Regenerative Technologies Research Articles

Direct Regeneration of Spent LiCoO2 Black Mass Based on Fluorenone‐Mediated Lithium Supplementation and Energy‐Saving Structural Restoration

AbstractDegraded LiCoO2 cathode from retired Li‐ion batteries is urgently required to be recycled in a greener way for economic and environmental considerations. The coarse metallurgy technologies for Li/Co extraction with massive CO2 emission and energy consumption cannot satisfy the requirements of carbon neutralization. Herein, it is proposed that direct regeneration of degraded LiCoO2 cathode could be realized via 9‐fluorenone‐mediated Li supplementation and follow‐up structural restoration. The 9‐fluorenone‐lithium reagent is elaborately selected to compensate for the missing Li+ into lattice with targeted stoichiometry owing to its compatible redox potential of 1.95 V versus Li+/Li, which is located just between the reversible intercalation (3.8 V) and irreversible conversion (1.2 V) potentials of LiCoO2 electrode. Then, thermal energy‐driven structure reorganization enables Li/Co atoms to occupy the right sites, accomplishing desirable structure healing within a short annealing time of 4 h. The regenerated LiCoO2 cathode exhibits comparable Li‐storage capability to commercial LiCoO2, benefiting from the non‐destructive direct regeneration technology. In addition, the regeneration route is regarded as environmentally (0.13 kg CO2 kg−1 cell) and economically (10.07 $ kg−1 cell) superior to conventional recycling routes based on life‐cycle analysis. The precise surgery on spent LiCoO2 cathode provides a promising solution for the forthcoming retirement rush of Li‐ion batteries.

Theoretical aspects regarding the use of autologous and allogeneic septal cartilage transplantation in rhinologic surgical procedures

The study examines the use of autologous and allogeneic septal cartilage transplantation in rhinoplasty and rhi­no­sep­to­plasty. Innovative surgical techniques such as endoscopic and open septal cartilage harvesting were examined, high­ligh­ting advantages such as faster postoperative re­co­very and better visualization of nasal anatomy, as well as dis­ad­van­tages such as a steep learning curve and com­pli­ca­tions as­so­cia­ted with endoscopic manipulation. The postoperative out­­comes of patients undergoing rhinoplasty with auto­lo­gous car­ti­lage implants showed increased satisfaction re­gar­ding na­sal esthetic appearance and functionality. Re­gar­ding al­lo­ge­neic cartilage transplantation, risks of re­jec­tion and in­fec­tion were highlighted. Future perspectives in sep­tal car­ti­lage transplantation included improving surgical tech­­niques and optimizing outcomes, as well as exploring the use of innovative materials and technologies for cartilage tissue regeneration and remodeling. Aspects related to the in­te­gra­tion and revitalization of transplanted cartilage were studied in detail, including processes of angiogenesis, cel­lular colonization, and extracellular matrix biosynthesis. Sur­geons’ preferences regarding the use of autologous or al­lo­ge­neic cartilage were examined, highlighting the reasons and criteria underlying their choices. In conclusion, cartilage trans­plants are effective and safe in rhinologic surgical inter­ven­tions, although the study has limitations related to source avai­la­bi­lity and methodological variability.

