Poly 4-vinylpyridine Research Articles

Continuous Flow Chemistry and Bayesian Optimization for Polymer-Functionalized Carbon Nanotube-Based Chemiresistive Methane Sensors.

We report the preparation of poly(ionic) polymer-wrapped single-walled carbon nanotube dispersions for chemiresistive methane (CH4) sensors with improved humidity tolerance. Single-walled CNTs (SWCNTs) were noncovalently functionalized by poly(4-vinylpyridine) (P4VP) with varied amounts of a poly(ethylene glycol) (PEG) moiety bearing a Br and terminal azide group (Br-R1). The quaternization of P4VP with Br-R1 was performed using continuous flow chemistry and Bayesian optimization-guided reaction selection. Polymers (PyBrR1) with different degrees of functionalization were used to disperse SWCNTs and subsequently incorporated into sensors containing a platinum complex as an aerobic oxidative catalyst with a polyoxometalate (POM) redox mediator to facilitate room-temperature CH4 sensing. As the degree of quaternization in the PyBrR1-CNT composites increased, improvements in response magnitude were observed, with nominally 10% quaternized PyBrR1 giving the largest response. Incorporation of PEG improved sensor stability at relative humidities between 57-90% versus sensors fabricated from CNT dispersions with unfunctionalized P4VP. Devices fabricated with these dispersions outperformed those prepared in situ under dry conditions, and exhibited greater stability at elevated humidities. The influence of Keggin-type POM character was also evaluated to identify alternative POMs for enhanced sensor performance at high humidity. In an effort to identify areas for further improvement in algorithm performance for polymer functionalization, a kinetically informed machine learning model was explored as a route to predict reactivity of pyridine units and alkyl bromides under flow conditions.

A pH-responsive phase-transition bi-affinity nanopolymer-assisted exosome metabolomics for early screening of osteoarthritis

Exosomes, emerging as ideal non-invasive biomarkers for disease diagnosis and monitoring, have seldom been explored based on metabolite levels. In this study, we designed and synthesized a pH-responsive phase-transition bifunctional affinity nanopolymer (pH-BiAN) that could efficiently and homogeneously separate exosomes from urine. Specifically, poly-4-vinylpyridine (P4VP) was chosen as the pH-responsive polymer and simultaneously modified with two exosome-affinity components CD63 aptamer and distearoyl phosphoethanolamine (DSPE) through a one-step amide reaction at room temperature. By utilizing two distinct but synergistic affinity mechanisms—the immune affinity between CD63 aptamer and exosomal CD63 proteins, and hydrophobic interactions between the DSPE and the exosomal lipids—pH-BiAN can enable efficient and specific exosome separation. Moreover, during the urine exosome capture procedure, the pH-BiAN outperforms conventional solid exosome separation materials by remaining soluble in the urine sample, significantly enhancing mass transfer and contact efficiency. After exosome capture, pH-BiAN can quickly aggregate and convert to solid upon pH adjustment, allowing for easy centrifugation separation. Afterwards, multiple machine learning models were established by combining liquid chromatography-mass spectrometry/mass spectrometry (LC-MS/MS) untargeted metabolomics for isolated exosomes, and the clinical accuracy of the training and test sets was more than 0.919, which could well distinguish early osteoarthritis patients from healthy people.

Synthesis of (-)-Cannabidiol (CBD), (-)-Δ9- and (-)-Δ8-Tetrahydrocannabinols, Encapsulation of CBD with Nanoparticles for Controlled Delivery and Biological Evaluation.

Cannabidiol (CBD) is garnering increasing interest due to its significant biological activity. This natural compound is one of the major cannabinoids in Cannabis sativa L. In this work, we describe the encapsulation of CBD in solid and hollow pH-sensitive poly(4-vinylpyridine) (solid@p4VP and hollow@p4VP) nanoparticles, and temperature-sensitive poly(N-isopropylacrylamide) (solid@pNIPAM and hollow@pNIPAM) nanoparticles for transport and release CBD in a controlled manner. The CBD loading into these smart polymeric systems was effective and their release profiles, solubility and resistance to stomach and intestinal conditions were evaluated, showing satisfactory properties and improved bioavailability with respect to free CBD. Finally, the A549 human lung cancer cell line was used as lung adenocarcinoma epithelial cellular model to carry out preliminary assays of the in vitro activity of the vehiculized CBD. For all these studies, synthetic CBD was employed, for which a new efficient and scalable synthesis of cannabinoids has been developed.

