Polylactic Acid Matrices Research Articles

Valorization of Cellulosic Waste from Artichoke for Incorporation into Biodegradable Polylactic Acid Matrices.

This study presents the development of ecological compounds using polylactic acid (PLA) and artichoke flour with the aim of obtaining materials with properties like commercial PLA. PLA biocomposites with different concentrations of green artichoke (HV) and boiled artichoke (HH) (1, 3, 5, 7, 10 and 20% by weight) were manufactured through an extrusion and injection process. Structural, mechanical, physical and color tests were carried out to analyze the effect of lignocellulosic particles on the biopolymeric matrix. The Shore D hardness, elongation at break and heat deflection temperature (HDT) of the PLA/HV and PLA/HH samples showed similar values to pure PLA, indicating that high concentrations of both fillers did not severely compromise these properties. However, reductions in the tensile strength, impact strength and Young's modulus were observed, and both flours had increased water absorption capacity. FTIR analysis identified the characteristic peaks of the biocomposites and the ratio of the groups regarding the amount of added filler. The SEM revealed low interfacial adhesion between the polymer matrix and the filler. This study represents a significant advance in the valorization and application of circular economy principles to agricultural waste, such as artichoke waste. PLA/HV biocomposites make a substantial contribution to sustainable materials technology, aligning with the goals of the 2030 agenda to reduce environmental impacts and promote sustainable development.

Improving mechanical properties of PLA with pinus sylvestris char: exploring thermal stability, interfacial strengthening mechanisms, and applications in 3D printing

In the present study, submicron and micron-sized pinus sylvestris char (PS) was applied for the modification of polylactic acid (PLA) and the effect of the properties of PS on the mechanical, thermo-mechanical, and crystallization kinetics of PLA were investigated. As demonstrated, PS could enhance the toughness of the PS-PLA composites by forming interfacial "bridges" to facilitate stress transfer due to its stable lamellar structure and interaction with the PLA matrix. The tensile strength of PLA-PS composites increased by 98% and the bending strength increased by 25% compared to that of pure PLA. The addition of PS significantly increased the energy storage modulus (increased 22%) and loss modulus (increased 30%) of PLA, but led to a decrease in the crystallinity and thermal stability of the composite. In the practical utilization for 3D printing, PS-PLA composites possess good tensile strengths (41.5 MPa), allowing for smooth printing of complex products. This work provides an efficient strategy to modulate the thermodynamic and mechanical properties of PLA matrices by regulating the viscosity of the composites and modulating the interfacial strength with the addition of proper amounts of biochar.

Development of PLA-Waste Paper Biocomposites with High Cellulose Content.

In this study, the integration of paper industry waste with high cellulose content into biocomposites of polylactic acid (PLA), a widely used biobased polymer material, was investigated. The PLA/waste biocomposite samples (0-25 wt.%) were manufactured using the extrusion and injection moulding techniques. The mechanical test results showed improvements in terms of tensile properties and a decrease in impact strength as the percentage of residue increased. The melting temperature decreased, and the crystallinity increased in all biocomposites according to the Differential Scanning Calorimetry (DSC) analysis. Water absorption increased proportionally with the percentage of residue, attributed to the higher cellulose content in the biocomposites, determined by Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) techniques. The scanning electron microscopy (SEM) fracture analysis demonstrated effective reinforcement-matrix cohesion, supporting the previously observed behaviour of the analysed materials. This work highlights the potential of using waste from the paper industry as reinforcement in PLA matrices, opening new perspectives for sustainable applications in the framework of the manufacture of composite materials.

Study on the Properties of PLA- and PP-Based Films for Food Applications Incorporating Orange Peel Extract from Agricultural by-Products.

The aim of this work was to develop active packaging based on polypropylene (PP) and polylactic acid (PLA) matrices using a high value by-product extracted from orange peel as an active compound for food packaging applications. Different films with and without orange peel extract (OPE) based on PP and PLA were obtained via cast extrusion and characterized in terms of their mechanical, thermal, optical, and sealing properties. The films obtained were transparent, but when OPE was incorporated, the transmittance spectrum decreased, causing slight coloration. Mechanical properties were affected by the incorporation of OPE, as elongation at break and tensile strength increased in the cross-direction of the PP film, although the main differences found were related to the polymer itself. In addition, sealing strength also increased via the incorporation of OPE in the PP matrix. However, thermal properties were not affected by OPE in the PP matrix but slightly decreased stability in PLA. Regarding antimicrobial activity in in vitro studies, no inhibition of the growth of Listeria innocua, Saccharomyces cerevisiae, Aspergillus niger, or Escherichia coli was observed. Finally, antioxidant activity was observed in in vitro studies with 2,2-Diphenyl-1picrylhydrazyl (DPPH) radical. The results of this study showed that the obtention of materials with OPE incorporated into the PLA and PP matrix is feasible. The new materials obtained can be used for applications of oxidation-sensitive fresh products.

