Porous Carrier Research Articles

Formation of the Silicon-Containing Porous Carrier Materials Using Bacterial Cells

Four types of the loading matrices based on triethoxymethylsilane and tetraethoxysilane in the 50/50 vol % ratio were prepared. The matrices were obtained either using Paracoccus yeei bacterial cells VKM B-3302 as templates or without them. The materials were annealed at 600 and 800 °C. The effect of the cells on the resulting loading matrices was analyzed using scanning electron microscopy. It was found that the addition of P.yeei allows for the formation of the more branched surface, which is likely to result in a higher specific surface area.

Fabrication and characterization of hierarchically macroporous Al2O3 ceramic supported ZnO/ZnS photocatalyst

Hierarchically macroporous Al2O3 ceramic carriers were prepared by direct-foaming combined gel-freezing method. ZnO/ZnS photocatalyst was loaded on the porous carrier through hydrothermal method. The effects of solid content, polyvinyl alcohol content, stirring speed, and sintering temperature on the pore structure, porosity, and compressive strength of the porous carrier were investigated. The pore forming mechanism was also studied. The morphology of ZnO/ZnS photocatalyst was adjusted by changing the pH value during hydrothermal process. The results show that the porous ceramic contains four different sizes of pores, spherical pore, through pore, unidirectional pore, and interstitial pore. The pore structure and strength can be regulated through optimizing process parameters. The porosity and compressive strength of porous carrier prepared with 1.2 % PVA content, 22 % solid content, 1500 r/min stirring speed and 1500 °C sintering temperature are 89.4 % and 1.45 MPa, respectively, which is suitable to be used as the photocatalyst carrier. When the pH value is 10, the size and distribution of ZnO/ZnS photocatalyst are matched with the pore structure of porous carrier. The supported ZnO/ZnS has high photocatalytic activity and good reusability.

Enhancement of oral bioavailability of celastrol by chitosan microencapsulated porous starch carriers

Celastrol demonstrates significant potential in immunomodulatory applications; however, its low oral bioavailability presents a substantial obstacle to its clinical translation. Here, we combined porous starch with chitosan to develop an efficacious microencapsulation system aimed at enhancing the oral absorption of celastrol. Microcapsule carrier for celastrol was formulated Through the utilization of chitosan-coated porous starch particle technology and Subsequent evaluations of the morphology and release kinetics of microcapsules. The impact of microencapsulation on the enhanced absorption of celastrol was assessed through Caco-2 cell uptake experiments and in vivo pharmacokinetic studies. FT-IR analysis revealed the stable presence of celastrol in an amorphous state within the microcapsules, facilitated by hydrogen-bonding interactions between celastrol and porous starch. Simulated release experiments indicated that the chitosan coating improved the stability and extended the release of celastrol. Cell experiments, as well as in vivo distribution and pharmacokinetic investigations, demonstrated that the chitosan microencapsulation strategy significantly enhanced cellular uptake and in vivo absorption of celastrol, resulting in notably higher bioavailability compared to conventional formulations. This study successfully demonstrated the remarkable efficacy of chitosan microencapsulated porous starch carriers in enhancing the oral bioavailability of celastrol, revealing novel potential applications for these two food-grade materials in delivery systems.

Slow release of NPK fertilizer using biodegradable porous carriers synthesized from agricultural waste

This study investigates the synthesis of porous biodegradable materials from rice bran and pineapple waste to determine their potential as carriers for slow-release NPK (Nitrogen, Phosphorus, Potassium) fertilizers. Through gel formation, solvent exchange, and carbonization; agro-waste gets converted into highly porous materials. A further examination of these materials demonstrates their adsorption capability and efficacy in progressive NPK fertilizer release. Experimental results show that both rice bran and pineapple waste-derived materials are effective slow-release fertilizer carriers. However, comparative investigation shows that rice bran-based material has better slow-release properties than its pineapple waste-derived counterpart. Here we also include the kinetic study of the release rate of NPK fertilizers which turned toward a Pseudo-zero order of release rate. This study emphasizes the necessity of repurposing agricultural byproducts for sustainable material synthesis, which contributes to the advancement of green chemistry and provides eco-friendly fertilizer delivery systems.

