Quasi-static Mechanical Tests Research Articles

Study on dynamic mechanical properties and microstructure of basalt fiber reinforced coral sand cement composite *

This study investigates the impact of basalt fiber on the static and dynamic compression of coral-sand cement-based composites, as well as the mechanisms for strengthening and toughening. The samples of basalt fiber-reinforced coral sand cementitious composite (BFRCSCC) with varying fiber volume fractions (0%, 0.2%, 0.4%, 0.6%, 0.8%) underwent quasi-static mechanical tests and impact dynamic tests using an MTS universal testing machine and a split Hopkinson pressure bar (SHPB). This study investigates the mechanical properties of BFRCSCC, focusing on static and dynamic compressive strength, dynamic stress-strain curve, strain rate effect, failure strain, toughness analysis, and energy dissipation mechanism. In terms of microstructure, specimens of BFRCSCC were tested using scanning electron microscopy (SEM). The results indicate that basalt fiber can significantly enhance the quasi-static compressive strength (fc)and dynamic compressive strength (fd)of coral sand cement-based composite materials. When the basalt fiber content is 0.4%, the static and dynamic compressive strength of BFRCSCC increases by 28.78% and 37.25% respectively compared to ordinary concrete. The analysis from a micro perspective indicates that the incorporation of basalt fiber in the concrete matrix enhances the hydration reaction between cement and the BFRCSCC interface. The spatial structure formed by basalt fiber contributes to the excellent toughening effect on the mechanical properties of BFRCSCC. As the content of basalt fiber increases (≤0.4%), the bridging effect becomes stronger. The dynamic increase factor (DIF) and toughness index of BFRCSCC exhibit a significant positive correlation with the strain rate effect. Basalt fibers can help drive the hydration products to fill the cracks or voids in the cement matrix, thereby increasing the material's density and enhancing the impact resistance of coral concrete. This can be utilized in practical engineering projects with high dynamic load demands.

Biomechanical characterization of the passive porcine stomach

The complex mechanics of the gastric wall facilitates the main digestive tasks of the stomach. However, the interplay between the mechanical properties of the stomach, its microstructure, and its vital functions is not yet fully understood. Importantly, the pig animal model is widely used in biomedical research for preliminary or ethically prohibited studies of the human digestion system. Therefore, this study aims to thoroughly characterize the mechanical behavior and microstructure of the porcine stomach. For this purpose, multiple quasi-static mechanical tests were carried out with three different loading modes, i.e., planar biaxial extension, radial compression, and simple shear. Stress-relaxation tests complemented the quasi-static experiments to evaluate the deformation and strain-dependent viscoelastic properties. Each experiment was conducted on specimens of the complete stomach wall and two separate layers, mucosa and muscularis, from each of the three gastric regions, i.e., fundus, body, and antrum. The significant preconditioning effects and the considerable regional and layer-specific differences in the tissue response were analyzed. Furthermore, the mechanical experiments were complemented with histology to examine the influence of the microstructural composition on the macrostructural mechanical response and vice versa. Importantly, the shear tests showed lower stresses in the complete wall compared to the single layers which the loose network of submucosal collagen might explain. Also, the stratum arrangement of the muscularis might explain mechanical anisotropy during tensile tests. This study shows that gastric tissue is characterized by a highly heterogeneous microstructure with regional variations in layer composition reflecting not only functional differences but also diverse mechanical behavior. Statement of SignificanceUnfortunately, only few experimental data on gastric tissue are available for an adequate material parameter and model estimation. The present study therefore combines layer- and region-specific stomach wall mechanics obtained under multiple loading conditions with histological insights into the heterogeneous microstructure. On the one hand, the extensive data sets of this study expand our understanding of the interplay between gastric mechanics, motility and functionality, which could help to identify and treat associated pathologies. On the other hand, such data sets are of high relevance for the constitutive modeling of stomach tissue, and its application in the field of medical engineering, e.g., in the development of surgical staplers and the improvement of bariatric surgical interventions.

