Properties Of Trabecular Bone Research Articles

Quasi-static and dynamic mechanical properties of a linoleic acid-modified, low-modulus bone cement for spinal applications

Background Polymethylmethacrylate (PMMA) bone cement is extensively used in spinal procedures such as vertebroplasty and kyphoplasty, while its use in percutaneous cement discoplasty (PCD) is not yet widely spread. A main issue for both application sites, vertebra and disc, is the mismatch in stiffness between cement and bone, potentially resulting in adjacent vertebral fractures and adjacent segment disease. Tailoring the cement modulus using additives is hence an interesting strategy. However, there is a lack of data on the tensile and tension-compression fatigue properties of these cements, relevant to the newly researched indication of PCD. Method A commercial PMMA cement (VS) was modified with 12%vol of linoleic acid (VSLA) and tested for quasi-static tensile properties. Additionally, tension-compression fatigue testing with amplitudes ranging from +/-5MPa to +/-7MPa and +/-9MPa was performed, and a Weibull three-parameter curve fit was used to calculate the fatigue parameters. Results Quasi-static testing revealed a significant reduction in VSLA’s Young’s Modulus (E=581.1±126.4MPa) compared to the original cement (E=1478.1±202.9MPa). Similarly, the ultimate tensile stress decreased from 36.6±1.5MPa to 11.6±0.8MPa. Thus, VSLA offers improved compatibility with trabecular bone properties. Fatigue testing of VSLA revealed that as the stress amplitude increased the Weibull mean number decreased from 3591 to 272 and 91 cycles, respectively. In contrast, the base VS cement reached run-out at the highest stress amplitude. However, the lowest stress amplitude used exceeds the pressures recorded in the disc in vivo, and VSLA displayed a similar fatigue life range to that of the annulus fibrosis tissue. Conclusions While the relevance of fully reversed tension-compression fatigue testing can be debated for predicting cement performance in certain spinal applications, the results of this study can serve as a benchmark for comparison of low-modulus cements for the spine. Further investigations are necessary to assess the clinical feasibility and effectiveness of these cements.

Investigation of the Role of Osteoporotic Vertebra Degeneration on the Stability of the Lumbar Spine: In Silico Modelling under Compressive Loading.

An evaluation of the impact of osteoporosis on loss of spinal stability, with or without intervertebral disc degeneration, using computational analysis is presented. The research also investigates the correlation between osteoporosis and intervertebral disc degeneration. Three-dimensional finite element models of human lumbar spine segments were used to assess the influence of osteoporosis on spinal stability. Five different models of age-related degeneration were created using various material properties for trabecular bone and intervertebral discs. Calculation results indicate that in a spine with osteoporosis, the deformation of the intervertebral discs can increase by more than 30% when compared to a healthy spine. Thus, intervertebral disc deformation depends not only on the degree of degeneration of the discs themselves, but their deformation is also influenced by the degree of osteoporosis of the vertebrae. Additionally, the load-bearing capacity of the spine can decrease by up to 30% with osteoporosis, regardless of the degree of intervertebral disc deformation. In conclusion, osteoporosis can contribute to intervertebral disc degeneration.

Finite Element Analysis of a Rib Cage Model: Influence of Four Variables on Fatigue Life during Simulated Manual CPR.