Morphology and physicochemical properties of porous sago starch carriers produced by a variety of combination pre-treatment techniques

Morphology and physicochemical properties of porous sago starch carriers produced by a variety of combination pre-treatment techniques

Mesoporous Silica Microparticle-Protein Complexes: Effects of Protein Size and Solvent Properties on Diffusion and Loading Efficiency.

Oral administration of protein-based therapeutics is highly desirable due to lower cost, enhanced patient compliance, and convenience. However, the harsh pH environment of the gastrointestinal tract poses significant challenges. Silica-based carriers have emerged as potential candidates for the delivery of protein molecules, owing to their tuneable surface area and pore volume. We explored the use of a commercial mesoporous silica carrier, SYLOID, for the delivery of octreotide and bovine serum albumin (BSA) using a solvent evaporation method in three different solvents. The loading of proteins into SYLOID was driven by diffusion, as described by the Stokes-Einstein equation. Various parameters were investigated, such as protein size, diffusion, and solubility. Additionally, 3D fluorescence confocal imaging was employed to identify fluorescence intensity and protein diffusion within the carrier. Our results indicated that the loading process was influenced by the molecular size of the protein as octreotide exhibited a higher recovery rate (71%) compared to BSA (32%). The methanol-based loading of octreotide showed uniform diffusion into the silica carrier, whereas water and ethanol loading resulted in the drug being concentrated on the surface, as shown by confocal imaging, and further confirmed by scanning electron microscopy (SEM). Pore volume assessment supported these findings, showing that octreotide loaded with methanol had a low pore volume (1.2cc/g). On the other hand, BSA loading was affected by its solubility in the three solvents, its tendency to aggregate, and its low solubility in ethanol and methanol, which resulted in dispersed particle sizes of 223 and 231μm, respectively. This reduced diffusion into the carrier, as confirmed by fluorescence intensity and diffusivity values. This study underscores the importance of protein size, solvent properties, and diffusion characteristics when using porous carriers for protein delivery. Understanding these factors allows for the development of more effective oral protein-based therapeutics by enhancing loading efficiency. This, in turn, will lead to advances in targeted drug delivery and improved patient outcomes.

Ultra-Fast Synthesis of Highly Dispersed Pt Nanoclusters Anchored on Sulfur-Doped Porous Carbon Carriers by Nanosecond Pulsed Laser for Hydrogen Evolution Reaction.

Nanosecond pulsed laser irradiation is employed for synthesis of highly active and stable Pt-based electrocatalysts by anchoring Pt nanoclusters on porous sulfur-doped carbon supports (L-Pt/SC). Strong metal-support interaction (SMSI) between Pt and S induces a local charge rearrangement and modulates the electronic structure of Pt surroundings, thus boosting the reaction kinetics and enhancing stability in long-term hydrogen evolution reaction (HER). The L-Pt/SC catalyst exhibits high activity toward HER, with an overpotential of 23 mV at current densities reaching 10 mA cm-2 and a Tafel slope of 24mV dec-1. The unit mass activity of L-Pt/SC is calculated to be -10.8 A cm-2 mgPt -1 at an applied voltage of -0.3V versus RHE. In situ Raman spectra reveals that L-Pt/SC catalyst exhibits fast hydrogen production efficiency and its electrocatalytic HER process is determined by the Tafel step. Density functional theory calculations suggest the strong bonding energy between SC and Pt induces the formation of smaller nanoclusters of L-Pt/SC during fast pulsed laser preparation, which increases the effective contact area during the HER process thereby increasing the activity per unit mass.