Experimental and computational analysis of poly(4-vinyl pyridine) and polyvinylpyrrolidone as effective corrosion inhibitors for low carbon steel in sulfuric acid

This study investigates the inhibitory effects of poly(4-vinyl pyridine) (P4VP) and polyvinylpyrrolidone (PVP) on the corrosion of low carbon steel (LCSt) in 1 M H2SO4. Protection efficacy (%PE) was measured using mass loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS). Results showed %PE values increased with higher polymer concentration and lower temperature. At 450 mg/L, %PE reached 93.13% and 94.19% for P4VP and PVP, respectively. These polymers function as mixed inhibitors, adsorbing onto the LCSt surface per Langmuir’s model as a mode of physical adsorption. EIS indicated that higher polymer concentration increased charge transfer resistance and decreased effective double-layer capacitance. Both P4VP and PVP also reduced pitting corrosion in chloride-containing solutions. Density Functional Theory (DFT) and Time-Dependent DFT (TD-DFT) optimized the molecular structures of the inhibitors, evaluating electronic parameters such as frontier molecular orbital (FMO) energies, energy gap, softness, hardness, electron transfer fraction, dipole moment, and hyperpolarizability ( β ° ). Monte Carlo (MC) and molecular dynamics (MD) simulations provided insights into adsorption mechanisms, corroborating experimental findings and highlighting the effect of protonation. This comprehensive study enhances our understanding of the relationship between molecular structure and function in polymer inhibitors, improving their application in corrosion protection.

Highly Asymmetric Lamellar Structure in Blends of Polystyrene-b-Poly(acrylic acid) Block Copolymers and Poly(4-vinylpyridine) Homopolymers Facilitated by Polyelectrolyte Complexation

Highly Asymmetric Lamellar Structure in Blends of Polystyrene-<i>b</i>-Poly(acrylic acid) Block Copolymers and Poly(4-vinylpyridine) Homopolymers Facilitated by Polyelectrolyte Complexation

Dual-Hydrogen Bond Donor-Functionalized Carbon Nanotube Fibers: Enhancing Anion-Sensing Performance Through Functionalization Approaches.

In this study, chemiresistive anion sensors are developed using carbon nanotube fibers (CNTFs) functionalized with squaramide-based dual-hydrogen bond donors (SQ1 and SQ2) and systematically compared the sensing properties attained by two different functionalization methods. Model structures of the selectors are synthesized based on a squaramide motif incorporating an electron-withdrawing group. Anion-binding studies of SQ1 and SQ2 are conducted using UV-vis titrations to elucidate the anion-binding properties of the selectors. These studies revealed that the chemical interaction with acetate (AcO-) induced the deprotonation of both SQ1 and SQ2. Selectors are functionalized onto the CNTFs using either covalent or non-covalent functionalization. For covalent functionalization, SQ1 is chemically formed on the surface of the CNTFs, whereas SQ2 is non-covalently functionalized to the surface of the CNTFs assisted by poly(4-vinylpyridine). The results showed that non-covalently functionalized CNTFs exhibited a 3.6-fold higher sensor response toward 33.33mm AcO- than covalently functionalized CNTFs. The selector library is expanded using diverse selectors, such as TU- and CA-based selectors, which are non-covalently functionalized on CNTFs and presented selective AcO--sensing properties. To demonstrate on-site and real-time anion detection, anion sensors are integrated into a sensor module that transferred the sensor resistance to a smartphone via wireless communication.

INVESTIGATION OF THE EFFICIENCY OF RHENIUM ION SORPTION USING ION-EXCHANGE RESINS POLYACRYLIC ACID: POLY-4-VINYLPYRIDINE IN VARIOUS RATIOS

This study is devoted to the study of the efficiency of sorption of rhenium ions using ion-exchange resins containing polyacrylic acid (PAK) and poly-4-vinylpyridine (P4VP) in various composition ratios. Goals and objectives. To investigate synthesized resins with different ratios of PAK:P4VP and to study their sorption capacity, kinetics and selectivity with respect to rhenium ions. Methods. Thanks to a comprehensive experimental analysis, including periodic sorption experiments and characterization methods such as spectrophotometry and atomic emission spectroscopy, the effect of resin composition on sorption efficiency was clarified during the study. Results and discussion. Optimal ratios have been determined to ensure maximum efficiency of rhenium ion removal. In addition, the study examines the main mechanisms governing sorption properties, with an emphasis on the relationship between resin composition, surface chemical composition and ion interaction. Conclusion. The results obtained contribute not only to the development of special ion-exchange materials for the effective extraction and purification of rhenium, but also contribute to a deeper understanding of ion sorption processes. This research has important implications for rhenium-dependent industries, offering strategies for solving problems related to its extraction, purification and use.

