Polymethylmethacrylate Discs Research Articles

Melt-front instabilities during the combustion of a spinning polymer disk

Melt-front instabilities during the combustion of a spinning polymethylmethacrylate disk in air are investigated. Mainly straight rivulet-type flow patterns were found, though under certain conditions saw-tooth patterns were observed. The measured wavelengths of the instabilities agree with earlier theoretical predictions of driven contact-line instabilities.

Comparative Analysis of Plaque Removal and Wear between Electric-Mechanical and Bioelectric Toothbrushes.

Effective oral care is important for maintaining a high quality of life. Therefore, plaque control can prevent the development and recurrence of periodontitis. Brushing with a toothbrush and toothpaste is a common way to remove plaque; however, excessive brushing or brushing with abrasive toothpaste can cause wear and tear on the dental crown. Hence, we aimed to quantitatively compare the plaque-removal efficiency and tooth wear of toothbrushes using the bioelectric effect (BE) with those of electric-mechanical toothbrushes. To generate the BE signal, an electronic circuit was developed and embedded in a toothbrush. Further, typodonts were coated with cultured artificial plaques and placed in a brushing simulator. A toothpaste slurry was applied, and the typodonts were eluted with tap water after brushing. The plaques of the typodonts were captured, and the images were quantified. For the tooth wear experiment, polymethyl methacrylate disk resin blocks were brushed twice a day, and the thickness of the samples was measured. Subsequently, statistical differences between the experimental toothbrushes and typical toothbrushes were analyzed. The BE toothbrush had a higher plaque-removal efficiency and could minimize tooth wear. This study suggests that the application of BE may be a new solution for oral care.

Effect of various staining beverages on the color stability of CAD/CAM PMMA denture teeth: An in vitro study.

This study aimed to compare the color change of computer-aided design (CAD)/computer-aidedmanufacturing (CAM)polymethyl methacrylate (PMMA)denture teeth and conventional acrylic teeth after immersion in three staining beverages (coffee, red tea, and cola) for a day, 7 days, and 30 days. Group 1: Conventional acrylic teeth (n = 32). Group 2: Milled CAD/CAMteeth out of PMMA disc (n = 32). The specimens of each material were further divided into four subgroups: (1) Control group, distilled water (n = 16). (2) Red tea solution (n = 16). (3) Coffee solution (n = 16). (4) Cola (n = 16). The color change ( ) was assessed using a spectrophotometer at four time points: at the baseline (t0 ), on the 1st day (t1 ), on the 7th day (t2 ), and the 30th day (t3 ) of immersion. Kolmogorov-Smirnov test was applied, followed by performing independent samples t test, one-way analysis of variance and post-hoc Tukey tests to compare the color change values at different time points. The mean score of NBS values of the coffee solution indicates perceivable color change at the end of the 30th day in the conventional acrylic teeth group. It was 0.843 ± 0.395 at t1 , then increased to 1.017 ± 0.477 at t2 and to 2.259 ± 1.059 at t3 . There is a statistically significant difference (p < 0.05) in color change values between both tooth types at the end of the 30th day of immersion in red tea solution and a statistically significant difference at the end of the 7th day (p < 0.05) and the 30th day (p < 0.05) of immersion in coffee solution. CAD/CAMPMMA teeth are more color stable than conventional acrylic teeth after 30 days of immersion in coffee and red tea solution.

Application of single anterior teeth defect with computer-aided design and computer-aided manufacturing polymethyl methacrylate single-retainer resin-bonded fixed dental prosthesis in children