Orientation-dependent plasticity mechanisms control synergistic property improvement in dynamically deformed metals

We demonstrate the ability to synergistically enhance strength and toughness in metals by tailoring the dominant plasticity mechanisms from impact-induced heterogeneous nanostructures. Using a laser-induced projectile impact testing apparatus, we impact initially dislocation-free single crystal microcubes at high velocities to induce grain size and dislocation density gradients. These gradient nanostructures exhibit heterogeneous deformation under subsequent quasi-static loading leading to enhanced strength and toughness. Transmission Kikuchi diffraction (TKD) analyses show that the synergistic property improvement arises from the complimentary intragranular and intergranular plasticity mechanisms: the pronounced intragranular dislocation plasticity within coarse grained regions provides increased strain hardening and toughness while the nanograined regions with high dislocation densities provide high strength and supplemental toughness enhancement through cooperative grain rotation and grain boundary migration. These plasticity mechanisms are activated to different extents depending on the specific impact-induced nanostructures, which depend on the orientation of the single crystal upon impact. Controlled [100]-face, [110]-edge, and [111]-corner impact of single crystal microcubes, subsequent quasi-static mechanical testing, and pre- and post-compression nanostructural characterization provide a fundamental understanding of the comprehensive process-structure-property relations in heterogeneous nanostructured metals.

Microstructure engineering of fusion zone in resistance spot welding of martensitic stainless steels: The role of Ni interlayer thickness

Martensitic stainless steel (MSS) spot welds show low fracture toughness due to the formation of a brittle microstructure at the joint area. To realize the full advantage of this class of steels in industrial applications, the strategy of altering the microstructure of the weld nugget through introduction of a Ni interlayer was investigated. For this purpose, Ni interlayers with variable thicknesses of 50 to 400 μm were utilized. The microstructural evolutions were thoroughly scrutinized using Scheil-Gulliver solidification modeling and electron backscatter diffraction (EBSD) analysis. Conventional quasi-static mechanical tests, namely, tensile-shear (TS) and cross-tension (CT) were used to correlate microstructure-mechanical properties relationships. In the absence of Ni interlayer, the weld nugget was predominantly composed martensite-M and presumably residual delta ferrite-δ (M+ δ-95%) phases with minor amounts of austenite-γ (5%), failing to meet the minimum peak load requirements under TS and CT loading conditions. By applying Ni interlayers of 50 and 75 μm, a noticeable increase in the fraction of austenite phase (up to 31%) in the weld nugget was detected; nevertheless, a slight to moderate improvement in the mechanical properties was observed since the solidification mode was still primary δ, and M+δ were still the predominant phases in the microstructure. A significant improvement in mechanical properties was achieved in 100 μm Ni interlayer owing to change in the solidification mode from primary δ to γ along with the formation of a mainly austenitic microstructure. However, due to the incomplete mixing of melted base metals and Ni interlayer, a different microstructure consisting of M, δ and γ was also occasionally perceptible in the weld nugget of this sample. The best mechanical properties in terms of strength and ductility occurred with increasing thickness to 200 μm and above, which coincided with the formation of a fully austenitic microstructure in the entire weld nugget.

The mechanical and microstructural response of single crystal aluminium to one dimensional shock loading: The effects of orientation

A series of plate impact experiments have been performed on the three principal orientations of single crystal aluminium: [100], [110] and [111]. Experiments were designed to probe the Hugoniot Elastic Limit, spall strength and Equation of state as well as understand the microstructural response, via transmission electron microscopy, Transmission Kikuchi Diffraction and mechanical testing of shocked material. Results from this work, show that orientation affects the HEL and spall strength in a similar manner to the quasi-static uniaxial stress compressive response, with [100] and [110] being similar and [111] significantly stronger. This correlates with expectations from considerations using the Schmid analysis. However we have noted that similar studies in copper yield a different ordering of the HELs. We have reconciled those differences using an analysis based on second order elastic constants. However the shocked microstructures and post shock quasi-static mechanical response are strongly influenced by orientation. The [100] orientation shows a response typical of high stacking fault face centred cubic metals, consisting of equiaxed subgrains and a strong post shock hardening during quasi-static mechanical testing, similar to results in polycrystalline aluminium. In contrast, the [110] and [111] orientations have a microstructural response more similar to polycrystalline aluminium after repeated shock loading excursions, combined with much lower post shock hardening during mechanical testing. This suggests that these orientations require much greater dislocation activity to achieve the same plastic deformation as [100]. This would appear to agree with the much higher degree of work hardening observed in these orientations compared to [100].

