Polysaccharide Chiral Stationary Phases Research Articles

Simultaneous Determination of Enantiomeric Purity and Organic Impurities of Dexketoprofen Using Reversed-Phase Liquid Chromatography-Enhancing Enantioselectivity through Hysteretic Behavior and Temperature-Dependent Enantiomer Elution Order Reversal on Polysaccharide Chiral Stationary Phases.

A reversed-phase high-performance liquid chromatographic (HPLC) method was developed for the simultaneous determination of the potential impurities of dexketoprofen, including the distomer R-ketoprofen. After screening the separation capability of four polysaccharide columns (Lux Amylose-1, Lux Amylose-2, Lux Cellulose-1 and Lux Cellulose-2) in polar organic and in reversed-phase modes, appropriate enantioseparation was observed only on the Lux Amylose-2 column in an acidified acetonitrile/water mixture. A detailed investigation of the mobile phase composition and temperature for enantio- and chemoselectivity showed many unexpected observations. It was observed that both the resolution and the enantiomer elution order can be fine-tuned by varying the temperature and mobile phase composition. Moreover, hysteresis of the retention times and enantioselectivity was also observed in reversed-phase mode using methanol/water mixtures on amylose-type columns. This could indicate that the three-dimensional structure of the amylose column can change by transitioning from a polar organic to a reversed-phase mode, which affects the enantioseparation process. Temperature-dependent enantiomer elution order and rare enthalpic/entropic controlled enantioseparation in the operative temperature range were also observed in reversed-phase mode. To find the best methodological conditions for the determination of dexketoprofen impurities, a full factorial optimization design was performed. Using the optimized parameters (Lux Amylose-2 column with water/acetonitrile/acetic acid 50/50/0.1 (v/v/v) at a 1 mL/min flow rate at 20 °C), baseline separations were achieved between all compounds within 15 min. Our newly developed HPLC method was validated according to the current guidelines, and its application was tested on commercially available pharmaceutical formulations. According to the authors' knowledge, this is the first study to report hysteretic behavior on polysaccharide columns in reversed-phase mode.

Chiral LC-PDA-ORD Method for The Separation of Linagliptin Enantiomers On Coated Polysaccharide Based Amylose Tris (3, 5-Dimethylphenylcarbamate) Stationary Phases

Chiral normal phase high performance liquid chromatographic (chiral-HPLC) was designed and verified for the separation of linagliptin enantiomers using coated polysaccharide chiral stationary phases. The stationary phase was amylose tris (3, 5-dimethylphenylcarbamate) (250x4.6mm, 5 µm), while the mobile phase was a mixture of 50:50:0.1% v/v. With a flow rate of 1 mL/min, orthophosphoric acid was mixed with hexane, isopropyl alcohol, and diethyl amine to achieve a pH of 5.2. The detection was seen at 225 nm. The optical rotatory dispersion (ORD) polarimeter was connected in series to the PDA outlet in order to determine the enantiomer conformation. The linagliptin retention times were found to be 5.454 and 8.772 minutes. Between 3.9 and 23.4 µg/ml, enantiomers were discovered to be linear, with a correlation coefficient of 0.9995. This method was validated in terms of linearity, LOD, LOQ, precision, accuracy, and robustness studies in accordance with ICH requirements. Novelty: The proposed analytical method for the chiral analysis of linagliptin can be used by pharmaceutical industries quality control departments.

Modelling the enantiorecognition of structurally diverse pharmaceuticals on O-substituted polysaccharide-based stationary phases