Ultrafine copper oxide nanoparticles immobilized on poly (4-vinylpyridine)-grafted UiO-66-NH2 as heterogeneous catalyst for oxidative homocoupling of terminal alkynes

Terminal alkyne homocoupling is an effective route to synthesize 1,3-diynes, which are crucial components of many fine chemicals and natural products. However, the reaction often faces challenges of catalyst recovery and typically necessitates the introduction of basic additives, which limits its practical applicability. Here, we have developed a green and efficient Cu2O@UiO-66-g-P4VP nanocatalyst that exhibits outstanding activity for homocoupling terminal alkynes under mild, base- or ligand-free conditions. The characterization results indicate that the nitrogen atoms in P4VP interfere with the electronic structure of Cu in Cu2O nanoparticles, causing the N electrons to shift onto Cu. Density functional theory (DFT) calculations suggest that this catalytic system facilitates the activation of oxygen on the copper surface, promoting the coupling reaction. This work provides a feasible strategy for the rational fabrication of MOF-supported polybase and Cu2O nanocrystals as heterogeneous nanocatalysts in the oxidative homocoupling of alkynes.

Individual cell modification with cell surface specific atom transfer radical polymerization for enhanced Cr(VI) removal

Modifying cells with polymers on the surface can enable them to gain or enhance function with various applications, wherein the atom transfer radical polymerization (ATRP) has garnered significant potential due to its biocompatibility. However, specifically initiating ATRP from the cell surface for in-situ modification remains challenging. This study established a bacterial surface-initiated ATRP method and further applied it for enhanced Cr(VI) removal. The cell surface specificity was facilely achieved by cell surface labelling with azide substrates, following alkynyl ATRP initiator specifically anchoring with azide-alkyne click chemistry. Then, the ATRP polymerization was initiated from the cell surface, and different polymers were successfully applied to in-situ modification. Further analysis revealed that the modification of Shewanella oneidensis with poly (4-vinyl pyridine) and sodium polymethacrylate improved the heavy metal tolerance and enhanced the Cr(VI) removal rate of 2.6 times from 0.088h-1 to 0.314h-1. This work provided a novel idea for bacterial surface modification and would extend the application of ATRP in bioremediation.

Improved Interfacial Electron Dynamics with Block Poly(4-vinylpyridine)-Poly(styrene) Polymers for Efficient and Long-Lasting Dye-Sensitized Solar Cells.

Dye-sensitized solar cells (DSSCs) have recently entered the market for indoor photovoltaics. Fast electron injection from dye to titania, the lifetime of the excited dye, and the suppression of back electron recombination at the photoanode/electrolyte interface are crucial for a high photocurrent conversion efficiency (PCE). This study presents block copolymers of poly(4-vinylpyridine) and poly(styrene)-P4VP67-b-PSt x(x=23;61) as efficient accelerators of electron injection from dye to titania with extended lifetime excited states and long-lasting back electron recombination suppression. P4VP67-b-PSt23 and P4VP67-b-PSt61 rendered devices with PCEs of 10.0 and 9.8%, respectively, under AM 1.5G light; PCEs of 19.4 and 16.4% under 1000 lx LED light were attained. Copolymers provided a stable PCE with the two most popular I3 -/3I- electrolytes based on ACN and 3-methoxypropionitrile solvents; PCE history was tracked in the dark and under 1000 h of continuous light soaking with passive load according to ISOS-D1 and ISOS-L2 aging protocols, respectively. The impact of the polymer molecular structure on electron recombination, charge injection, dye anchoring, light absorption, photocurrent generation, and PCE and the long-term history of photovoltaic metrics are discussed.

Electron Transporting Polymeric Materials with Partial Quaternization for High-Performance Organic Solar Cells.

Efficient cathode interfacial layers (CILs) have become a crucial component of organic solar cells (OSCs). Charge extraction barriers, interfacial trap states, and significant transport resistance may be induced due to the unfavorable cathode interlayer, limiting the device performance. In this study, poly(4-vinylpyridine) is used as the CIL for OSCs, and a new type of CIL named P4VP-I is synthesized through the quaternization strategy. Compared to P4VP, P4VP-I CIL exhibits enhanced conductivity and optimized work function. OSCs employing the P4VP-I ETL demonstrate prolonged carrier lifetime, suppressed charge recombination, and achieve higher power conversion efficiencies (PCE) than the commonly used ETLs such as PFN-Br and Phen-NaDPO.