Predictive Modeling of Soft Stretchable Nanocomposites Using Recurrent Neural Networks

Human skin is characterized by rough, elastic, and uneven features that are difficult to recreate using conventional manufacturing technologies and rigid materials. The use of soft materials is a promising alternative to produce devices that mimic the tactile capabilities of biological tissues. Although previous studies have revealed the potential of fillers to modify the properties of composite materials, there is still a gap in modeling the conductivity and mechanical properties of these types of materials. While traditional Finite Element approximations can be used, these methodologies tend to be highly demanding of time and processing power. Instead of this approach, a data-driven learning-based approximation strategy can be used to generate prediction models via neural networks. This paper explores the fabrication of flexible nanocomposites using polydimethylsiloxane (PDMS) with different single-walled carbon nanotubes (SWCNTs) loadings (0.5, 1, and 1.5 wt.%). Simple Recurrent Neural Networks (SRNN), Long Short-Term Memory (LSTM), and Gated Recurrent Units (GRU) models were formulated, trained, and tested to obtain the predictive sequence data of out-of-plane quasistatic mechanical tests. Finally, the model learned is applied to a dynamic system using the Kelvin-Voight model and the phenomenon known as the bouncing ball. The best predictive results were achieved using a nonlinear activation function in the SRNN model implementing two units and 4000 epochs. These results suggest the feasibility of a hybrid approach of analogy-based learning and data-driven learning for the design and computational analysis of soft and stretchable nanocomposite materials.

Impact Tests and Computed Tomography Scans of Prismatic Battery Cells

Recently, the use of prismatic cells in electric vehicles has increased significantly. Unlike the cylindrical or pouch format, the prismatic cell format has not been sufficiently investigated. In this study, quasi-static mechanical tests are performed on prismatic cells. The tests include a cylindrical and a hemispherical impactor that mechanically load the cells in all three spatial directions. In both in-plane directions, a cell stack consisting of three cells is tested to capture the influence and loading of the outer cells of a cell stack. It is found out that, in the in-plane tests, short-circuiting occurs first in the outer cells and subsequently in the middle cell, which is targeted by the impactor. This result can also be supported by computed tomography scans. The results illustrate that, when evaluating the crash safety of battery cells, several cells should always be tested in order to capture the different loading of the cells.

New Sensing and Radar Absorbing Laminate Combining Structural Damage Detection and Electromagnetic Wave Absorption Properties

Within the paradigm of smart mobility, the development of innovative materials aimed at improving resilience against structural failure in lightweight vehicles and electromagnetic interferences (EMI) due to wireless communications in guidance systems is of crucial relevance to improve safety, sustainability, and reliability in both aeronautical and automotive applications. In particular, the integration of intelligent structural health monitoring and electromagnetic (EM) shielding systems with radio frequency absorbing properties into a polymer composite laminate is still a challenge. In this paper, we present an innovative system consisting of a multi-layered thin panel which integrates nanostructured coatings to combine EM disturbance suppression and low-energy impact monitoring ability. Specifically, it is composed of a stack of dielectric and conductive layers constituting the sensing and EM-absorbing laminate (SEAL). The conductive layers are made of a polyurethane paint filled with graphene nanoplatelets (GNPs) at different concentrations to tailor the effective electrical conductivity and the functionality of the material. Basically, the panel includes a piezoresistive grid, obtained by selectively spraying onto mylar a low-conductive paint with 4.5 wt.% of GNPs and an EM-absorbing lossy sheet made of the same polyurethane paint but properly modified with a higher weight fraction (8 wt.%) of graphene. The responses of the grid's strain sensors were analyzed through quasi-static mechanical bending tests, whereas the absorbing properties were evaluated through free-space and waveguide-based measurement techniques in the X, Ku, K, and Ka bands. The experimental results were also validated by numerical simulations.

