Infiltration Rate Research Articles

Tillage practices on soil penetration resistance, soil infiltration, percolation and yield of rice (Oryza sativa) in rice-based cropping system

The experiment was conducted during 2019–23 at Tamil Nadu Rice Research Institute (Tamil Nadu Agricultural University, Coimbatore), Aduthurai, Tamil Nadu to analyse the effect of conservation tillage methods on bulk density, soil penetration resistance and soil infiltration rate of clay soil and rice yield in rice-based cropping system. Experiment consisted of three tillage practices, viz. conventional tillage/puddling (CT); zero tillage (ZT); and minimal tillage/dry ploughing (MT) and two rice (Oryza sativa L.) cultivars (ADT 43 and CORH 3), replicated four times. The result of the study revealed that the bulk density was significantly lower with zero tillage due to presence of crop residues and addition of organic matter. The mean infiltration rate under zero tillage was 0.16 cm/h as compared to puddling (0.14 cm/h) and dry ploughing (0.20 cm/h). The study further showed that the mean soil percolation rate was significantly altered by the tillage methods and soil percolation rate was 0.12 cm/h in zero tillage as compared to puddling (0.10 cm/h) and dry ploughing (0.16 cm/h). In contrary to the other physical properties, the soil penetration resistance was in the order of dry ploughing>zero tillage>puddling. The mean soil penetration resistance under zero tillage was reduced from 690–500 Kpa, 740–600 Kpa and 760–620 Kpa respectively at 0–5, 5–10 and 10–15 cm depth as compared to puddling. The results further indicated that the yield parameters and rice did not differ among the different tillage practices.

Deep-root respiration: The unknown CO2 removed from the atmosphere

Carbon (C) sequestration in soils is a promising CO2 removal approach. So far, the focus has been on how to increase the content of soil organic C (SOC), while the management soil inorganic C (SIC), i.e. carbonate minerals, has received little attention, because SIC is thought to be much less involved in biotic C cycling than SOC. However, in principle SIC management potentially provides a long-term solution, with a much greater capacity for C sequestration than SOC. The forgotten link is the dissolved inorganic carbon (DIC), i.e. CO2 species dissolved in soil solution, and its fate throughout the unsaturated zone (USZ). The return of CO2 respired by deep roots to the atmosphere, either directly through CO2 degassing or indirectly through DIC leaching, may not necessarily take place over decades or centuries. CO2 diffusion decreases sharply with depth due to reduced porosity of the subsoil and more water-filled pores. The downward water percolation rate is often only a few centimeters per year, and the large amount of respired CO2 compared to the leached DIC results in a relatively small amount of CO2 being transferred to the groundwater. Therefore, respired CO2 at deeper soil depth can be defined as a hitherto unknown ecosystem service of deep-rooted plants i.e. providing a net C sink as inorganic C in the USZ. A conservative estimation suggests a C sink as SIC of at least 80 kg C ha−1 y−1, comparable to reported annual C sequestration as SOC in temperate grasslands.

The Addition of Pore Holes in Paving Blocks in an Effort to Increase Infiltration

The problem of waterlogging and surface runoff on impermeable pavement surfaces requires finding new ways to manage water flow, especially from rainwater. The type of permeable pavement that is often used is paving block. The use of paving blocks for pavement materials is expected to reduce puddles that occur after rain. One way is to modify the paving block to be greater in seeping water into the soil. This study aims to determine the extent to which the effect of adding pore holes in paving block can increase water infiltration in surrounding soil. This research was conducted through testing in the Laboratory. The type of research is quantitative with experimental method using a rain simulator tool with variations of paving block. From the research results obtained that the addition of pores in the paving block affects the infiltration that occurs. This is evidenced by the increae in the value of infiltration, the infiltration rate value of normal paving block is 182.92-10.43 mm/hour, 2% ratio is 183.75-10.75 mm/hour, 5% ratio is 190.00-11.30 mm/hour, 7% ratio is 231.33-11.46 mm/hour, 10% ratio is 236.88-17.61 mm/hour. From the test results between pore holes with infiltration rate has a significant relationship of 0.037 (<0,05).