Polydopamine modification on dendritic porous silica surface for efficient adhesion of functional nanoparticles

The uniform and high-density immobilization of functional nanoparticles (NPs) on porous carriers is crucial to enhance various physicochemical properties and performances in diverse applications. However, there is a limited control towards the size and distribution of functional nanoparticles loaded on the carriers. In this work, the dendritic porous silica nanoparticles (DPSNs) featuring a three-dimensional center-radial porous structure were utilized as a nanocarrier, coated with a thin layer of polydopamine (PDA) to form DPSNs@PDA. The modified PDA exhibits strong adhesion and photothermal conversion properties. The pre-synthesized gold or platinum NPs (Au or Pt NPs) with tunable sizes were uniformly and densely loaded on the DPSNs@PDA, taking advantage of the strong adhesion properties of PDA. The resulting functional NPs-loaded DPSNs@PDA composites demonstrated excellent catalytic activity and recycling stability in heterogeneous catalysis, achieving over 95 % catalytic conversion efficiency of methylene blue (MB) after six cycles. Furthermore, due to the excellent photothermal effects of PDA and Au NPs, the apparent reaction rate increased by nearly threefold under 808 nm near-infrared (NIR) laser irradiation. The developed strategy of loading pre-synthesized NPs with tunable sizes by strong PDA adhesion force shows great potential for achieving efficient integration of various functional NPs, thereby facilitating the construction of advanced multifunctional materials.

Porous starch-probiotics encapsulation for 3D-printed chocolate

This study aims to utilize 3D printing technology to prepare functional chocolates with high content and viability of probiotics. Firstly, in order to protect probiotics (L. plantarum, lpl) avoiding inactive by melting chocolate syrup, we used raw starches as different amylose/amylopectin ratios (up to ∼30% amylose) for preparing novel porous carriers to encapsulate them. Then the formed pores of porous starches (HPPS1:0,3:1,1:1,1:3,0:1) were identified by SEM and BET, and their ability to encapsulate lpl were compared (with HPPS3:1 showing the best behavior) based on the survival rate and gastrointestinal simulation system. Then HPPS3:1-lpl capsule was applied in 3D printed chocolate, with optimization of adding levels for the shaping property. Probiotic cell viability, rheology, texture, and digestion simulation were also compared. The results showed that the surviving amount of probiotics (107 CFU/g) in HPPS3:1-lpl@choc (add 15% HPPS3:1-lpl to the chocolate) was much higher than that in lpl@choc (102 CFU/g, without microencapsulation protection) after in-vitro digestion test, among which HPPS3:1-lpl@choc15 had the best shaping property. This research provides a new alternative strategy for utilizing porous starch carrier to encapsulate probiotics for melting 3D printing of chocolate (or other similar food materials) as personalized design.

Sorbents based on foamed phosphate glass for collecting petroleum oil products from contaminated soils and water surfaces

Relevance. The need to clean from pollution soils and water areas contaminated with oil and chemical industry wastes. Physico-chemical methods are one of the effective ways of cleaning, provided that sorbents are applied in time to collect contaminants from the surface of water areas and landscapes. Sorption is the most efficient and cost-effective method for relatively small scale pollution. Despite the variety of existing sorbents, in most cases when cleaning up accidental spills, first of all, economic benefits and oil capacity value of the sorbent are guided. However, such essential criteria as: 1) main purpose (type of polluted surface and nature of pollution); 2) physical and chemical properties, including structural characteristics and acid-base adsorption centers; 3) peculiarities of oil or other pollutants adsorption. Taking into account these factors, it is possible to develop and improve the formulation of sorbents based on phosphate foams. Introduction of various modifying additives into material composition is likely to expand their field of application. Aim. Development of formulation and technological features of obtaining new phosphate sorbents in relation to their intended purpose: for collecting oil and petroleum product spills from soil or water surfaces. Methods. Gravimetric, microscopic spectroscopic, statistical and comparative methods. Results and conclusions. The authors have compared sorbents no. 1 and 2 in terms of physical and chemical properties, morphology and cleaning efficiency. Based on our laboratory studies, we concluded that sorbent no. 1 is better suited for sorption from aqueous surfaces and sorbent no. 2 is better suited for soil cleaning. Both sorbents have the potential to improve their technological properties. This allows refining the formulation of these materials with further testing in laboratory and field conditions, for example, at oil spill sites. For this purpose, it is possible to change the material composition using a different foaming agent, applying modifying additives and varying the temperature mode of firing. Development of new compositions and methods of sorbent foaming will make it possible to select optimal characteristics for each type of contamination. The author proposed as well to create phosphate biosorbent obtained by immobilization of fungi and bacteria on the surface of highly porous carrier. In this case, after sorption of pollution, adsorbed substances will undergo biodegradation with the formation of safe products, and the sorbent will perform the role of fertilizer.