Biomechanical Tests on Long-Bone Elliptical Medullary-Canal Endoprostheses for Limb Salvage in Dogs.

Exo-endoprosthesis is a limb salvage procedure poorly described for animals, as only expensive metal devices have been used so far. Currently, additive manufacturing (AM) can make this type of implant affordable by exploring a wide new range of materials. However, safety factors should be considered and could be related to kinetic and kinematic studies of canine natural gaits. The suitability of a novel inner part of an exo-endoprosthesis manufactured by fuse deposition modeling (FDM) was assessed for long canine bones with an elliptical medullary canal. Polyether ether ketone (PEEK) was the material used as an alternative to metal for veterinary traumatology. Poisson's ratio of 3D-printed PEEK material and ex vivo mechanical tests of the customized endoprosthesis were performed for the evaluation. The customized endoprostheses had promising outcomes for the radii of 20 kg dogs. Quasistatic mechanical tests of bone-inserted endoprostheses-pure compression tests-reached a maximum force of 1045.0 ± 78.0 N. In fatigue tests, the samples reached 500,000 cycles without failure or detriment to their quasistatic results. These outcomes surpass the natural weight-bearing of dogs, even during a galloping pace. Furthermore, torque tests with different adhesives were performed to obtain reference data for future assessments comparing with natural dog movements.

Aging damage mechanism and mechanical properties degradation of 3D orthogonal woven thermoset composites subjected to cyclic hygrothermal environment

3D orthogonal woven thermoset composites (3DOWCs) can be applied to fabricate the bearing structures of supersonic aircrafts due to their excellent mechanical properties. However, 3DOWCs would be subjected to the cyclic hygrothermal aging caused by the specific service environment of supersonic aircrafts. This paper aims to reveal the cyclic hygrothermal aging mechanism and the consequent degradations of mechanical properties of 3DOWCs. Accelerated hygrothermal cyclical ageing tests were carried out in a simulated service environment of supersonic aircrafts. The aging damage mechanisms were investigated with moisture content monitoring, micromorphology observation and Fourier transform infrared (FTIR) analysis. The evolution of mechanical properties was evaluated by quasi-static mechanical tests (tension, compression and interlaminar shear) and Dynamic mechanical analysis (DMA). The results show that the mechanical properties of 3DOWCs deteriorate significantly with the increasing of hygrothermal aging cycle. Interface debonding, crack propagation, and embrittlement of fiber bundles are the main reasons of the degradation.

Biomechanical Test of a New Endoprosthesis for Cylindrical Medullary Canals in Dogs.

Exo-endoprosthesis is a limb salvage procedure for animals, although only expensive metal devices have been described. Now-a-days, new materials for this type of implant could be considered due to novel and affordable manufacturing techniques. However, a factor of safety (FoS) should be considered. There are kinetic and kinematic studies of canine natural gaits, which can be used to establish an FoS for mechanical tests for new non-metallic devices. Polyetheretherketone (PEEK) is used in different specialties in human medicine. Its mechanical properties (and its close mechanical stiffness to that of bone) make this polymer an alternative to metals in veterinary traumatology. PEEK could also be used in 3D printing. The suitability of a novel inner part of an exo-endoprosthesis manufactured by fuse deposition modeling (FDM) was presented in this study for long canine bones. Mechanical characterization of 3D-printed PEEK material and ex vivo mechanical tests of a customized endoprosthesis were performed to address it. Young's modulus of 3D-printed PEEK suffered a reduction of 30% in relation to bulk PEEK. Customized 3D-printed PEEK endoprostheses had promising outcomes for the tibiae of 20 kg dogs. Pure compression tests of the non-inserted endoprostheses showed a maximum force of 936 ± 199 N. In the bending tests of non-inserted endoprostheses, the PEEK part remained intact. Quasistatic mechanical tests of bone-inserted endoprostheses (compression-bending and pure compression tests) reached a maximum force of 785 ± 101 N and 1,642 ± 447 N, respectively. In fatigue tests, the samples reached 500,000 cycles without failure or detriment to their quasistatic results. These outcomes surpass the natural weight-bearing of dogs, even during a galloping pace. In conclusion, the 3D-printed PEEK part of the endoprosthesis for an exo-endoprosthesis can withstand loading, even during a galloping pace.