Deep Hydrogen Reservoirs and Longevity

The oceans are voluminous H2O reservoirs that regulate climate and life on Earth. Yet much larger H2O reservoirs, potentially accounting for several oceans, may exist in the Earth’s mantle and core in the form of H atoms trapped into the structure of nominally anhydrous minerals (NAMs) and metallic alloys. Determining the size of these ‘hidden oceans’ is key to understanding planetary evolution and surface dynamics and can be done by combining data from rare natural samples with experimental and theoretical models. The longevity of these deep H reservoirs is controlled by H transport rates over geological times, which are dominated by percolation rates, once H partitions into melts, or by plate mobility, if H remains locked in NAMs.

Minimizing Invasiveness in Neurosurgical Osteotomies: A Comparative Histomorphometric Study of Piezoelectric Craniotomy versus High-Speed Drill

Piezoelectric bone cutting has gained popularity in neurosurgical osteotomies due to perceived lower trauma compared to rotary instruments. However, histological confirmation of its decreased aggressiveness is lacking, hindering conclusive proof. This study compares the bony and neuro-meningeal invasiveness of piezoelectric craniotomy with high-speed drill techniques. Histological data from 21 sheep undergoing piezoelectric craniotomy and 19 sheep subjected to high-speed electric drill craniotomy were compared. Piezoelectric craniotomy utilized a 0.35 mm micro saw titanium nitride coated. Outcome parameters included the detection of the "smear layer," average osteoblast count per high-power field, and residual bone matrix for bony invasiveness assessment. Parameters for meningeal and brain parenchymal invasiveness included pachymeningeal and leptomeningeal injury, gliosis, and histiocytic infiltration. Statistical significance was determined at P < 0.05. Results showed the Piezo group had fewer frequent smear layers (P <0.001), higher residual bone matrix (P < 0.05), and greater osteoblast counts per high-power field (P < 0.05). Additionally, the Piezo group exhibited lower rates of leptomeningeal injury, cerebral gliosis, and histiocytic infiltration (P < 0.05). Piezoelectric craniotomy preserves residual osteoblast viability and leptomeningeal integrity while demonstrating lower rates of thermally induced gliosis and histiocytic infiltration compared to high-speed drills. This suggests the piezoelectric osteotome's minimal invasiveness in bone, meningeal, and brain tissue.

Prediction of proximal junctional kyphosis and failure after corrective surgery for adult spinal deformity: an MRI-based model combining bone and paraspinal muscle quality metrics

BACKGROUNDProximal junctional kyphosis (PJK) and proximal junctional failure (PJF) are common complications observed after adult spinal deformity (ASD) surgery and major cause for unplanned reoperations. In addition to spinal alignment, osteoporosis and paraspinal muscle (PSM) degeneration are reportedly indispensable factors that account for PJK/PJF. PURPOSETo investigate the utility of the preoperative risk assessment model using MRI-based skeletomuscular metrics in predicting PJK and/or PJF(PJK/PJF) after ASD correction. STUDY DESIGNRetrospective case-control study. PATIENT SAMPLEConsecutive series of 149 patients at a single academic institution. OUTCOME MEASURESMRI-based measurements of vertebral bone quality at upper instrumented vertebra (VBQ-U) score and fat infiltration rate (FI%) of paraspinal muscle (PSM). METHODSWe performed a retrospective analysis of patients with ASD who underwent ≥5-segment fusion. The vertebral bone quality (VBQ) scoring system was used to assess the bone quality. The PSM quality including FI% and cross-sectional area (CSA) was evaluated. Multivariate logistic regression was performed to determine potential risk factors of PJK/PJF. RESULTSOf 149 patients who underwent ASD surgery, PJK/PJF was found in 45(30.2%). Mean VBQ-U scores were 3.45±0.64 and 3.00±0.56 for patients with and without PJK/PJF (p<.001). Mean FI% of PSM(L3/L4) was 27.9±12.8 and 20.7±13.3 for patients with and without PJK/PJF (p<.001). On multivariate analysis, the VBQ-U score and FI% of PSM were significant independent predictors of PJK/PJF. The AUC for the novel risk assessment model is 0.806, with a predictive accuracy of 86.7%. CONCLUSIONIn patients undergoing ASD correction, paraspinal muscle and vertebral bone quality significantly outweigh radiographic alignment parameters in predicting PJK/PJF. The MRI-based risk assessment model offers a valuable tool for early assessing individualized risk for PJK/PJF.