This study aims to develop models to predict the retention, separation and elution sequence of the enantiomers of structurally diverse pharmaceuticals. More specifically, Quantitative Structure Retention Relationships (QSRR) models are built that describe the relationship between molecular descriptors and retention. Eighteen structurally diverse chiral mixtures, each consisting of a pair of enantiomers, were analyzed on two polysaccharide chiral stationary phases, Chiralcel OD-RH (cellulose tris(3,5-dimethylphenylcarbamate)) and Lux amylose-2 (amylose tris(5-chloro-2-methylphenylcarbamate)), applying either a basic or an acidic mobile phase, and their retention factor and elution sequence were determined. Both achiral and, in-house defined, chiral descriptors were used as descriptive variables to build the models. Linear regression techniques, i.e. stepwise multiple linear regression (sMLR) and partial least squares (PLS) regression, were applied to model the retention or separation as a function of the descriptors. In a first step, models were built with only achiral descriptors to model the global retention of both enantiomers of a chiral molecule. Subsequently, models were built with only chiral descriptors to predict the enantioseparation and elution sequence, and finally, models were considered with both descriptor types to predict the retention, the separation and the elution sequence of the enantiomers. The global retention was predicted well by the sMLR models with only achiral descriptors. The models with only chiral descriptors were not found suitable to predict the enantioseparation and elution sequence. Finally, the models containing both chiral and achiral descriptors allowed predicting the retention well, but their ability to predict the elution sequence and separation of the enantiomers differed widely for the chromatographic systems considered.

Chiral Separation of Cannabichromene, Cannabicyclol, and Their Acidic Analogs on Polysaccharide Chiral Stationary Phases.

Until recently, chirality has not been a major focus in the study of cannabinoids, as most cannabinoids of interest, such as cannabidiol and tetrahydrocannabinol, exist as a single isomer from natural sources. However, this is changing as more cannabinoids are identified, and compounds such as cannabichromene and cannabicyclol are emerging as potential investigatory candidates for varying indications. Because these molecules are chiral, the separation and study of the individual enantiomers' biological and physiological effects should therefore be of interest. The purpose of this study was to identify analytical separation conditions and then adapt those conditions to preparative separation. This was accomplished with a column-screening approach on Daicel's immobilized polysaccharide chiral stationary phases using non-traditional mobile phases, which included dichloromethane, ethyl acetate, and methyl tert-butyl ether under high-performance liquid chromatography conditions. CHIRALPAK® IK was found to separate all four compounds well with mobile phases containing hexane-dichloromethane (with or without an acidic additive). From these methods, the separation productivities were calculated to better visualize the separation scalability, which shows that the kilogram-scale separations of each are feasible.

Enantioseparation and a comprehensive spectroscopic analysis of novel synthetic cathinones laterally substituted with a trifluoromethyl group

Recently, the number of structural modifications of synthetic cathinones has been growing making them the second largest group of new psychoactive substances in Europe. Although they are abused because of their various psychoactive effects, some compounds from this group also serve as pharmaceuticals. Since synthetic cathinones are chiral molecules with one chiral center, their biological, toxicological, and pharmacological properties may significantly differ according to their absolute configuration and enantiomeric excess. In this study, we have synthesized two substances bearing a pharmacologically interesting trifluoromethyl group and developed a chiral liquid chromatography method using a polysaccharide chiral stationary phase to separate the corresponding enantiomers of both these drugs. Subsequently, we utilized molecular spectroscopic methods including chiroptical (electronic circular dichroism and vibrational circular dichroism) and non-polarizable (infrared and ultraviolet absorption) spectroscopies. In combination with density functional theory calculations, we have obtained stable conformers of selected enantiomers in solution and their relative abundances, which we used to simulate their spectra. The experimental and calculated data have been used to elucidate the 3D structure of the enantiomerically pure compounds and assign the absolute configuration of all prepared compounds.

Chiral separation and characterization of methoxphenidine – A popular street drug