Evaluation of Heavy Metal Concentrations in Enzyme Embedded Poly Lactic Acid (EPLA) by ICP-OES: Lipase from Candida Rugosa.

Abstract: Enzymes like lipases are essential for catalyzing important reactions in the fields of biotechnology and industrial operations. For quality control and safety evaluations, however, the quantification of these contaminants is crucial because the presence of heavy metals in enzyme preparations can negatively affect their activity and stability. Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES), a key component of this investigation, is used to measure the levels of heavy metals in lipase enzyme preparations embedded in polylactic acid (PLA). The lipase enzyme being studied comes from Candida rugosa, which is well-known for its considerable industrial applications. According to preliminary findings, the lipase enzyme is successfully protected from external heavy metal pollutants by the encapsulating technique, maintaining its enzymatic activity and stability. The lipase-PLA composite had only minimal quantities of heavy metals, according to the ICP-OES study. The research's conclusions show great potential for the creation of reliable and contaminant-free lipase enzyme preparations, which will increase their suitability for usage in a variety of industrial processes and encourage the use of biodegradable polymers, supporting environmental sustainability. By highlighting the significance of quality control and safety assessment through the determination of heavy metal concentrations, this research contributes to the larger field of enzyme biotechnology. It also highlights the potential of Candida Rugosa lipase implanted in PLA matrices for eco-friendly and sustainable biocatalytic applications in sectors ranging from food and pharmaceuticals to biofuel generation and other biodegradable polymers.

Morphological adaptation of expanded vermiculite in polylactic acid and polypropylene matrices for superior thermoplastic composites

AbstractThe morphological transformation of expanded vermiculite (VC) during injection molding with brittle PLA and ductile PP polymers along with its positive and negative contribution to mechanical response is investigated. Polymer/VC mixtures with 30 wt. % VC are prepared by thermokinetic high shear mixing at 4000 rpm without any ex‐situ exfoliation agents or compatibilizers. Obtained composite mixtures are then injection molded onto three‐point bending and tensile test specimens. Performed mechanical tests suggested a significant increase in tensile (110%) and flexural modulus (112%) of PP30VC samples. Presented fractographic and morphological investigations suggested that the root cause of measured improved tensile (36%) and bending strength (26%) of PP is the fibrillation of VC associated with PP/VC interactions under high shear. A similarly increasing trend for tensile (147%) and bending modulus (137%) was observed for PLA30VC samples. Contrary to PP30VC, a decreasing pattern was present in the case of tensile (−40%) and bending strength (−13%) of PLA30VC. The root cause for such reduction is determined to be (i) in situ exfoliation of VC inside PLA matrix and transformation of VC into micrometer‐sized platelets; (ii) evaporation of trapped water/crystalline water in the interlayer region of VC which caused in situ degradation of PLA during manufacturing.Highlights Vermiculite‐loaded PP and PLA composites are produced at high shear. Composites have superior modulus compared to neat polymers. Fibrillation of platelet vermiculite is observed in only the PP matrix.

Investigation of the Effect of Chemical Treatment on the Properties of Colombian Banana and Coir Fibers and Their Adhesion Behavior on Polylactic Acid and Unsaturated Polyester Matrices

In this work, the adhesion behavior of chemically treated banana and coir Colombian fibers embedded in polylactic acid (PLA) and unsaturated polyester resin (UPR) matrices was investigated. Both types of fibers were treated with a 5 wt.% sodium hydroxide solution for one hour. The properties of treated and untreated fibers were determined by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and tensile tests. To evaluate the adhesion behavior of the fibers in PLA and UPR matrices, pull-out tests were performed, and the percentage of broken fibers was determined. The results showed that alkaline treatment improved the fibers’ physicochemical, mechanical, and thermal properties. In addition, the alkaline treatment was able to improve the adhesion behavior of coir and banana fibers to PLA and UPR matrices. The banana fibers showed a percentage of broken fibers of 100%, while the coir fibers showed a slight increase in IFSS value. This behavior is attributed to the improvement in surface roughness due to the removal of non-cellulosic composites and impurities.