Ultrasound-guided accesses for regenerative injection therapy of hip and knee

Interventional diagnostic and therapeutic technologies have gained considerable popularity in many surgical specialties – cardiology, vascular surgery, neurosurgery, oncology, and in orthopedics and traumatology. But unlike other specialties, ultrasound became the driving force behind the development and implementation of interventional technologies in the treatment of diseases of the musculoskeletal system. In recent years, ultrasound-guided injections have gained significant popularity, as they have given an advantage in accuracy compared to injections without such navigation. The purpose of our study was the development of ultrasound navigation accesses to the hip and knee joints for the interventional application of regenerative technologies in their pathology. The material for the study was the results of ultrasound examination of the hip and knee joints of 486 patients with diseases and injuries of the hip and knee, who were treated in the scientific and practical department of tissue and cell therapy of the State Institute of Traumatology and Orthopedics of the National Academy of Medical Sciences of Ukraine in the period from 2016 to 2023. The results. The following accesses to the knee joint under ultrasound navigation have been developed: suprapatellar longitudinal access for injections into the quadriceps tendon and patellofemoral joint, suprapatellar longitudinal access with knee bending for injections into the upper turn of the knee joint, infrapatellar longitudinal access for injections into the patellar ligament and deep infrapatellar bursa, infrapatellar transverse access for injections into Hoffa’s fat pad, lateral longitudinal access with knee bending for injections into the lateral meniscus, medial longitudinal access with bending in the knee for injections in the medial meniscus, medial transverse access for injections in the medial part of the joint space, lateral transverse access with bending in the knee joint for injections in the lateral part of the joint space, lateral longitudinal access for performing injections in the collateral fibular ligament, medial longitudinal access for performing injections in the collateral tibial ligament, infrapatellar diagonal access for performing injections in the “crow’s foot” area of the knee joint, infrapatellar medial longitudinal access for performing other injection into the medial meniscus and joint capsule, lateral longitudinal access for injections into the tendons of the biceps femoris and hamstrings. The following accesses have been developed for the hip joint: anterior longitudinal access for performing injections in the subcapsular-cervical space, anterior diagonal access for performing injections in the acetabular labrum, capsule-ligament apparatus of the hip and tendon of the rectus femoris muscle, lateral longitudinal access for performing injections in the paratrochanteric region. Conclusions. 13 ultrasonic navigation accesses have been developed for the administration of biotechnological products into the knee joint and 3 – into the hip join, which allow not only to detect damaged intra-articular and para-articular structures of the knee and hip joints, but also to deliver an orthobiologics products directly to them for maximum regenerative effect.

Effective microwave regeneration of natural sepiolite and montmorillonite as adsorbents for tetracycline removal and mechanism insight

Natural clay minerals such as sepiolite (Sep) and montmorillonite (Mt) are used as low-cost adsorbents to remove tetracycline (TC) in water, and the spent adsorbents saturated with TC are regenerated under microwave (MW) irradiation. The adsorption and regeneration properties of Sep and Mt are compared. The possible adsorption and MW regeneration mechanisms are proposed. The results show that 11.25 mg·g−1 and 20.74 mg·g−1 adsorption capacities of Sep and Mt are obtained, respectively, within 120.0 min at 298 K. Mt has higher adsorption capacity, faster adsorption rate and shorter adsorption time for TC than that of Sep. The adsorption processes using Sep and Mt are well-fitted to pseudo-second-order kinetics and Langmuir models. The two adsorption reactions are spontaneous and endothermic, with increased randomness at solid–liquid interfaces. Moreover, 89.76 % and 114.45 % maximum regeneration ratios are obtained for Sep and Mt, respectively. Mt exhibits superior regeneration performance than Sep. After eight adsorption-regeneration cycles, the two adsorbents can maintain excellent adsorption and regeneration performance. This work provides new perspectives on the adsorption technology using natural clay minerals to remove antibiotics and the MW regeneration technology to regenerate spent natural clay minerals saturated with organic pollutants in organic wastewater treatment.

Experimental investigation of PCL‐based composite material fabricated using solvent‐cast 3D printing process

AbstractBone tissue engineering relies on scaffolds with enhanced mechanical properties, achievable through 3D printing techniques. Our study focuses on enhancing mechanical properties using a solvent‐cast 3D printing method. For this, poly‐ε‐caprolactone (PCL) reinforced with polyhydroxybutyrate (PHB), and synthetic fluorapatite (FHAp) nanopowders were utilized, immersed in a solution of dichloromethane (DCM) and dimethylformamide (DMF). Sol–gel method was used to synthesized FHAp, and the XRD pattern confirmed crystalline FHAp presence, with notable peaks at 2θ values of 31.937°, 33.128°, 32.268°, and 25.864°. Moreover, composites exhibited nonchemical PCL‐PHB/FHAp interactions, with PHB and FHAp crystallographic planes evident. Surface roughness, assessed via RMS values, showed progressive increases with higher PHB and FHAp content. Tensile strength peaked at 19% wt/v of PHB, with varied effects of FHAp. Compressive strength reached its apex at 30% wt/v of FHAp, with higher PHB content consistently enhancing strength. Flexural strength notably increased with PHB, peaking at 19% wt/v, and further with FHAp. Young's modulus rose with both PHB and FHAp content. Hardness increased with PHB and FHAp, notably peaking at 30% wt/v of FHAp. Cell viability improved with PHB, showing varied responses to FHAp. Hemocompatibility evaluations indicated low hemolysis percentages, especially in balanced PHB/FHAp compositions. These findings highlight the crucial role of composite compositions in tailoring mechanical and biological properties for optimal bone scaffold design, promising advancements in tissue regeneration technologies.

