Radial Deformation Research Articles

Influence of Polypropylene Fiber on Concrete Permeability under Freeze-Thaw Conditions and Mechanical Loading.

Polypropylene fiber reinforcement is an effective method to enhance the durability of concrete structures. With the increasing public interest in the widespread use of polypropylene fiber reinforced concrete (PFRC), the necessity of evaluating the mechanism of polypropylene fiber (PF) on the permeability of concrete has become prominent. This paper describes the influence of PF on the concrete permeability exposed to freeze-thaw cycles under compressive and tensile stress. The permeability of PFRC under compressive and tensile loads is accurately measured by a specialized permeability setup. The permeability of PFRC under compressive and tensile loads, the volume change of PFRC under compressive load, and the relationship between compressive stress levels at minimum permeability and minimum volume points of PFRC are discussed. The results indicate that the addition of PF adversely affects the permeability of concrete without freeze-thaw damage and cracks. However, it decreases the permeability of concrete specimens exposed to freeze-thaw cycles and cracking. Under compressive load, the permeability of PFRC initially decreases slowly and follows by a significant increase as the compressive stress level increases. This phenomenon correlates with the volume change of the specimen. The compressive stress level of the minimum permeability point and compressive stress level of the minimum volume point of PFRC exhibit a linear correlation, with a fitted proportional function parameter γ ≈ 0.98872. Under tensile load, the permeability of PFRC increases gradually with radial deformation and follows by a significant increase. The strain-permeability curves of PFRC under loading are studied and consist of two stages. In stage I, the permeability of PFRC gradually decreases with the increase of strain under compressive load, while the permeability increases with the increase of strain under tensile load. In stage II, under compressive load, the permeability of PFRC increases with the increase of freeze-thaw cycles, whereas under tensile load, the permeability gradually decreases with the increase of freeze-thaw cycles. The reduction of PF on the permeability of PFRC under tensile load is greater than that under compressive load. In future research, the relationship between strain and permeability of PFRC can be integrated with its constitutive relationship between stress and strain to provide a reference for the application of PF in the waterproofing of concrete structures.

Исследование кинетики формообразования деталей сферического подшипника скольжения из коррозионно-стойких сталей, полученных объемной штамповкой пористых заготовок

Introduction. Spherical powder sliding bearings are widely used in various branches of mechanical engineering. Therefore, the development of a promising method of production of spherical sliding bearing parts from powders of corrosion-resistant steels with specified properties is an urgent task. Purpose of work: is to study the kinetics of forming during cold die forging of spherical sliding bearing parts from stainless steel powder blanks, and to assess the effect of the chemical composition of lubricants and the design of the pressing tool on the structure and properties of the bearing outer ring. Materials from sprayed powders of stainless chromium-nickel steels obtained by cold die forging of sintered blanks coated with lubricants are studied in the work. The following research methods were used: mechanical tensile testing, metallographic studies and cold die forging process simulation. Results and its discussion. It is revealed that the resistance and work of deformation, as well as the kinetics of forming of the outer ring of the spherical sliding bearing are influenced by chemical composition of powders and lubricants, microstructure and mechanical properties of the blank material, configurations of the end surfaces of punches. The top and bottom edges of the outer bearing are most intensively sealed when the punch faces are made with a chamfer angle of 30–40 degrees. With an increase in the relative strain degree by height up to 0.30–0.35 its residual porosity amounted to 0.5–2.0 %. The features of definition of strain state and calculation of strain energy in the implementation of the offered method and the choice of technological parameters of the cold die forging process of sliding bearings parts are shown. A simple method for calculating and experimentally determining the coefficient of contact friction in the process of cold die forging of porous stainless steel blanks is developed, which allows to establish the effect of lubricant composition on the strain resistance at different values of the degree of radial deformation and to develop optimal methods of cold die forging of porous blanks in the production of parts of different complexity.