A Multicenter Retrospective Study Comparing a Polylactic Acid CAMP With Intact Fish Skin Graft or a Collagen Dressing in the Management of Diabetic Foot Ulcers and Venous Leg Ulcers

Background. Venous leg ulcers (VLUs) and diabetic foot ulcers (DFUs) are examples of chronic wounds that pose an ongoing health care challenge. Despite significant progress in managing such wounds, challenges persist that require innovative solutions. Cellular, acellular, and matrix-like products (CAMPs) are advanced therapies designed to facilitate chronic wound healing. Polylactic acid (PLA) is a synthetic material used in alloplastic CAMPs that has shown promise in the management of burns and traumatic injuries. Objective. To retrospectively assess the effect of PLA in promoting chronic wound healing compared with 2 other well-established CAMPs. Materials and Methods. This retrospective chart review, which was conducted in 3 high-volume wound care clinics, aimed to compare the efficacy of 2 advanced wound care products vs a PLA alloplastic CAMP in promoting DFU and VLU closure. The study included 131 wounds treated with a non-CAMP collagen dressing, fish skin grafts (FSGs), or PLA matrices. Inclusion criteria included single Wagner grade 1 or 2 DFUs or Clinical-Etiology-Anatomy-Pathophysiology classification score C6 VLUs, present for at least 12 to 52 weeks, and measuring between 1 cm² and 20 cm². Patients received weekly treatments with 1 of 3 CAMPs, along with standard care. The primary outcome was time to achieve full healing, and the secondary outcome was the proportion of ulcers healed at 12 weeks. Results. The PLA alloplastic CAMP demonstrated superior outcomes, with a 50% and 20% reduction in time to heal DFUs compared with collagen dressings and FSG, respectively (P < .001). For VLUs, PLA exhibited even more impressive results, achieving 95% and 40% reduction compared with collagen and FSG, respectively (P < .001). PLA allografts displayed a 55% higher rate of full healing by 12 weeks compared with collagen dressings, and a 26% higher rate compared with FSG (P < .001). Conclusion. This study highlights the unique attributes of PLA for achieving wound closure. PLA-based alloplastic CAMPs are promising treatments, offering rapid healing, increased closure rates, and multifaceted benefits for wound healing.

Mechanical and Wear Studies of Boron Nitride-Reinforced Polymer Composites Developed via 3D Printing Technology.

In the realm of 3D printing, polymers serve as fundamental materials offering versatility to cater to a diverse array of final product properties and tailored to the specific needs of the creator. Polymers, as the building blocks of 3D printing, inherently possess certain mechanical and wear properties that may fall short of ideal. To address this limitation, the practice of reinforcing polymer matrices with suitable materials has become a common approach. One such reinforcement material is boron nitride (BN), lauded for its remarkable mechanical attributes. The integration of BN as a reinforcing element has yielded substantial enhancements in the properties of polylactic acid (PLA). The central objective of this research endeavor is the development of polymer composites based on PLA and fortified with boron nitride. This study undertakes the comprehensive exploration of the compatibility and synergy between BN and PLA with a keen focus on examining their resultant properties. To facilitate this, various percentages of boron nitride were incorporated into the PLA matrix, specifically at 5% and 10% by weight. The compounding process involved the blending of PLA and boron nitride followed by the creation of composite filaments measuring 1.75 mm in diameter and optimized for 3D printing. Subsequently, test specimens were meticulously fabricated in adherence with ASTM standards to evaluate the ultimate tensile strength, dimensional accuracy, wear characteristics, and surface roughness. The findings from these assessments were systematically compared to the wear properties and mechanical behavior of PLA composites reinforced with boron nitride and the unreinforced PLA material. This study serves as a foundational resource that offers insights into the feasibility and methodologies of incorporating boron nitride into PLA matrices, paving the way for enhanced polymer composite development.

