine how the discharge evolves on the time scale of the flame passage, with the evolution driven by the changing gas state produced by the moving flame front. This work complements the large body of work investigating the effect of plasma to modify flame dynamics, by considering the other side of the interaction (how the discharge is modified by the flame). The hot gas produced by the combustion had a strong effect on the discharge, with the discharge preferentially forming in the region of hot combustion products. The per-pulse energy deposited by the discharge was measured and found to increase with the size of the discharge region and applied voltage. The pulse repetition frequency did not have a direct impact on the per-pulse energy, but did have an effect on the morphology and size of the discharge region. Two distinct discharge regimes were observed: uniform and filamentary (microdischarges). Higher pulse repetition frequencies and faster-cooling combustion products were more likely to transition to the filamentary regime, while lower frequencies and slower-cooling combustion products maintained a uniform regime for the entirety of the time the discharge was active. This regime transition was influenced by the ratio of the time scale of fluid motion to the pulse repetition rate (with no noticeable impact caused by the reduced electric field), with the filamentary regime preferentially observed in situations where this ratio was small. This work demonstrates the importance of considering how the discharge properties will change due to combustion processes in applications utilizing plasma assistance for transient combustion systems.

Operating regimes of a constricted arc discharge in a forevacuum-pressure, plasma-cathode electron source of pulsed large-radius electron beams

We have investigated the operating regimes of a pulsed constricted arc discharge in a forevacuum plasma-cathode electron source of large-radius electron beams. The configuration of the intermediate electrode (IE) with a constricting channel (CC) determines the maximum parameters (current and pulse duration) and operating regimes of the constricted arc. An IE with ceramic (aluminum nitride) CC and an IE with sectional tantalum CC, formed by several electrically insulated tantalum disks with co-axial holes, lead to an increase in the maximum parameters compared to an IE with metal CC. In particular, an IE with sectional tantalum CC provides the highest maximum parameters. The ceramic and sectional tantalum constricting channels also provide lower minimum pressure for which the constricted arc operates stably. When the pressure reaches a certain threshold value, which depends on arc current, a discharge system with IE with sectional tantalum CC provides stable operation for pulse duration up to 10 ms. An increase in pressure provides higher discharge current in the millisecond regime of the discharge operation. When the arc current reaches threshold values from 84 to 92 A (depending on gas pressure), a self-compressed (pinched) mode of operation of the constricted arc occurs. The pinched arc regime is characterized by the highest current and the longest pulse duration. The forevacuum electron source based on the constricted arc discharge with IE with sectional tantalum CC offers generation of low-energy (up to 8 keV) electron beam with current up to tens of amperes and pulse duration up to 10 ms.

Influence of the dielectric thickness on the homogeneity of a diffuse dielectric barrier discharge in air

This work focuses on a diffuse Dielectric Barrier Discharge (DBD) in atmospheric pressure air using an original experimental approach. In air, the role of the capacitance on the discharge regime has not yet been studied even though it affects the discharge current. To address this gap in knowledge, the dielectric capacitance was modified by the means of the dielectric thickness in a plane-to-plane DBD configuration. The discharge regime was analyzed using short exposure time photographs and electrical measurements in order to remove any potential uncertainties regarding the diffuse nature of the DBD in atmospheric pressure air. The influence of the dielectric capacitance on the discharge regime was analyzed thanks to the working domain of the discharge. Additionally, using an original electrical model of the discharge, the effective surface and current density of the discharge was obtained only from electrical measurements. Thus, the crucial role of the maximum current density on the discharge regime was highlighted. The control of the current density by the means of the dielectric capacitance led to the obtention of a diffuse discharge at a frequency up to 5 kHz for the very first time. Considering this high frequency, the possibility of using a DBD in air at atmospheric pressure for coating applications is discussed.

Enhancement of thrust force of an atmospheric pressure positive corona discharge by DC superimposed AC high voltage

The ability of corona discharge as an electrohydrodynamic propulsion system has been considered by many physicists and aerospace researchers. The results show that the most important factor in increasing the thrust force and thrust effectiveness is increasing the momentum transmission frequency in other words reduction of ion mobility that leads to a reduction of the average velocity. By configuring the wire-cylinder in atmospheric conditions, in an experimental study, using a new strategy in generating corona discharge, and without changing the system configuration, the thrust force is increased by increased of exciting species and reducing the ion mobility. DC superimposed AC (AC-DC) voltage source was utilized to achieve higher thrust force efficiency. Results show that the thrust force generated by the AC-DC source is increased by 4–2 times, with the applied voltage range of 10–20 kV compared to the DC source, respectively; while the thrust effectiveness has also been increased. A theory is introduced to calculate the thrust force due to ionic wind generation in the corona discharge regime. Accordingly, a relation is obtained for calculating thrust force and ion mobility using the average vertical ionic wind velocity on the side of the grounded electrode to support experimental results.