(Invited) Multiplexed CRISPR-Based ECL Assay for Alzheimer’s Biomarkers

Currently, more than 6 million Americans live with Alzheimer’s disease (AD), and it is projected to be 13 million by 2050. AD has no permanent cure yet, and early detection is important to slow down the progress of the disease. Diagnosis is complicated by AD’s similarity to other geriatric diseases. Beta-amyloid peptide (Aβ42), tau proteins and neurofilament light (NFL) measured in the cerebrospinal fluid (CSF) is a reasonably effective method for diagnostics, but very painful for the patients. MicroRNA’s (miRNAs) expressed in the brain are promising biomarkers and our goal of this study is to develop a sensitive and selective point-of-care (POC) test to detect AD specific miRNA (miRNA 30e, 34c and 200c) based on the CRISPR-Cas system. The Cas 13a protein has the regular sequence specific RNase activity followed by a collateral RNase activity. We used this feature of Cas 13a to generate an electrochemiluminescence (ECL) signal by binding specific miRNA biomarkers, and then collaterally cleaving poly-ribose guanine (poly-rG). This cleaved strands of poly-rG and rG itself are coreactants for ECL, and react with ECL polymer Ruthenium Polyvinyl Pyridine (RuPVP) to generate ECL. RuPVP is deposited into pyrolytic graphite (PG) micro wells. Using a 3D-printed microfluidic device equipped with the Pt reference and Ag/AgCl counter electrodes, patient serum mixed with poly-rG is introduced to the RuPVP coated electrode at 1.3 V to provide ECL light measured by a CCD camera. The assay was multiplexed to detect 3 AD specific miRNAs, and obtain a separate calibration for each miRNA biomarker with linear ranges from 70 pg/ mL to 7 µg/mL, from 7.4 pg/ mL to 74 µg/ mL and from 7.4 fg/ mL to 74 µg/ mL for 30e, 34c and 200c respectively. Preliminary LODs were 42 pg/ mL, 0.074 fg/ mL and 0.15 fg/ mL for miRNA 30e, 34c and 200c respectively. Results confirm the sensitivity of the assay. Further, spike recovery, cross reactivity studies and patient sample assays will be reported.

Interphase-Controlled Inkjet Printing of MicroInlaid OLEDs: Effects of Solvent- and Solute-Polymer Interactions.

Inkjet printing, a highly promising technique for the cost-effective fabrication of large-scale organic light-emitting devices (OLEDs), typically necessitates the intricate alignment of precisely patterned insulating layers. Recently, we introduced a unique single-step inkjet printing process that produces well-patterned microinlaid spots of functional compounds through insulating polymer layers. This approach exploits lateral phase separation between the solute of functional compounds and the polymer, allowing the simultaneous spatial etching of the polymer and the infilling of the solute using a single inkjet-printed sessile droplet. Here, we demonstrate that the interaction between the solvent and polymer, as well as the solute and polymer, critically determines the precision and efficiency of printing. This is particularly evident when using either the insulating poly(vinylpyridine) isomer of poly(4-vinylpyridine) (P4VP) or poly(2-vinylpyridine) (P2VP) with chloroform as a solvent, which allows for a detailed examination of these interactions based on certain solubility parameters. Micro-Raman spectroscopy reveals that the self-organizing capability of the microinlaid spots with P4VP is superior to that with P2VP. This is due to the fact that P2VP shows higher affinity to the solvent and causes imperfect phase separation as compared to P4VP. As a result, a performance evaluation demonstrates enhanced device performance for inkjet-printed green micro-OLEDs with P4VP, exhibiting a higher external quantum efficiency of 3.3% compared to that of 2.3% achieved with P2VP. These findings elucidate the important roles of solvent-polymer and solute-polymer interactions in the inkjet printing process, leading to interfacial control of inkjet printing technique for the cost-effective production of high-performance and high-resolution micro-OLEDs.

Synthesis of Metallic and Metal Oxide Nanoparticles Using Homopolymers as Solid Templates: Luminescent Properties of the Eu+3 Nanoparticle Products

