Polymer Domains Research Articles

Molecular models of PM6 for non-fullerene acceptor organic solar cells: How DAD and ADA structures impact charge separation and charge recombination.

The quadrupole moment of a non-fullerene acceptor (NFA) generated by the constituent electron donor (D) and acceptor (A) units is a significant factor that affects the charge separation (CS) and charge recombination (CR) processes in organic photovoltaics (OPVs). However, its impact on p-type polymer domains remains unclear. In this study, we synthesized p-type molecules, namely acceptor-donor-acceptor (ADA) and donor-acceptor-donor (DAD), which are components of the benchmark PM6 polymer (D: benzodithiophene and A: dioxobenzodithiophene). Planar heterojunction films, a model of bulk heterojunction, were prepared using ADA, DAD, and PM6 as the bottom p-type layers and Y6 NFA as the top n-type layer. Flash-photolysis time-resolved microwave conductivity, femtosecond transient absorption spectroscopy, and quantum mechanical calculations were employed to probe the charge carrier dynamics. Our findings reveal that while the subtle difference in quadrupole moment and energy gradient of the p-type materials has a minimal influence on CS, the molecular type (ADA or DAD) significantly affects the bulk CR. This study expands the understanding of how the p-type component and its conformation at the p/n interface impact the CS and CR in OPVs, highlighting the critical role of molecular donors in optimizing device performance.

On the Use of Reflection Polarized Optical Microscopy for Rapid Comparison of Crystallinity and Phase Segregation of P3HT:PCBM Thin Films.

Rapid, nondestructive characterization techniques for evaluating the degree of crystallinity and phase segregation of organic semiconductor blend thin films are highly desired for in-line, automated optoelectronic device fabrication facilities. Here, it is demonstrated that reflection polarized optical microscopy (POM), a simple technique capable of imaging local anisotropy of materials, is capable of determining the relative degree of crystallinity and phase segregationof thin films of polymer:fullerene blends. While previous works on POM of organic semiconductors have largely employed the transmission geometry, it is demonstrated that reflection POM provides 3× greater contrast. The optimal configuration is described to maximize contrast from POM images of polymer:fullerene films, which requires Köhler illumination and slightly uncrossed polarizers, with an uncrossing angle of ±3°. It is quantitatively demonstrated that contrast in POM images directly correlates with 1) the degree of polymer crystallinity and 2) the degree of phase segregation between polymer and fullerene domains. The origin of the bright and dark domains in POM is identified as arising from symmetry-broken liquid crystalline phases (i.e., dark conglomerates), and it is proven that they have no correlation with surface topography. The use of reflection POM as a rapid diagnostic tool for automated device fabrication facilities is discussed.

Phase-separated polymer blends for controlled drug delivery by tuning morphology

Controlling drug release rate and providing physical and chemical stability to the active pharmaceutical ingredient are key properties of oral solid dosage forms. Here, we demonstrate a formulation strategy using phase-separated polymer blends where the morphology provides a route for tuning the drug release profile. By utilising phase separation of a hydrophobic and a hydrophilic polymer, the hydrophilic component will act as a channelling agent, creating a porous network upon dissolution that will dictate the release characteristics. With ptychographic X-ray tomography and scanning transmission X-ray microscopy we reveal how the morphology depends on both polymer fraction and presence of drug, and how the drug is distributed over the polymer domains. Combining X-ray imaging results with dissolution studies reveal how the morphologies are correlated with the drug release and showcase how tuning the morphology of a polymer matrix in oral formulations can be utilised as a method for controlled drug release.

Polarization-dependent photoemission electron microscopy for domain imaging of inorganic and molecular materials.

Polarization-dependent photoemission electron microscopy (PD-PEEM) exploits spatial variation in the optical selection rules of materials to image domain formation and material organization on the nanoscale. In this Perspective, we discuss the mechanism of PD-PEEM that results in the observed image contrast in experiments and provide examples of a wide range of material domain structures that PD-PEEM has been able to elucidate, including molecular and polymer domains, local electronic structure and defect symmetry, (anti)ferroelectricity, and ferromagnetism. In the end, we discuss challenges and new directions that are possible with this tool for probing domain structure in materials, including investigating the formation of transient ordered states, multiferroics, and the influence of molecular and polymer order and disorder on excited state dynamics and charge transport.