Objective: To explore the clinical effect of computer-aided design and computer-aided manufacturing (CAD/CAM) polymethyl methacrylate (PMMA) single-retainer resin-bonded fixed dental prosthesis (RBFDP) for single anterior teeth defect. Methods: A total of 14 children between 10-14 years old (male 8, female 6) who visited the Department of Pediatric Dentistry, School of Stomatology, The Fourth Military Medical University from March to December 2022 with single anterior teeth loss were enrolled in this study. The intraoral scanner was used to obtain their digital impressions, and then the data were imported into CAD software. The single-retainer RBFDP was designed by the CAD software and was manufactured by milling equipment using CAD/CAM PMMA disk. The prosthesis was then tried-in and bonded to the abutment teeth with resin cement and evaluated in a 12 month follow-up observation. The marginal discoloration, marginal adaptation, color match, secondary caries, the occurrence of fractures and loose of abutment tooth were examined on the basis of the modified United States Public Health Services evaluation system. The evaluation was divided into three scores, in which score A indicated ideal restoration effect, score B means that the restoration effect was acceptable (evaluation of restoration integrity, loose of abutment teeth and secondary caries excluded), and score C indicates that the restoration effect is not good. Results: All the 14 CAD/CAM PMMA single-retainer RBFDP had good marginal adaptation and color match with no marginal discoloration, no secondary caries, no fracture of restorations and no abnormal loose of the abutment teeth. All of the six criteria achieved score A evaluation after a three month follow-up observation. One restoration was classified as score B for fracture after a six month follow-up observation, while two restoration were classified as score B for marginal discoloration after 12 month follow-up observation. Conclusions: The CAD/CAM PMMA single-retainer RBFDP was clinically effective in restoration of single anterior teeth defect in children.

Investigating the biocompatibility, flexural strength, and surface roughness of denture base resin containing copper oxide nanoparticles: An in vitro study

AimThis study aimed to evaluate the biocompatibility, flexural strength, and surface roughness of polymethyl methacrylate (PMMA) containing Copper Oxide Nanoparticles (CuO NPs) at different concentrations. Methods25 heat-polymerized PMMA wax patterns fabricated in 5 groups containing 0.5, 5, 50, and 500 μg/ml CuO NPs and nanoparticle (NP)-free PMMA discs were prepared. 5 growth mediums (DMEM with 10% FBS and 1% penicillin-streptomycin) without disks were also incubated similarly to serve as the control groups. The cytotoxicity of the discs was measured by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-2H-tetrazolium bromide (MTT) assay on cultured Human Gingival Fibroblasts. The number of 1.3 × 104 cells were seeded in each well of 96-well plates (5 wells for the extract of each specimen). Days 1, 3, 5, and 7 were the intervals that the culture media were in direct contact with the PMMA discs for either 24 or 72 h. After that, a total of 40 specimens with 65 × 10 × 2.5 mm dimensions were prepared in five groups (n = 8). The specimens were subjected to a rugosimeter for the evaluation of surface roughness. The flexural strength test was performed using a universal testing machine. Microscopic evaluation was performed for the dispersion of the NPs. Non-parametric Kruskal-Wallis test and parametric one-way ANOVA test were used for data analysis. ResultsThe samples containing 500 μg/ml NPs showed the lowest percentage of cell viability at all incubation periods, while the highest cell viability was observed in NP-free PMMA 24 h after the seventh day of incubation. NPs at 50 and 500 μg/ml concentrations showed strongly significant differences in cytotoxicity compared to the 0 concentration and the control group (p < 0.001). Although all the samples demonstrated an increasing pattern of cell viability on the third, fifth, and seventh days, the percentage of cell viability was significantly lower after 72 h than after 24 h in all incubation periods (p < 0.001). NPs significantly increased flexural strength (p = 0.005) but did not affect the surface roughness of the PMMA discs (p = 0.396). SignificanceThe CuO NPs were cytotoxic only when applied in high concentrations, but presented a descending trend over time. No cytotoxic effect was observed in the experimental groups after seven days of incubation. Furthermore, CuO NPs increased flexural strength, but the surface roughness of the PMMA discs was not affected.

Three-piece digital complete denture obturator with a heptagonal key assembly for a patient with a total maxillectomy: A dental technique

Digital workflows have been used in the oral rehabilitation of patients with maxillofacial defects. However, dental techniques for fabricating a denture obturator for patients with a total maxillectomy are lacking. This technical report describes the use of digital technology to produce a milled complete denture obturator using an intraoral scanner, a computer-aided design software program, and computer-aided manufacturing. The limited size of the milled polymethylmethacrylate disk was resolved by separating the prosthesis into 3 pieces: the obturator base, denture base, and artificial teeth.