Processing of membranes and 3D scaffolds based on n-TiO2 colloidally dispersed on a thermoplastic matrix for photocatalytic pollutant removal

One of the most promising technologies for water treatment today is photocatalytic membrane reactors (PMRs). Manufacturing efficient membranes is still challenging as many factors are involved, like the porosity, specific surface area, nature and size of particles. In this work, a colloidal method to self-support commercial nanoparticles (n-TiO2) in a polymeric matrix of polylactic acid (PLA) is proposed allowing the fabrication of 2D and 3D structures with high inorganic content that can be adapted to the PMR configurations. Using a commercial filament of PLA loaded with up to 15 vol% of n-TiO2 as starting point, photocatalytic membranes have been manufactured by FFF. In addition, following a similar process, tapes with n-TiO2 particles up to 15 vol% have been processed by tape casting. Thermal characterisation (DTA) and dynamic rheometry evaluated the commercial filament for printing to determine the conditions used during the thermal extrusion and printing processes. FTIR and XRD technologies were used to determine the chemical interactions of PLA matrices with TiO2 nanoparticles. Porosity was measured by Archimedes's method for the filaments, by mercury intrusion for the membranes and by optical microscopy for the scaffolds. Finally, the microstructure of the 2D and 3D pieces was evaluated by scanning microscopy. 2D tape cast membranes were compared with individual filaments and 3D printed scaffolds in linear and gyroidal geometries. The catalytic activity results indicate that tape cast membranes show much higher kinetic constants than the individual filaments and the linear and gyroidal scaffolds. Regarding the two different printed scaffolds, in contrast to the kinetic values, gyroidal geometries achieve an average degradation time (t50) of 6.1 h, which is a lower value than those observed for linear scaffold geometries. Methyl orange degradation tests after 24 h exposure under UV light showed degradation rates of 98% for membranes, 90% for commercial filaments, 80% for gyroidal scaffolds and 60% for linear patterns. Therefore, these results are promising as a solution for fabricating easily extractable self-supported membranes for water treatment in PMRs.

Biochar filler in MEX and VPP additive manufacturing: characterization and reinforcement effects in polylactic acid and standard grade resin matrices

The development of sustainable and functional biocomposites remains a robust research and industrial claim. Herein, the efficiency of using eco-friendly biochar as reinforcement in Additive Manufacturing (AM) was investigated. Two AM technologies were applied, i.e., vat photopolymerization (VPP) and material extrusion (MEX). A standard-grade resin in VPP and the also eco-friendly biodegradable Polylactic Acid (PLA) in the MEX process were selected as polymeric matrices. Biochar was prepared in the study from olive trees. Composites were developed for both 3D printing processes at different biochar loadings. Samples were 3D-printed and mechanically tested after international test standards. Thermogravimetric Analysis and Raman revealed the thermal and structural characteristics of the composites. Morphological and fractographic features were derived, among others, with Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). Biochar was proven to be sufficient reinforcement agent, especially in the filament MEX process, reaching more than 20% improvement at 4 wt.% loading in tensile strength compared to the pure PLA control samples. In the VPP process, results were not as satisfactory, still, a 5% improvement was achieved in the flexural strength with 0.5 wt.% biochar loading. The findings prove the strong potential of biochar-based composites in AM applications, too.Graphical

The Effect of Nano Zirconium Dioxide (ZrO2)-Optimized Content in Polyamide 12 (PA12) and Polylactic Acid (PLA) Matrices on Their Thermomechanical Response in 3D Printing.

The influence of nanoparticles (NPs) in zirconium oxide (ZrO2) as a strengthening factor of Polylactic Acid (PLA) and Polyamide 12 (PA12) thermoplastics in material extrusion (MEX) additive manufacturing (AM) is reported herein for the first time. Using a melt-mixing compounding method, zirconium dioxide nanoparticles were added at four distinct filler loadings. Additionally, 3D-printed samples were carefully examined for their material performance in various standardized tests. The unfilled polymers were the control samples. The nature of the materials was demonstrated by Raman spectroscopy and thermogravimetric studies. Atomic Force Microscopy and Scanning Electron Microscopy were used to comprehensively analyze their morphological characteristics. Zirconium dioxide NPs showed an affirmative reinforcement tool at all filler concentrations, while the optimized material was calculated with loading in the range of 1.0-3.0 wt.% (3.0 wt.% for PA12, 47.7% increase in strength; 1.0 wt.% for PLA, 20.1% increase in strength). PA12 and PLA polymers with zirconium dioxide in the form of nanocomposite filaments for 3D printing applications could be used in implementations using thermoplastic materials in engineering structures with improved mechanical behavior.

Bacterial Response to the Surface Aging of PLA Matrices Loaded with Active Compounds.