Cardiopulmonary resuscitation (CPR) is a life-saving technique used in emergencies when the heart stops beating, typically involving chest compressions and ventilation. Current adult CPR guidelines do not differentiate based on age beyond infancy and childhood. This oversight increases the risk of fatigue fractures in the elderly due to decreased bone density and changes in thoracic structure. Therefore, this study aimed to investigate the correlation and impact of factors influencing rib fatigue fractures for safer out-of-hospital manual cardiopulmonary resuscitation (OHMCPR) application. Using the finite element analysis (FEA) method, we performed fatigue analysis on rib cage models incorporating chest compression conditions and age-specific trabecular bone properties. Fatigue life analyses were conducted on three age-specific rib cage models, each differentiated by trabecular bone properties, to determine the influence of four explanatory variables (the properties of the trabecular bone (a surrogate for the age of the subject), the site of application of the compression force on the breastbone, the magnitude of applied compression force, and the rate of application of the compression force) on the fatigue life of the model. Additionally, considering the complex interaction of chest compression conditions during actual CPR, we aimed to predict rib fatigue fractures under conditions simulating real-life scenarios by analyzing the sensitivity and interrelation of chest compression conditions on the model's fatigue life. Time constraints led to the selection of optimal analysis conditions through the use of design of experiments (DOE), specifically orthogonal array testing, followed by the construction of a deep learning-based metamodel. The predicted fatigue life values of the rib cage model, obtained from the metamodel, showed the influence of the four explanatory variables on fatigue life. These results may be used to devise safer CPR guidelines, particularly for the elderly at a high risk of acute cardiac arrest, safeguarding against potential complications like fatigue fractures.

Mimicking the mechanical properties of cortical bone with an additively manufactured biodegradable Zn-3Mg alloy

Additively manufactured (AM) biodegradable zinc (Zn) alloys have recently emerged as promising porous bone-substituting materials, due to their moderate degradation rates, good biocompatibility, geometrically ordered microarchitectures, and bone-mimicking mechanical properties. While AM Zn alloy porous scaffolds mimicking the mechanical properties of trabecular bone have been previously reported, mimicking the mechanical properties of cortical bone remains a formidable challenge. To overcome this challenge, we developed the AM Zn-3Mg alloy. We used laser powder bed fusion to process Zn-3Mg and compared it with pure Zn. The AM Zn-3Mg alloy exhibited significantly refined grains and a unique microstructure with interlaced α-Zn/Mg2Zn11 phases. The compressive properties of the solid Zn-3Mg specimens greatly exceeded their tensile properties, with a compressive yield strength of up to 601 MPa and an ultimate strain of >60 %. We then designed and fabricated functionally graded porous structures with a solid core and achieved cortical bone-mimicking mechanical properties, including a compressive yield strength of >120 MPa and an elastic modulus of ≈20 GPa. The biodegradation rates of the Zn-3Mg specimens were lower than those of pure Zn and could be adjusted by tuning the AM process parameters. The Zn-3Mg specimens also exhibited improved biocompatibility as compared to pure Zn, including higher metabolic activity and enhanced osteogenic behavior of MC3T3 cells cultured with the extracts from the Zn-3Mg alloy specimens. Altogether, these results marked major progress in developing AM porous biodegradable metallic bone substitutes, which paved the way toward clinical adoption of Zn-based scaffolds for the treatment of load-bearing bony defects. Statement of significanceOur study presents a significant advancement in the realm of biodegradable metallic bone substitutes through the development of an additively manufactured Zn-3Mg alloy. This novel alloy showcases refined grains and a distinctive microstructure, enabling the fabrication of functionally graded porous structures with mechanical properties resembling cortical bone. The achieved compressive yield strength and elastic modulus signify a critical leap toward mimicking the mechanical behavior of load-bearing bone. Moreover, our findings reveal tunable biodegradation rates and enhanced biocompatibility compared to pure Zn, emphasizing the potential clinical utility of Zn-based scaffolds for treating load-bearing bony defects. This breakthrough opens doors for the wider adoption of zinc-based materials in regenerative orthopedics.

