Polyvinyl Chloride Plastisol Research Articles

Healing Function for Abraded Fingerprint Ridges in Tactile Texture Sensors.

Tactile texture sensors are designed to evaluate the sensations felt when a human touches an object. Prior studies have demonstrated the necessity for these sensors to have compliant ridges on their surfaces that mimic human fingerprints. These features enable the simulation of contact phenomena, especially friction and vibration, between human fingertips and objects, enhancing the tactile sensation evaluation. However, the ridges on tactile sensors are susceptible to abrasion damage from repeated use. To date, the healing function of abraded ridges has not been proposed, and its effectiveness needs to be demonstrated. In this study, we investigated whether the signal detection capabilities of a sensor with abraded epidermal ridges could be restored by healing the ridges using polyvinyl chloride plastisol as the sensor material. We developed a prototype tactile sensor with an embedded strain gauge, which was used to repeatedly scan roughness specimens. After more than 1000 measurements, we observed significant deterioration in the sensor's output signal level. The ridges were then reshaped using a mold with a heating function, allowing the sensor to partially regain its original signal levels. This method shows potential for extending the operational lifespan of tactile texture sensors with compliant ridges.

Acoustic velocity and stability of tissue-mimicking echogenic materials for ultrasound training phantoms

Purpose. High-fidelity mannequins are increasingly used to train the medical staff on many medical procedures. Lately, a new challenge regarding echogenic materials to build ultrasound-responding phantoms has emerged. The challenge is to find materials with a suitable combination of ultrasound velocity and consistency to the touch. Methods. Bibliographic research was performed to identify materials with promising stiffness, shape retention, and ultrasound velocity combinations. As-standardized-as-possible specimens were realized and tested using an A-mode ultrasound machine to evaluate the US velocity through them. Four differently doped silicones, five gelatin-based materials, five synthetic gelatins, and a 3D printable resin were included in the study. After being tested, the materials were monitored for 12 days to assess their durability and shape retention and tested again to evaluate the ultrasound velocity’s stability. In the paper, the results of the characterization and follow-up of the materials are presented. Results. Outcomes show that gelatins are exceptional soft tissue-mimicking materials in terms of ultrasound velocity and consistency to the touch, but are poor in terms of overtime stability and therefore suitable for disposable short-term phantoms only. Doped silicones present lower ultrasound velocity compared to the reference value of 1540 m/s found in the literature, but excellent overtime stability, and shape retention properties. Values close to biological ones were also given by the Elastic 50A and by polyvinyl chloride plastisol. Conclusion. The paper gives a quantitative overview of the fidelity of both already-in-use and non-conventional materials, focusing on the ultrasound velocity value through them and their longevity in terms of macroscopically observed dehydration, shape retention, and bacterial onset.

Development of an anatomical breast phantom from polyvinyl chloride plastisol with lesions of various shape, elasticity and echogenicity for teaching ultrasound examination.

The WHO reported an increasing trend in the number of new cases of breast cancer, making it the most prevalent cancer in the world. This fact necessitates the availability of highly qualified ultrasonographers, which can be achieved by the widespread implementation of training phantoms. The goal of the present work is to develop and test an inexpensive, accessible, and reproducible technology for creating an anatomical breast phantom for practicing ultrasound diagnostic skills in grayscale and elastography imaging, as well as ultrasound-guided biopsy sampling. We used FDM 3D printer and PLA plastic for printing an anatomical breast mold. We made a phantom using a mixture of polyvinyl chloride plastisol, graphite powder, and metallic glitter to simulate soft tissues and lesions. Various degrees of elasticity were imparted using plastisols of stiffness ranging from 3 to 17 on the Shore scale. The lesions were shaped by hand. The materials and methods used are easily accessible and reproducible. Using the proposed technology, we have developed and tested a basic, differential, and elastographic versions of the breast phantom. The three versions of the phantom are anatomical and intended for use in medical education: the basic version is for practicing primary hand-eye coordination skills; the differential one is for practicing the differential diagnosis skills; the elastographic version helps developing the skills needed for assessing the stiffness of tissues. The proposed technology allows the creation of breast phantoms for practicing hand-eye coordination and develop the critical skills for navigation and assessment of the shape, margins, and size of the lesion, as well as performing an ultrasound-guided biopsy. It is cost-effective, reproducible, and easily implementable, and could be instrumental in generating ultrasonographers with crucial skills for accurate diagnosis of breast cancer, especially in low-resource settings.