Research on the temperature measurement point selection technology for multi-degree-of-freedom thermal error compensation of lathe spindle

Abstract In order to solve the problem of difficulty in selecting temperature measurement points caused by the inconsistent axial and radial thermal deformation trends of CNC lathes, a multi-degree-of-freedom joint point selection method is proposed. The Ant Colony Optimization (ACO) algorithm is employed to identify a combination of temperature measurement points. Based on this combination, thermal errors in both directions are modeled, with modeling accuracy serving as the condition for updating ant pheromones. The process iterates until the optimal temperature measurement point combination is determined. Experimental results demonstrate that the temperature measurement points selected using this method exhibit significantly improved fitting accuracy and stability for various operating conditions compared to traditional point selection methods.

Deep cardiac phenotyping by cardiovascular magnetic resonance reveals subclinical focal and diffuse myocardial injury in patients with psoriasis (PSOR-COR study).

Psoriasis vulgaris (PV) is a chronic inflammatory disorder frequently associated with cardiovascular disease (CVD). This study aims to provide a prospective tissue characterization in patients with PV without major CVD using cardiovascular magnetic resonance (CMR). Patients with PV underwent laboratory assessment, a 12-lead and 24-h ECG, and a CMR exam at a 1.5-T scanner. Scan protocol included assessment of left (LV) and right (RV) ventricular function and strain analysis, native and post-contrast T1 mapping, T2 mapping and late gadolinium enhancement (LGE). In total, 60 PV patients (median(IQR) age in years: 50.0 (36.0-60.8); 34 men (56.7%)) were recruited and compared to 40 healthy volunteers (age in years: 49.5 (37.3-57.8); 21 men (53.0%)). No differences were found regarding LV and RV function (p = 0.78 and p = 0.75). Global radial and circumferential strains were lower in patients (p < 0.001 and p < 0.001, respectively). PV had higher global T1 times (1001 (982-1026) ms vs. 991 (968-1005) ms; p = 0.01) and lower global T2 times (48 (47-49) ms vs. 50 (48-51) ms; p < 0.001); however, all values were within local reference ranges. Focal non-ischemic fibrosis was observed in 17 (28.3%) PV patients. Deep cardiac phenotyping by CMR revealed subclinical myocardial injury in patients with PV without major CVD, despite preserved LV and RV function. Diffuse and focal fibrosis might be the first detectable signs of adverse tissue remodeling leading to reduced circumferential and radial myocardial deformation. In the background of local and systemic immunomodulatory therapy, no signs of myocardial inflammation were detected. The exact impact of immunomodulatory therapies on the myocardium needs to be addressed in future studies. ISRCTN71534700.

The tidal deformation and atmosphere of WASP-12 b from its phase curve

Context. Ultra-hot Jupiters present a unique opportunity to understand the physics and chemistry of planets, their atmospheres, and interiors at extreme conditions. WASP-12 b stands out as an archetype of this class of exoplanets, with a close-in orbit around its star that results in intense stellar irradiation and tidal effects. Aims. The goals are to measure the planet’s tidal deformation, atmospheric properties, and also to refine its orbital decay rate. Methods. We performed comprehensive analyses of the transits, occultations, and phase curves of WASP-12b by combining new CHEOPS observations with previous TESS and Spitzer data. The planet was modeled as a triaxial ellipsoid parameterized by the second-order fluid Love number of the planet, h2, which quantifies its radial deformation and provides insight into the interior structure. Results. We measured the tidal deformation of WASP-12b and estimated a Love number of h2 = 1.55−0.49+0.45 (at 3.2σ) from its phase curve. We measured occultation depths of 333 ± 24 ppm and 493 ± 29 ppm in the CHEOPS and TESS bands, respectively, while the nightside fluxes are consistent with zero, and also marginal eastward phase offsets. Our modeling of the dayside emission spectrum indicates that CHEOPS and TESS probe similar pressure levels in the atmosphere at a temperature of ~2900 K. We also estimated low geometric albedos of Ag = 0.086 ± 0.017 and Ag = 0.01 ± 0.023 in the CHEOPS and TESS passbands, respectively, suggesting the absence of reflective clouds in the high-temperature dayside of the planet. The CHEOPS occultations do not show strong evidence for variability in the dayside atmosphere of the planet at the median occultation depth precision of 120 ppm attained. Finally, combining the new CHEOPS timings with previous measurements refines the precision of the orbital decay rate by 12% to a value of −30.23 ± 0.82 ms yr−1, resulting in a modified stellar tidal quality factor of Q′★ = 1.70 ± 0.14 × 105. Conclusions. WASP-12 b becomes the second exoplanet, after WASP-103b, for which the Love number has been measured from the effect of tidal deformation in the light curve. However, constraining the core mass fraction of the planet requires measuring h2 with a higher precision. This can be achieved with high signal-to-noise observations with JWST since the phase curve amplitude, and consequently the induced tidal deformation effect, is higher in the infrared.