Automated region growing-based segmentation for trabecular bone structure in fresh-frozen human wrist specimens

Bone strength depends on both mineral content and bone structure. Measurements of bone microstructure on specimens can be performed by micro-CT. In vivo measurements are reliably performed by high-resolution peripheral computed tomography (HR-pQCT) using dedicated software. In previous studies from our research group, trabecular bone properties on CT data of defatted specimens from many different CT devices have been analyzed using an Automated Region Growing (ARG) algorithm-based code, showing strong correlations to micro-CT.The aim of the study was to validate the possibility of segmenting and measuring trabecular bone structure from clinical CT data of fresh-frozen human wrist specimens. Data from micro-CT was used as reference. The hypothesis was that the ARG-based in-house built software could be used for such measurements.HR-pQCT image data at two resolutions (61 and 82 µm isotropic voxels) from 23 fresh-frozen human forearms were analyzed. Correlations to micro-CT were strong, varying from 0.72 to 0.99 for all parameters except trabecular termini and nodes. The bone volume fraction had correlations varying from 0.95 to 0.98 but was overestimated compared to micro-CT, especially at the lower resolution. Trabecular separation and spacing were the most stable parameters with correlations at 0.80-0.97 and mean values in the same range as micro-CT.Results from this in vitro study show that an ARG-based software could be used for segmenting and measuring 3D trabecular bone structure from clinical CT data of fresh-frozen human wrist specimens using micro-CT data as reference. Over-and underestimation of several of the bone structure parameters must however be taken into account.

Method for accurate removal of trabecular bone samples from a curved articulating surface of the distal femur

BackgroundKnowing the mechanical properties of trabecular bone is critical for many branches of orthopaedic research. Trabecular bone is anisotropic and the principal trabecular direction is usually aligned with the load it transmits. It is therefore critical that the mechanical properties are measured as close as possible to this direction, which is often perpendicular to a curved articulating surface. Methods: This study presents a method to extract trabecular bone cores perpendicular to a curved articulating surface of the distal femur. Cutting guides were generated from computed tomography scans of 12 human distal femora and a series of cutting tools were used to release cylindrical bone cores from the femora. The bone cores were then measured to identify the angle between the bone core axis and the principal trabecular axis. FindingsThe method yielded an 83% success rate in core extraction over 10 core locations per distal femur specimen. In the condyles, 97% of extracted cores were aligned with the principal trabecular direction. InterpretationThis method is a reliable way of extracting trabecular bone specimens perpendicular to a curved articular surface and could be useful across the field of orthopaedic research.

Advancing 3D Dental Implant Finite Element Analysis: Incorporating Biomimetic Trabecular Bone with Varied Pore Sizes in Voronoi Lattices.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional computer- aided design (CAD) models fail to fully represent the bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTOP 4.17.3 and Creo Parametric 8.0 software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking in to account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced FEA improves the biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

Compression properties of cellular iron lattice structures used to mimic bone characteristics

Recently, cellular materials made by the repetition of unit cells, that is, iron lattices have become appealing to mimic the structure of bone. The aim of the study is to choose the most adequate lattice structures, which have the compressive mechanical properties closer to the ones of bone, in the perspective of their use as temporary implants. Five types of unit cells were selected, such as, cubic (C), truncated octahedron (TO), truncated cubic (TC), rhombicuboctahedron (RCO), and rhombitrucated cuboctahedron (RTCO). The mechanical properties were assessed by numerical simulations with a finite-element analysis. The size effect was studied with the comparison of results among samples with different numbers of unit cells. Simulations covered a wide range of relative densities. Graded dense-in and dense-out configurations were constructed with lattices of types RTCO and TO, being the unit cells, themselves graded. Lattice structures RTCO and TO were found to be stable at every relative density studied, while C, TC and RCO lattices are unstable at low densities. The evaluation of size effects was not conclusive, which could be biased by other factors. The Young's modulus of RTCO and TO lattices enable to reproduce the properties of both trabecular and cortical bone, with an appropriate choice of the relative density. To mimic trabecular bone, only RTCO and TO structures with low relative densities, can be used, while arrangements of C, TC and RCO cells can only replicate the properties of cortical bone. Graded cells may have the same properties as non-graded with lower density.

Long-Term Effects of Reproduction and Lactation on the Rat Supraspinatus Tendon and Proximal Humerus.