New Approach for Extrusion Additive Manufacturing of Soft and Elastic Articles from Liquid-PVC-Based Consumable Materials.

The article deals with the experimental development of a novel additive manufacturing (AM) process using a liquid consumable based on polyvinyl chloride plastisol. A conventional additive manufacturing system designed for deposition of melt filaments was converted to deposition of liquid material. Additive manufacturing with liquid plastisol enables the production of parts with low Shore A hardness and high ductility, surpassing the performance of the conventional filament process. The novel AM process enables the production of articles with a Shore A hardness of 5 to 60, and the mechanical properties of the additively manufactured articles are similar to those produced in the mold. This was achieved by varying the parameters of the AM process as well as the composition of the plastisol composition, including those filled with an inorganic filler. The application of different material distribution patterns also has a significant effect on the mechanical properties of the samples. A potential application of the investigated AM method was proposed and practically evaluated.

3D-printed Magnetic Resonance (MR)-based gynecological phantom for image-guided brachytherapy training

PURPOSE/OBJECTIVESThere is a clinical need to develop anatomic phantoms for simulation-based learning in gynecological brachytherapy. Here, we provide a step-by-step approach to build a life-sized gynecological training phantom based on magnetic resonance imaging (MRI) of an individual patient. Our hypothesis is that this phantom can generate convincing ultrasound (US) images that are similar to patient scans. METHODSOrgans-at-risk were manually segmented using patient scans (MRI). The gynecological phantom was constructed using positive molds from 3D printing and polyvinyl chloride (PVC) plastisol. Tissue texture/acoustic properties were simulated using different plastic softener/hardener ratios and microbead densities. Nine readers (residents) were asked to evaluate 10 cases (1 ultrasound image per case) and categorize each as a “patient” or “phantom” image. To evaluate whether the phantom and patient images were equivalent, we used a multireader, multicase equivalence study design with two composite null hypotheses with proportion (pr) at H01: pr ≤ 0.35 and H02: pr ≥ 0.65. Readers were also asked to review US videos and identify the insertion of an interstitial needle into the pelvic phantom. Computed Tomography (CT) and magnetic resonance (MR) images of the phantom were acquired for a feasibility study. RESULTSReaders correctly classified “patient” and “phantom” scans at pr = 53.3% ± 6.2% (p values 0.013 for H01 and 0.054 for H02, df = 5.96). Readers reviewed US videos and identified the interstitial needle 100% of the time in transabdominal view, and 78% in transrectal view. The phantom was CT and MR safe. CONCLUSIONSWe have outlined a manufacturing process to create a life-sized, gynecological phantom that is compatible with multi-modality imaging and can be used to simulate clinical scenarios in image-guided brachytherapy procedures.

Three incisional patterns of one-stage rumen cannulation techniques on associated haematological and glycaemic changes in YanKasa-Balami cross-bred rams

Despite concerns of leaks, cannula drops, and expensive cannula costs, researches on the nutritional needs of ovine species had led to the use of bovine cannulation techniques to fistulate ovine species. Nine Yankasa-Balami crossbred rams were cannulated with locally improvised polyvinyl chloride plastisol after primary-secondary skin-muscle incisions but only primary rumen incisions; primary-secondary incisions on the skin-muscle of the left flank and the rumen; and a primary incision on the skin-muscle and the rumen, designated as groups A, B, and C, respectively. Glycaemic and haematological responses in the rams were measured at pre-anaesthesia (10 minutes), 0 h, 4 h, 8 h, 12 h, 16 h, 20 h, 24 h, 48 h, 72 h, 96 h, 120 h, 144 h, and weeks 1, 2, 3 and 4. At 10 minutes post-anaesthesia, blood glucose levels in groups A, B, and C were higher than Pre values: 108.33 ± 10.2, 118.33 ± 51.83 and 153.33 ± 46.31, respectively. Moderate dehydration was suggestive of PCV alterations due to fistula fluid loss while neutrophils, eosinophils, and monocytes were responsible for the increased leucocyte levels. As monocytes contribute to phagocytosis, neutrophils and eosinophils are indicative of surgical stress. Despite the fact that group B's blood glucose levels were much lower than group C's, the results were within the normal species range. Above all, the three incisional patterns are usable for rumen cannulation. Group B's rumen cannulation procedure was more traumatic than groups A and C's, and group A's was ranked second among the most stressful procedures.