Moisture sorption and mechanical properties of polymer-cement waterproofing membranes investigated by LF NMR

This study investigates the impacts of environmental humidity on moisture absorption and mechanical properties of polymer-based waterproofing membranes. Membranes of polymer-CaCO3, polymer-white cement composites and pure polymer were used for measurements after treated in different relative humidities (RHs). Results indicate that the humidity treatment greatly changes the mechanical properties of the membranes and increasing RH from 0 % to 100 % leads to reduction of tensile strength by 60–80 %, which is believed to originate from the plasticizing effect of the absorbed moisture. LF NMR (Low field NMR) enables quantification of moisture distribution in the polymer-filler composites and three types of water, i.e. the water stored inside polymer matrix (O/O water), the water located in interfacial regions between polymer phase and fillers (I/O water), and the free water in air voids are detected with increasing T2 values. The absorbed moisture majorly accumulates in the O/O interfacial region during the humidity treatments with RH of 0∼80 %, which is because of the larger O/O interfacial area compared with the I/O interface. A large amount of free water appears only at RH of 100 %. A core-shell structure of the polymer domains with dry core and moisturized shell, is interestingly found during the moisture absorption process of the membranes, based on the LF NMR measurements using MSE sequence. It is surprisingly found that the drop of tensile strength of the membranes upon moisture absorption is majorly related to the growing shell thickness of the polymer domains whereas the moisture accumulated in the I/O interfacial region plays a minor role.

Wetting Kinetics-Controlled Interplay between Nanoparticles and Polymer Domains in Multiphase Polymer Blends

Wetting Kinetics-Controlled Interplay between Nanoparticles and Polymer Domains in Multiphase Polymer Blends

Mechanism for controlled assembly of transcriptional condensates by Aire

Transcriptional condensates play a crucial role in gene expression and regulation, yet their assembly mechanisms remain poorly understood. Here, we report a multi-layered mechanism for condensate assembly by autoimmune regulator (Aire), an essential transcriptional regulator that orchestrates gene expression reprogramming for central T cell tolerance. Aire condensates assemble on enhancers, stimulating local transcriptional activities and connecting disparate inter-chromosomal loci. This functional condensate formation hinges upon the coordination between three Aire domains: polymerization domain caspase activation recruitment domain (CARD), histone-binding domain (first plant homeodomain (PHD1)), and C-terminal tail (CTT). Specifically, CTT binds coactivators CBP/p300, recruiting Aire to CBP/p300-rich enhancers and promoting CARD-mediated condensate assembly. Conversely, PHD1 binds to the ubiquitous histone mark H3K4me0, keeping Aire dispersed throughout the genome until Aire nucleates on enhancers. Our findings showed that the balance between PHD1-mediated suppression and CTT-mediated stimulation of Aire polymerization is crucial to form transcriptionally active condensates at target sites, providing new insights into controlled polymerization of transcriptional regulators.

Dielectric Property Tuning via Electric Field Alignment in Mxene (Ti3C2)-Based Polymer Nanocomposites

Orientation control is crucial for fine-tuning the functional properties of two-dimensional (2D) nanomaterials. MXene (Ti3C2) alignment has drawn significant attention lately as the targeted properties can be controlled by manipulating the structural anisotropy. However, controlled MXene nanosheet orientation inside the polymer matrix is a complex and less understood mechanism. In this study, we applied an in-plane electric field to align the MXene nanosheets vertically inside the semicrystalline polyvinylidene fluoride (PVDF) (Tg⁓ -35°C) matrix in situ, where the amorphous phase assisted the electric field alignment at room temperature. These vertical orientations of the nanosheets were confirmed directly using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). Our study reveals a significant correlation between MXene-orientation and dielectric property enhancement. PVDF- 5 wt.% MXene demonstrated the highest dielectric permittivity increase of ⁓500% because of the maximum surface polarization of the nano-capacitors inside the matrix. Interestingly, the loss value shows a sharp jump after the 5 wt. % MXene concentration, demonstrating a percolative network formation. Notably, our nanocomposite exhibited a low loss before (0.07) and after (0.66) applying the electric field, even at a high MXene concentration (20wt.%). Finally, to understand the effect of polymer domain structure on the electric field-induced orientation effect, we conducted a comparative study between non-ferroelectric poly vinyl alcohol (PVA) and ferroelectric (PVDF) polymer-based MXene nanocomposites. Interestingly, we observed a synergistic effect of the polymer chain and MXene orientation on the permittivity enhancement in the ferroelectric polymer-based nanocomposites at both high and low frequencies. This study provides fundamental insights for designing hybrid solid-state dielectric films for next-generation flexible electronics.