Methoxphenidine (MXP) belongs among dissociative anesthetics from the group of new psychoactive substances. According to the unofficial user experiences, MXP is less active than common dissociative anesthetics like ketamine, yet, several intoxications were associated with this substance up to this date. Within our previous work, we discovered that at least some MXP samples on the drug market may contain zincate complex which we believe may be responsible for the unusual properties of the purported HCl salts. MXP comprise a stereogenic center in its molecular structure, which is disregarded by the manufacturers and, therefore, MXP is available on the drug scene as a racemic mixture only. However, the differences between the effects and activity of the enantiomers remain to be discovered. Hereby we present a chiral resolution by crystallization, which we used to obtain both the enantiomers of MXP. To control their optical purity, we have developed a new supercritical fluid chromatography (SFC) method. Finally, a combination of electron circular dichroism (ECD) and vibrational circular dichroism (VCD) spectra supported by density functional theory (DFT) calculation has been used to assign the absolute configuration of both enantiomers. Racemic Methoxphenidine hydrochloride was prepared in-house. Then individual enantiomers were obtained by process of crystallization using chiral (−) or (+)-2,3-dibenzoyl-tartaric acid monohydrate. An Acquity UltraPerformance Convergence ChromatographyTM (UPC2) from Waters (Milford, MA, USA) was used for HPLC and SFC enantioseparation. For control of the purity of the obtained enantiomers after crystallization, a HPLC method has been used. To improve efficiency of the existing chiral HPLC method, an SFC enantioseparation method was develop. Four polysaccharide-based CSPs (Alcyon SFC CSP Amylose-SA, Cellulose-SB and Cellulose-SC and CHIRALPAK® IE-3) and CO2-containing mobile phases were employed. The ECD and UV absorption spectra were obtained on a Jasco J-815 spectrometer (Jasco, Japan) in a quartz cuvette (Hellma, Germany) with an optical pathlength of 1 mm. The VCD and IR absorption spectra were measured on Fourier transform infrared spectrometer IFS 66/S equipped with a PMA 37 VCD/IRRAS module (both Bruker, Germany), BaF2 polarizer, and MCT detector (InfraRed Associates, USA). Measurements were carried out in a BioCell cuvette with CaF2 windows (Biotools, Inc, USA) and an optical pathlength of 27.3 μm. DFT simulations were performed to find the stable structures of MXP in solution and to determine the absolute configuration of enantiomers. It was important to develop a fast and robust method, which would enable high-throughput screening of samples, e.g. in toxicology laboratories. Therefore, one of the goals of this study was to develop a novel SFC enantioseparation method for the chiral resolution of MXP enantiomers using a polysaccharide chiral stationary phase. In comparison, the SFC assay provides significant decreasing of retention time with satisfactory resolution. Repeatability of the method was proven by an intra- and an interday validation with respect to retention time and resolution factor. Using DFT calculation, we found two stable conformers in solution, calculated their relative abundances based on Boltzmann distribution and simulated their Boltzmann-weighted spectra. Their comparison with experimental spectra allowed us to determine the absolute configuration of enantiomers. We present an enantioseparation method for methoxphenidine using SFC and offer a comparison of four commercial chiral stationary phases. Using this method, we show that crystallization with a chiral acid provides pure enantiomers of MXP, which was confirmed by chiroptic methods supported with DFT calculations.

Enantioseparation and antioxidant activity of novel diarylpyrazoline derivatives

Three chiral pyrazoline derivatives were synthesized by a flavanone ring-opening reaction followed by cyclocondensation with hydrazine hydrate to give better yields. Their enantiomeric resolution was achieved using polysaccharide chiral stationary phase columns consisting of cellulose (Chiralcel®OD-RH, Chiralcel®OZ-3) and amylose (Chiralpak®IA) by high-performance liquid chromatography. The separation was affected by the nature and concentration of the alcohol modifiers in the mobile phase. Taking 5-methoxy-2-(3-phenyl-4,5-dihydro-1H-pyrazol-5-yl)phenol (3a) as an example, the best separation was obtained by using the Chiralpak®IA column, with a separation factor α = 1.24 and Rs = 5.66 within an analysis time of <30 min. The diarylpyrazolines showed good antioxidant activity, studied by the DPPH method.