Preliminary application of antibiotic bone cement directly inducing skin regeneration technology in repairing of wound in lateral toe flap donor area

To investigate the feasibility and effectiveness of antibiotic bone cement directly inducing skin regeneration technology in the repairing of wound in the lateral toe flap donor area. Between June 2020 and February 2023, antibiotic bone cement directly inducing skin regeneration technology was used to repair lateral toe flap donor area in 10 patients with a total of 11 wounds, including 7 males and 3 females. The patients' age ranged from 21 to 63 years, with an average of 40.6 years. There were 3 cases of the distal segment of the thumb, 2 cases of the distal segment of the index finger, 1 case of the middle segment of the index and middle fingers, 1 case of the distal segment of the middle finger, and 3 cases of the distal segment of the ring finger. The size of the skin defect of the hand ranged from 2.4 cm×1.8 cm to 4.3 cm×3.4 cm. The disease duration ranged from 1 to 15 days, with an average of 6.9 days. The flap donor sites were located at fibular side of the great toe in 5 sites, tibial side of the second toe in 5 sites, and tibial side of the third toe in 1 site. The skin flap donor site wounds could not be directly sutured, with 2 cases having exposed tendons, all of which were covered with antibiotic bone cement. All patients were followed up 6 months to 2 years, with an average of 14.7 months. All the 11 flaps survived and had good appearance. The wound healing time was 40-72 days, with an average of 51.7 days. There was no hypertrophic scar in the donor site, which was similar to the color of the surrounding normal skin; the appearance of the foot was good, and wearing shoes and walking of the donor foot were not affected. It is a feasible method to repair the wound in the lateral foot flap donor area with the antibiotic bone cement directly inducing skin regeneration technology. The wound heals spontaneously, the operation is simple, and there is no second donor site injury.

Advances in soft tissue wound care: A Comprehensive Review of Facial traumatic injuries

Soft tissue wound care, particularly in the context of facial traumatic injuries, has undergone significant progress propelled by interdisciplinary collaborations between medical professionals and engineers. This comprehensive review explores the evolution of traditional and advanced techniques for managing soft tissue wounds, emphasizing innovations in scar prevention and the integration of cutting-edge technologies. This review covers the immediate assessment and management of facial traumatic injuries, traditional wound care approaches, and the latest advancements in soft tissue wound healing. Notably, collaborative efforts in biomechanical engineering have led to the development of bioengineered scaffolds, innovative dressings, and customizable implants that promise to revolutionize wound closure and tissue regeneration. The integration of robotics into soft tissue wound care procedures has shown promise in improving precision, reducing invasiveness, and enhancing surgical interventions. Additionally, regenerative technologies, including tissue engineering, 3D bioprinting, and regenerative medicine approaches, offer novel strategies for harnessing the body's natural healing processes. Looking ahead, the future of soft tissue wound care holds exciting prospects, including advancements in technology and imaging for more precise diagnostics, personalized medicine approaches tailored to individual patient profiles, and continued collaboration between medicine and engineering to develop innovative solutions. These future directions are poised to redefine the landscape of soft tissue wound care, offering improved outcomes and quality of life for individuals with facial traumatic injuries and other complex wounds.

Digital planning and bone regenerative technologies: A narrative review.