Use of rice straw nano-biochar to slow down water infiltration and reduce nitrogen leaching in a clayey soil

Biochar exhibits numerous advantages in enhancing the soil environment despite a few limitations due to its lower surface energy. Nanomodified biochar combines the advantages of biochar and nanoscale materials. However, its effects on water infiltration and N leaching in a clayey soil remain unclear. Therefore, this study prepared rice straw nano-biochar by a ball milling method, and investigated its physicochemical properties and effects of bulk biochar and nano-biochar at various addition rates (0 %, 0.5 %, 1 %, 2 %, 3 %, and 5 %) on wetting peak migration, cumulative infiltration, water absorption and retention, and N leaching. The results showed that, compared with bulk biochar, nano-biochar presented a more abundant pore structure with an increase in specific surface area of approximately 1.5 times, accompanied by a 20 % increase in acid functional groups. Compared with those for clayey soil without biochar addition, the wetting front migration time was increased by 10.2 %–123.9 % and 17.0 %–257.9 %, and the cumulative infiltration volume at 60 min was decreased by 26.0 %–48.4 % and 14.1 %–62.4 % for bulk biochar and nano-biochar, respectively. The parameter S of Philip model and the parameter a of Kostiakov model for nano-biochar were lower than those for bulk biochar, whereas the parameter b of Kostiakov model was greater, indicating that nano-biochar decreased initial soil infiltration rate and increased attenuation degree of the infiltration rate. Nano-biochar increased water absorption by 8.03 % and subsequently enhanced water retention capacity relative to bulk biochar. In addition, bulk biochar and nano-biochar reduced NH4+-N leaching by 3.0 %–13.1 % and 5.7 %–39.2 %, respectively, and NO3−-N leaching by 2.7 %–3.6 % and 9.0 %–43.3 %, respectively, by decreasing N concentration and leachate volume relative to those with no biochar addition. This study provides new knowledge for nano-biochar application in a clayey soil.

Initial treatment for surgery-naïve desmoid tumors by high intensity focused ultrasound.

Desmoid tumor (DT) is a rare proliferative disease occurring in connective tissues, characterized by high infiltration and recurrence rates. While surgery remains the primary treatment, its recurrence risk is high, and some extra-abdominal desmoid tumors are inoperable due to their locations. Despite attempts with radiotherapy and systemic therapy, the efficacy remains limited. We used low-power cumulative high-intensity focused ultrasound (HIFU) therapy as an initial treatment for desmoid tumor patients either ineligible or unwilling for surgery. Low-power cumulative HIFU employs slower heat accumulation and diffusion, minimizing damage to surrounding tissues while enhancing efficacy. Fifty-seven non-FAP desmoid tumor patients, previously untreated surgically, underwent low-power cumulative HIFU therapy. Among them, 35 had abdominal wall DT, 20 had extra-abdominal DT, and 2 had intra- abdominal DT, with an 85% median ablation ratio. Abdominal wall DT patients showed significantly better response rates (91.4% vs. 86%) and disease control rates (100% vs. 32%) than that of non-abdominal wall DT patients. Median event- free survival time was not reached after a median follow-up duration of 34 months. With its high response rate, durable efficacy, and mild adverse effects, our findings suggest that low-power cumulative HIFU presents a promising novel treatment for desmoid tumors, particularly abdominal wall DT patients.