Visualizing the Heterogeneity in Homogeneous Supramolecular Polymers.

The dynamic properties of supramolecular polymers enable new functionality beyond the limitations of conventional polymers. The mechanism of the monomer exchange between different supramolecular polymers is proposed to be closely associated with local disordered domains within the supramolecular polymers. However, a direct detection of such heterogeneity has never been experimentally probed. Here, we present the direct visualization of the local disordered domains in the backbone of supramolecular polymers by a super-resolution microscopy technique: Nile Red-based spectrally resolved point accumulation for imaging in nanoscale topography (NR-sPAINT). We investigate the local disordered domains in trisamide-based supramolecular polymers comprising a (co)assembly of benzene-1,3,5-tricarboxamide (BTA) and a variant with one of the amide bonds inverted (iBTA). The NR-sPAINT allows us to simultaneously map the spatial distribution and polarity of the local disordered domains along the polymers with a spatial precision down to ∼20 nm. Quantitative autocorrelation and cross-correlation analysis show subtle differences in the spatial distribution of the disordered domains between polymers composed of different variants of BTA monomers. Further, statistical analysis unraveled high heterogeneity in monomer packing at both intra- and interpolymer levels. The results reported here demonstrate the necessity of investigating the structures in soft materials at nanoscale to fully understand their intricacy.

Immiscible Polymer Blends Made from Industrial Shredder Residue Mixed Plastic with and without Melt Blending.

The processing of an immiscible polymer blend using melt blending (i.e., extrusion) often results in a polymer material with inferior mechanical performance compared with its virgin counterparts. Here, we report and compare the properties of immiscible polymer blends produced from industrial mixed plastic waste from shredder residue comprising at least four different polymers (acrylonitrile butadiene styrene, polystyrene, polypropylene, and polyethylene) with and without a prior melt-blending step employed. As anticipated, mixed plastic blend produced with a prior melt-blending step exhibited a more homogeneous microstructure, resulting in brittleness, poor work of fracture, and single-edge notched fracture toughness with a flat R-curve. Without the intimate polymers mixing arising from melt blending, the resulting mixed plastic blend was found to possess a more heterogeneous concentric ellipsoid microstructure with large single polymer domains. This mixed plastic blend demonstrated progressive failure under uniaxial tensile loading, along with a more ductile single-edge notched fracture toughness response accompanied by a growing R-curve. Digital image correlation and fractographic analysis revealed that melt blending created a large number of incompatible polymer boundaries that acted as stress concentration points, leading to brittleness and earlier onset catastrophic failure. The more heterogeneous mixed plastic blend produced without using a prior melt-blending step contains a smaller number of incompatible polymer boundaries. Additionally, the presence of larger single polymer domains also implies that the mechanical characteristics of the single polymer can be exploited in the immiscible mixed plastic blend. Our work opens up a simple pathway to add value to mixed plastic waste from shredder residue for use in engineering applications, diverting them away from landfill or incineration.