Three incisional patterns of one-stage rumen cannulation techniques and associated haematologic and glycaemic changes in Yankasa-Balami cross-bred rams

Despite concerns of leaks, cannula drops, and expensive cannula costs, researches on the nutritional needs of ovine species had led to the use of bovine cannulation techniques to fistulate ovine species. Nine Yankasa-Balami crossbred rams were cannulated with locally improvised polyvinyl chloride plastisol after primary-secondary skin-muscle incisions but only primary rumen incisions; primary-secondary incisions on the skin-muscle of the left flank and the rumen; and a primary incision on the skin-muscle and the rumen, designated as groups A, B, and C, respectively. Glycaemic and haematological responses in the rams were measured at pre-anaesthesia (10 minutes), 0 h, 4 h, 8 h, 12 h, 16 h, 20 h, 24 h, 48 h, 72 h, 96 h, 120 h, 144 h, and weeks 1, 2, 3 and 4. At 10 minutes post-anaesthesia, blood glucose levels in groups A, B, and C were higher than Pre values: 108.33 ± 10.2, 118.33 ± 51.83 and 153.33 ± 46.31, respectively. Moderate dehydration was suggestive of PCV alterations due to fistula fluid loss while neutrophils, eosinophils, and monocytes were responsible for the increased leucocyte levels. As monocytes contribute to phagocytosis, neutrophils and eosinophils are indicative of surgical stress. Despite the fact that group B's blood glucose levels were much lower than group C's, the results were within the normal species range. Above all, the three incisional patterns are usable for rumen cannulation. Group B's rumen cannulation procedure was more traumatic than groups A and C's, and group A's was ranked second among the most stressful procedures.

Design and validation of a phantom for transcranial ultrasonography.

Commercial medical ultrasound phantoms are highly specific as they simulate particular clinical scenarios. This makes them expensive to use in multi-target research and training. General approaches to human tissue and organ modeling are described in the manufacturing methodology, access to which is restricted by the manufacturer's trade secret. Our aim is to propose a reproducible methodology to design a head phantom for transcranial ultrasound training and research from widely available materials and to validate its applicability. To create an anthropomorphic phantom, we used data from real patients obtained by CT and MRI scans. We combined FDM and LCD 3D printing to achieve the desired acoustic performance and ergonomics of the phantom. We fabricated the phantom using polyvinyl chloride plastisol, photopolymer, and PLA to simulate brain tissue, temporal acoustic windows, and acoustically opaque parts of the skull, respectively. Notably, the phantom fabrication method uses only readily available materials and is easy to reproduce. We developed a basic one and anatomical one versions of the head phantom. The basic version contains a simplified brain: tissue-mimicking material is poured into the skull with needles inserted, which specific pattern is easy to recognize in B-mode images. The anatomical version has an anatomically correct brain dummy extracted from MRI data and contains multiple randomly distributed small metal, plastic, and bony objects ranging in size from 1 to 3mm each. The proposed methodology allows producing head phantoms for transcranial ultrasound training and research. The anatomical accuracy of the model is proved by ultrasonography and CT studies. Both versions of the phantom comprise the skull and the brain and are intended for ultrasound imaging through the temporal bone acoustic window. Needles and small objects serve as navigation targets during the training procedure. The basic version helps learning basic navigation skills, while the anatomical one provides a realistic setting to perform the diagnostic procedure.