Internal Resistance Analysis of Na/NiCl2 Cells using Electrochemical Impedance Spectroscopy

A pulsed discharge regime (GITT) was used to investigate the ohmic internal resistance of Na/NiCl2 cells, also known as ZEBRA Cells. Two ways were chosen to determine the internal resistance, on the one side the voltage response of the corresponding current enables a calculation. On the other side the potentiostatic electrochemical impedance spectroscopy (EIS) was used to measure cell spectra including the ohmic internal resistance. By comparing both methods the feasibility of ohmic internal resistance (IR) calculation can be evaluated. The cells were investigated within five different operating temperatures (300 °C–180 °C with 30 K steps). Results show that the ohmic internal resistance of a Na/NiCl2 is increasing when the operating temperature is decreasing, mainly due to the decrease of ionic conductivity of separator and the secondary electrolyte NaAlCl4. As a direct consequence, there is a significant capacity loss. Therefore, the operating temperature can be identified as capacity limiting factor.

Microgap breakdown with floating metal rod perturbations

We report the characterization of microgap breakdown with perturbations from a metal rod floating between anode and cathode electrodes. The effects of the metal rod on the electric field distribution and the field enhancement factor are evaluated by numerical simulation and the conformal mapping method, and they indicate that the field emission regime is not reached. The breakdown voltages in the Townsend discharge regime are determined based on the voltage–current characteristics, which are obtained from two-dimensional fluid simulations. It is found that the breakdown characteristics can be significantly modulated by the floating metal rod, and the breakdown curve (breakdown voltage vs the net gap distance) is no longer U-shaped, which deviates from the conventional Paschen's law. The underlying physical mechanisms are related to the electric field enhancement, curved breakdown path, and nonuniform ion flux caused by the electric shielding effect. The results provide insights into breakdown characteristics in microscale discharges, which may promote conventional investigation of simplified clean gaps toward more complex conditions (e.g., with floating microparticles) in miniaturized plasma devices.

Effects of inter-pulse coupling on nanosecond pulsed high frequency discharge ignition in a flowing mixture

This work numerically investigates the effects of non-equilibrium nanosecond plasma discharge pulse repetition frequency, pulse number, and flow velocity on the critical ignition volume, minimum ignition energy, and chemistry in a plasma-assisted H2/air flow at 300 K and 1 atm using a multi-scale adaptive reduced chemistry solver for plasma assisted combustion (MARCS-PAC). The interactions between discharges/ignition kernels spanning decoupled, partially-coupled and fully-coupled regimes in a pulse train are studied. For a single pulse discharge, increased flow velocity increases the minimum ignition energy required due to the increase of convective heat loss and flame stretch. The results show that the minimum ignition kernel propagation speed at the critical ignition kernel volume increases with the flow velocity. The minimum critical ignition volume decreases with the increase of plasma discharge energy. For sequential two-pulse discharges, ignition fails at both decoupled and partially-coupled regimes even when the total discharge energy is above the minimum ignition energy, but succeeds only in the fully-coupled regime at a shorter inter-pulse time. Overlap of the OH radical pool between the sequential two-pulse discharges and the increase of the chemistry effect due to the increase of reduced electric field in the fully-coupled regime contribute to the ignition enhancement. In addition, for two-pulse discharges in the fully-coupled discharge regime, the mixture can be ignited at a total energy below the minimum ignition energy of a single pulse with the same flow conditions. Moreover, for a given total discharge energy with multiple pulsed discharges, the enhancement of the ignition kernel volume has a non-monotonic dependence on discharge frequency and pulse number. The effective ignition enhancement can be achieved with an optimal pulse repetition frequency and pulse number. This work provides a new understanding of the mechanism for repetitive plasma ignition and insights for the optimization of plasma ignition in a reactive flow.