Deciphering the factors influencing electric field mediated polymerization and depolymerization at the solution–solid interface

Strong and oriented electric fields are known to influence structure as well as reactivity. The strong electric field (EF) between the tip of a scanning tunneling microscope (STM) and graphite has been used to modulate two-dimensional (2D) polymerization of aryl boronic acids where switching the polarity of the substrate bias enabled reversible transition between self-assembled molecular networks of monomers and crystalline 2D polymer (2DP) domains. Here, we untangle the different factors influencing the EF-mediated (de)polymerization of a boroxine-based 2DP on graphite. The influence of the solvent was systematically studied by varying the nature from polar protic to polar aprotic to non-polar. The effect of monomer concentration was also investigated in detail with a special focus on the time-dependence of the transition. Our experimental observations indicate that while the nucleation of 2DP domains is not initiated by the applied electric field, their depolymerization and subsequent desorption, are a consequence of the change in the polarity of the substrate bias within the area scanned by the STM tip. We conclude that the reversible transition is intimately linked to the bias-induced adsorption and desorption of the monomers, which, in turn, could drive changes in the local concentration of the monomers.

Self-Sorting of Interfacial Compatibility in MOF-Based Mixed Matrix Membranes.

Metal-organic framework (MOF)-based mixed matrix membranes (MMMs) have shown great promises to overcome the performance upper limit of polymeric membranes for various gas separation processes. However, the gas separation properties of the MMMs largely depend on the MOF-polymer interfacial compatibility which is a metric difficult to quantify. In most cases, whether a MOF filler and a polymer matrix make a good pair is not revealed until the gas transport experiments are performed. This is because there is a lack of characterization techniques to directly probe the MOF-polymer interfacial compatibility. In this work, we demonstrate a self-sorting method to rank the interface compatibility among several MOF-polymer pairs. By mixing one MOF with two polymers in an MMM, the demixing of two polymers will form two polymer domains. The MOF particles will preferably partition into the "preferred" polymer domain due to their higher interfacial affinity. By scanning different polymer pairs, a rank of MOF-polymer interfacial compatibility from high to low can be obtained. Moreover, based on this ranking, it was also found that a highly compatible MOF-polymer pair suggested by this method also corresponds to a more predictable MMM gas separation performance.

Self‐Sorting of Interfacial Compatibility in MOF‐Based Mixed Matrix Membranes

AbstractMetal–organic framework (MOF)‐based mixed matrix membranes (MMMs) have shown great promises to overcome the performance upper limit of polymeric membranes for various gas separation processes. However, the gas separation properties of the MMMs largely depend on the MOF‐polymer interfacial compatibility which is a metric difficult to quantify. In most cases, whether a MOF filler and a polymer matrix make a good pair is not revealed until the gas transport experiments are performed. This is because there is a lack of characterization techniques to directly probe the MOF‐polymer interfacial compatibility. In this work, we demonstrate a self‐sorting method to rank the interface compatibility among several MOF‐polymer pairs. By mixing one MOF with two polymers in an MMM, the demixing of two polymers will form two polymer domains. The MOF particles will preferably partition into the “preferred” polymer domain due to their higher interfacial affinity. By scanning different polymer pairs, a rank of MOF‐polymer interfacial compatibility from high to low can be obtained. Moreover, based on this ranking, it was also found that a highly compatible MOF‐polymer pair suggested by this method also corresponds to a more predictable MMM gas separation performance.

Direct Imaging of the Crystalline Domains and Their Orientation in the PS-b-PEO Block Copolymer with 4D-STEM.

The arrangement of crystalline domains in semicrystalline polymers is key to understanding how to optimize the nanostructured morphology for enabling better properties. For example, in polystyrene-b-poly(ethylene oxide) (PS-b-PEO), the degree of crystallinity and arrangement of the crystallites within the PEO phase plays a crucial role in determining the physical properties of the electrolyte. Here, we used four-dimensional scanning transmission electron microscopy to directly visualize the crystal domains within the PEO-rich region of the PS-b-PEO block copolymer and show the relative angle of the domain with respect to the PEO-PS interface. As demonstrated here, our analysis method is applicable to other electron-beam sensitive materials, especially semicrystalline polymers, to unveil their local phase condition and distribution.