Fused Filament Fabrication 3D printed polypropylene/ alumina nanocomposites: Effect of filler loading on the mechanical reinforcement

Three-dimensional (3D) printed Polypropylene (PP) reinforced with aluminum oxide (Al2O3) nanoparticles (NPs) were developed and fully characterized in this study. Nanocomposite filaments were produced initially following a melt mixing extrusion process, utillised as feedstock for the Fused Filament Fabrication (FFF) specimen manufacturing. Al2O3 NPs at 0.5, 1.0, 2.0 and 4.0 wt% loadings were melt-mixed with the PP thermoplastic matrix. Specific geometry samples were 3D printed and analysed via tensile, flexural, viscoelastic, impact, microhardness and fractographic investigations. Raman spectroscopy verified the polymeric structure and the incorporated Al2O3 NPs within the polymer matrix. Atomic Force Microscopy (AFM) of the extruded filaments revealed the nanoscale roughness induced by the alumina nanoinclusions. All 3D printed nanocomposite structures exhibited enhanced tensile, flexural and thermomechanical properties. Specifically, the best combination was found for the 1.0 wt% loaded specimen showing a tensile and flexural strength increase by approx. 4% and 19%, respectively, with a concomitant slight increase in impact and microhardness properties compared to unfilled PP. Dynamic Mechanical Analysis (DMA) revealed a stiffening mechanism for the PP/Al2O3 nanocomposites being in good agreement with the quasi-static mechanical tests. It could be envisaged that the 3D printed PP/Al2O3 nanocomposites developed herein could find numerous applications as engineered thermoplastics, where enhanced material's static and dynamic mechanical properties are required.

Influence of anodizing surface treatment on the aging behavior in salt-fog environment of aluminum alloy 5083 to fiber reinforced composites adhesive joints

ABSTRACT The present work aims to evaluate how an innovative and eco-friendly anodizing process with tartaric-sulfuric acid (TSA) bath and a pore widening in an aqueous solution of NaOH 0.1 M can improve the durability in marine environment of co-cured adhesive joints between an aluminum alloy (AA 5083) and fiber (i.e., glass or basalt)-reinforced composite substrates. The aging was carried out by exposing samples to salt-fog spray conditions (5 wt.% NaCl) for 30, 60 and 90 days in a climate chamber, in accordance with ASTM B117. In order to get further insights on the aging behaviour of bonded joints, neat matrix was also exposed to the same environment for 60 days. Quasi-static mechanical tests and morphological analysis through SEM microscope coupled with EDX analyser were carried out to deeper understand how the fracture surfaces change during aging and how this affected the mechanical performances of joints.

Vibrometry as a noncontact alternative to dynamic and viscoelastic mechanical testing in cartilage.

Physiological loading of knee cartilage is highly dynamic and may contribute to the progression of osteoarthritis. Thus, an understanding of cartilage's dynamic mechanical properties is crucial in cartilage research. In this study, vibrometry was used as a fast (2 h), noncontact and novel alternative to the slower (30 h), traditional mechanical and biochemical assays for characterization of cartilage from the condyle, patella, trochlear groove and meniscus. Finite-element models predicted tissue resonant frequencies and bending modes, which strongly correlated with experiments (R2 = 0.93). Vibrometry-based viscoelastic properties significantly correlated with moduli from stress relaxation and creep tests, with correlation strengths reaching up to 0.78. Loss modulus also strongly correlated with glycosoaminoglycan (GAG) content. Dynamic properties measured by vibrometry significantly differed among various knee cartilages, ranging between 6.1 and 56.4 MPa. Interestingly, meniscus viscoelastic properties suggest that contrary to common belief, it may lack shock absorption abilities; instead, condylar hyaline cartilage may be a better shock absorber. These data demonstrate for the first time that vibrometry is a noncontact approach to dynamic mechanical characterization of hyaline and fibrocartilage cartilage with concrete relationships to standard quasi-static mechanical testing and biochemical composition. Thus, with a single tool, vibrometry greatly facilitates meeting multiple regulatory recommendations for mechanical characterization of cartilage replacements.