Spatial–temporal evolution of the pressure field generated by a plasma actuator in quiescent air

Dielectric barrier discharge plasma actuators, capable of generating quasi-steady wall jets, are well suited for flow control on various problems. Compared with the detail related to the induced velocity field, there are limited results available for the pressure field created by the plasma actuator. However, the profound merits of understanding the evolution of the pressure field are to reveal the controlling mechanism. Here, the time-averaged and the phase-averaged pressure field distributions are obtained by using a pressure reconstruction method based on the velocity field from particle image velocimetry experiments. According to the discharge regimes, the formation mechanism of the pressure field is discussed. During the streamer discharge stage, the pressure close to the upper electrode is decreased under the influence of the induced heating caused by the high-frequency and high-amplitude pulsed current, leading to the air above the plasma actuator being drawn toward the wall surface. During the glow discharge stage, under the effect of suction generated by the streamer discharge, the pressure near the wall is increased and the plasma actuator generates a favorable pressure gradient, which provides advantageous conditions for the airflow acceleration. During the discharge quenching stage, the effect of the plasma actuator vanishes and the influence of viscous force is strengthened. Therefore, the adverse pressure gradient is gradually formed and the velocity of the wall jet is decreased compared to that of the glow discharge stage. The change of pressure field in a period can be summarized into three processes: pressurization, pressure release, and pressure recovery.

Time evolution of plasma parameters in the jet of a low-power vacuum arc thruster

The plasma parameters temporal evolution of a 30 W-class Vacuum Arc Thruster equipped with a Ni-Cr cathode is examined in the far-field region of the plasma jet. Measurements have been performed 20 cm downstream of the arc region where the plasma is created. The thruster operated at 1 Hz with 25 μs duration current pulses. The maximum current intensity reaches 4000 A about 8 μs after the discharge ignition. The change in the electron density, electron temperature and plasma potential during the short high-current pulse has been obtained by means of time-resolved Langmuir probe measurements. A time-of-flight technique based on a planar probe has been used to determine the mean ion velocity in the plasma jet. In addition, a Faraday cup allowed the determination of the ion current density. The electron density peaks at ∼ 8×1017 m−3 at 12 μs. The electron temperature is above 25 eV at 7 μs and then it stabilizes around 5 eV. Several ion populations are identified. The lowest ion mean velocity amounts to 20 km/s. Interestingly, combining all data allows to assess the ion mean electrical charge and its temporal behavior. The mean charge reaches 12 a few μs after ignition. It decays quickly afterwards and stays unchanged at 2 beyond 10 μs. Analysis of all the results support the idea of two distinct plasma discharge regimes.

Effects of initial and boundary conditions on gravel-bed river morphology

Assuming that the equilibrium geometry of river channels does not depend on their initial state but solely on boundary conditions, several formulas have been derived that relate the channel depth and width to the river bankfull discharge and bed material. However, due to the existence of a threshold for sediment motion and the strong non-linearity between sediment transport and flow rate, this assumption might not be generally valid for gravel-bed rivers. This research clarifies the role of the initial conditions, more specifically the initial channel width, on the geometry of gravel-bed rivers considering a variety of boundary conditions. The approach includes laboratory experiments and two-dimensional modeling, reproducing the evolution of alluvial channels with different starting widths, discharge regimes and sediment input rates. The experiments represent the Arc River (France). Thus, the characteristics of this river were used in the numerical model to obtain a realistic virtual case complementing the experiments. Different boundary and starting conditions resulted in either braided or single-thread channels. We found that the initial width strongly influences the evolution process and leaves a footprint on the river braid-belt extension. The active width of braided systems and the width of single-thread channels do not depend on the starting condition. They depend on sediment input rather than on discharge variability. Different initial widths result in different final bed levels. This indicates that the initial channel width may affect the degree of channel incision or aggradation. The results of this study justify the use of equilibrium formulas for single-thread rivers.

Nanosecond-pulsed DBD plasma treatment on human leukaemia Jurkat cells and monoblastic U937 cells in vitro

Plasma therapy offers an exciting and novel way of cancer treatment. Specifically, it is shown that Jurkat death rates are closely governed by the plasma treatment time. However, apart from time, alterations to different parameters of treatment process may yield better results. Here, Dielectric barrier discharge (DBD) reactors excited by a nanosecond-pulse energy source are used to investigate cell viability for longer exposure times as well as the effects of polarity of reactor on treatment. Plasma discharge regimes are discussed and assessed using imaging and thermal imaging methods. We found that by changing the polarity of reactor i.e. changing the direction of plasma discharge, the plasma discharge regime changes influencing directly the effectiveness of treatment. Our results showed that ns-DBD− reactor could induce both apoptosis and necrosis of human Jurkat and U937 cells, and this cytotoxic effect of plasma was not completely antagonized by N-acetyl cysteine. It indicates that plasma could induce ROS-independent cell death. Gene expression analyses revealed that p53, BAD, BID and caspase 9 may play vital roles in plasma caused cell death. In addition, our findings demonstrate how different parameters can influence the effectiveness of our reactors. Our assay reveals the custom ability nature of plasma reactors for hematologic cancer therapy and our findings can be used for further development of such reactors using multi-objective optimisation techniques.