High N2-selectivity of nitrite reduction by palladium-laden nanocomposite with self-sufficient electron donators

Selectively reducing nitrite to gaseous nitrogen (N2) with an effective and recyclable fashion stands as an attractive alternative for treating the relevant wastewater. Herein, a Pd-based nanocomposite (Pd@EDA-CMPS) was subtly assembled by encapsulating Pd(0) nanoparticles into a porous polystyrene carrier, which was aforehand functionalized with ethylenediamine (EDA) as the endogenous electron donator. Systematical macroscopic experiments confirm that the pre-grafted EDA groups can substantially stimulate the catalytic activity of the laden Pd(0) nanoparticles with high removal efficiency and N2 selectivity of Pd@EDA-CMPS toward nitrite; specifically, high N2 selectivity (86%) was achieved by Pd@EDA-CMPS with an excellent anti-interference ability against competing anion and a broad pH-range applicability (4–11), whereas no N2 production was detected for its counterparts (CMPS, EDA-CMPS, and Pd@CMPS). Spectroscopic analyses reveal that the grafted EDA groups played a decisive role in the formation of H-loaded Pd(0) nanoparticles inside the porous substrate, which joint with the unique pH-buffering ability of EDA drove the reaction to the production of nitrogen (N2) rather than ammonia (NH3). The exhausted Pd@EDA-CMPS can be promisingly regenerated by NaOH (eluting) and NaBH4 (restoring) solution without obvious loss in treatment capacity and N2 selectivity. This work provides a feasible strategy for catalytically reducing nitrite into N2 without the provision of exogenous reductor such as hydrogen.

Preparation of CS coated graded ordered porous ZrO2 implantable drug carrier

ZrO2 is bioceramic known for its excellent chemical stability and biocompatibility. Porous ZrO2, with its large surface area, has attracted considerable attention in the field of orthopedic implant drug delivery. However, the shortcomings of poor bioactivity and insufficient drug loading capacity in traditionally prepared porous ZrO2 limit its application. In this paper, graded ordered porous ZrO2 with interconnected open pores was prepared by colloid crystal templating, which exhibited large specific surface area and excellent slow-release properties. Then, it was surface-coated with chitosan (CS) possessing bioactivity and strong adsorption capacity. Factors affecting microscopic morphology, drug loading and slow-release properties of this composite were systematically investigated using ibuprofen (IBU) as a drug model. Results showed that graded ordered porous ZrO2 significantly enhanced drug loading capacity compared to normal ordered porous ZrO2, reaching 125.66 mg/g. Additionally, surface coating modification of the composite by CS significantly affected IBU loading capacity. By regulating process parameters such as CS concentration and coating time, high-efficiency loading of IBU was realized and drug loading capacity reached up to 194.17 mg/g. In vitro drug simulation experiments showed that CS coating effectively controlled the initial burst release of IBU and prolonged the effective release time; maximum cumulative release rate reached 93.7 %. This study provides a new idea for implantable drug sustained-release systems, which may better meet medical needs.