IN VITRO MECHANICAL EVALUATION OF SPINAL FIXATION ROD CONNECTORS

ABSTRACT Objective Evaluate and compare the mechanical resistance and the fatigue behavior associated with the use of three different modalities of vertebral fixation system rod connectors through in vitro pre-clinical mechanical tests developed specifically for this application (linear, lateral with square connector and lateral with oblique connector). Methods Cobalt chromium rods 5.5 mm in diameter were used and coupled with three types of connectors: a) side rod with oblique connector, b) side rod with square connector, and c) rod and linear connectors. Quasi-static mechanical four-point bending and fatigue tests were performed. The variables measured were (I) the bending moment at the yield limit, (II) the displacement at the yield limit, (III) the rigidity of the system in flexion and (IV) the number of cycles until system failure. Results The linear system presented the greatest force and the greatest moment at the yield limit, as well as the greatest stiffness equivalent to bending. All specimens with square and oblique connectors endured 2.5 million cycles in the minimum and maximum conditions of applied moment. The specimens with linear connector endured 2.5 million cycles with fractions of 40.14% of the bending moment at the yield limit, but failed with levels of 60.17% and 80.27%. Conclusions Systems with linear connectors showed greater mechanical resistance when compared to systems with square and oblique connectors. All systems supported cyclic loads that mimic in vivo demands. Level of evidence V; In vitro research.

Strength and elastic properties of 3D printed PVDF-based parts for lightweight biomedical applications

Research results on 3D printed fluoropolymers are scarce since the filaments were introduced commercially only in the last several years to enable fused filament fabrication (FFF) of structural components for more demanding service conditions, where chemical, UV or fire resistance, high purity, sterilizability or biocompatibility are critical such as in biomedical industry. This experimental study reports on additive manufacturing and quasi-static mechanical testing of polyvinylidene fluoride (PVDF) and in-vitro cytocompatible polyvinylidene fluoride-co-hexafluoropropylene (PVDF-HFP) specimens that were 3D printed with different infill patterns at 75% density (linear, cubic, cross, concentric, octet, zigzag, triangular). Recommendations are provided for addressing issues related to weak adhesion and obtrusive warping, which occur in open-chamber FFF printer due to semi-crystalline and hydrophobic nature of PVDF-based thermoplastics. The measured tensile and flexural stress-strain curves are analyzed to determine the influence of strut-based infills on the strength and elastic performance by including comparisons in ratios between strength, modulus of elasticity and weight of the specimens. The concentric pattern demonstrates the highest tensile strength, while the cross and triangular lattices – the lowest one. In three-point bending, the linear pattern delivers the lowest strength, while the rest exhibit comparable mechanical properties. The results are conducive to the design of 3D printable PVDF homopolymer and copolymer load-bearing structures serving as lightweight high-performance components in biomedical applications.

In-plane quasi-static and out-of-plane dynamic behavior of nanofiber interleaved glass/epoxy composites and finite element simulation

Eight-ply glass/epoxy composites interleaved by electrospun Polysulfone (PSF) nanofibers were manufactured by vacuum-assisted hand lay-up method. The effect of nanofibrous interlaminar layers on the mechanical performance of laminated composites was investigated under both in-plane quasi-static and out-of-plane low-velocity impact (LVI) test conditions. Low-velocity impact responses of reference and nanofiber interleaved composite laminates were modeled by LS-Dyna finite element (FE) code for numerical simulations. The results of the quasi-static mechanical tests show that PSF nanofiber interleaving increases the tensile and compressive strength by 10.5% and 25.5%, respectively. PSF nanofibers played an important role in improving the impact damage resistance of composite laminates with increasing impact energy levels. The low-velocity impact tests results indicated that PSF nanofibers decreased the fiber breakage area at 20 J and 30 J energy levels by about 26% and 28%, respectively. Besides, PSF nanofiber interleaving improved damage threshold load values by 4.8%, 15.2%, and 23% at 10 J, 20 J, and 30 J energy levels, respectively. Experimental and FE simulation results were comparatively presented in terms of force–time, force–deflection, and energy-time curves. A good agreement was achieved between experimental and simulation results.