Evaluation of the machinability and machining accuracy of polymer-based CAD/CAM blocks using merlon fracture test model.

The aims of this study were to estimate the machinability and machining accuracy of polymer-based CAM blocks using the merlon fracture test model specified in ISO 18675: 2022. Three hybrid disc blanks (MazicDuro, HC Disk, and Enamic) and three polymethyl methacrylate (PMMA) disc blanks (PMMA Disk, PMMA Block, and MazicTemp Hybrid) were tested in this study. The machinability was evaluated by assigning scores according to the fracture range of merlons with areas divided by ten vertical planes. The machining accuracy was evaluated by superimposing methods via CAD reference data and CAD specimen data. Within the limits of this study, a thickness of 0.3 mm is recommended for the clinical application of polymer-based CAD/CAM blocks in dental restorations that require superior machinability and accuracy. In addition, the machinability and machining accuracy tests of polymer-based CAM blocks are expected to provide guidelines for preparing accurate dental restorations.

The Effect of Controlled Diabetic and Non-diabetic Saliva on Candida albicans Adherence to Heat Polymerized Acrylic Resin Discs

Background: Oral candidiasis is one of the most common infections in diabetic patients that may occur due to a decrease in salivary flow rate, alterations in the salivary composition, or both. This study aimed to investigate the effect of diabetic and non-diabetic saliva on Candida albicans adherence to the acrylic resin disc specimens, regardless of saliva volume. Methods: In this case-control study, the population consisted of 26 subjects in 2 groups (13 diabetic patients and 13 non-diabetic patients). In both groups, unstimulated whole saliva was collected. It was investigated for pH, salivary flow rate, and adhesion of C. albicans to polymethylmethacrylate disc. After preparing the polymethylmethacrylate discs, the samples were stored in diabetic saliva, non-diabetic saliva, and distilled water (negative control group) for 60 minutes at 37ºC. Then they were immersed in the yeast suspensions containing C. albicans and stained with gram stain. Yeast cells were counted using a light microscope. Results: The pH of unstimulated whole saliva in diabetic patients was significantly lower than in the control group. There was no significant difference between the flow rates of saliva in the two groups. Findings indicated that the adhesion of C. albicans to resin in diabetic saliva was higher than in non-diabetic saliva. Conclusion: This study showed the same amount of salivary flow rate in diabetic and non-diabetic individuals, lower pH, and higher Candida adherence to heat polymerization acrylic resin in the diabetic group.

Graphene-Doped Polymethyl Methacrylate (PMMA) as a New Restorative Material in Implant-Prosthetics: In Vitro Analysis of Resistance to Mechanical Fatigue

Provisional prostheses in restorations over several implants with immediate loading in completely edentulous patients increase the risk of frequent structural fractures. An analysis was performed of the resistance to fracture of prosthetic structures with cantilevers using graphene-doped polymethyl methacrylate (PMMA) resins and CAD-CAM technology. A master model was produced with four implants measuring 4 mm in diameter and spaced 3 mm apart, over which 44 specimens representing three-unit fixed partial prostheses with a cantilever measuring 11 mm were placed. These structures were cemented over titanium abutments using dual cure resin cement. Twenty-two of the 44 units were manufactured from machined PMMA discs, and 22 were manufactured from PMMA doped with graphene oxide nanoparticles (PMMA-G). All of the samples were tested in a chewing simulator with a load of 80 N until fracture or 240,000 load applications. The mean number of load applications required for temporary restoration until the fracture was 155,455 in the PMMA-G group versus 51,136 in the PMMA group. Resistance to fracture under cyclic loading was three times greater in the PMMA-G group than in the PMMA group.

Effect of microwave polymerization on the thermomechanical and surface properties of ocular prosthetic acrylic resins.