Microphase Separation 3D Printing of Binary Inorganic Polymer Precursors to Prepare Nanostructured Carbon‐Ceramic Multimaterials

AbstractTraditionally, combining carbon and ceramic materials has been challenging due to their different chemical and physical properties. Despite the development of numerous methodologies for their synthesis, these techniques frequently necessitate intricate, multi‐stage protocols and specialized equipment. This study introduces a novel approach for fabricating nanostructured carbon‐ceramic multimaterials through polymerization‐induced microphase separation 3D printing. By combining inorganic precursors, polycarbosilane, and acrylonitrile (AN) within a photocurable resin, heterogeneous nanostructured materials composed of PAN‐preceramic and sacrificial polymer phases are 3D printed. Upon pyrolysis, PAN‐preceramic domains transformed into a carbon‐ceramic matrix while sacrificial polymer domains thermally decomposed to yield nanoscale voids. The utilization of synchrotron X‐ray spectroscopy and microscopy techniques revealed that the phase compositions and microstructure of the resulting multi‐materials are significantly influenced by the initial composition of the resins. The co‐existence of ceramic and carbon phases within a single 3D printed material brought together a combination of properties from both phases, such as the low thermal conductivity of ceramics and the relatively high electrical conductivity of carbon, along with the exceptional chemical resistance. The insights into the microstructure, atomic configuration, and property relationships of the resulting materials have broad implications for the development of multi‐phase nanostructured hybrid materials.

Stretchable Electrodes with Interfacial Percolation Network.

Stretchable electrodes are an essential component that determines the functionality and reliability of stretchable electronics, but face the challenge of balancing conductivity and stretchability. This work proposes a new conducting concept called the interfacial percolation network (PN) that results in stretchable electrodes with high conductivity, large stretchability, and high stability. The interfacial PN is composed of a 2D silver nanowires (AgNWs) PN and a protruding 3D AgNWs PN embedded on the surface and in the near-surface region of an elastic polymer matrix, respectively. The protruded PN is obtained by changing the arrangements of AgNWs from horizontal to quasi-vertical through introducing foreign polymer domains in the near-surface region of the polymer matrix. The resulting electrode achieves a conductivity of 13500 S cm-1 and a stretchability of 660%. Its resistance changes under stretched conditions are orders of magnitude lower than those of conventional 2D PN and 2D + 3D PN. An interfacial PN electrode made from liquid metal remained its conductivity at46750 S cm-1 after the electrode underwent multiple stretch-release cycles with a deformation of >600%. The concept of interfacial PN provides fruitful implications for the design of stretchable electronics.

Statistical field theory of polarizable polymer chains with nonlocal dipolar interactions.

The electromechanical response of polymeric soft matter to applied electric fields is of fundamental scientific interest as well as relevant to technologies for sensing and actuation. Several existing theoretical and numerical approaches for polarizable polymers subject to a combined applied electric field and stretch are based on discrete monomer models. In these models, accounting for the interactions between the induced dipoles on monomers is challenging due to the nonlocality of these interactions. On the other hand, the framework of statistical field theory provides a continuous description of polymer chains that potentially enables a tractable way to account for these interactions. However, prior formulations using this framework have been restricted to the case of weak anisotropy of the monomer polarizability. This paper formulates a general approach based in the framework of statistical field theory to account for the nonlocal nature of the dipolar interactions without any restrictions on the anisotropy or nonlinearity of the polarizability of the monomer. The approach is based on three key elements: (1) the statistical field theory framework, in which the discrete monomers are regularized to a continuous dipole distribution, (2) a replacement of the nonlocal dipole-dipole interactions by the local electrostatics partial differential equationwith the continuous dipole distribution as the forcing, and (3) the use of a completely general relation between the polarization and the local electric field. Rather than treat the dipole-dipole interactions directly, the continuous description in the field theory enables the computationally tractable nonlocal-to-local transformation. Further, it enables the use of a realistic statistical-mechanical ensemble wherein the average far-field applied electric field is prescribed, rather than prescribing the applied field at every point in the polymer domain. The model is applied, using the finite element method, to study the electromechanical response of a polymer chain in the ensemble with fixed far-field applied electric field and fixed chain stretch. The nonlocal dipolar interactions are found to increase, over the case where dipole-dipole interactions are neglected, the magnitudes of the polarization and electric field by orders of magnitude as well as significantly change their spatial distributions. Next, the effect of the relative orientation between the applied field and the chain on the local electric field and polarization is studied. The model predicts that the elastic response of the polymer chain is linear, consistent with the Gaussian approximation, and largely unchanged by the orientation of the applied electric field, though the polarization and local electric field distributions are significantly impacted.