Scaling up hybrid insulation: Integration of lignocellulose and phase change materials for sustainable thermal management

This research addresses the need for eco-friendly, thermally protective packaging materials. A scalable process was developed that minimizes greenhouse gas emissions and produces hybrid materials with improved thermal insulation, energy storage, mechanical resilience, and water resistance. By using lignocellulose as a porous carrier and polyethylene glycol (PEG) as a phase change material (PCM), convective drying proved more effective for large-scale production than freeze-drying. The resulting materials are flexible, lightweight (0.03–0.04 g/cm³), and hydrophobic. They exhibit suitable thermal properties with latent heat capacities within 110–123 J/g and thermal conductivities within 0.037–0.042 W/mK. These hybrids are leak-free during phase transitions with tunable melting points, confirming their practicality. Life Cycle Assessment (LCA) shows that this method uses less energy and produces fewer carbon emissions than freeze-drying. Thus, convective drying is a promising scaling-up method for producing effective, eco-friendly temperature-responsive insulation materials for various applications requiring temperature control.

Quality by Design Optimization of Telmisartan-loaded Self-nanoemulsifying Drug Delivery Systems

Aim: This study aimed to develop a QbD-based SNEDDS for Telmisartan to enhance its biopharmaceutical performance. Background: Quality by Design (QbD) was incorporated by selecting the Critical Process Pa-rameters (CPPs) as influential variables upon the desired responses. Using Design of Experiments (DoE) software, oil, and S/CoS were tested for pre-isotropic compatibility and formulation im-provement. A heating-cooling cycle and phase separation were used to determine the formula-tions' dispersibility, self-emulsifying time, mean globule size, and stability. Objective: Using Design of Experiments (DoE) software, oil (Capmul MCM C-10) and surfactant (Labrasol)/co-surfactant (Tween-20, and PEG-600) (S/CoS) ratios were optimized for pre-isotropic compatibility and formulation improvement. Methods: Aerosil-200, Sylysia-350, 550, and 730 were used as porous carriers, and Neusilin US2 as an adsorbing agent resulted in free-flowing granules of self-nano emulsifying drug delivery systems. The SNEDDS was further formulated into tablets using a direct compression technique with enhanced disintegration properties. Results: The prepared SNEDDS tablets exhibited a 71% increase in drug dissolution as compared to the pure drug and marketed formulation after the in vitro dissolution studies. Conclusion: This QbD approach offers a promising strategy for developing SNEDDS formula-tions for poorly soluble drugs like Telmisartan.

Porous Silica Nanomaterials as Carriers of Biologically Active Natural Polyphenols: Effect of Structure and Surface Modification.

For centuries, humans have relied on natural products to prevent and treat numerous health issues. However, biologically active compounds from natural sources, such as polyphenols, face considerable challenges, due to their low solubility, rapid metabolism, and instability, which hinder their effectiveness. Advances in the nanotechnologies have provided solutions to overcoming these problems through the use of porous silica materials as polyphenol carriers. These materials possess unique properties, such as a high specific surface area, adjustable particle and pore sizes, and a surface that can be easily and selectively modified, which favor their application in delivery systems of polyphenols. In this review, we summarize and discuss findings on how the pore and particle size, structure, and surface modification of silica materials influence the preparation of efficient delivery systems for biologically active polyphenols from natural origins. The available data demonstrate how parameters such as adsorption capacity, release and antioxidant properties, bioavailability, solubility, stability, etc., of the studied delivery systems could be affected by the structural and chemical characteristics of the porous silica carriers. Results in the literature confirm that by regulating the structure and selecting the appropriate surface modifications, the health benefits of the loaded bioactive molecules can be significantly improved.