Quality by design approach for enantioseparation of terbutaline and its sulfate conjugate metabolite for bioanalytical application using supercritical fluid chromatography

Terbutaline is mainly metabolized by sulfoconjugation stereoselectively, favoring its (S)-(+) enantiomer. Reported chiral separations of Terbutaline enantiomers were achieved by various chromatographic methods. However, the simultaneous enantioseparation of Terbutaline and the monosulfate conjugate metabolites was never reported. This study aims at shedding light on the influential factors and interactions leading to successful enantioseparation of Terbutaline and its monosulfate conjugate pairs by Supercritical Fluid Chromatography (SFC) for the first time within a Quality by Design framework using Design of Experiments. The effect of molarity of mobile phase additive, mobile phase flow rate, column temperature and back pressure were evaluated. Compared to previous reports, the response surface interestingly revealed the favorability of high temperature and high flow rate up to 2.25 ml/min for resolution of the two pairs of enantiomers on polysaccharide chiral stationary phase CHIRALPAK IC. In addition, a switch in the elution order of Terbutaline and the sulfate conjugate peak pairs was observed upon elimination of the mobile phase additive where the sulfate conjugate underwent intra-molecular ionic interactions and the change in elution order was only due to TER behavior. The multifactorial interactions would not have been detected with the common one-factor-at-a-time approach during method development, demonstrating the superiority and importance of the Analytical Quality by Design frame in enantioseparation.

The separation of several organophosphate pesticides on immobilized polysaccharide chiral stationary phases.

While not initially a focus or priority, in recent decades, an emphasis has been placed on the activity of individual enantiomers of widely used pesticides. Of particular note are organophosphorus‐based pesticides like fenamiphos and profenofos, as examples. This work explores the enantioselective high‐performance liquid chromatography (HPLC) separations of seven such organophosphorus pesticides (OP's) on the library of immobilized polysaccharide‐based chiral stationary phases (CSPs) with normal phase hexane/alcohol mixtures. Further exploration of the effect of mobile phase strength and temperature on several of the separations was performed using simple factorial design. Equivalent retention of the first eluting enantiomer of several combinations of temperature and mobile phase was compared for peak shape, selectivity, and resolution. Similarly, equivalent selectivity of several combinations of temperature and mobile phase was compared for peak shape, retention of the first eluting enantiomer, and resolution. The results of this study make available several new chiral separations of the OPs included in the work that were not previously documented, including separations on the three most recently commercialized phases, Chiralpak IH, IJ, and IK. Additionally, sufficient understanding was obtained to be able to predict the trade‐off of resolution, analysis time, peak sharpness (and thus improve limit‐of‐detection [LOD]/limit‐of‐quantification [LOQ]), robustness, and convenience of conditions for further application optimization.

Comprehensive two-dimensional liquid chromatographic method (Chiral × Achiral) for the simultaneous resolution of pesticides

This work demonstrates the potential of two-dimensional liquid chromatography (2D-LC) to increase the resolution capacity of multiple pesticides in a single analysis of samples that contain both chiral and achiral compounds. The setup is based on the combination of a chiral column in the first dimension and an achiral column in the second dimension using the on-line full comprehensive mode (LC × LC). This method was optimized for the separation of 24 pesticides (17 chiral and 7 achiral). The 2D-LC system was built with an active flow splitter pump in order to easily adjust the volume of sample transferred to the second dimension and to select and optimize independently the flow rate in the first dimension. The first-dimension optimization involved the comparison of enantioresolution abilities of three different polysaccharides chiral stationary phases as well as different elution conditions, while in the second-dimension parameters like stationary phase and organic modifier were explored. Other experimental variables that influence the two-dimensional peak capacity (orthogonality, sampling frequency, shift gradients, etc.) are discussed.