Elastic-plastic response of tunnel in GZZ-based constitutive model

Investigating the stress redistribution characteristics after tunneling is critical for designing and constructing deeply buried tunnels. Three-dimensional stresses are more prominent in deep than in shallow tunnels, resulting in nonlinear strength. The generalized Zhang–Zhu (GZZ) criterion captures the nonlinear strength well. Therefore, this study established a 2D plane-strain numerical model using a GZZ-based constitutive model. The effects of the axial stress and rock properties on the stress redistribution and plastic zone are discussed. The initial axial stresses changed the axial stress distribution after excavation and had little effect on the radial and tangential stress distributions. The size of the plastic zone decreases with decreasing geological strength index and increasing rock mass mi . However, with increasing dilation coefficient, the stress distributions remained almost unchanged, whereas the radial deformation gradually increased.

Pressure-induced structural modifications of imogolite nanotubes and of their methylated analogues

Structural modifications of single-walled aluminosilicate clay nanotubes have been studied under hydrostatic pressure by in situ synchrotron X-ray scattering. Imogolite nanotubes (INT) of nominal composition (OH)3Al2O3SiOH, and methyl-modified imogolite nanotubes (m-INT), (OH)3Al2O3SiCH3, have hydrophilic and hydrophobic internal cavities, respectively. Nanotube chiralities also differ, with zigzag (INT) and armchair (m-INT) chirality. In this work, pressure-induced changes in nanotube morphology and atomic structure are studied as a function of chirality, affinity of the inner cavity, and the pressure-transmitting medium used. Radial deformation and collapse of nanotubes are evidenced below 3 GPa, followed by the formation of a lamellar phase at higher pressures. In the case of INT, the collapse pressure value depends on the pressure transmitting medium chosen. Axial compressibility is measured, and a pseudo Young's modulus Y is determined to be equal to ∼265 GPa for INT and below 80 GPa for m-INT, underpinning the role of nanotube chirality in mechanical properties.

Investigation of the Penetration Performance of the Radial Forging Process for Wrought Aluminium Alloy.

With the wide application potential of wrought aluminium alloy in aerospace, automobile and electronic products, high-quality aluminium bars prepared by the radial forging (RF) process have received extensive attention. Penetration performance refers to the depth of radial plastic deformation of forgings, which is the key factor in determining the quality of forging. In this work, the penetration performance of the radial forging process for 6063 wrought aluminium bars is investigated by simulation using FORGE software. The minimum reduction amount of the hammer is calculated based on the forging penetration theory of forging. The influence of process parameters including forging ratio (FR) and billet temperature on the effective stress and hammer load in the RF process are investigated. The RF-deformed billet is then produced with the optimal process parameters obtained from the simulation results. The average grain size of aluminium alloy semi-solid spherical material is used to evaluate the forging penetration. Simulation results showed that the effective strain at the edge and the centre of the RF-deformed billet gradually increases, but the increasing speed of the effective strain at the edge becomes low. The hammer load first decreases quickly and then gradually maintains stability by increasing the FR. It is found that low billet temperature and high FR should be selected as appropriate process parameters under the allowable tonnage range of RF equipment. Under an isothermal temperature of 630 °C and a sustaining time of 10 min, the difference in the average grain dimension between the edge and the centre positions of the starting extruded blank is 186.43 μm, while the difference in the average grain dimension between the edge and the centre positions of the RF-deformed blank is 15.09 μm. The improvement ratio of penetration performance for the RF-deformed blank is obtained as 91.19%.