During pregnancy and breastfeeding, women undergo hormonal fluctuations required for fetal development, parturition, and infant growth. These changes have secondary consequences on the maternal musculoskeletal system, increasing the risk for joint pain and osteoporosis. Though hormone levels return to prepregnancy levels postpartum, women may experience lasting musculoskeletal pain. Sex disparities exist in the prevalence of musculoskeletal disorders, but it remains unclear how reproductive history may impact sex differences. Specifically, the effects of both reproductive history and sex on the rotator cuff have not been studied. Pregnancy and lactation affect bone microstructure, suggesting possible impairments at the enthesis of rotator cuff tendons, where tears commonly occur. Therefore, our objective was to evaluate how reproductive history affects sex differences of the supraspinatus tendon and proximal humerus using male, virgin female, and female rats with a history of reproduction (referred to as reproductive females). We hypothesized tendon mechanical properties and humeral bone microstructure would be inferior in reproductive females compared to virgin females. Results showed sex differences independent of reproductive history, including greater tendon midsubstance modulus but lower subchondral bone mineral density (BMD) in females. When considering reproductive history, reproductive rats exhibited reduced tendon insertion site modulus and trabecular bone micro-architecture compared to virgin females with no differences from males. Overall, our study identified long-term changes in supraspinatus tendon mechanical and humeral trabecular bone properties that result following pregnancy and lactation, highlighting the importance of considering reproductive history in investigations of sex differences in the physiology and pathology of rotator cuff injuries.

Mechanical and Computational Fluid Dynamic Models for Magnesium-Based Implants.

Today, mechanical properties and fluid flow dynamic analysis are considered to be two of the most important steps in implant design for bone tissue engineering. The mechanical behavior is characterized by Young's modulus, which must have a value close to that of the human bone, while from the fluid dynamics point of view, the implant permeability and wall shear stress are two parameters directly linked to cell growth, adhesion, and proliferation. In this study, we proposed two simple geometries with a three-dimensional pore network dedicated to a manufacturing route based on a titanium wire waving procedure used as an intermediary step for Mg-based implant fabrication. Implant deformation under different static loads, von Mises stresses, and safety factors were investigated using finite element analysis. The implant permeability was computed based on Darcy's law following computational fluid dynamic simulations and, based on the pressure drop, was numerically estimated. It was concluded that both models exhibited a permeability close to the human trabecular bone and reduced wall shear stresses within the biological range. As a general finding, the proposed geometries could be useful in orthopedics for bone defect treatment based on numerical analyses because they mimic the trabecular bone properties.

A graph model to describe the network connectivity of trabecular plates and rods.

Introduction: The trabecular network is perceived as a collection of interconnected plate- (P) and rod-like (R) elements. Previous research has highlighted how these elements and their connectivity influence the mechanical properties of bone, yet further work is required to elucidate better the deeply interconnected nature of the trabecular network with distinct element formations conducting forces per their mechanical boundary conditions. Within this network, forces act through elements: a rod or plate with force applied to one end will transmit this force to a component connected to the other end, defining the boundary conditions for the loading of each element. To that end, this study has two aims: First, to investigate the connectivity of individually segmented elements of trabecular bone with respect to their local boundary conditions as defined by the surrounding trabecular network and linking them directly to the bone's overall mechanical response during loading using a mathematical graph model of the plate and rod (PR) Network. Second, we use this model to quantify side artifacts, a known artifact when testing an excised specimen of trabecular bone, where vertical trabeculae lose their load-bearing capacity due to a loss of connectivity, ultimately resulting in a change of the trabecular network topology. Resuts: Connected elements derived from our model predicted apparent elastic modulus by fitting a linear regression (R 2 = 0.81). In comparison, prediction using conventional bone volume fraction results in a lower accuracy (R 2 = 0.72), demonstrating the ability of the PR Network to estimate compressive elastic modulus independent of specimen size or loading boundary condition. Discussion: PR Network models are a novel approach to describing connectivity within the trabecular network and incorporating mechanical boundary conditions within the morphological analysis, thus enabling the study of intrinsic material properties of trabecular bone. Ultimately, PR Network models may be an early predictor or provide further insights into osteo-degenerative diseases.