Development and Validation of Teneligliptin Stereoisomers by HPLC Using Cellulose Based Immobilized Polysaccharide Chiral Stationary Phase

Background: There is no single chiral method for the quantitation of teneligliptin stereoisomers by high performance liquid chromatography (HPLC). Hence, there is a need for the quantification of teneligliptin (TNGP) and its stereoisomers. Objective: The main aim of the research work is to develop a novel simple, selective, precise and accurate HPLC method for the separation of TNGP and its stereoisomers. Methods: Different screening trials were executed by changing the mobile phase compositions to normal phase and polar mode and also by utilizing the different immobilized polysaccharide chiral columns like CHIRALPAK IA, IC, ID, IE, IF and IG. All the stereoisomers were eluted with high resolution, on CHIRALPAK IC-3 (4.6×250 mm), 3 μm chiral stationary phase (CSP) with a flow rate of 0.7 mL/min. The chromatographic system was processed with isocratic mode comprising ethanol: acetonitrile: ethanolamine in the proportion of 90:10:0.1% v/v/v with a column oven temperature of 15°C and detection wavelength of 250 nm. Results: The limit of detection (LOD) and limit of quantification (LOQ) values of TNGP(API), R,S-isomer, S,R-isomer and R,R-isomer were found to be 0.036/0.11, 0.029/0.09, 0.038/0.011 and 0.020/0.06 μg/mL, respectively. The method was found to be precise, accurate and linear (R2 &gt; 0.999). Conclusion: The developed method was successfully applied for the quantification of bulk drug without any interference with the extraneous components. Hence, the method can be utilized successfully in the pharmaceutical organizations for the separation and quantification of TNGP isomers.

The Separation of Cannabinoids on Sub-2 µm Immobilized Polysaccharide Chiral Stationary Phases.

The increased use and applicability of Cannabis and Cannabis-derived products has skyrocketed over the last 5 years. With more and more governing bodies moving toward medical and recreational legalization, the need for robust and reliable analytical testing methods is also growing. While many stationary phases and methods have been developed for this sort of analysis, chiral stationary phases (CSPs) are unique in this area; not only can they serve their traditional chiral separation role, but they can also be used to perform achiral separations. Given that mixtures of cannabinoids routinely contain enantiomers, diastereomers, and structural isomers, this offers an advantage over the strictly achiral-only analyses. This work presents the separation of a 10-cannabinoid mixture on several polysaccharide-based sub-2 µm CSPs with both normal-phase and reversed-phase ultra-high-performance liquid chromatography (UHPLC) conditions. Along with the separation of the mixture, appropriate single-peak identification was performed to determine the elution order and reported where applicable.

Enantioselective analyses of chloroquine and hydroxychloroquine in rat liver microsomes through chiral liquid chromatography-tandem mass spectrometry.

An efficient, sensitive and selective liquid chromatography-tandem mass spectrometry (LC-MS/MS) chiral analysis method was established for determination of chloroquine and hydroxychloroquine enantiomers in rat liver microsomes. Effects of polysaccharide chiral stationary phases and basic additives on chiral separations of two analytes were discussed in detail. Amylose tris(3, 5-dimethylphenylcarbamate)-coated chiral stationary phase showed the best separation performance for them with acetonitrile-diethylamine-ethanol-diethylamine mixture (90:0.1:10:0.1, v/v/v/v) among four chiral stationary phases. Then, multiple reaction monitoring mode was selected as the data acquisition for determination of two pairs of enantiomers. The proposed LC-MS/MS chiral analysis method was validated in terms of linearity, accuracy, precision, and specificity. Good linearity with correlation coefficient over 0.998 was obtained in the concentration range of 0.05-5 μM. Limits of quantification for chloroquine and hydroxychloroquine enantiomers were 5.0 and 1.0 nM, respectively. The recoveries ranged from 81.14% to 111.09%. The intra-day and inter-day relative standard deviation were less than 6.5%. Moreover, concentrations of chloroquine and hydroxychloroquine enantiomers in rat liver microsomes were determined through the proposed LC-MS/MS analysis method. After incubated with rat liver microsomes for 10 min, the enantiomeric factor of hydroxychloroquine decreased from 0.50 to 0.45 (p < 0.001). In brief, our developed determination method for chloroquine and hydroxychloroquine enantiomers through LC-MS/MS spectrometry showed the characteristics of high-efficiency, fast speed, and very low detection limit, and would be greatly beneficial for screening and quantitation of them in biological matrices.