Diagnosis of Radial Deformation and Axial Displacement Faults in Power Transformer Windings using X-ray and Compton Backscatter Imaging

Continuous and uninterrupted transmission and distribution of electrical energy is highly dependent on the flawless operation of power transformers. Failure of these critical components can lead to network power interruptions and consequently have severe detrimental consequences. Therefore, timely detection and diagnosis of power transformer faults is crucial not only to prevent the escalation of faults but also to minimize repair and maintenance costs. Conventional methods for inspecting windings faults have limitations such as the need to take the transformer out of service, unreliable results, and the addition of auxiliary devices inside the transformer, such as dielectric windows. In contrast, the proposed method in this paper utilizes a Compton Backscatter Imaging (CBI) or X-Ray Transmission (XRT) device located outside the transformer, eliminating the need for any additional equipment. This enables online scanning of any number of transformers to assess their health status and identify the type, extent, and progression of potential internal faults. Experimental results demonstrate the feasibility of the proposed method for detecting radial deformation and axial displacement and disk space variations faults of varying magnitudes and locations in both high-voltage and low-voltage windings of power transformers.

A Study on the Borehole Wall Stability Analysis and Slurry Ratio Optimization for Construction of Pile in Complex Marine Strata.

In order to address the issue of hole collapse, which frequently arises when boring piles are being constructed in intricate marine strata, this paper discusses the influence of the slurry ratio on the slurry performance as well as the mechanism of slurry wall protection. It performs this by means of theoretical analysis, laboratory ratio testing, engineering analogies, numerical simulation, and field testing. Our findings demonstrate that adding sodium polyacrylate and sodium carboxymethyl cellulose can enhance mud's viscosity, contribute to flocculation, and improve the connection between mud and soil layers. Refering similar engineering cases, three optimization schemes are proposed for achieving a mud ratio that offers wall protection in complex marine strata. Furthermore, the particle flow model of slurry viscous fluid is established. The collapse of holes in the sand layer is reflected in the uneven radial displacement of hole walls and the invasion of mud particles. Increasing the viscosity of mud gradually transforms the uneven radial deformation of pore walls in the sand layer into a uniform radial deformation, whereas increasing the proportion of mud significantly decreases the radial displacement of hole walls. Additionally, when the mud pressure in the hole is 300 kPa and 600 kPa, the wall protection effect is better, and there is no particle penetration by substances such as sand. It is found that a high mud pressure can promote the diffusion of mud particles into the sand layer, while low mud pressure cannot balance the pressure on deep soil. The results of the field tests show that the ratio of water-clay-bentonite-CMC-Na-sodium carbonate = 700:110:90:1.5:0.5 used (where the mass percentage of each material is 77.8% water, 12.2% clay, 10% bentonite, 0.16% CMC-Na, and 0.05% sodium carbonate) can effectively prevent hole collapse and reduce the thickness of the sand layer at the bottom of the hole by 50%.

Experimental Investigation of a Free-Form Honed Cylinder Liner for Heavy-Duty Engines

For future internal combustion engines, driven by regenerative fuels, efficiency is more important than ever. One approach to reduce the losses inside the piston cylinder unit (PCU) is to improve the alignment of the liner and the piston. Therefore, a cylinder liner with a free form was developed at the Institute of Technical Combustion (ITV) of the Leibniz University Hannover which compensates radial and linear deformations along the stroke. The layout is based on a FEM simulation. The liner was manufactured by the Institute of Production Engineering and Machine Tools (IFW) of Leibniz University of Hannover with a novel turn-milling process. The liner was investigated on the heavy-duty Floating-Liner engine of ITV with a displacement of 1991 ccm and a bore diameter of 130 mm. The experimental results show improvement in the friction losses over the whole engine map in the range of 9% and up to 17.3% compared to a serial liner. Sealing efficiency could be improved up to 28.8%, depending on the operational point. Overall, the investigation aims for lower fuel consumption which would in result fewer emissions.