Variability of the Spreading of the Patos Lagoon Plume Using Numerical Drifters

The Patos Lagoon coastal plume is a small-scale outflow that is strongly controlled by meteorological tides. However, the riverine discharge of the lagoon is subject to high decadal variability. Hence, the discharge amount alters the scale of this coastal plume and its effects over the inner shelf environment. This study uses hydrodynamic simulations and a Lagrangian model to estimate the spreading of the plume under two different discharge conditions.Through scale parameters, we characterized the contrasts of the plume structure between high discharge and low discharge conditions. During a strong discharge regime, the width and thickness of the plume are enhanced, and the inertial processes increase against the frictional effect of the wind. The consequences of these differences include higher values of alongshore and cross-shore spreading of the drifters for the strong discharge regime. These findings indicate that under similar wind conditions, different amounts of riverine discharges alter the extent to which the material delivered by the plume can spread over the inner continental shelf.

Synoptic Flow Variability in a River-Influenced Inner Shelf off Central Chile

The response of inner shelf circulation and bottom temperature variability to synoptic wind forcing and freshwater outflow is evaluated in an area with a wide continental shelf off central Chile. This forced circulation, with a strong seasonal evolution from upwelling- to downwelling-favorable conditions, is a key process modulating the exchange of water properties in a coastal zone characterized by multiple river outflows and high biological productivity. Ocean currents on the inner shelf (34 m depth) off the Itata River mouth were obtained and analyzed for a nine-month record (December 2008 to September 2009). The synoptic wind and current variability was defined between 2 and 16 days (0.02 to 0.0026 cph). The subinertial coastal circulation within the inner shelf off Itata River was dominated by the along-shelf flow, while cross-shelf flows driven by along-shelf winds were substantially reduced. The alongshore synoptic currents showed two distinct modal structures: (i) A mean two-layer flow field during upwelling-favorable wind stress with northward (southward) flow at the surface (bottom), and (ii) a mean southward flow through the entire water column during downwelling-favorable wind stress periods, which were intensified during peak river discharge events in winter. Calculations of the wind index clarified the relative importance of wind versus buoyancy forcing on the alongshore flow. The wind forcing dominated during summer when the river discharge was minimum, whereas the relative importance of the freshwater outflow from the Itata River became dominant in winter (May-August) when the buoyancy forcing, in conjunction with southward wind events, modulated strong barotropic southward flows. The change in the long-term regime of coastal winds and river discharges, with a dominance of upwelling winds and reduced river outflows in the last decade, is discussed in the context of observations of thinner river plumes under frequent upwelling conditions off central Chile.

Self-Organized Space Charge Structure Formations in DC Glow Discharge

Experimental investigations of a hollow cathode discharge through the controlled variation of anode potential inside a hollow cylindrical cavity, in the absence and presence of the magnetic field, reveal the self-organization of uniform complex space charge structure formation around the spherical anode into concentrated localized anode spots. The discharge current&#x2013;voltage (<inline-formula> <tex-math notation="LaTeX">$I$ </tex-math></inline-formula>&#x2013;<inline-formula> <tex-math notation="LaTeX">$V$ </tex-math></inline-formula>) characteristic along with the electrostatic floating potential and discharge current fluctuations measured during the glow discharge regime suggest that the initial stable multiple sheath formation around the anode dissociates into intermittent multiple localized anode spot formations while passing through transient states during anode potential variation. On introducing a magnetic field, the localized concentrated anode spot formations on the anode surface undergo random distribution through self-organized criticality (SOC) and pronounced low-frequency oscillations (&#x007E;52.4 kHz). These oscillations gradually develop into harmonics of 100 kHz on further increasing the anode potential in the presence of the external magnetic field. Various discharge regimes are investigated through the time-resolved floating potential variation measurements using a cylindrical Langmuir probe (LP). We report on the relation between the discharge variations with the nonlinear time series analysis of the discharge current and floating potential fluctuations through the reconstructed phase space in different time domains to analyze the dynamics of complex structure formations and the existence of SOC behavior during the present hollow cathode discharge regime. The study of self-organized pattern formations and SOC behavior is vital for understanding the complex behavior of plasmas in the field of strongly coupled plasmas, plasma-based surface treatments, and thrusters for further development.