Treatment with PB125® Increases Femoral Long Bone Strength in 15-Month-Old Female Hartley Guinea Pigs.

Nuclear factor-erythroid 2-related factor-2 (Nrf2) is a transcription factor that serves as a master regulator of anti-inflammatory agents, phase I xenobiotic, and phase II antioxidant enzymes, all of which provide a cytoprotective role during disease progression. We hypothesized that oral administration of a purported phytochemical Nrf2-activator, PB125®, would increase long bone strength in aging Hartley guinea pigs, a model prone to musculoskeletal decline. Male (N = 56) and female (N = 56) guinea pigs were randomly assigned to receive daily oral treatment with either PB125® or vehicle control. Animals were treated for a consecutive 3-months (starting at 2-months of age) or 10-months (starting at 5-months of age) and sacrificed at 5-months or 15-months of age, respectively. Outcome measures included: (1) ANY-maze™ enclosure monitoring, (2) quantitative microcomputed tomography, and (3) biomechanical testing. Treatment with PB125® for 10months resulted in increased long bone strength as determined by ultimate bending stress in female Hartley guinea pigs. In control groups, increasing age resulted in significant effects on geometric and structural properties of long bones, as well as a trending increase in ultimate bending stress. Furthermore, both age and sex had a significant effect on the geometric properties of both cortical and trabecular bone. Collectively, this work suggests that this nutraceutical may serve as a promising target and preventive measure in managing the decline in bone mass and quality documented in aging patients. Auxiliary to this main goal, this work also capitalized upon 5 and 15-month-old male and female animals in the control group to characterize age- and sex-specific differences on long bone geometric, structural, and material properties in this animal model.

Quasi-static and dynamic mechanical properties of a low-modulus bone cement for spinal applications

Background Polymethylmethacrylate (PMMA) bone cement is extensively used in spinal procedures such as vertebroplasty and kyphoplasty, while its use in percutaneous cement discoplasty (PCD) is not yet widely spread. A main issue for both application sites, vertebra and disc, is the mismatch in stiffness between cement and bone, potentially resulting in adjacent vertebral fractures and adjacent segment disease. Tailoring the cement modulus using additives is hence an interesting strategy. However, there is a lack of data on the tensile and tension-compression fatigue properties of these cements, relevant to the newly researched indication of PCD. Method A commercial PMMA cement (VS) was modified with 12%vol of linoleic acid (VSLA) and tested for quasi-static tensile properties. Additionally, tension-compression fatigue testing with amplitudes ranging from +/-5MPa to +/-7MPa and +/-9MPa was performed, and a Weibull three-parameter curve fit was used to calculate the fatigue parameters. Results Quasi-static testing revealed a significant reduction in VSLA’s Young’s Modulus (E=581.1±126.4MPa) compared to the original cement (E=1478.1±202.9MPa). Similarly, the ultimate tensile stress decreased from 36.6±1.5MPa to 11.6±0.8MPa. Thus, VSLA offers improved compatibility with trabecular bone properties. Fatigue testing of VSLA revealed that as the stress amplitude increased the Weibull mean number decreased from 3591 to 272 and 91 cycles, respectively. In contrast, the base VS cement reached run-out at the highest stress amplitude. However, the lowest stress amplitude used exceeds the pressures recorded in the disc in vivo, and VSLA displayed a similar fatigue life range to that of the annulus fibrosis tissue. Conclusions While the relevance of fully reversed tension-compression fatigue testing can be debated for predicting cement performance in certain spinal applications, the results of this study can serve as a benchmark for comparison of low-modulus cements for the spine. Further investigations are necessary to assess the clinical feasibility and effectiveness of these cements.