The aim of this narrative review was to explore the application of digital technologies (DT) for the simplification and improvement of bone augmentation procedures in advanced implant dentistry. A search on electronic databases was performed to identify systematic reviews, meta-analyses, randomized and non-randomized controlled trials, prospective/retrospective case series, and case reports related to the application of DT in advanced implant dentistry. Seventy-nine articles were included. Potential fields of application of DT are the following: 1) the use of intra-oral scanners for the definition of soft tissue profile and the residual dentition; 2) the use of dental lab CAD (computer-aided design) software to create a digital wax-up replicating the ideal ridge and tooth morphology; 3) the matching of STL (Standard Triangulation Language) files with DICOM (DIgital COmmunication in Medicine) files from CBCTs with a dedicated software; 4) the production of stereolithographic 3D models reproducing the jaws and the bone defects; 5) the creation of surgical templates to guide implant placement and augmentation procedures; 6) the production of customized meshes for bone regeneration; and 7) the use of static or dynamic computer-aided implant placement. Results from this narrative review seem to demonstrate that the use of a partially or fully digital workflow can be successfully used also in advanced implant dentistry. However, the number of studies (in particular RCTs) focused on the use of a fully digital workflow in advanced implant dentistry is still limited and more studies are needed to properly evaluate the potentials of DT.

Degradation Mechanisms of Electrodes Promotes Direct Regeneration of Spent Li-Ion Batteries: A Review.

The rapid growth of electric vehicle use is expected to cause a significant environmental problem in the next few years due to the large number of spent lithium-ion batteries (LIBs). Recycling spent LIBs will not only alleviate the environmental problems but also address the challenge of limited natural resources shortages. While several hydro- and pyrometallurgical processes are developed for recycling different components of spent batteries, direct regeneration presents clear environmental, and economic advantages. The principle of the direct regeneration approach is restoring the electrochemical performance by healing the defective structure of the spent materials. Thus, the development of direct regeneration technology largely depends on the formation mechanism of defects in spent LIBs. This review systematically details the degradation mechanisms and types of defects found in diverse cathode materials, graphite anodes, and current collectors during the battery's lifecycle. Building on this understanding, principles and methodologies for directly rejuvenating materials within spent LIBs are outlined. Also the main challenges and solutions for the large-scale direct regeneration of spent LIBs are proposed. Furthermore, this review aims to pave the way for the direct regeneration of materials in discarded lithium-ion batteries by offering a theoretical foundation and practical guidance.

Electrolytic Regeneration of Spent Caustic Soda from CO2 Capture Systems

The traditional electrochemical caustic soda recovery system uses the generated pH gradient across the ion exchange membrane for the regeneration of spent alkaline absorbent from CO2 capture. This electrochemical CO2 capture system releases the by-products H2 and O2 at the cathode and anode, respectively. Although effective for capturing CO2, the slow kinetics of the oxygen evolution reaction (OER) limit the energy efficiency of this technique. Hence, this study proposed and validated a hybrid electrochemical cell based on the H2-cycling from the cathode to the anode to eliminate the reliance on anodic oxygen generation. The results show that our lab-scale prototype enabled effective spent caustic soda recovery with an electron utilisation efficiency of 90%, and a relative carbonate/bicarbonate diffusional flux of approximately 40%. The system also enabled the regeneration of spent alkaline absorbent with a minimum electrochemical energy input of 0.19 kWh/kg CO2 at a CO2 recovery rate of 0.7 mol/m2/h, accounting for 30% lower energy demand than a control system without H2-recycling, making this technique a promising alternative to the conventional thermal regeneration technology.

Lysophosphatidic Acid/Polydopamine-Modified nHA Composite Scaffolds for Enhanced Osteogenesis via Upregulating the Wnt/Beta-Catenin Pathway.

Guided bone regeneration (GBR) technology has been widely used for the regeneration of periodontal bone defects. However, the limited mechanical properties and bone regeneration potential of the currently available GBR membranes often limit their repair effectiveness. In this paper, serum-derived growth factor lysophosphatidic acid (LPA) nanoparticles and dopamine-decorative nanohydroxyapatite (pDA/nHA) particles were double-loaded into polylactic-glycolic acid/polycaprolactone (PLGA/PCL) scaffolds as an organic/inorganic biphase delivery system, namely, PP-pDA/nHA-LPA scaffolds. Physicochemical properties and osteogenic ability in vitro and in vivo were performed. Scanning electron microscopy and mechanical tests showed that the PP-pDA/nHA-LPA scaffolds had a 3D bionic scaffold structure with improved mechanical properties. In vitro cell experiments demonstrated that the PP-pDA/nHA-LPA scaffolds could significantly enhance the attachment, proliferation, osteogenic differentiation, and mineralization of MC3T3-E1 cells. In vivo, the PP-pDA/nHA-LPA scaffolds exhibited great cytocompatibility and cell recruitment ability in 2- and 4-week subcutaneous implantation experiments and significantly promoted bone regeneration in the periodontal defect scaffold implantation experiment. Moreover, LPA-loaded scaffolds were confirmed to enhance osteogenic activities by upregulating the expression of β-catenin and further activating the Wnt/β-catenin pathway. These results demonstrate that the biphase PP-pDA/nHA-LPA delivery system is a promising material for the GBR.