The use of active components in biomaterials improves the properties of existing ones and makes it possible to obtain new devices with antibacterial properties that prevent infections after implantation, thus guaranteeing the success of the implant. In this work, cetyltrimethylammonium bromide (CTAB) and magnesium particles were incorporated into polylactic acid (PLA) films to assess the extent to which progressive aging of the new surfaces resists bacterial colonization processes. For this purpose, the films' surface was characterized by contact angle measurements, ToF-SIMS and AFM, and adhesion, viability and biofilm growth of Staphylococcus epidermidis bacteria on these films were also evaluated. The results show that the inclusion of Mg and CTAB in PLA films changes their surface properties both before and after aging and also modifies bacterial adhesion on the polymer. Complete bactericidal activity is exhibited on non-degraded films and films with CTAB. This antibacterial behavior is maintained after degradation for three months in the case of films containing a higher amount of CTAB.

Facile dispersion strategy to prepare polylactic acid/reed straw nanofiber composites with enhanced mechanical and thermal properties

The challenge of dispersing nanocellulose in hydrophobic polymers such as polylactic acid (PLA) still obstacles the further application of cellulose nanocomposites. An environment-friendly and facile wet-shearing pretreatment strategy without using any organic solvent was developed in this work. Silane modified lignocellulose nanofiber (SLCNF) was pre-dispersed into PLA by wet-shearing pretreatment, followed by extrusion process and the SLCNF could be dispersed extremely well in PLA matrices. SLCNF formed a crosslinked network and had an improved compatibility, which improved the mechanical and thermal properties of PLA composites. The tensile strength, elongation at break and thermal deformation temperature of the composites were increased by 12.6 %, 32.4 % and 9.1 °C, respectively. Moreover, SLCNF promoted the crystallization of PLA as a heterogeneous nucleating agent and the crystallinity was increased by about 40 %. This study provides an effective way to disperse nanocellulose in polymer matrix with high efficiency to enhance polymer-based composites.

Antibacterial and degradable properties of β-cyclodextrin-TiO2 cellulose acetate and polylactic acid bionanocomposites for food packaging

Polylactic acid (PLA) and cellulose acetate (CA) as biodegradable polymers are being highly exploited in the development of innovative materials across several industrial sectors. PLA and CA composite films with TiO2 nanoparticles (NPs) and β-cyclodextrin grafted TiO2 NPs were prepared. Thermo- and photo-degradation studies were performed on PLA and CA films and noticed that higher amount of TiO2 induce greater color variations, structure modifications and weight losses. It has been observed 9.3 % and 5.1 % maximum weight loss for 5 % TiO2 CA and PLA matrices, respectively. βCD-modified TiO2 NPs increased the photo-degradation of the plain polymers to a lesser extent than TiO2 NPs. Benzoic acid (BA) and sorbic acid (SA) were incorporated to βCD-TiO2 NPs and the antibacterial activity of PLA and CA composite films was studied by inactivation of Escherichia coli and Staphylococcus aureus. CA film filled with 5 % TiO2 NPs presented the highest antibacterial activity and achieved 71 % inhibition of E. coli and 88 % inhibition of S. aureus. CA composite films showed potential to be used as antimicrobial food packaging.

Atomic Scale Investigation on the Structural and Mechanical Properties of Carbon Nanotubes Reinforced Polylactic acid Composites

AbstractMolecular characterization of nanocomposites is of great significance for the design, prediction, and understanding of the structure and properties of nanocomposites. Herein, a molecular dynamics simulation method is employed to investigate the structures, thermodynamical, and mechanical properties of carbon nanotubes (CNTs) reinforced polylactic acid (PLA) composites, as well as the effects and mechanisms of CNTs on the structure and mechanical properties of PLA matrices. The concentration profile result suggests that the type of CNTs has a significant influence on the distribution of PLA molecular chains, with relative concentration profiles around CNTs in the order of PLA/CNTs‐COOH > PLA/CNTs‐OH > PLA/CNTs‐NH2 > PLA/CNTs. Incorporating CNTs into the PLA matrix decreases the FFV and mobility of the polymer, where the trend is PLA > PLA/CNTs > PLA/CNTs‐NH2 > PLA/CNTs‐OH > PLA/CNTs‐COOH. Meanwhile, the tensile properties of the PLA matrix increase with the incorporation of CNTs, and the trend agrees with the results of fractional free volume (FFV) and relative concentration distribution. Finally, the analysis results of interaction illustrate that hydrogen bond interactions between PLA molecular chains and the functional groups on CNTs surface are involved in the adsorption of the polymers on the CNTs surface, thus affecting their interfacial interaction, structure, and properties.