Enantiomeric Separation of Indole-3-Propanamide Derivatives by Using Supercritical Fluid Chromatography on a Polysaccharide-Based Chiral Stationary Phase

Thirteen pairs of I3P enantiomers were screened using nine polysaccharide chiral stationary phases and three different mobile phases. The purification strategy for 13 pairs of I3P enantiomers were designed and optimized considering enantiomeric purity and enrichment of isomers. Out of 13 I3P derivatives which were screened using supercritical fluid chromatography, 10 derivatives displayed excellent baseline separation using a Lux Cellulose-4 column and their resolution from higher to lower order of I3P-11, 13, 4, 12, 2, 1, 9, 3, 7 and 8 derivatives whereas in case of Lux Cellulose-2 column, the moderate separation was achieved as compared to Cellulose-4 in the order I3P-5, 6 and 10 derivatives. Excellent enantiomeric separations and retentions for all 13 I3P enantiomer derivatives were obtained in Cellulose-4 and Cellulose-2 columns in presences of methanol as organic modifier without any additives except in the case of I3P 12 enantiomer. The absolute stereochemical assignment of the purified isomers was determined through an optical rotation study. Among the series of I3P derivatives, I3P-5 showed potent antioxidant activity against catalase with an IC50 value of 13.78μM. Further molecular docking, MM/GBSA and molecular dynamics studies revealed that the I3P-5 derivatives effectively bind to catalase with a docking score of -5.41kcal/mol. Which validated chiral docking and indicated great potential for enantiomeric separation in drug discovery and present studies (R)-enantiomer preferentially depicts good binding capacity with catalase.

Enantioseparation of cloprostenol on the polysaccharide chiral stationary phase: Influence of the mobile phase on enantioselective adsorption

Cloprostenol (CLO) is an important chiral drug widely used in veterinary practice. In high-performance liquid chromatography (HPLC), the acetonitrile/water system is more effective in the chiral resolution of CLO. The change in the ratio of acetonitrile and water has a great influence on the chiral selectivity of CLO. The enantioselective adsorption and nonselective adsorption of CLO on the polysaccharide stationary phase with three groups of mobile phases (Acetonitrile / 0.1 TFA; 95 Acetonitrile/5 H2O/0.1 TFA; 45 Acetonitrile/55 H2O/0.1 TFA) were determined and fitted with the subtraction fitting method (SFM). Adding a small amount of water to the mobile phase mainly reduced the enantioselective equilibrium adsorption constants Ks of (-)-CLO and thus changed the selectivity. Among them, the true separation factor (αtrue) of the 95 Acetonitrile/5 H2O mobile phase was as high as 92.86. Chiral preparation was performed on the basis of this mobile phase. The preparation performance in kkd (kilograms per kilogram of stationary phase purified compound per day) was 0.25 kg racemate/kg CSP/day.

Direct enantioselective gradient reversed-phase ultra-high performance liquid chromatography tandem mass spectrometry method for 3-hydroxy alkanoic acids in lipopeptides on an immobilized 1.6μm amylose-based chiral stationary phase.

3-Hydroxy fatty acids are important chiral building blocks of lipopeptides and metabolic intermediates of fatty acid oxidation, respectively. The analysis of the stereochemistry of such biomolecules has significant practical impact to elucidate and assign the enzymatic specificity of the biosynthesis machinery. In this work, a new mass spectrometry compatible direct chiral ultra high performance liquid chromatography separation method for 3-hydroxy fatty acids without derivatization is presented. The application of amylose tris(3,5-dimethylphenyl carbamate) based polysaccharide chiral stationary phase immobilized on 1.6μm silica particles (CHIRALPAK IA-U) allows the enantioseparation of 3-hydroxy fatty acids under generic electrospray ionization mass spectrometry friendly reversed phase gradient elution conditions. Adequate separation factors were achieved with both acetonitrile and methanol as organic modifiers, covering hydrocarbon chain lengths between C6 and C14 . Elution orders were derived from rhamnolipid (R-95) of which enantiomerically pure or enriched (R)-3-hydroxy fatty acids were recovered after ester hydrolysis. The S-configured acids consistently eluted before the respective R-enantiomers. The method was successfully applied for the elucidation of the absolute configuration of 3-hydroxy fatty acids originating from a novel lipopeptide with unknown structure. The work furthermore demonstrates that gradient elution is a viable option also in enantioselective (ultra)high performance liquid chromatography, even for analytes with modest separation factors, although less commonly exploited.