The 3-dimensional printing for dental tissue regeneration: the state of the art and future challenges.

Tooth loss or damage poses great threaten to oral and general health. While contemporary clinical treatments have enabled tooth restoration to a certain extent, achieving functional tooth regeneration remains a challenging task due to the intricate and hierarchically organized architecture of teeth. The past few decades have seen a rapid development of three-dimensional (3D) printing technology, which has provided new breakthroughs in the field of tissue engineering and regenerative dentistry. This review outlined the bioactive materials and stem/progenitor cells used in dental regeneration, summarized recent advancements in the application of 3D printing technology for tooth and tooth-supporting tissue regeneration, including dental pulp, dentin, periodontal ligament, alveolar bone and so on. It also discussed current obstacles and potential future directions, aiming to inspire innovative ideas and encourage further development in regenerative medicine.

From Basic Science to Clinical Practice: A Review of Current Periodontal/Mucogingival Regenerative Biomaterials.

Periodontitis is a dysbiosis-driven inflammatory disease affecting the tooth-supporting tissues, characterized by their progressive resorption, which can ultimately lead to tooth loss. A step-wise therapeutic approach is employed for periodontitis. After an initial behavioral and non-surgical phase, intra-bony or furcation defects may be amenable to regenerative procedures. This review discusses the regenerative technologies employed for periodontal regeneration, highlighting the current limitations and future research areas. The search, performed on the MEDLINE database, has identified the available biomaterials, including biologicals (autologous platelet concentrates, hydrogels), bone grafts (pure or putty), and membranes. Biologicals and bone grafts have been critically analyzed in terms of composition, mechanism of action, and clinical applications. Although a certain degree of periodontal regeneration is predictable in intra-bony and class II furcation defects, complete defect closure is hardly achieved. Moreover, treating class III furcation defects remains challenging. The key properties required for functional regeneration are discussed, and none of the commercially available biomaterials possess all the ideal characteristics. Therefore, research is needed to promote the advancement of more effective and targeted regenerative therapies for periodontitis. Lastly, improving the design and reporting of clinical studies is suggested by strictly adhering to the Consolidated Standards of Reporting Trials (CONSORT) 2010 statement.

Рекуперация и очистка газовых выбросов целлюлозного производства

For pulp production, large-scale enterprises have been built which, while in operation, are subject to new requirements, different from the design ones, for economic efficiency, labour safety, as well as impact on the local population and the environment. Significant success in this work has been achieved by changing the liquor recovery technology, switching to burning black liquor of increased concentration, which makes it possible to almost completely eliminate the largest source of hydrogen sulfide and methyl mercaptan emissions with flue gases, reduce sulfur losses and improve energy efficiency of soda recovery boilers. Another significant source of soda recovery boiler emissions is a smelt dissolving tank vent. An important technological operation of dissolving molten sodium salts with weak white liquor supplied from the causticization shop takes place in the tank. The modern development of smelt leaching technology is related to the improvement of equipment compatible with the technology of regeneration of chemical reagents for pulp production. Heat exchangers and gas purifiers of “gas-liquid” systems, easier to adapt to technological requirements compared to other systems, are installed on the dissolving tank vent. The installation of such equipment provides the change in the smelt leaching technology, and affects the technology of causticization and lime recovery. This article covers the research of the relationship between the technical solutions ensuring the safety of personnel in the boiler shop, heat and chemicals recovery, as well as purification of gas emissions and the changes in the technology of smelt leaching in the soda recovery boiler of the pulp mill. On the basis of experimental data and a mathematical model of the movement of the vapour-gas mixture in the smelt dissolving tank vent, the technological feasibility of installing heat exchangers at different heights of the vent and the possibility of effective purification of gas emissions using a direct-flow sprayer have been considered. The applicability of the irrigation of the steam-gas flow with weak white liquor, which is formed during the cycle of chemical regeneration in pulp production, as well as the conditions for ensuring reliable operation of gas purification equipment, have been investigated. The quantitative characteristics of the necessary change in consumption and composition of weak white liquor and the methods of its supply to the dissolving tank have been obtained.