Sequential Infiltration Synthesis of Silicon Dioxide in Polymers with Ester Groups-Insight from In Situ Infrared Spectroscopy.

New strategies to synthesize nanometer-scale silicon dioxide (SiO2) patterns have drawn much attention in applications such as microelectronic and optoelectronic devices, membranes, and sensors, as we are approaching device dimensions shrinking below 10 nm. In this regard, sequential infiltration synthesis (SIS), a two-step gas-phase molecular assembly process that enables localized inorganic material growth in the targeted reactive domains of polymers, is an attractive process. In this work, we performed in situ Fourier transform infrared spectroscopy (FTIR) measurements during SiO2 SIS to investigate the reaction mechanism of trimethylaluminum (TMA) and tri(tert-pentoxy) silanol (TPS) precursors with polymers having ester functional groups (poly(methyl methacrylate) (PMMA), poly(ethyl methacrylate) (PEMA), polycaprolactone (PCL), and poly(t-butyl methacrylate) (PBMA)), for the purpose of growing patterned nanomaterials. The FTIR results show that for PMMA and PEMA, a lower percentage of functional groups participated in the reactions and formed weak and unstable complexes. In contrast, almost all functional groups in PCL and PBMA participated in the reactions and showed stable and irreversible interactions with TMA. We discovered that the amount of SiO2 formed is not directly correlated with the number of interacting functional groups. These insights into the SiO2 SIS mechanism will enable nanopatterning of SiO2 for low-dimensional applications.

Reversible Binding Interfaces Made of Microstructured Polymer Brushes.

The polymer brush architecture of the end-tethered polymer molecules is one of the most widely used efficient methods to regulate interfacial interactions in colloidal systems found in live matter and manufactured materials. Emerging applications of polymer brush structures require solutions to new tasks in the control of interfacial interactions. The rapid development of live cell manufacturing relies on scalable and efficient cell harvesting methods. Stimuli-responsive surfaces made of surface-grafted poly(N-isopropylacrylamide) (PNIPAM) can bind and detach the adherent cell upon changes in temperature and have been used for cell growth and harvesting. The applications are limited by the requirement to satisfy a range of PNIPAM coating characteristics that depend on the dimensions of the integrin complex in the cell membrane and the basal surface. The analysis of the microstructured surfaces, when adhesive and disjoining functions of the microdomains are decoupled, shows that many limitations of PNIPAM one-component coatings can be avoided by using a much broader range of structural characteristics of the microstructured interfaces composed of alternating disjoining PNIPAM domains and adhesive polymeric domains with cell-affinity functional groups. Temperature-controlled reversible adhesion to such microstructured interfaces is studied here experimentally with model systems of solid spherical particles and by employing simulations for solid and soft membranes interacting with the microstructured surfaces to mimic interactions with soft and solid disk-like particles.

Molecular-scale mechanics of a crystalline polyethylene interface formed by projection of carbon nanotube structures

The semicrystalline nature of polymer chains induced by the intrusion of carbon nanotubes (CNTs) is a decisive factor in understanding the properties of interfacial regions. Herein, the structural and mechanical behavior of polyethylene (PE) formed around CNT surfaces were determined using a combination of classical molecular dynamics simulations and subcontinuum-scale analysis. The results suggest that inserting CNTs into the polymer domain forces the PE chains to align along the longitudinal axis of the CNTs. The interface functions as a nucleating agent, and the area occupied by the crystalline phase propagates radially as PE chains are stacked over long distances. The crystalline PE, grown with CNT as the central axis, exhibits extreme mechanical anisotropy, particularly for normal and shear deformations in the transverse direction. Therefore, this study provides an important theoretical guideline for understanding polymeric semi-crystals around CNTs.