Evaluation and comparison of infiltration models for estimating infiltration capacity of different textures of irrigated soils

Accurate estimation of infiltration rates is crucial for effective irrigation system design and evaluation by optimizing irrigation scheduling, preventing soil erosion, and enhancing water use efficiency. This study evaluates and compares selected infiltration models for estimating water infiltration rates in the Shillanat-iv irrigation scheme in northern Ethiopia. Soil samples were collected to determine textural classes using hydrometer soil texture analysis and the United States Department of Agriculture (USDA) textural triangle. The soil textural map of the study was created using the inverse distance weight interpolation technique in ArcGIS version 10.4. Infiltration rates were measured using the double-ring infiltrometer for five soil textures: clay loam, loam, sandy clay loam, clay, and sandy loam. Six infiltration models (Kostiakov, Modified Kostiakov, Revised Modified Kostiakov, Philip, Horton, and Novel) were employed and evaluated using statistical parameters. Model calibration and validation were conducted using data from 38 points within the study area. The parameter values of the infiltration models were optimized using SPSS statistical software using least-squares errors. The results showed that, Revised Modified Kostiakov, Modified Kostiakov, and Novel infiltration models demonstrated superior capability in estimating infiltration rates for clay loam, loam, and sandy loam soil textures, respectively. Horton's model outperformed other models in estimating infiltration rates for both sandy clay loam and clay soil textures. The appropriately fitted infiltration models can be utilized in designing the irrigation system to estimate the infiltration rate of soil textures within the selected irrigation scheme and at similar sites with comparable soil textures.

Electrothermal mineralization of per- and polyfluoroalkyl substances for soil remediation

Per- and polyfluoroalkyl substances (PFAS) are persistent and bioaccumulative pollutants that can easily accumulate in soil, posing a threat to environment and human health. Current PFAS degradation processes often suffer from low efficiency, high energy and water consumption, or lack of generality. Here, we develop a rapid electrothermal mineralization (REM) process to remediate PFAS-contaminated soil. With environmentally compatible biochar as the conductive additive, the soil temperature increases to >1000 °C within seconds by current pulse input, converting PFAS to calcium fluoride with inherent calcium compounds in soil. This process is applicable for remediating various PFAS contaminants in soil, with high removal efficiencies ( >99%) and mineralization ratios ( >90%). While retaining soil particle size, composition, water infiltration rate, and cation exchange capacity, REM facilitates an increase of exchangeable nutrient supply and arthropod survival in soil, rendering it superior to the time-consuming calcination approach that severely degrades soil properties. REM is scaled up to remediate soil at two kilograms per batch and promising for large-scale, on-site soil remediation. Life-cycle assessment and techno-economic analysis demonstrate REM as an environmentally friendly and economic process, with a significant reduction of energy consumption, greenhouse gas emission, water consumption, and operation cost, when compared to existing soil remediation practices.

Effects of gravel on the water infiltration process and hydraulic parameters of stony soil in the eastern foothills of Helan Mountain, China

The investigation into the impact of gravel on water infiltration process and hydraulic parameters in stony soil could offer a theoretical basis to enhance water availability in rocky mountain area. A one-dimensional vertical infiltration experiment was used in this study. Six groups of gravel content of 0% (CK), 10% (W1), 20% (W2), 30% (W3), 40% (W4) and 50% (W5) were established to explore the changes in the wetting front, cumulative infiltration volume and infiltration rate. Then the accuracy of four infiltration models in simulating soil water infiltration processes was evaluated. Finally, Hydrus-1D was used to perform numerical inversion of the soil water content after infiltration. The findings revealed that: (1) When the infiltration time reached 300 min, the wetting front of the W1, W2, W3, W4 and W5 treatments was 11.00%, 17.00%, 32.25%, 38.75% and 54.50% lower than CK, the cumulative infiltration volume was 29.80%, 38.97%, 45.62%, 54.74% and 73.17% lower than CK, and the stable infiltration rate was 50.98%, 52.94%, 66.67%, 68.63% and 86.27% lower than CK. (2) The soil–water infiltration processes were accurately described by the Horton model, the coefficient of determination (R2) > 0.935. (3) The simulation results of Hydrus-1D showed that with the increase of gravel content, the values of the retention water content (θr), saturated water content (θs), shape coefficient (n) and saturated hydraulic conductivity (Ks) were decreased, the values of the reciprocal of air-entry (α) were increased. The value of R2 was more than 0.894, the root mean square error (RMSE) and mean absolute error (MAE) were less than 2%, which demonstrated that the Hydrus-1D model exhibited superior capability in simulating the changes of water content in stony soil in rocky mountain area. The findings of this study demonstrated that gravel could decrease the water infiltration process and affect the water availability. It could provide data support for the water movement process of stony soil and rational utilization of limited water resources in mountainous area.