Electrochemical Regeneration of Highly Stable and Sustainable Cellulose/Graphene Adsorbent Saturated with Dissolved Organic Dye.

Electrochemical regeneration of adsorbents presents a cost-effective and environmentally friendly approach. Yet, its application to 3D structured adsorbents such as cellulose/graphene-based aerogels remains largely unexplored. This study introduces a method for producing these aerogels, highlighting their significant adsorption capacity for dissolved organic pollutants and resilience during electrochemical regeneration. By adjusting the ratio of hydrophobized cellulose nanofibers to graphene, the aerogels demonstrate a tunable adsorption capacity, ranging from 56 to 228 mg/g. Hydrophobization using oleic acid is vital for maintaining the aerogels' structural stability in water. Notably, the aerogels maintain structural integrity and efficiency over at least 18 electrochemical regeneration cycles, underscoring their potential for long-term environmental applications. The increase in adsorption capacity observed after regeneration cycles, approximately 10-20% by the fifth cycle, is attributed to electrochemical surface roughening and the creation of new adsorption sites. The tunability and durability of these aerogels offer a sustainable solution for adsorption with electrochemical regeneration technology.

Application of intentional replantation in advanced periodontitis involving teeth preservation.

With the development of periodontal regenerative technology, an increasing number of scholars reported that advanced periodontitis involving teeth can be preserved through intentional replantation. Intentional replantation has become the last possible method to preserve natural teeth for advance periodontitis with signs of tooth extraction. However, the indications of intentional replantation are strict, and the success of the operation is closely related to the condition of cases and the operation skills of doctors. In this article, the operation steps and criteria of intentional replantation were summarized by introducing three success cases of advanced periodontitis involving teeth preserved by intentional replantation. The relevant factors that affect the prognosis of intentional replantation in advanced periodontitis involving teeth preservation were analyzed to help clinicians preserve natural teeth.

Orthodontic tooth movement after periodontal regeneration of intrabony defects.

The prevalence of intrabony defects in patients with advanced periodontitis stages III and IV is high. These patients usually need both periodontal treatment and orthodontic therapy, including tooth movement through bone defects, to improve masticatory function, aesthetics, and overall quality of life. Clinical practice guidelines recommend periodontal regenerative surgical interventions to resolve these defects and propose initiating orthodontic tooth movement (OTM) once periodontal therapy goals have been met. Surgical interventions using various regenerative technologies like barrier membranes and enamel matrix proteins, combined or not with bone replacement grafts, have proven effective in regenerating lost periodontal tissues. However, the combination of periodontal and orthodontic treatments requires consideration of how periodontal regenerative therapies influence OTM. Studies suggest that regenerated bone may differ in density, composition, vascularity, and cellular activity, potentially affecting the speed and efficiency of OTM, and potential root resorption of moved teeth. Understanding the sequence and timing of implementing OTM after regenerative periodontal interventions is crucial due to their interlinked processes of bone resorption and formation. This narrative review aims to uncover scientific evidence regarding these combined treatments, examining the impacts of different regenerative technologies on OTM and delineating their advantages, limitations, and best practices.