Modeling of self-gravitating compact configurations using radial metric deformation approach

This study analyzes new analytical solution types that explore the influence of complexity on time-independent, spherically symmetric astrophysical configurations, based on a radial metric deformation scheme also known as minimal geometric deformation. We demonstrate that the complexity factor, a scalar function obtained via splitting the Riemann tensor orthogonally, exhibits an additive property. This implies that the overall complexity of a system containing two interacting fluid distributions (represented by Tμν and Φμν) is simply the sum of the individual complexities of each fluid. This work employs the radial metric deformation approach, a powerful tool for constructing astrophysically viable models of anisotropic matter, by building upon the Vaidya–Tikekar and Finch–Skea relativistic spacetimes. We observe that both the metric ansatzes produce qualitatively similar features, though the magnitudes may vary slightly, for any non-zero value of the decoupling parameter (0≤α<1). Interestingly, both models preserve their anisotropic nature despite reaching the zero-complexity limit (α=1). Finally,we delve into the physical implications of these novel solution types, examining their potential to accurately represent real compact configurations.

Characterization of Potting Epoxy Resins Performance Parameters Based on a Viscoelastic Constitutive Model.

To describe the evolution of residual stresses in epoxy resin during the curing process, a more detailed characterization of its viscoelastic properties is necessary. In this study, we have devised a simplified apparatus for assessing the viscoelastic properties of epoxy resin. This apparatus employs a confining cylinder to restrict the circumferential and radial deformations of the material. Following the application of load by the testing machine, the epoxy resin sample gradually reduces the gap between its surface and the inner wall of the confining cylinder, ultimately achieving full contact and establishing a continuous interface. By recording the circumferential stress-strain on the outer surface of the confining cylinder, we can deduce the variations in material bulk and shear moduli with time. This characterization spans eight temperature points surrounding the glass transition temperature, revealing the bulk and shear relaxation moduli of the epoxy resin. Throughout the experiments, the epoxy resin's viscoelastic response demonstrated a pronounced time-temperature dependency. Below the glass transition temperature, the stress relaxation response progressively accelerated with increasing temperature, while beyond the glass transition temperature, the stress relaxation time underwent a substantial reduction. By applying the time-temperature superposition principle, it is possible to construct the relaxation master curves for the bulk and shear moduli of the epoxy resin. By fitting the data, we can obtain expressions for the constitutive model describing the viscoelastic behavior of the epoxy resin. In order to validate the reliability of the test results, a uniaxial tensile relaxation test was conducted on the epoxy resin casting body. The results show good agreement between the obtained uniaxial relaxation modulus curves and those derived from the bulk and shear relaxation modulus equations, confirming the validity of both the device design and the testing methodology.

Electromagnetic field on the complexity of minimally deformed compact stars

In the context of this endeavor, we establish a simple protocol for formulating interior stellar solutions that exhibit spherically symmetric configurations against the backdrop of relativistic gravitational decoupling through radial metric deformation (minimal geometric deformation scheme). In this pursuit, we make use of the vanishing complexity factor (Y~TF\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\widetilde{Y}_{TF}$$\\end{document}) condition, based on Herrera’s (Phys Rev D 97, 044010, 2018) innovative concept regarding the complexity of static or slowly evolving spherical matter configurations. The idea of a complexity factor emerges as the outcome of the orthogonal splitting of the Riemann–Christoffel tensor, which yields different scalar functions, known as structure scalars. The protocol is demonstrated by employing the Buchdahl and Tolman relativistic stellar ansatzes as isotropic seeds. Both of these ansatzes exhibit similar physical features, with a minor variation in their magnitudes in the case of Y~TF≠0\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\widetilde{Y}_{TF}\ e 0$$\\end{document}, where 0≤α<1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$0\\le \\alpha <1$$\\end{document}, and α\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\alpha $$\\end{document} represents a coupling parameter. However, when Y~TF=0\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\widetilde{Y}_{TF}=0$$\\end{document}, the Buchdahl stellar ansatz exhibits a uniform density matter configuration, while the Tolman model features an increasing pressure profile. The obtained relativistic stellar models satisfy the basic viability constraints required for the physically realistic configurations.