Overexpression of Nrf2 in bone marrow mesenchymal stem cells promotes B-cell acute lymphoblastic leukemia cells invasion and extramedullary organ infiltration through stimulation of the SDF-1/CXCR4 axis.

Tumor microenvironment (TME) represents the key factor inducing leukemia development. As stromal cells within the leukemia microenvironment, Bone Marrow Mesenchymal Stem Cells (BM-MSCs) can trigger leukemia progression under certain conditions. As a critical transcription factor, nuclear factor erythroid related factor 2 (Nrf2) can modulate antioxidant response and antioxidant enzyme gene expression, and prevent various oxidative changes. We previously identified a novel mechanism by which Nrf2 promotes leukemia resistance, providing a potential therapeutic target for the treatment of drug-resistant/refractory leukemias. However, the role of Nrf2 in BM-MSCs from B-cell acute lymphoblastic leukemia (B-ALL) patients has not been clearly reported. The present work focused on investigating the effect of Nrf2 overexpression within MSCs on leukemia cell invasion, extramedullary infiltration and proliferation as well as its downstream pathway. Through clinical sample detection, in vitro cell experiments and in vivo animal experiments, the role of Nrf2 within MSCs within adult B-ALL cell migration and invasion and its potential molecular mechanism was explored through transcriptome sequencing analysis, RT-PCR, Western blot, cell migration, cell invasion, lentivirus transfection and other experiments. Nrf2 was highly expressed in BM-MSCs from patients with B-ALL as well as in BM-MSCs co-cultured with leukemia cells. Overexpression of Nrf2 within MSCs significantly promoted leukemia cell migration, invasion and proliferation. The extramedullary organ infiltration rate in B-ALL model mice receiving the combined infusion of both cell types dramatically increased relative to that of leukemia cells alone, accompanied by the significantly shortened survival time. Mechanism study found that Nrf2 overexpression within MSCs promoted PI3K-AKT/ERK1/2 phosphorylation in the downstream pathway by activating SDF-1/CXCR4 axis, ultimately leading to extramedullary infiltration of leukemia cells. High Nrf2 expression with in MSCs enhances leukemia cell invasion and migration, which then accelerates infiltration in leukemic extramedullary organs. Targeting Nrf2 or inhibiting its downstream signal molecules may be the effective interventions for B-ALL patients treatment.

Tillage, crop residue management and nitrogen application impacts on soil properties under maize–wheat (Zea mays–Triticum aestivum) cropping system