Rapid in situ regeneration of phenol-saturated activated carbon fiber by an electro-permonosulfate-ozone process: Performance, operators and mechanism

In this study, a new method that encompasses electricity, permonosulfate (PMS), and ozone (E-PMS-O3) was proposed and applied in the regeneration of phenol-saturated activated carbon fiber (ACF). Compared with traditional regeneration technology, the E-PMS-O3 process simultaneously regenerated exhausted ACF in situ and mineralized the desorbed pollutants effectively (78.67%) with relatively low energy consumption (4.338 kWh m−3). Furthermore, the E-PMS-O3 regeneration process only required 2 h, which was shorter than other well-documented electro-advanced oxidation processes (EAOPs), such as the E-O3 process lasting for 3 h, the E-persulfate process for 6 h, and the E-Fenton process for 6 h. Possible pathways in the regeneration process include direct electron transfer, ozone oxidation, PMS oxidation, non-radical reactions, and reactive oxygen species (ROS) oxidations. Two main ROS — hydroxyl radical (O•H) and sulfate radical (SO4•−) were probed and their contribution ratio was approximately 1:1. An external electric field visibly enhanced the recovery adsorption capacity of ACF and accelerated the decomposition of PMS. Interestingly, additional experiments revealed that adding two different oxidants (PMS/O3) provided a better protection effect on the properties of ACF against oxidation of oxidants and ROS. It's important to mention that the maximum concentration of byproducts remained below 5 mg g−1, which effectively minimized the potential for subsequent pollution. In the end, multiple regeneration cycles demonstrated that the regeneration efficiency was nearly 60% even after 6 cycles. Hence, the E-PMS-O3 process was promising for further exploration and discussion when applied in regeneration of exhausted AC materials.

Laboratory investigation on the properties of warm mixing-recycled asphalt containing waste oil and plastics

ABSTRACT The integration of warm-mix and regeneration technologies is gaining momentum due to its dual advantages: enhancing the utilization of recycled asphalt and promoting environmental sustainability. In this study, these technologies by leveraging waste materials were synergized. Specifically, kitchen waste oil underwent chemical treatment to serve as a rejuvenator, while waste low-density polyethylene was transformed into pyrolysis wax, a beneficial additive for the asphalt mix. Utilizing these waste components, a sustainable warm mixing-recycled asphalt blend was formulated. This blend’s efficacy was meticulously evaluated through viscosity tests, rheological assessments, four-component analyses, and FT-IR evaluations. Optimal results emerged when incorporating 5% waste pyrolysis wax and 3.3% waste oil into warm recycled asphalt, notably improving viscosity reduction, high-temperature performance, rutting resistance, and fatigue life at 25 °C. Moreover, the four-component test shows the component of aged asphalt after adding the optimal combination is basically consistent with that of the neat asphalt. Importantly, FT-IR tests affirmed that pyrolysis wax bolstered the blend’s oxidation resistance. Through gray correlation analysis, we deduced that asphalt’s component changes are intricately linked with rheological property variations. Notably, the carbonyl index exhibited a pronounced negative correlation with rutting and fatigue life.

Comparative Analysis of Hyaline Cartilage Characteristics and Chondrocyte Potential for Articular Cartilage Repair.

This study aimed to compare the histological, biochemical, and mechanical characteristics of hyaline cartilage in different regions and evaluate the potential of chondrocytes extracted from each region as donor sources for articular cartilage repair. The cartilage tissues of the femoral head and knee joint, ribs, nasal septum, thyroid, and xiphoid process of adult Bama pigs were isolated for histological, biochemical, and mechanical evaluation and analysis. The corresponding chondrocytes were isolated and evaluated for proliferation and redifferentiation capacity, using biochemical and histological analysis and RT-PCR experiments. Compared with articular cartilage, non-articular hyaline cartilage matrix stained more intensely in Safranin-O staining. Glycosaminoglycan and total collagen content were similar among all groups, while the highest content was measured in nasal septal cartilage. Regarding biomechanics, non-articular cartilage is similar to articular cartilage, but the elastic modulus and hardness are significantly higher in the middle region of costal cartilage. The chondrocytes extracted from different regions had no significant difference in morphology. Hyaline cartilage-like pellets were formed in each group after redifferentiation. The RT-PCR results revealed similar expressions of cartilage-related genes across the groups, albeit with lower expression of Col2 in the xiphoid chondrocytes. Conversely, higher expression of Col10 was observed in the chondrocytes from the rib, thyroid, and xiphoid cartilage. This study provides valuable preclinical data for evaluating heterotopic hyaline cartilage and chondrocytes for articular cartilage regeneration. The findings contribute to the selection of chondrocyte origins and advance the clinical translation of technology for cartilage regeneration.