Enantioselective separation of zopiclone on immobilized polysaccharide chiral stationary phase by HPLC: Method development and validation

New, sensitive and rapid chiral HPLC method for enantioseparation and determination of widely used hypnotic drug, zopiclone, was developed. Enantioseparation was achieved on the immobilized amylose based Lux i-Amylose 1 column in polar organic mode in less than 7 min. The effects of the mobile phase composition, type and content of major components as well as acid/base ratio and column temperature on the retention and enantioseparation were investigated. The mobile phase consisted of acetonitril and methanol with small addition of triethylamine and acetic acid with a flow rate of 1 mL min-1. Calibration curves of both zopiclone enantiomers were linear over the concentration range of 5-125 μg mL-1. The limits of detection and quantification for (R)-zopiclone were 5 and 15 ng mL-1 and for (S)-zopiclone were 7 and 21 ng mL-1, respectively. It was demonstrated that the proposed method was selective, precise and robust. Finally, the validated method was applied to the determination of zopiclone enantiomers in the commercial tablets.

Separation of twelve posaconazole related stereoisomers by multiple heart-cutting chiral–chiral two-dimensional liquid chromatography

Posaconazole represents a triazole antifungal agent which is used to treat various fungal infections. It contains four chiral centers leading to 16 stereoisomers. With the convergent synthesis route, only 11 related stereoisomeric impurities may potentially exist in the active pharmaceutical ingredient (API). It is a challenge to separate all the stereoisomers in one run. To address this problem, a multiple heart-cutting chiral–chiral two-dimensional liquid chromatography (2D-LC) method was developed. The multiple heart-cutting 2D-LC separation was implemented on 2D-LC system with three chiral columns with immobilized polysaccharide chiral stationary phases, namely Chiralpak IB, IC and IF3. In the system, the column Chiralpak IB was used as the 1D separation column and IC and IF3 columns were used parallelly for the 2D separation. The twelve stereoisomers were all well separated in one run by the multiple heart-cutting chiral–chiral 2D-LC system.

Chromatographic Enantiomer Separation of Chiral Amines as Fluorene-2-carboxaldimine Derivatives Using Polysaccharide-derived Chiral Stationary Phases

Chromatographic Enantiomer Separation of Chiral Amines as Fluorene-2-carboxaldimine Derivatives Using Polysaccharide-derived Chiral Stationary Phases

Molecular dynamics simulations of the chiral recognition mechanism for a polysaccharide chiral stationary phase in enantiomeric chromatographic separations

We use explicit-solvent fully atomistic molecular dynamics (MD) simulations, permitting all the interactions between the atoms constituting the polymeric chiral stationary phase (CSP), the solvent molecules and the drug molecule enantiomers, to better understand the chiral recognition mechanism that makes chromatographic separation possible. Using amylose tris(3,5-dimethylphenyl carbamate) (ADMPC) as prototype, three solvent systems, and ten racemates as solutes, we seek a molecular dynamics average quantity that could serve as a metric that predicts which of the two enantiomers will elute first and also correlates with the ratio of retention times for enantiomers. To better understand the molecular dynamic chiral recognition that provides the discrimination which results in the separation of enantiomers by high performance liquid chromatography, we examine the differences in hydrogen bonding lifetimes in various donor–acceptor pairs between the drugs and the ADMPC, and map out the differences in ring-ring interactions between the drugs and the ADMPC. Several MD average quantities related to hydrogen-bonding lifetimes correlate with the ratio of retention times for the enantiomers. One of these quantities provides a prediction of the correct elution order 90% of the time, and the ratios of these quantities for the enantiomers provide linear correlation (0.85 coefficient) with experimental separation factors.