Polymerization conditions affect the physical-mechanical properties of acrylic resins used for craniofacial prostheses. The aim of this study was to evaluate the effect of microwave polymerization on the thermomechanical properties and surface morphology of ocular prostheses fabricated with polymethyl methacrylate (PMMA). PMMA discs were polymerized with microwave energy and with conventional heat polymerization (CHP) method. Ocular prostheses were fabricated to determine whether there were changes according to the polymerization method. The surface morphology and roughness were observed under SEM and AFM. The Vickers Hardness number (VHN) and flexural strength were measured. Thermal properties were evaluated with TGA/DSC, and chemical composition with FTIR. The PMMA acrylic resin polymerized with microwave energy showed a smooth surface with some relief areas. In the internal surface of the ocular prosthesis with microwave energy the PMMA is more compact. The mean roughness values were higher and statistically significant with CHP (P <0.05), while the surface hardness and flexural strength were higher with microwave energy (P <0.05). There were no changes in the calorimetry with either method, TGA showed an exothermic peak around 120°C with CHP method. PMMA polymerized with microwave energy improved the mechanical and surface properties of the ocular prostheses.

Does Multifunctional Acrylate's Addition to Methacrylate Improve Its Flexural Properties and Bond Ability to CAD/CAM PMMA Block?

This study investigated the effects of a multifunctional acrylate copolymer-Trimethylolpropane Triacrylate (TMPTA) and Di-pentaerythritol Polyacrylate (A-DPH)-on the mechanical properties of chemically polymerized acrylic resin and its bond strength to a CAD/CAM polymethyl methacrylate (PMMA) disk. The methyl methacrylate (MMA) samples were doped with one of the following comonomers: TMPTA, A-DPH, or Trimethylolpropane Trimethacrylate (TMPTMA). The doping ratio ranged from 10 wt% to 50 wt% in 10 wt% increments. The flexural strength (FS) and modulus (FM) of PMMA with and without comonomer doping, as well as the shear bond strength (SBS) between the comonomer-doped PMMA and CAD/CAM PMMA disk, were evaluated. The highest FS (93.2 ± 4.2 MPa) was obtained when doped with 20 wt% of TMPTA. For TMPTMA, the FS decreased with the increase in the doping ratio. For SBS, TMPTA showed almost constant values (ranging from 7.0 to 8.2 MPa) regardless of the doping amount, and A-DPH peaked at 10 wt% doping (8.7 ± 2.2 MPa). TMPTMA showed two peaks at 10 wt% (7.2 ± 2.6 MPa) and 40 wt% (6.5 ± 2.3 MPa). Regarding the failure mode, TMPTMA showed mostly adhesive failure between the CAD/CAM PMMA disk and acrylic resin while TMPTA and A-DPH showed an increased rate of cohesive or mixed failures. Acrylate's addition as a comonomer to PMMA provided improved mechanical properties and bond strength to the CAD/CAM PMMA disk.

Pre-Disinfection of Poly-Methyl-Methacrylate (PMMA) Reduces Volatile Sulfides Compounds (VSC) Production in Experimental Biofilm In Vitro

Temporary dental crowns and bridges are commonly made of poly-methylmethacrylate (PMMA), a porous material attracting the microbial biofilm associated with malodor production. The purpose of the present study was to test pre-disinfection of PMMA on malodor-related parameters in an experimental oral biofilm. PMMA discs were pre-soaked in anti-malodor disinfecting solutions and controls: (i) Saline, (ii) essential oils (EO), (iii) herbal extracts (HE), and (iv) chlorhexidine (CHX). Following, discs were subjected to a salivary incubation assay and monitored for malodor-producing bacteria within the biofilm using confocal microscopy (CLSM), malodor production (organoleptic scale 0–5), volatile sulfide levels (Halimeter), and salivary protein degradation (SDS-PAGE). Results showed that disinfection solutions were significantly effective in reducing malodor-related parameters (CHX &gt; HE &gt; EO &gt; Saline). Taken together, these results suggest that pre-disinfection may help to reduce malodor production in PMMA temporary dental restorations.