THU426 Randomized Controlled Trial Comparing The Efficacy Of Teriparatide, Zoledronate And Denosumab In Postmenopausal Women With Type 2 Diabetes Mellitus At High Risk Of Fragility Fractures: 6-month Interim Analysis Of HR-pQCT Parameters

Abstract Disclosure: R. Pal: None. T.N. Prasad: None. S.K. Bhadada: None. V. Singla: None. S. Ram: None. N. Aggarwal: None. A. Kumar: None. People with type 2 diabetes (T2D) are at high-risk of fragility fractures, however, there are no randomised controlled trials (RCTs) evaluating the efficacy/safety of anti-osteoporosis drugs as a primary endpoint in T2D (1). To address this lacuna, we conducted a pilot prospective, open-labeled, blinded-end point (PROBE) RCT (CTRI/2022/02/039978) wherein consecutive postmenopausal female (≥ 50 years) with T2D (duration ≥ 5 years) were screened. Subjects with HbA1c 7-10%, eGFR > 45 ml/min/1.73 m2 and prior history of vertebral (clinical/morphometric), hip, radius, humeral fragility fracture or at high-risk of fragility fractures [defined as areal bone mineral density (BMD) T-score (adjusted for diabetes) at lumbar spine/femoral neck ≤ -2.5 and high FRAX score] and without any secondary cause of osteoporosis were randomised in staggered fashion in a 1:1:1:1 ratio to receive either daily teriparatide, yearly zoledronate, biannually denosumab (in addition to standard of care, i.e., calcium 1000 mg/day and cholecalciferol 1000 IU/day) or only standard of care (control). The primary end points were change in areal BMD and frequency of incident fractures at 18 months. The secondary end point was change in HR-pQCT parameters measured at distal radius and distal tibia (XtremeCT II, SCANCO Medical AG, Switzerland) at 6 and 18 months.Out of 412 participants who were screened, 104 subjects were randomized to any of the 4 arms. Out of these 104 subjects, 53 have completed 6 months of follow-up (teriparatide n=14, zoledronate n=14, denosumab n=15, control n=10). There were no statistically significant differences in age, HbA1c, eGFR, calcium, phosphate, alkaline phosphatase, 25-hydroxyvitamin D, parathyroid hormone, procollagen type I N-propeptide (PINP), C-terminal telopeptide (CTX), areal BMD, trabecular bone score (TBS), FRAX score or HR-pQCT parameters between the 4 groups at randomisation. At 6 months, there was no significant difference in HbA1c between the 4 groups; PINP and CTX rise was significantly higher in teriparatide arm compared to zoledronate, denosumab or control arms. With regard to HR-pQCT, there were no statistically significant differences in total [total volumetric BMD (vBMD), bone volume fraction], cortical (vBMD, thickness, porosity, pore diameter), or trabecular (vBMD, thickness, number, separation) bone properties at the distal radius and distal tibia between the 4 arms at 6 months of follow-up. To conclude, zoledronate, denosumab or teriparatide were unable to induce any significant microarchitectural changes than standard of care in postmenopausal women with T2D at high-risk of fragility fractures following 6 months of treatment. Longer duration of treatment and follow-up of the cohort is required to arrive at robust conclusions. Reference: (1) Pal et al., Bone fragility in type 2 diabetes mellitus: a lot left to explore. Nat Rev Endocrinol. 2022;18:651-651 Presentation: Thursday, June 15, 2023

Numerical Analysis Applying the Finite Element Method by Developing a Complex Three-Dimensional Biomodel of the Biological Tissues of the Elbow Joint Using Computerized Axial Tomography