Thermohyperelastic constitutive response for semilinear materials with application to deformation of a rotating thin disk

Constitutive modeling of soft elastomers is a well researched subject due to its numerous engineering applications. This study derives a thermodynamically consistent constitutive model for semilinear thermoelastic solids for which the strain energy density depends on the deformation gradient through the Biot stretch tensor. The Frechet derivatives, Coleman-Noll procedure, and product decomposition-based technique are employed to formulate the constitutive model. The combination of the derived model and thermomechanical field equations is specialized for application to problem of radial deformation of a rotating thin disk. The formulated model provides simple closed-form expressions for simulating thermomechanical responses of solids. Under suitable conditions, the derived three-configuration-based constitutive model reduces to the two-configuration-based constitutive equations. Finally, and among other things, the numerical solutions illustrate the effects of angular speed of rotation on thermal stress and displacement fields at points within the radially deforming rotating disk.

A Three-Dimensional Deformation Monitoring Method: Combining Optical Deformation Monitoring Based on Regression Models and GB-SAR Interferometry.

This paper introduces a method for quantifying the three-dimensional deformation of ground targets and outlines the associated process. Initially, ground-based synthetic aperture radar was employed to monitor the radial deformation of targets, and optical equipment monitored pixel-level deformation in the vertical plane of the line of sight. Subsequently, a regression model was established to transform pixel-level deformation into two-dimensional deformation based on a fundamental length unit, and the radar deformation monitoring data were merged with the optical deformation monitoring data. Finally, the fused data underwent deformation, resulting in a comprehensive three-dimensional deformation profile of the target. Through physical data acquisition experiments, the comprehensive three-dimensional deformation of targets was obtained and compared with the actual deformations. The experimental results show that the method has a relative error of less than 10%, and monitoring accuracy is achieved at the millimeter level.

Establishing Ohmic Contact of a Radial Compressed CNT Bundle with High Work Function Metal.

Establishing low-resistance ohmic contact is critical for developing electronic devices based on traditional silicon and new low-dimensional materials. Due to unprecedented electronic and mechanical properties, the one-dimensional carbon nanotubes (CNTs) have been used as source/drain, gate, or tunnel to fabricate transistors. However, the mechanism causing low-resistance ohmic contact is not clear yet. Here, the hybrid atomic force microscopy-scanning electron microscopy (AFM-SEM) instrument was developed to establish lower-resistance ohmic contact between a radial compressed deformed multiwalled CNT bundle and high work function metal (platinum and gold). The radial compression structure under strong van der Waals attraction was in situ characterized through the SEM image to obtain the diameter and width and through AFM to get height and to perform nanoindentation, indicating that Pt has the smaller radial compression deformation. Molecular dynamics simulations exhibit that compared to Pt, a wider ribbon-like graphene layer formed when the radial compressed CNTs contacted with Au. The bond forming and electron orbital overlapping between C atoms of deformed CNTs and the high work function metal atom is beneficial for good electrical contact.

High resolution and large measurement range voltage sensing based on an optoelectronic oscillator utilizing an unbalanced Mach-Zehnder interferometer.