Top-down design and fabrication with digital technology of removable partial dentures incorporating custom abutments: A dental technique

A novel design of removable partial dentures (RPDs) is described wherein custom abutments are incorporated into the RPD framework. The artificial teeth and custom abutments are designed by using a computer-aided design (CAD) software program. Subsequently, the RPD framework is designed and merged to the custom abutments in the CAD software program to form a single unit. This modified framework is additively manufactured in metal by using a 3D printer. Thereafter, the framework is adapted to the definitive cast and scanned by using a laboratory scanner. The scanned file is imported into the CAD software program, and the artificial teeth are redesigned. After fabricating each artificial tooth from a polymethylmethacrylate disk and artificial tooth and denture-base assemblies from a wax disk, the RPD is injection molded. This RPD design and fabrication workflow enables a top-down approach by prioritizing the shape and arrangement of the artificial teeth and facilitates their replacement.

2-methacryloyloxyethyl phosphorylcholine polymer treatment prevents Candida albicans biofilm formation on acrylic resin.

We aimed to evaluate the effectiveness of photoreactive 2-methacryloyloxyethyl phosphorylcholine (MPC) in inhibiting Candida albicans biofilm formation on polymethyl methacrylate (PMMA) and assess its mechanism and need for re-application by evaluating its interaction with salivary mucin and durability during temperature changes. PMMA discs were used as specimens. The MPC coating was applied using the spray and cure technique for the treatment groups, whereas no coating was applied to the control. The MPC treatment (MT) groups were further differentiated based on the number of thermal cycles involved (0, 1000, 2500, and 5000). The optical density was measured to assess mucin adsorption (MA). Contact angle (CA) was calculated to evaluate surface hydrophilicity. The presence of MPC components on the PMMA surface was assessed using X-ray photoelectron spectroscopy (XPS). C. albicans biofilms were evaluated qualitatively (scanning electron microscope images) and quantitatively (colony-forming units (CFUs)). Statistical analysis was conducted using two-way analysis of variance and Tukey's multiple comparison test. MA rate and CA increased significantly in the MT groups, which exhibited significantly fewer CFUs and thinner biofilms than those of the control group. Based on the XPS, MA, and CFU evaluations, the durability and efficacy of the MPC coating were considered stable up to 2500 thermal cycles. Additionally, a significant interaction was observed between mucin concentration and MPC efficacy. The photoreactive MPC coating, which was resistant to temperature changes for approximately 3 months, effectively prevented C. albicans biofilm formation by modifying surface hydrophilicity and increasing mucin adsorption.

Comparative Analysis of Biofilm Formation on Materials Used for the Fabrication of Implant Supported Prostheses.

Background:Zirconia and other dental pottery, heat-restored polymethyl methacrylate, titanium and other metal amalgams, or a mix of these materials are utilized to fix inserts. It is important to choose a material that is resistant to bacterial colonization for implant-supported prostheses, but durability and aesthetics are important factors as well.Aim:Biofilm generation on materials used in implant-supported dental prosthesis manufacturing was an objective of this investigation.Methods and Materials:In this study, 90 discs were prepared. These discs were divided into three groups: group PMMA, group Y-TZP, and group CP-Ti. Each group consisted of 30 discs. As helpful materials, 30 discs (D = 15 mm, H = 3 mm) each were created from either monetarily unadulterated titanium (CP-Ti), yttria tetragonal zirconia polycrystal (YTZP), or hotness-restored polymethyl methacrylate (PMMA). The examples were cleaned as per acknowledged practices. The non-contact profilometer (NPFLEX, Bruker, UK) was utilized to survey the surface rougness of each disc, and the outcomes were accounted for as Ra (m). An assortment of gram-negative microbes, including Aggregatibacter actinomycetemcomitans, Tannerella forsythia, Porphyromonas gingivalis, Prevotella intermedia, and Tannerella albicans, were refined close by cleaned discs produced using heat-relieved PMMA, Y-TZP, or CP-Ti to see which type of biofilm is shaped best. CFU/mL was the unit of estimation (state framing units per milliliter).Results:Y-TZP discs have a substantially higher Ra (349 41 m) than PMMA and CP-Ti discs. Some bacteria that have been associated with peri-mucositis and peri-implantitis may be less prevalent on Y-TZP or CP-Ti discs. Biofilm development must be considered while making implant-supported prostheses using Y-TZP and CP-Ti.Conclusion:Y-TZP and CP-Ti are preferred materials for implant-supported prosthesis production because of biofilm development.