Model-based optical and acoustical compensation for photoacoustic tomography of heterogeneous mediums

Photoacoustic tomography (PAT) is a non-invasive, high-resolution imaging modality, capable of providing functional and molecular information of various pathologies, such as cancer. One limitation of PAT is the depth and wavelength dependent optical fluence, which results in reduced PA signal amplitude from deeper tissue regions. These factors can therefore introduce errors into quantitative measurements such as oxygen saturation (sO2) or the localization and concentration of various chromophores. The variation in the speed-of-sound between different tissues can also lead to distortions in object location and shape. Compensating for these effects allows PAT to be used more quantitatively. We have developed a proof-of-concept algorithm capable of compensating for the heterogeneity in speed-of-sound and depth dependent optical fluence. Speed-of-sound correction was done by using a straight ray-based algorithm for calculating the family of iso-time-of-flight contours between the transducers and every pixel in the imaging grid, while fluence compensation was done by utilizing the graphics processing unit (GPU) accelerated software MCXCL for Monte Carlo modeling of optical fluence variation. This algorithm was tested on a polyvinyl chloride plastisol (PVCP) phantom, which contained cyst mimics and blood inclusions to test the algorithm under relatively heterogeneous conditions. Our results indicate that our PAT algorithm can compensate for the speed-of-sound variation and depth dependent fluence effects within a heterogeneous phantom. The results of this study will pave the way for further development and evaluation of the proposed method in more complex in-vitro and ex-vivo phantoms, as well as compensating for the wavelength-dependent optical fluence in spectroscopic PAT.

Tunable blood oxygenation in the vascular anatomy of a semi-anthropomorphic photoacoustic breast phantom.

.Significance: Recovering accurate oxygenation estimations in the breast with quantitative photoacoustic tomography (QPAT) is not straightforward. Accurate light fluence models are required, but the unknown ground truth of the breast makes it difficult to validate them. Phantoms are often used for the validation, but most reported phantoms have a simple architecture. Fluence models developed in these simplistic objects are not accurate for application on the complex tissues of the breast.Aim: We present a sophisticated breast phantom platform for photoacoustic (PA) and ultrasound (US) imaging in general, and specifically for QPAT. The breast phantom is semi-anthropomorphic in distribution of optical and acoustic properties and contains wall-less channels with blood.Approach: 3D printing approaches are used to develop the solid 3D breast phantom from custom polyvinyl chloride plastisol formulations and additives for replicating the tissue optical and acoustic properties. A flow circuit was developed to flush the channels with bovine blood with a controlled oxygen saturation level. To showcase the phantom’s functionality, PA measurements were performed on the phantom with two oxygenation levels. Image reconstructions with and without fluence compensation from Monte Carlo simulations were analyzed for the accuracy of oxygen saturation estimations.Results: We present design aspects of the phantom, demonstrate how it is developed, and present its breast-like appearance in PA and US imaging. The oxygen saturations were estimated in two regions of interest with and without using the fluence models. The fluence compensation positively influenced the estimations in all cases and confirmed that highly accurate fluence models are required to minimize estimation errors.Conclusions: This phantom allows studies to be performed in PA in carefully controlled laboratory settings to validate approaches to recover both qualitative and quantitative features sought after in in-vivo studies. We believe that testing with phantoms of this complexity can streamline the transition of new PA technologies from the laboratory to studies in the clinic.

Investigation of PolyVinyl Chloride Plastisol Tissue-Mimicking Phantoms for MR- and Ultrasound-Elastography

Objective: Realistic tissue-mimicking phantoms are essential for the development, the investigation and the calibration of medical imaging techniques and protocols. Because it requires taking both mechanical and imaging properties into account, the development of robust, calibrated phantoms is a major challenge in elastography. Soft polyvinyl chloride gels in a liquid plasticizer (plastisol or PVCP) have been proposed as soft tissue-mimicking phantoms (TMP) for elasticity imaging. PVCP phantoms are relatively low-cost and can be easily stored over long time periods without any specific requirements. In this work, the preparation of a PVCP gel phantom for both MR and ultrasound-elastography is proposed and its acoustic, NMR and mechanical properties are studied.Materials and methods: The acoustic and magnetic resonance imaging properties of PVCP are measured for different mass ratios between ultrasound speckle particles and PVCP solution, and between resin and plasticizer. The linear mechanical properties of plastisol samples are then investigated over time using not only indentation tests, but also MR and ultrasound-elastography clinical protocols. These properties are compared to typical values reported for biological soft tissues and to the values found in the literature for PVCP gels.Results and conclusions: After a period of two weeks, the mechanical properties of the plastisol samples measured with indentation testing are stable for at least the following 4 weeks (end of follow-up period 43 days after gelation-fusion). Neither the mechanical nor the NMR properties of plastisol gels were found to be affected by the addition of cellulose as acoustic speckle. Mechanical properties of the proposed gels were successfully characterized by clinical, commercially-available MR Elastography and sonoelastography protocols. PVCP with a mass ratio of ultrasound speckle particles of 0.6%–0.8% and a mass ratio between resin and plasticizer between 50 and 70% appears as a good TMP candidate that can be used with both MR and ultrasound-based elastography methods.