Tillage intensity, crop residue retention and nitrogen application can significantly impact the soil properties and crop productivity. We studied the effect of tillage (deep tillage [DT] vs. shallow tillage [ST]) in main plots and residue management viz. conventional tillage without residue (CT-R), conventional tillage with residue (CT+R), minimum tillage without residue (MT-R) and minimum tillage with residue (MT+R) in sub plots and fertilizer-N at 75, 100 and 125% N (viz. N75, N100 and N125) in sub-sub plots. Field treatments were established in maize-wheat (Zea mays-Triticum aestivum) cropping system during 2016-2019 at two different locations in north-western India and were arranged in split-split plot design. The soil penetration resistance was significantly lower under deep tillage (3.4 to 3.7%) as compared to shallow tillage. CT+R recorded lowest penetration resistance as compared to other tillage and residue combinations but other soil properties like OC, available NPK, soil aggregation, infiltration rate did not differ significantly. The addition of crop residue both under minimum and conventional tillage significantly increased the soil microorganism count and dehydrogenase enzyme activity at both locations. CT-R recorded lowest microorganism count and dehydrogenase enzyme activity. The available soil nitrogen, microorganism count and dehydrogenase enzyme activity significantly increased with increasing nitrogen doses at both locations and were highest under 125% N level as compared to 75% and 100% levels. In both crops, the grain yield was not significantly affected by tillage and crop residue combinations while the different levels of nitrogen fertilizer significantly affected the grain yield. From soil health and sustainability point of view, CT+R treatment with 100% recommended dose of nitrogen in maize-wheat crop rotation seemed beneficial.

Soil hydro-physical variables and crop residues determinate runoff, soil loss, and glyphosate and AMPA concentration in the aqueous phase under simulated rainfall events.

Soil structural degradation and water erosion processes were observed even in no-tillage schemes in the Pampas region. Within these conservation systems, agrochemical application per hectare is one of the highest globally. Thus, this entails a serious risk of water contamination. The objectives of this study were to (1) test the hypothesis that the hydrological dynamics and sediment concentration related to surface runoff were conditioned by soil structure regardless of the presence of maize (Zea mays L.) crop residue and (2) assess the incidence of maize crop residue on glyphosate and aminomethylphosphonic acid (AMPA) concentration in runoff. The soil under study corresponded to Arroyo Dulce Series (Typic Argiudoll silty loam soil). Rain simulations were performed in the laboratory on undisturbed soil samples. Total runoff and infiltration rate were similar between treatments with C(+) and without C(-) maize crop residues (C(+) 1381.40mL and 14.27mm h-1, C(-): 1529.70mL and 21.67mm h-1). The C(-) treatments showed a higher sediment concentration than C(+) (1.58 and 0.42g 100mL-1, respectively). Glyphosate and AMPA average values in runoff were 15.9 and 33.9µg L-1. High variability of the hydro-physical properties and occurrence of soil structure, particularly platy ones, were detected. The hydrological variables were conditioned mainly by the occurrence of platy structures regardless of crop residue presence. Glyphosate concentration was increased in the first runoff event by the presence of corn residues, while AMPA concentrations were higher in the second runoff event in both residue treatments. In this study, maize residue on the soil surface protected the soil from sediment detachment but did not change runoff or infiltration. Thus, the implementation of agricultural management practices that promote vegetative residue cover has shown positive results to erosion.

Impact of ventilation system retrofitting on indoor air quality in a single-family building

Due to prolonged human occupancy within indoor environments, the quality of indoor air holds significant importance. This study evaluates the impact of retrofitting a ventilation system from natural to mechanical on indoor air quality (IAQ) in a bedroom during heating seasons in 2017/18 and 2020/21. Measurements were conducted before and after modernization to assess CO2 concentrations, temperature, humidity, particulate matter (PM) and bacterial and fungal aerosols levels indoors and outdoors. Results show a significant decrease in CO2 concentration (from 1000 ± 240 ppm to 806 ± 165 ppm) and relative humidity (from 53.0 ± 3.6 % to 28.2 ± 4.1 %) post-modernization. Notable reduction in CO2 concentrations averaging 20 % was recorded, thereby elevating air quality category from IDAIII to IDAII. Additionally, the study determined the infiltration coefficient for PM2.5, which increased from 0.48 under natural ventilation to 0.63 after retrofitting. PM2.5 concentrations increased indoors (from 23.49 ± 11.21 μg/m3 to 56.68 ± 13.47 μg/m3) due to higher infiltration rates with mechanical ventilation. Bioaerosol measurements indicate fluctuating concentrations, with bacterial aerosols peaking in the evening. The use of mechanical ventilation led to increased transport and dispersion of bacterial bioaerosols indoors. In contrast, this was not observed for fungal aerosols. Additionally, the study highlights limitations in ventilation filtration efficiency and recommends the installation of PM2.5 sensors to regulate airflow during periods of high outdoor PM2.5 concentrations. Overall, while mechanical ventilation improved some IAQ parameters, it posed challenges in controlling particulate matter infiltration, emphasizing the need for comprehensive ventilation strategies to ensure indoor air quality and occupants' well-being.