CAD/CAM Polimerlerinin (PEEK/PMMA) ve Geleneksel PMMA Materyallerinin Bazı Mekanik Özelliklerinin Değerlendirilmesi: İn Vitro Çalışma

Objective: The present study aims to investigate the mechanical properties of base materials [polymethyl methacrylate (PMMA)/polyether ether ketone (PEEK)] fabricated with computeraided design/computer-aided manufacturing (CAD/CAM) and heatpolymerized conventional base materials. Material and Methods: Two different base polymers milled with CAD/CAM (Yamahachi PMMA Disk and Juvora Dental Disk PEEK) and heat-polymerized acrylic resin (Meliodent PMMA) were used in this study. A total of 120 specimens were prepared with 10 specimens in each subgroup of the test materials. Half of the test specimens were stored in distilled water, while the other half were subjected to a thermal cycle. After the thermal cycle, the flexural strength, elasticity module, and, surface hardness of all test specimens was evaluated. The Mann-Whitney U and Kruskal-Wallis tests were used in the analysis of the data. Results: According to the findings of flexural strength and elasticity module of the test specimens, the highest to lowest value ranking was as follows: CAD/CAM PEEK>CAD/CAM PMMA>heat-polymerized PMMA. In the PMMA group produced with CAD/CAM, surface hardness values were significantly higher in the thermocycle applied test specimens compared to those stored in distilled water (p<0.001). Conclusion: CAD/CAM PMMA and PEEK materials were compared with the heat-polymerized test specimens found to show better mechanical properties.

Hydrogen peroxide potentiates antimicrobial photodynamic therapy in eliminating Candida albicans and Streptococcus mutans dual-species biofilm from denture base

BackgroundCandida albicans (C.albicans) is the primary pathogen of denture biofilm. Moreover, it could establish a cross-kingdom relationship with bacteria to enhance its virulence and resistance to antifungal drugs. This study aimed to investigate the efficacy of antimicrobial photodynamic therapy (aPDT) in combination with hydrogen peroxide (H2O2) against C.albicans and Streptococcus mutans (S.mutans) dual-species biofilm formed on polymethyl methacrylate (PMMA) disk, and explore its involved mechanisms. MethodsC.albicans and S.mutans were grown on PMMA disk for 48 h to form biofilm and received different treatments. The treatments included:1) phosphate-buffered saline (PBS) group,2) 100 mM H2O2 group,3) aPDT group,4) aPDT+ H2O2 and 5) H2O2+aPDT group. Colony forming units (CFU), 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT), and scanning electron microscope (SEM) were used to evaluate the antimicrobial effects. Extracellular polysaccharide substance (EPS) production and observation, cell permeability of biofilm, and uptake of toluidine blue O (TBO) by biofilm were assessed to investigate the involved mechanism. ResultsThere was no significant difference between PBS group and H2O2 group in viable microorganisms and metabolic activity of biofilm. The treatment protocols containing aPDT group reduced microorganism numbers and metabolic activity when compared to PBS group or H2O2 group (P<0.05). H2O2+aPDT treatment showed the highest antimicrobial efficacy in comparison with other treatments (P<0.05). Pretreatment with H2O2 could decrease EPS production and enhance cell permeability, leading to increased TBO uptake in biofilm. ConclusionPretreatment with H2O2 improved aPDT efficiency in eliminating dual-species biofilm from PMMA disk by reducing EPS amount, enhancing cell permeability, and increasing TBO uptake.

Effect of Low Nanodiamond Concentrations and Polymerization Techniques on Physical Properties and Antifungal Activities of Denture Base Resin.