Development of oral cancer tissue-mimicking phantom based on polyvinyl chloride plastisol and graphite for terahertz frequencies.

.Significance: A new concept of a biotissue phantom for terahertz (THz) biomedical applications is needed for reliable and long-term usage.Aim: We aimed to develop a new type of biotissue phantom without water content and with controllable THz optical properties by applying graphite powders into a polyvinyl chloride plastisol (PVCP) matrix and to give a numerical description to the THz optical properties of the phantoms using the Bruggeman model (BM) of the effective medium theory (EMT).Approach: The THz optical properties of graphite and the PVCP matrix were measured using THz time-domain spectroscopy, which works in the frequency range from 0.1 to 1 THz. Two phantoms with 10% and 12.5% graphite were fabricated to evaluate the feasibility of describing phantoms using the EMT. The EMT then was used to determine the concentration of graphite required to mimic the THz optical properties of human cancerous and healthy oral tissue.Results: The phantom with 16.7% of graphite has the similar THz optical properties as human cancerous oral tissue in the frequency range of 0.2 to 0.7 THz. The THz optical properties of the phantom with 21.9% of graphite are close to those of human healthy oral tissue in the bandwidth from 0.6 to 0.8 THz. Both the refractive index and absorption coefficient of the samples increase with an increase of graphite concentration. The BM of the EMT was used as the numerical model to describe the THz optical properties of the phantoms. The relative error of the BM for the refractive index estimation and the absorption coefficient is up to 4% and 8%, respectively.Conclusions: A water-free biotissue phantom that mimics the THz optical properties of human cancerous oral tissue was developed. With 21.9% of graphite, the phantom also mimics human healthy oral tissue in a narrow frequency range. The BM proved to be a suitable numerical model of the phantom.

Feasibility study of water as thinner for polyvinyl chloride plastisol

AbstractIn the traditional formula of polyvinyl chloride (PVC) gloves, the diluent of PVC plastisol is usually organic solvent, which causes serious environmental pollution during the molding process. The aim of this study was to develop a low viscosity PVC plastisol emulsion (PDE) using water as a thinner by blending PVC emulsion (PVCE) with diisononyl phthalate (DINP) emulsion. DINP emulsion (DINPE) was prepared by a compound emulsifier of polyoxyethylene octyl phenol ether‐10 and sorbitan monooleate. The effects of compound emulsifier concentration on the stability and microstructure of DINPE were investigated. The results showed that the optimal compound emulsifier concentration of DINPE was 10 wt%. In addition, the PDE obtained by blending exhibited a relatively uniform unimodal droplet size distribution. The steady state data revealed that the emulsions were shear‐thinning pseudoplastic liquid. The effect of solid content and temperature on the apparent viscosity of PDE were also evaluated. The mechanical spectra obtained suggested the presence of weak gel structure in the PDE. The mechanical test results showed that the tensile strength and elongation at break of PVC film obtained by PDE were 12.62 MPa and 310.31%, respectively. This study demonstrated that water was effective in reducing the viscosity of PVC plastisol, which would promote the application of water thinner in glove production.