Quantitative evaluation of acid flow behavior in fractures and optimization of design parameters based on acid wormhole filtration losses

The technique of matrix acidification or acid fracturing is commonly utilized to establish communication with natural fractures during reservoir reconstruction. However, this process often encounters limitations due to filtration, which restricts the expansion of the primary acid-etching fracture. To address this issue, a computational model has been developed to simulate the expansion of an acid-etching wormhole by considering various factors such as formation process, injection duration, pressure build-up, and time-varying acid percolation rate. By analyzing the pumping displacement of acid-etching wormholes, this model provides valuable insights into the time-dependent quantities of acid percolation. It has been revealed that the filtration rate of acid-etching wormholes is strongly influenced by pumping displacement, viscosity, and concentration of the acid fluid used in stimulation as well as physical properties of the reservoir itself. Notably, viscosity plays a significant role in determining the effectiveness of acid fracturing especially in low-viscosity conditions. Acid concentration within 15% to 20% exhibits maximum impact on successful acid fracturing while concentrations below 15% or above 20% show no obvious effect. Furthermore, it was found that pumping displacement has a major influence on effective fracturing. However, beyond a certain threshold (> 5.0 m3/min), increased pumping displacement leads to slower etching distance for acids used in construction purposes. The simulation also provides real-time distribution analysis for acidity levels within eroded fractures during matrix-acidification processes and quantifies extent of chemical reactions between acids and rocks within these fractures thereby facilitating optimization efforts for design parameters related to matrix-acidification.

Assessment of hydropedological characteristics at medium-sized landslide sites in Manafwa catchment, Mount Elgon, Uganda

ABSTRACT Though strongly linked to landslides, hydropedological characteristics are inadequately investigated in Manafwa catchment. This study investigated hydropedological characteristics at medium landslide sites in Manafwa catchment. The design included 12 infiltration experiments that were conducted at each site. To determine the selected soil physical properties, composite soil samples were extracted from the infiltration sites for soil laboratory analysis. Soil cores were extracted to determine saturated hydraulic conductivity (Ksat) and bulk density. The observed high infiltration rates and rapid Ksat underscore the susceptibility of the studied sites to landslide hazards. Additionally, soil organic matter, clay content, and bulk density further contribute to the understanding of the hydropedological factors influencing landslide occurrences. These findings reveal the need for comprehensive investigations into hydropedological characteristics of other landslide categories to assist in landslide risk assessment and management strategies.

Enhancement of porous asphalt mixtures modified with various fibers and ethylene–vinyl acetate polymer

Porous asphalt mixture is conventional hot mix asphalt (HMA) with substantially decreased fines, which produces an open-graded mixture that enables the water to flow through an interconnected void space. Porous asphalt is a permeable system that has a lot of benefits. However, because of its open structure, the durability of this mixture decreases, and both its stability and resilient modulus are much lower compared to the dense conventional asphalt mixtures. Also, the high void percentage may lead to an increase in the draindown proportion. Fibers (cellulose or mineral) and polymer-modified binders are recommended for porous asphalt mixtures, especially in hot and moderate climates. The objective of this study is to improve the porous asphalt mixture's performance by using ethylene–vinyl acetate (EVA) polymer-modified bitumen. Two types of fibers (cellulose fibers and glass wool fibers) were used, separately to determine the control mixture. Four different proportions of EVA polymer were added to the bitumen (1%, 2%, 3%, and 4%) and Scanning Electron Microscopy (SEM) was used for better investigating of the bitumen microstructure, then The Marshall mix design was used to determine the optimum EVA content (OEC) for the porous asphalt mixture. Several performance tests were conducted to investigate the characteristics of the porous asphalt mixture, such as the infiltration rate, binder draindown, the wheel track and the cantabro abrasion tests. The findings of the study conclude that the addition of EVA polymer to the porous asphalt mixtures enhances the performance as it increases stability by 20.8% and the infiltration rate by 20.6%. It decreases binder draindown proportion by 33.3%, cantabro abrasion loss by 25.1% and the rut depth at 5,000 cycles and 10,000 cycles by 29.8% and 19.7%, respectively.