Nanoplatforms derived from iron dextran combined with ascorbic acid for enhanced photothermal-chemodynamic therapy of tumors

The current limitations of chemodynamic therapy (CDT) are mainly due to the lack of metal ions (Fe2+, Cu+, etc.), glutathione overexpression, and insufficient hydrogen peroxide level in the tumor microenvironment. Here, we constructed a safe and effective nanoplatform (abbreviate as MPCF, M: 4T1 cell membranes; P: polydopamine; C: calcium phosphate; F: iron dextran) for tumor CDT applications based on ascorbic acid and iron dextran, which is clinically used in the treatment of iron deficiency anemia. The MPCF was fabricated by encapsulating iron dextran nanoparticles within porous calcium phosphate nanoparticle carriers and surface modifying with polydopamine and 4T1 tumor cell membranes. The MPCF can efficiently accumulate at tumor sites and gradually degrade to release the encapsulated iron dextran nanoparticles in response to the acidic tumor microenvironment. Intraperitoneally injected ascorbic acid not only generated hydrogen peroxide at the tumor site, but also synergistically acted with endogenous glutathione to reduce trivalent iron ions in the iron dextran to divalent iron ions, leading to depletion of the excess glutathione at the tumor site and amplification of oxidative stress effects. In addition, polydopamine-mediated photothermal therapy (PTT) can further enhance the CDT effect. In vitro and in vivo experiments demonstrated that the combination therapy of CDT and PTT based on the MPCF exhibited effective tumor inhibition and good biosafety properties. Therefore, the nanoplatforms prepared with the clinical drug iron dextran provide a new idea for the design of nanoprobes of tumor therapy with clinical translational potential.

Efficient Neutral H2O2 Electrosynthesis from Favorable Reaction Microenvironments via Porous Carbon Carrier Engineering

AbstractThe efficient electrosynthesis of hydrogen peroxide (H2O2) via two‐electron oxygen reduction reaction (2e− ORR) in neutral media is undoubtedly a practical route, but the limited comprehension of electrocatalysts has hindered the system advancement. Herein, we present the design of model catalysts comprising mesoporous carbon spheres‐supported Pd nanoparticles for H2O2 electrosynthesis at near‐zero overpotential with approximately 95 % selectivity in a neutral electrolyte. Impressively, the optimized Pd/MCS‐8 electrocatalyst in a flow cell device achieves an exceptional H2O2 yield of 15.77 mol gcatalyst−1 h−1, generating a neutral H2O2 solution with an accumulated concentration of 6.43 wt %, a level sufficiently high for medical disinfection. Finite element simulation and experimental results suggest that mesoporous carbon carriers promote O2 enrichment and localized pH elevation, establishing a favorable microenvironment for 2e− ORR in neutral media. Density functional theory calculations reveal that the robust interaction between Pd nanoparticles and the carbon carriers optimized the adsorption of OOH* at the carbon edge, ensuring high active 2e− process. These findings offer new insights into carbon‐loaded electrocatalysts for efficient 2e− ORR in neutral media, emphasizing the role of carrier engineering in constructing favorable microenvironments and synergizing active sites.

Efficient Neutral H2O2 Electrosynthesis from Favorable Reaction Microenvironments via Porous Carbon Carrier Engineering.

The efficient electrosynthesis of hydrogen peroxide (H2O2) via two-electron oxygen reduction reaction (2e- ORR) in neutral media is undoubtedly a practical route, but the limited comprehension of electrocatalysts has hindered the system advancement. Herein, we present the design of model catalysts comprising mesoporous carbon spheres-supported Pd nanoparticles for H2O2 electrosynthesis at near-zero overpotential with approximately 95 % selectivity in a neutral electrolyte. Impressively, the optimized Pd/MCS-8 electrocatalyst in a flow cell device achieves an exceptional H2O2 yield of 15.77 mol gcatalyst -1 h-1, generating a neutral H2O2 solution with an accumulated concentration of 6.43 wt %, a level sufficiently high for medical disinfection. Finite element simulation and experimental results suggest that mesoporous carbon carriers promote O2 enrichment and localized pH elevation, establishing a favorable microenvironment for 2e- ORR in neutral media. Density functional theory calculations reveal that the robust interaction between Pd nanoparticles and the carbon carriers optimized the adsorption of OOH* at the carbon edge, ensuring high active 2e- process. These findings offer new insights into carbon-loaded electrocatalysts for efficient 2e- ORR in neutral media, emphasizing the role of carrier engineering in constructing favorable microenvironments and synergizing active sites.