An improved abdominal phantom for intrafraction image guidance validation

A dynamically compressible phantom of the human abdomen that simulates organ motion with breathing is being developed for possible testing of image-gated beam delivery in radiotherapy. The polyvinyl chloride plastisol (PVCP) phantom features a cavity that can contain a deformable normoxic polyacrylamide gel (nPAG) dosimeter that is intended for use with MRI to provide dosimetric data. The phantom has been improved by the inclusion of new components that are more realistic anatomically and exhibit CT values similar to those of the tissues they mimic. Component organs were made from 3D-printed molds developed from CT contours of a real patient and their radiodensities adjusted by varying the mass ratios of the PVCP hardener and softener during manufacture. To make the phantom more compatible with ultrasound imaging a graphite scatterer was mixed into some of the phantom components to produce a background speckle pattern. This provided contrast between the body and a moving anatomical target intended for motion tracking.Phantom insert motion magnitude and repeatibility was assessed using CT by imaging two phantom inserts, one containing fiducial markers and the other containing iodinated gelatin, at the same position after repeated cycles of deformation. The maximum motion of a phantom fiducial at the position of the phantom treatment target was found to be 12.2 mm. The phantom design resulted in dosimeter motion with a point-to-point repatability within 0.3 mm on average and contour repeatability resulting in Dice coefficients exceeding 0.98 on average.

Numerical Simulation of the Solar Spectral Properties of Filled Polyvinyl Chloride Plastisols

Notable efforts have been done to describe the propagation of a solar radiation in a heterogeneous medium containing particles. In the latter case, it is necessary to use the radiative transfer equation (RTE) that describes the propagation of radiations in participating media. Herein, the RTE was solved by using the four-flux method coupled with the T-matrix approach for the determination of effective scattering and absorption coefficients. Consequently, it was possible to understand and to predict the interaction of light with polyvinyl chloride (PVC) plastisol–based films containing fillers such as alumina, nacre, titanium dioxide, and glass beads. It was shown that the theoretical reflectance and transmittance spectra of the filled PVC plastisol film in the visible and the near-infrared regions are quite close to the experimental ones. The effect of the film thickness, the particle diameter, and the filler concentration on the reflectance and the transmittance of filled PVC plastisol film was investigated, and it was demonstrated that the filler could be well adapted for thermal protection applications.

Changes in rheological properties of polyvinyl chloride plastisols with storage time

AbstractIn this study, the changes in the rheological curves of polyvinyl chloride (PVC) plastisols with increasing storage time and the factors affecting these changes were studied. The results show that with increasing storage time, all the “viscosity–temperature” and “viscosity–time” rheological curves of PVC plastisols exhibit nonnormal distribution change trends, that is, the viscosity first decreases, and then changes from slow increasing to rapid increasing, forming a shoulder peak, reaches to the maximum value and gradually decreases. With increasing storage time, the complex viscosities of PVC plastisols increased generally in the first, the second, and the fourth stages, and the gelation process shortened in the third stage. The first and second stages of the viscosity changes reflect the “time–temperature” equivalence principle of PVC plastisol in suspension stage. However, the maximum viscosity of PVC plastisol corresponding to temperature Tηmax does not change with increasing storage time.

Semi-anthropomorphic photoacoustic breast phantom.

Imaging parameters of photoacoustic breast imaging systems such as the spatial resolution and imaging depth are often characterized with phantoms. These objects usually contain simple structures in homogeneous media such as absorbing wires or spherical objects in scattering gels. While these kinds of basic phantoms are uncluttered and useful, they do not challenge the system as much as a breast does, and can thereby overestimate the system's performance. The female breast is a complex collection of tissue types, and the acoustic and optical attenuation of these tissues limit the imaging depth, the resolution and the ability to extract quantitative information. For testing and challenging photoacoustic breast imaging systems to the full extent before moving to in vivo studies, a complex breast phantom which simulates the breast's most prevalent tissues is required. In this work we present the first three dimensional multi-layered semi-anthropomorphic photoacoustic breast phantom. The phantom aims to simulate skin, fat, fibroglandular tissue and blood vessels. The latter three are made from custom polyvinyl chloride plastisol (PVCP) formulations and are appropriately doped with additives to obtain tissue realistic acoustic and optical properties. Two tumors are embedded, which are modeled as clusters of small blood vessels. The PVCP materials are surrounded by a silicon layer mimicking the skin. The tissue mimicking materials were cast into the shapes and sizes expected in the breast using 3D-printed moulds developed from a magnetic resonance imaging segmented numerical breast model. The various structures and layers were assembled to obtain a realistic breast morphology. We demonstrate the phantom's appearance in both ultrasound imaging as photoacoustic tomography and make a comparison with a photoacoustic image of a real breast. A good correspondence is observed, which confirms the phantom's usefulness.