Design Constant Head Permeability Meter Digital: A Project-Based Learning Media

The permeability coefficient value is one of the most important parameters in soil mechanics. Quick, simple, and digital direct soil permeability tests in the field are needed to obtain data representing conditions. This research aims to create a portable soil permeability test tool based on microcontroller automation used as a project-based learning for Transportation Cadets peculiarly Palembang Aviation Polytechnic Cadets for new experiences of new learning circumstances. This research method based on the principle of permeability testing using the constant-head method by analyzing the requirements quantitatively. This principle uses water change level parameters, which are used to test the infiltration rate in sample soil. Furthermore, measurements of changes in water level are used by water leveling sensors and processed using Arduino Uno based on fuzzy logic with access to results via the web, tool design, and simulation using SIMULINK software. The results of designing a digital measuring instrument for permeability using the constant head method have been validated for its schematic circuit using SIMULINK and can work without error. In conclusion, a model based on Darcy's Law equation and constant head to find the permeability coefficient can be generated, which can then be a prototype of the tool. It concluded the design of constant head permeability meter digital is useful as project-based leaning media for the Palembang aviation polytechnic. Furthermore, the equipment design will be the first digital measuring tool for permeability coefficient using the constant head method. The design has advantage to measure the soil permeability coefficient at the airport in the fastest way.

Hydrological Response of Bamboo Plantations on Soil–Water Dynamics in Humid and Semi-Arid Coastal Region of Kenya

Soils and water are major resources that drive a country’s economy, and therefore should be conserved and utilized sustainably. However, in Kenya, these two resources are facing huge depletion and degradation due to anthropogenic factors and climate change. Bamboo species, especially on large plantations, can significantly alter ecological, hydrological, and biogeochemical processes in the long term. This study aimed to evaluate the effects of different species of bamboo and tree plantations on important soil–water processes like infiltration, bulk density, runoff, and soil loss in Kenya. The research was conducted at two sites (Gede in Arabuko Sokoke forest and at Baolala, in Kilifi County) managed by the Kenya Forestry Research Institute (KEFRI). The Arabuko Sokoke forest has a hot–humid coastal climate, while Baolala is a hot semi-arid area with little precipitation. The study involved measurement of soil–water infiltration rates using infiltrometers, installing runoff plots to quantify surface runoff and sediment loss, and analyzing soil properties like bulk density for growing periods for different bamboo and tree species. At the Gede forest site, the 30-year-old Thyrsostachys siamensis and Bambusa bambos plantations recorded the highest infiltration rates. Mature bamboo plantations of T. siamensis and B. bambos recorded higher infiltration rates compared to mature plantations of E. camaldulensis and G. arborea. It was observed that the bamboo plantations manifested lower soil bulk density compared to bare land, which recorded the highest bulk density. At Boalala, infiltration rates were significantly higher in the bamboo species compared to grassland and bare land. The painted bamboo (B. vulgaris vittata) had a slightly higher water infiltration rate compared to B. vulgaris. Runoff and erosion patterns reinforced the benefits of more mature bamboo plantations as well. There was a significant correlation between amount of runoff and collected soil loss through erosion. The data showed reductions in surface runoff volumes and sediment loss as the bamboo plantations aged compared to younger species. Therefore, by enhancing infiltration and reducing runoff and erosion, well-managed bamboo plantations can protect valuable soil resources, improve water recharge, and support sustainable land use over the long term. In conclusion, this study showed the strong potential of bamboo as a soil and water conservation tool in Kenya.