Formulation, Optimization and Evaluation of Dabigartan Etexilate Encapsulated Solid Supersaturated Self-Nanoemulsifying Drug Delivery System

Objective: The present study proposed Dabigatran Etexilate loaded solid supersaturat-ed self-nanoemulsifying drug delivery system (solid S-SNEDDS) for enhancement of payload, drug solubility, dissolution rate as well as minimization of drug precipitation. Methods: The study involved formulation optimization using the Box-Behnken design. The op-timal SNEDDS consisting of Caprylic acid (32.9% w/w), Cremophor EL (50.2% w/w) and Transcutol HP (18.8% w/w) as Oil, Surfactant and Co-surfactant, respectively were formulated and evaluated for particle size, PDI, Zeta potential and saturation solubility. The SNEDDS was further incorporated with PPIs for the preparation of supersaturated SNEDDS (S-SNEDDS) to in-crease the drug payload in the formulation. S-SNEDDS was converted to solid S-SNEDDS by ad-sorption onto the porous carrier i.e., Aerosil®200. The in-vitro drug release study was also con-ducted for solid S-SNEDDS. Results: SNEDDS had size, PDI, and Zeta potential of 82 nm, 0.347, -10.50 mV, respectively. SNEDDS enhanced the saturation solubility of the drug by 93.65-fold. Among PPIs, HPMC K4M showed the most effective response for the formulation of S-SNEDDS. The S-SNEDDS had a more substantial drug payload, which further increased the solubility by 150 times of pure drugs and 16 times of SNEDDS. Solid S-SNEDDS exhibited free-flowing properties. Reconstituted sol-id S-SNEDDS had acceptable size, PDI, and Zeta potential of 131.3 nm, 0.457, and -11.3 mV, respectively. In-vitro drug release study revealed higher drug dissolution and minimized drug pre-cipitation by SNEDDS compared to marketed products and pure drugs. Conclusion: Proposed nano-formulation was found to efficiently improve the aqueous solubility of the drug and avoid the drug precipitation, thereby avoiding drug loss and improving drug bioa-vailability.

Heterogeneous Porous Synergistic Photocatalysts for Organic Transformations.

Recent interest has surged in using heterogeneous carriers to boost synergistic photocatalysis for organic transformations. Heterogeneous catalysts not only facilitate synergistic enhancement of distinct catalytic centers compared to their homogeneous counterparts, but also allow for the easy recovery and reuse of catalysts. This mini-review summarizes recent advancements in developing heterogeneous carriers, including metal-organic frameworks, covalent-organic frameworks, porous organic polymers, and others, for synergistic catalytic reactions. The advantages of porous materials in heterogeneous catalysis originate from their ability to provide a high surface area, facilitate enhanced mass transport, offer a tunable chemical structure, ensure the stability of active species, and enable easy recovery and reuse of catalysts. Both photosensitizers and catalysts can be intricately incorporated into suitable porous carriers to create heterogeneous dual photocatalysts for organic transformations. Notably, experimental evidence from reported cases has shown that the catalytic efficacy of heterogeneous catalysts often surpasses that of their homogeneous analogues. This enhanced performance is attributed to the proximity and confinement effects provided by the porous nature of the carriers. It is expected that porous carriers will provide a versatile platform for integrating diverse catalysts, thus exhibiting superior performance across a range of organic transformations and appealing prospect for industrial applications.