Background: Denture base resin has some drawbacks. This study investigated the impact of nanodiamonds (ND) and autoclave polymerization on the surface characteristics, translucency, and Candida albicans adherence in polymethyl methacrylate (PMMA) denture base resin after thermocycling. Methods: Heat-polymerized PMMA discs (15 × 2 mm) with a total sample size n = 160 were studied. Specimens were categorized into two main groups (N = 80): conventional water-bath-polymerized PMMA (CP/PMMA) and autoclave-polymerized PMMA (AP/PMMA). Each group was subdivided according to the ND concentration into four groups (n = 20): unmodified PMMA as a control, and 0.1%, 0.25%, and 0.5% ND–PMMA. Scanning electron microscopy (SEM) was used to inspect the morphology of the ND and the ND–PMMA mixtures before heat polymerization. The specimens were exposed to thermal cycling (5000 cycles at 5 and 55 °C), then surface roughness was measured with a non-contact optical interferometric profilometer, contact angle with an automated goniometer, and translucency using a spectrophotometer. Colony-forming units (CFU) were used to determine the adherence of Candida albicans cells to the specimens. ANOVA and Tukey post hoc tests for pairwise comparison were utilized for the statistical analysis (α = 0.05). Results: Surface roughness was significantly reduced with ND addition to CP/PMMA (p ˂ 0.001), while the reduction was not statistically significant in AP/PMMA (p = 0.831). The addition of ND significantly reduced the contact angle, translucency, and Candida albicans count of CP/PMMA and AP/PMMA (p ˂ 0.001). The incorporation of ND in conjunction with autoclave polymerization of PMMA showed significant reduction in all tested properties (surface roughness, contact angle and Candida albicans adherence) except translucency (p = 0.726). Conclusions: ND addition to PMMA and autoclave polymerization improved the surface properties with respect to antifungal activities, while the translucency was adversely affected.

Flexural and fatigue properties of polyester disk material for milled resin clasps.

To evaluate the flexural and fatigue properties of a polyester disk material used in milled resin clasps of removable partial dentures, experimental polyester disk (mPE), injection-molded polyester (iPE), and polymethyl methacrylate disk (mPMMA) were examined by three-point bending tests and cyclic fatigue tests at 0.75 or 1.50 mm deflection. The mPE exhibited significantly higher flexural strength than the iPE (p<0.05). Meanwhile, the mPMMA displayed higher flexural modulus and strength than the polyesters. The mPE exhibited a significantly lower residual strain than the iPE at the cyclic 0.75 mm deflection (p<0.05); however, microcracks were observed in the mPE at the 1.50 mm deflection. The mPMMA showed a high residual strain at the 0.75 mm deflection and fractured within 1,000 cycles at the 1.5 mm deflection. The higher flexural strength and lower residual strain of the mPE compared with the iPE suggest the advantages of milled resin clasps within a limited deflection.

Effect of Printing Layer Thickness on the Trueness and Margin Quality of 3D-Printed Interim Dental Crowns

The information in the literature on the effect of printing layer thickness on interim 3D-printed crowns is limited. In the present study, the effect of layer thickness on the trueness and margin quality of 3D-printed composite resin crowns was investigated and compared with milled crowns. The crowns were printed in 3 different layer thicknesses (20, 50, and 100 μm) by using a hybrid resin based on acrylic esters with inorganic microfillers or milled from polymethylmethacrylate (PMMA) discs and digitized with an intraoral scanner (test scans). The compare tool of the 3D analysis software was used to superimpose the test scans and the computer-aided design file by using the manual alignment tool and to virtually separate the surfaces. Deviations at different surfaces on crowns were calculated by using root mean square (RMS). Margin quality of crowns was examined under a stereomicroscope and graded. The data were evaluated with one-way ANOVA and Tukey HSD tests. The layer thickness affected the trueness and margin quality of 3D-printed interim crowns. Milled crowns had higher trueness on intaglio and intaglio occlusal surfaces than 100 μm-layer thickness crowns. Milled crowns had the highest margin quality, while 20 μm and 100 μm layer thickness printed crowns had the lowest. The quality varied depending on the location of the margin.