A voltage sensor with high resolution and large measurement range based on an optoelectronic oscillator (OEO) is proposed and experimentally demonstrated. The key component in the cavity to select the oscillating signal is a finite impulse response (FIR)-microwave photonic filter (MPF) which consists of a sinusoidal broadband optical signal, an unbalanced Mach-Zehnder interferometer (MZI), a section of dispersion compensating fiber, and a photodetector. The center frequency of the FIR-MPF is mainly determined by the free spectral range (FSR) of the FIR-MPF. In the lower arm of the MZI, a cylindrical piezoelectric ceramic (PZT) wrapped with a section of optical fiber acts as voltage sensing head. Due to the inverse piezoelectric effect of PZT, the variation of the voltage will cause radial deformation of the cylindrical PZT and then lead to the change of the FSR of the MZI, determining the shift of center frequency of FIR-MPF as well as the frequency of the oscillating signal of the OEO. Thus, by monitoring the shift of the oscillation frequency of the OEO using an electric spectrum analyzer or a digital signal processor, a high-speed interrogation and high-resolution voltage measurement can be realized. Additionally, in the proposed scheme, an infinite impulse response (IIR)-MPF consisting of a fiber ring resonator is cascaded with the FIR-MPF to ensure the single-mode oscillation of the OEO. The experimental results show that a total range of 1700 V voltage sensing from - 200 V to 1500 V is accomplished with the voltage sensitivity of 0.25 GHz/100 V and the resolution of 0.3 V. By adjusting the proportion of the length of single mode fiber between two branches of MZI, the impact of temperature can be greatly reduced. The proposed sensor offers advantages such as a large measurement range, high resolution, high-speed interrogation, and stability to temperature disturbances, making it highly suitable for sensing applications in smart grids.

Optimization and experiment research of the cylinder block of the roller piston pump

The roller piston pump is a new type of axial piston pump. The pump has the advantages of high limiting speed, low noise, and vibration compared to the traditional axial piston pump. However, the structure and flow channel of the cylinder block of the roller piston pump are more complicated. When the cylinder block is subjected to high hydraulic pressure, its radial compressive deformation is large, which will lead to wear of the cylinder block and distribution shaft. For this problem, the paper will optimize the structural parameters of the cylinder block. Eight key parameters of the cylinder block are selected as the design variables, and the maximum radial deformation and mass of the cylinder block are taken as the optimization objectives. The central composite design method is used to generate 81 sets of sample data, and the second-order response surface model is obtained by regression analysis. The optimal structural parameters of the cylinder block are obtained through multi-objective optimization, and the material of the cylinder block is optimized. Finally, an experiment bench was built for experimental validation, and the efficiency of the pump was further investigated. The optimization results show that the maximum compression deformation of the inner diameter surface of the cylinder block decreases from 15.865 to 4.903 µm, and the mass of the cylinder block increases from 434.951 to 489.892 g. The experimental results show that the load-bearing pressure of the optimized roller piston pump increases from less than 15 to 35 MPa, and compared with the traditional axial piston pump, there is an increase in both mechanical efficiency and volumetric efficiency.

Influence of temperature and preload force on capacitance and electromechanical impedance of lead zirconate titanate piezoelectric wafer active sensors for structural health monitoring of bolts

This study focuses on the effect of temperature and preload force on capacitance and electromechanical impedance of lead zirconate titanate piezoelectric wafer active sensors for structural health monitoring of bolts. We explain the influence of temperature on the basis of the phenomenological thermodynamic theory of ferroelectricity by Landau, Ginsburg and Devonshire. The article illustrates the effect of damping the radial deformation of piezoelectric sensors on the capacitance and electromechanical impedance spectra in structural health monitoring of bolts. We also explains the similarities between the effects of temperature and preload force on the electromechanical impedance spectra. We establish a clear correlation between the mechanical strain in the region of the sensor (here due to a preload force), the capacitance and the electromechanical impedance spectra and thus show that piezoelectric sensors made of lead–zirconate–titanate can be used excellently in areas of variable mechanical strain. The article enhances the understanding of the measurement method and facilitates the transfer of the measurement method to other problems in structural health monitoring. Furthermore, the acquired knowledge serves as a solid basis for verifying the plausibility of data sets containing electromechanical impedance spectra.