Numerical analysis computational programs are applied to the research of biological tissues, which have complex forms. Continuous technological advance has facilitated the development of biomodels to evaluate biological tissues of different human body systems using computerized axial tomography to produce complex three-dimensional models that represent the morphological and physiological characteristics of the real tissues. Biomodels are applied to numerical analysis using the Finite Element Method and provide a perspective of the mechanical behavior in the system. In this study, a numerical evaluation was performed by developing a biomodel of the humerus, radius, and ulna (the elbow joint, composed of cortical bone, trabecular bone, and cartilage). Also introduced to the biomodel were the ligaments of the capsule joint, collateral ligaments of the ulna, and collateral ligaments of the radius. The biomodel was imported into a computer program to perform a numerical analysis considering the mechanical properties of cortical and trabecular bone (including elasticity modulus, shear modulus, Poisson relation, and density). The embedding conditions were defined to restrict displacements and rotations in the proximal zone of the humerus, applying a compression load to the other end of the biomodel at the distal area of the radius and ulna. The results are the direct consequence of how boundary conditions and external agents are applied to the structure to be analyzed, and the data obtained show how the behavior of the force applied through the component produces stresses and strains as a whole, as well as for each of the components. These stresses and strains can indicate zones with structural problems and the detection areas causing pain (assisting in a better diagnosis).

Fatigue properties of Ti-6Al-4V TPMS scaffolds fabricated via laser powder bed fusion

Variabilities imposed by the laser powder bed fusion (L-PBF) and structural design processes have resulted in deficient knowledge of structure-property relationships of the bone-inspired scaffolds (i.e., meta-biomaterials). Herein, we present new findings on the fatigue performance of L-PBF Ti-6Al-4V scaffolds designed based on triply periodic minimal surfaces (TPMSs). We found that for a similar porosity and applied stress-amplitude, Schoen-IWP scaffolds exhibit significantly higher (97%) (p < 0.05) fatigue life when compared to the Primitive; however, Primitive scaffolds could more effectively mimic the compressive mechanical properties of trabecular bone. These findings help pave the path for spatial microarchitectural design of load-bearing orthopaedic implants.

Generation of Synthetic Images of Trabecular Bone Based on Micro-CT Scans

Creating synthetic images of trabecular tissue provides an alternative for researchers to validate algorithms designed to study trabecular bone. Developing synthetic images requires baseline data, such as datasets of digital biological samples or templates, often unavailable due to privacy restrictions. Even when this baseline is available, the standard procedure combines the information to generate a single template as a starting point, reducing the variability in the generated synthetic images. This work proposes a methodology for building synthetic images of trabecular bone structure, creating a 3D network that simulates it. Next, the technical characteristics of the micro-CT scanner, the biomechanical properties of trabecular bones, and the physics of the imaging process to produce a synthetic image are simulated. The proposed methodology does not require biological samples, datasets, or templates to generate synthetic images. Since each synthetic image built is unique, the methodology is enabled to generate a vast number of synthetic images, useful in the performance comparison of algorithms under different imaging conditions. The created synthetic images were assessed using microarchitecture parameters of reference, and experimental results provided evidence that the obtained values match approaches requiring initial data. The scope of this methodology covers research aspects related to using synthetic images in further biomedical research or the development of educational training tools to understand the medical image.

Effects of loading rate, age, and morphology on the material properties of human rib trabecular bone

The material and morphometric properties of trabecular bone have been studied extensively in bones bearing significant weight, such as the appendicular long bones and spine. Less attention has been devoted to the ribs, where quantification of material properties is vital to understanding thoracic injury. The objective of this study was to quantify the compressive material properties of human rib trabecular bone and assess the effects of loading rate, age, and morphology on the material properties. Material properties were quantified via uniaxial compression tests performed on trabecular bone samples at two loading rates: 0.005 s−1 and 0.5 s−1. Morphometric parameters of each sample were quantified before testing using micro-computed tomography. Rib trabecular bone material properties were lower on average compared to trabecular bone from other anatomical locations. Morphometric parameters indicated an anisotropic structure with low connectivity and a sparser density of trabeculae in the rib compared to other locations. No significant differences in material properties were observed between the tested loading rates. Material properties were only significantly correlated with age at the 0.005 s−1 loading rate, and no morphometric parameter was significantly correlated with age. Trabecular separation and thickness were most strongly correlated with the material properties, indicating the sparser trabecular matrix likely contributed to the lower material property values compared to other sites. The novel trabecular bone material properties reported in this study can be used to improve the thoracic response and injury prediction of computational models.