The Effect of Curing Temperature and Time on the Acoustic and Optical Properties of PVCP.

Polyvinyl chloride plastisol (PVCP) has been increasingly used as a phantom material for photoacoustic and ultrasound imaging. As one of the most useful polymeric materials for industrial applications, its mechanical properties and behavior are well-known. Although the acoustic and optical properties of several formulations have previously been investigated, it is still unknown how these are affected by varying the fabrication method. Here, an improved and straightforward fabrication method is presented, and the effect of curing temperature and curing time on the PVCP acoustic and optical properties, as well as their stability over time, is investigated. The speed of sound and attenuation were determined over a frequency range from 2 to 15 MHz, while the optical attenuation spectra of samples were measured over a wavelength range from 500 to 2200 nm. The results indicate that the optimum properties are achieved at curing temperatures between 160 °C and 180 °C, while the required curing time decreases with increasing temperature. The properties of the fabricated phantoms were highly repeatable, meaning that the phantoms are not sensitive to the manufacturing conditions provided that the curing temperature and time are within the range of complete gelation-fusion (samples are optically clear) and below the limit of thermal degradation (indicated by the yellowish appearance of the sample). The samples' long-term stability was assessed over 16 weeks, and no significant change was observed in the measured acoustic and optical properties.

Deformable abdominal phantom for the validation of real-time image guidance and deformable dose accumulation.

PurposeEnd‐to‐end testing with quality assurance (QA) phantoms for deformable dose accumulation and real‐time image‐guided radiotherapy (IGRT) has recently been recommended by American Association of Physicists in Medicine (AAPM) Task Groups 132 and 76. The goal of this work was to develop a deformable abdominal phantom containing a deformable three‐dimensional dosimeter that could provide robust testing of these systems.MethodsThe deformable abdominal phantom was fabricated from polyvinyl chloride plastisol and phantom motion was simulated with a programmable motion stage and plunger. A deformable normoxic polyacrylamide gel (nPAG) dosimeter was incorporated into the phantom apparatus to represent a liver tumor. Dosimeter data were acquired using magnetic resonance imaging (MRI). Static measurements were compared to planned dose distributions. Static and dynamic deformations were used to simulate inter‐ and intrafractional motion in the phantom and measurements were compared to baseline measurements.ResultsThe statically irradiated dosimeters matched the planned dose distribution with an average γ pass rates of 97.0 ± 0.5% and 97.5 ± 0.2% for 3%/5 mm and 5%/5 mm criteria, respectively. Static deformations caused measured dose distribution shifts toward the phantom plunger. During the dynamic deformation experiment, the dosimeter that utilized beam gating showed an improvement in the γ pass rate compared to the dosimeter that did not.ConclusionsA deformable abdominal phantom apparatus which incorporates a deformable nPAG dosimeter was developed to test real‐time IGRT systems and deformable dose accumulation algorithms. This apparatus was used to benchmark simple static irradiations in which it was found that measurements match well to the planned distributions. Deformable dose accumulation could be tested by directly measuring the shifts and blurring of the target dose due to interfractional organ deformation and motion. Dosimetric improvements were achieved from the motion management during intrafractional motion.

Photoacoustic oximetry imaging performance evaluation using dynamic blood flow phantoms with tunable oxygen saturation.

Multispectral photoacoustic oximetry imaging (MPOI) is an emerging hybrid modality that enables the spatial mapping of blood oxygen saturation (SO2) to depths of several centimeters. To facilitate MPOI device development and clinical translation, well-validated performance test methods and improved quantitative understanding of physical processes and best practices are needed. We developed a breast-mimicking blood flow phantom with tunable SO2 and used this phantom to evaluate a custom MPOI system. Results provide quantitative evaluation of the impact of phantom medium properties (Intralipid versus polyvinyl chloride plastisol) and device design parameters (different transducers) on SO2 measurement accuracy, especially depth-dependent performance degradation due to fluence artifacts. This approach may guide development of standardized test methods for evaluating MPOI devices.