Ultra-fast laser modification of poly-lactic acid (PLA) -towards enhanced biocompatibility

In this study, the interaction was investigated of femtosecond laser radiation (pulse duration τ = 130 fs, wavelength λ = 800 nm) with poly-lactic acid (PLA) 2D scaffolds. Two sets of laser fluences (F) and scanning speed (V) values were applied to PLA matrices -F = 1.66 J/cm2, V = 3.8 mm/s, and F = 0.83 J/cm2, V = 3.8 mm/s. The PLA samples thickness, roughness, and water contact angle (WCA) were characterized before and after the laser structuring. The fs-induced micro structures were investigated by SEM, EDX, and FTIR analyses. Preliminary cell fibroblast studies were performed. The results obtained clearly show that a precise laser surface structuring could orient the cells matrix ingrowth and thus make PLA bone tissue engineering interbody future application more successful and adaptable to the personal needs of the recipients.

Entrapment of Phenylalanine Ammonia-Lyase in Nanofibrous Polylactic Acid Matrices by Emulsion Electrospinning

Immobilization of the recombinant, plant-derived Petroselinum crispum phenylalanine ammonia lyase (PcPAL) in electrospun matrices have the potential to create promising, easy-to-use biocatalysts. Polylactic acid (PLA) a biologically inert, commercial biopolymer, was chosen as the material of the carrier system. PLA could be electrospun properly only from water-immiscible organic solvents, which limits its application as a carrier of sensitive biological objects. The emulsion electrospinning is a proper solution to overcome this issue using non-ionic emulsifiers with different hydrophilic-lipophilic balance (HLB) values. The stabilized emulsion could protect the sensitive PcPAL dissolved in the aqueous buffer phase and improve fiber formation, plus help to keep the biocatalytic activity of enzymes. In this study, the first approach is described to produce PLA nanofibers containing PcPAL enzymes by emulsion electrospinning and to use the resulted biocatalyst in the ammonia elimination reaction from l-phenylalanine.

Effect of the raster orientation on strength of the continuous fiber reinforced PVDF/PLA composites, fabricated by hand-layup and fused deposition modeling

This paper presents the fabrication of a new class of high-porous composites made of polylactic acid (PLA) matrix reinforced with polyvinylidenfluorid (PVDF) long fibers. The composites were produced by printing the PLA matrix by using Fused Deposition Modeling (FDM) and adding continuous PVDF fibers by hand-layup. Materials properties were investigated, including the influence of two raster orientations during 3D printing ([0, 90] and [−45, +45]), by tensile and three-point bending tests. Experiments revealed that PVDF fibers within PLA matrices modified the composites behaviour providing higher ductility, whilst flexural strength decreased. Observation of the fracture surfaces showed that cracks followed the raster orientation lines avoiding a complete failure of the material structures and fibers (whereas unreinforced pure PLA samples fully broke). Composite configuration with [−45, +45] raster orientation exhibited higher strength and stiffness in comparison to the [0, 90] orientation, both in tensile and flexural conditions. Tensile failure was dominant in [−45, +45], and less influential in [0, 90]. Numerical models were also developed and compared. Two alternative approaches were considered in material modeling: Mori – Tanaka and ‘two-material’ models. No relevant differences emerged and a good agreement with experiments was achieved.

Liquid Crystal Display (LCD) and Organic Light Emitting Diode (OLED) Applications on Natural Fibre Reinforced Polymer Matrix Composites

Natural materials are the alternative source for the manufacture of products due to environmental requirements. Hot injection moulding techniques make the composite product with fibreglass, granite waste filler, and polylactic acid (PLA). Five samples of each set and sampled with better hardness varied the volumetric percentage of glass fibre and the waste nanogranite particles. This effort is mainly concerned with evaluating the wear of dry sliding and friction of composites. Varying 15, 25, 35, and 45 N load, 750 and 1500 m sliding distance tested the composite materials, respectively. Parametric condition experiments were carried out at the stated process to record answers. Nanogranite composite materials are better than higher concentrations of glass fibre in PLA matrices composites, which are more resistant to wear and friction coefficients. The nanogranite powder is added with the filler element in the PLA matrix to provide a better coefficient of wear and rubbing. A high load of 45 N and a sliding distance of 1500 m were measured at low wear and low friction coefficients.