Studying trabecular bone samples demonstrates a power law relation between deteriorated structure and mechanical properties -a study combining 3D printing with the finite element method.

The bone volume fraction (BV/TV) significantly contributes to the mechanical properties of trabecular bone. However, when studies compare normal trabeculae against osteoporotic trabeculae (in terms of BV/TV decrease), only an "average" mechanical result has been determined because of the limitation that no two trabecular structures are the same and that each unique trabecular structure can be mechanically tested only once. The mathematic relation between individual structural deterioration and mechanical properties during aging or the osteoporosis process has yet to be further clarified. Three-dimensional (3D) printing and micro-CT-based finite element method (μFEM) can assist in overcoming this issue. In this study, we 3D printed structural-identical but BV/TV value-attenuated trabecular bones (scaled up ×20) from the distal femur of healthy and ovariectomized rats and performed compression mechanical tests. Corresponding μFEM models were also established for simulations. The tissue modulus and strength of 3D printed trabecular bones as well as the effective tissue modulus (denoted as Ez) derived from μFEM models were finally corrected by the side-artifact correction factor. The results showed that the tissue modulus corrected, strength corrected and Ez corrected exhibited a significant power law function of BV/TV in structural-identical but BV/TV value-attenuated trabecular samples. Using 3D printed bones, this study confirms the long-known relationship measured in trabecular tissue with varying volume fractions. In the future, 3D printing may help us attain better bone strength evaluations and even personal fracture risk assessments for patients who suffer from osteoporosis.

EFFECT OF TYPE-2 DIABETES ON OSTEOPOROTIC TRABECULAR BONE MECHANICAL PROPERTIES AND MICRODAMAGE ACCUMULATION

Type-2 Diabetic (T2D) patients experience up to a 3-fold increase in bone fracture risk[1]. Paradoxically, T2D-patients have a normal or increased bone mineral density when compared to non-diabetic patients. This implies that T2D has a deleterious effect on bone quality, whereby the intrinsic material properties of the bone matrix are altered. Creating clinical challenges as current diagnostic techniques are unable to accurately predict the fracture probability in T2D-patients. To date, the relationship between cyclic fatigue loading, mechanical properties and microdamage accumulation of T2D-bone tissue has not yet been examined and thus our objective is to investigate this relationship.Ethically approved femoral heads were obtained from patients, with (n=8) and without (n=8) T2D. To obtain the mechanical properties of the sample, one core underwent a monotonic compression test to 10% strain, the other core underwent a cyclic compression test at a normalized stress ratio between 0.0035mm/mm and 0.016mm/mm to a maximum strain of 3%. Microdamage was evaluated by staining the tissue with barium sulfate precipitate [2] and conducting microcomputed tomography scanning with a voxel size of 10μm.The monotonically tested T2D-group showed no statistical difference in mechanical properties to the non-T2D-group, even when normalised against BV/TV. There was also no difference in BV/TV. For the cyclic test, the T2D-group had a significantly higher initial modulus (p&lt;0.01) and final modulus (p&lt;0.05). There was no difference in microdamage accumulation.Previous population-level studies have found that T2D-patients have been shown to have an increased fracture risk when compared to non-T2D-patients. This research indicates that T2D does not impair the mechanical properties of trabecular bone from the femoral heads of T2D-patients, suggesting that other mechanisms may be responsible for the increased fracture risk seen in T2D-patients.