An equine tendon model for studying intra-tendinous shear in tendons that have more than one muscle contribution

Human Achilles tendon is composed of three smaller sub-tendons and exhibits non-uniform internal displacements, which decline with age and after injury, suggesting a potential role in the development of tendinopathies. Studying internal sliding behaviour is therefore important but difficult in human Achilles tendon. Here we propose the equine deep digital flexor tendon (DDFT) and its accessory ligament (AL) as a model to understand the sliding mechanism. The AL-DDFT has a comparable sub-bundle structure, is subjected to high and frequent asymmetric loads and is a natural site of injury similar to human Achilles tendons. Equine AL-DDFT were collected and underwent whole tendon level (n=7) and fascicle level (n=7) quasi-static mechanical testing. Whole tendon level testing was performed by sequentially loading through the proximal AL and subsequently through the proximal DDFT and recording regional strain in the free structures and joined DDFT and AL. Fascicle level testing was performed with focus on the inter-sub-bundle matrix between the two structures at the junction. Our results demonstrate a significant difference in the regional strain between the joined DDFT and AL and a greater transmission of force from the AL to the DDFT than vice versa. These results can be partially explained by the mechanical properties and geometry of the two structures and by differences in the properties of the interfascicular matrices. In conclusion, this tendon model successfully demonstrates that high displacement discrepancy occurs between the two structures and can be used as an easy-access model for studying intra-tendinous shear mechanics at the sub-tendon level. Statement of significanceOur study provides a naturally occurring and easily accessible equine model to study the complex behaviour of sub-tendons within the human Achilles tendon, which is likely to play a critical role in the pathogenesis of tendon disease. Our results demonstrate that the difference in material stiffness between the equine AL and DDFT stems largely from differences in the inter-fascicular matrix and furthermore that differences in strain are maintained in distal parts of the tightly joined structure. Furthermore, our results suggest that distribution of load between sub-structures is highly dependent on the morphological relationship between them; a finding that has important implications for understanding Achilles tendon mechanical behaviour, injury mechanisms and rehabilitation.

Creep and Residual Properties of Filament-Wound Composite Rings under Radial Compression in Harsh Environments.

This work focuses on the viscoelastic response of carbon/epoxy filament-wound composite rings under radial compressive loading in harsh environments. The composites are exposed to three hygro-thermo-mechanical conditions: (i) pure mechanical loading, (ii) mechanical loading in a wet environment and (iii) mechanical loading under hygrothermal conditioning at 40 C. Dedicated equipment was built to carry out the creep experiments. Quasi-static mechanical tests are performed before and after creep tests to evaluate the residual properties of the rings. The samples are tested in (i) radial compression, (ii) axial compression, and (iii) hoop tensile strength. Different laminates wound at off-axis orientations are manufactured via filament winding and analyzed. Key results show that creep displacement is affected by both hygrothermal and mechanical conditionings, especially at a higher temperature. Moreover, residual properties are quantified showing that creep generates permanent damage in the cylinders.

Investigation of Bimodal Aluminium Matrix Syntactic Foams Filled with Ceramic Hollow Spheres

Abstract In this study bimodal A413 matrix syntactic foams filled with ceramic hollow spheres (CHSs) were produced and examined by computer tomography (CT) and quasi-static mechanical testing to determine the mixing properties of the hollow spheres and the strength of the metal foam. Two hollow spheres of different nominal diameters (d1 = 2.4 mm and d2 = 7.0 mm) were used in equal volume ratio. The produced metal foams have a density of 1.61±0.03 g/cm3, with smaller inclusions and some defective hollow spheres in the structure. The foams have an average compressive strength of 120 MPa and a specific mechanical energy absorbing capacity of 43.5 J/cm3. As a result of the upsetting tests, the matrix material is separated from the CHSs, breaking the connection between them.