Starting from poly(4-vinylpyridine) ((P4VP)n), poly(2-vinylpyridine) ((P2VP)n), and [N=P(O2CH2CF3)]m-b-P2VP20 block copolymers, a series of metal-containing homopolymers, (P4VP)n⊕MXm, (P2VP)n⊕MXm, and [N=P(O2CH2CF3)]m-b-P2VP20]⊕MXm MXm = PtCl2, ZnCl2, and Eu(NO3)3, have been successfully prepared by using a direct and simple solution methodology. Solid-state pyrolysis of the prepared metal-containing polymeric precursors led to the formation of a variety of different metallic and metal oxide nanoparticles (Pt, ZnO, Eu2O3, and EuPO4) depending on the composition and nature of the polymeric template precursor. Thus, whereas Eu2O3 nanostructures were obtained from europium-containing homopolymers ((P4VP)n⊕MXm and (P2VP)n⊕MXm), EuPO4 nanostructures were achieved using phosphorus-containing block copolymer precursors, [N=P(O2CH2CF3)]m-b-P2VP20]⊕MXm with MXm = Eu(NO3)3. Importantly, and although both Eu2O3 and EuPO4 nanostructures exhibited a strong luminescence emission, these were strongly influenced by the nature and composition of the macromolecular metal-containing polymer template. Thus, for P2VP europium-containing homopolymers ((P4VP)n⊕MXm and (P2VP)n⊕MXm), the highest emission intensity corresponded to the lowest-molecular-weight homopolymer template, [P4VP(Eu(NO3)3]6000, whereas the opposite behavior was observed when block copolymer precursors, [N=P(O2CH2CF3)]m-b-P2VP20]⊕MXm MXm= Eu(NO3)3, were used (highest emission intensity corresponded to [N=P(O2CH2CF3)]100-b-[P2VP(Eu(NO3)3)x]20). The intensity ratio of the emission transitions: 5D0 → 7F2/5D0 → 7F1, suggested a different symmetry around the Eu3+ ions depending on the nature of the polymeric precursor, which also influenced the sizes of the prepared Pt°, ZnO, Eu2O3, and EuPO4 nanostructures.

Poly(vinyl pyridine) coatings cross-linked with transition metal complexes as active layers for biosensors sensitive to protein adsorption and cell adhesion

The possibility of application of poly(4-vinyl pyridine) layers cross-linked with transition metal complexes as active layers in biomedical sensors was tested. The successful modification of the P4VP coating with CuBr2 or ZnBr2 was verified using time of flight - secondary ion mass spectrometry and X-ray photoelectron spectroscopy. The topography and wettability of the coatings were examined by using atomic force microscopy and water contact angles measurements, respectively. Tests of biological activity of coatings indicated strong protein adsorption, good biocompatibility, and no antimicrobial activity. The potential of the coatings to be used as active layers of biosensors was verified, by systematic impedance-based measurements, which showed the sensitivity of the P4VP:CuBr2 coatings to the presence of proteins and cells in different concentrations. The high selectivity of the coatings toward the defined analyte was confirmed by the specific antigen–antibody immunoreaction, and the possibility of in situ monitoring of protein adsorption and cell adhesion also for individual cells was presented. Finally, the conductive response of a bilayer system that mimics Organic Field Effect Transistor was shown. These results point to a great potential for both coatings to serve as active layers of sensitive and highly selective biosensors.

Isoporous Membranes by the Symmetric Triblock Copolymer: A Strategy to Improve the Mechanical Strength without Sharply Changing the Pore Size and Permselectivity.

Isoporous membranes produced from diblock copolymers commonly display a poor mechanical property that shows many negative impacts on their separation application. It is theoretically predicted that dense films produced from symmetric triblock copolymers show much stronger mechanical properties than those of homologous diblock copolymers. However, to the best of our knowledge, symmetric triblock copolymers have rarely been fabricated into isoporous membranes before, and a full understanding of separation as well as mechanical properties of membranes prepared from triblock copolymers and homologous diblock copolymers has not been conducted, either. In this work, a cleavable symmetric triblock copolymer with polystyrene as the side block and poly(4-vinylpyridine) (P4VP) as the middle block was synthesized and designed by the RAFT polymerization using the symmetric chain transfer agent, which located at the center of polymer chains and could be removed to produce homologous diblock copolymers with half-length while having the same composition as that found in triblock copolymers. The self-assembly of these two copolymers in thin films and casting solutions was first investigated, observing that they displayed similar self-organized structures under these two conditions. When fabricated into isoporous membranes, they showed similar pore sizes (5-7% difference) and comparable rejection performance (∼10% difference). However, isoporous membranes produced from triblock copolymers showed significantly improved mechanical strength and higher toughness (2-10 times larger) as evidenced by the compacting resistance, strain-stress determination, and nanoindentation testing, suggesting the unique and novel structure-performance relationship in the isoporous membranes produced from symmetric triblock copolymers. The above finding will guide the way to fabricate mechanically robust isoporous membranes without notably changing the separation performance from rarely used symmetric triblock copolymers, which can be synthesized by the controlled polymerization as facilely as that found for diblock copolymers.

Detecting Shape of Hybrid Polymer/Surfactant Micelles: Cryo-Transmission Electron Microscopy, Small-Angle Neutron Scattering and Dynamic Light Scattering Study

In-depth study of shape of hybrid micelles in the micellar solutions of anionic surfactant potassium oleate, containing hydrophobic polymer poly(4-vinylpyridine) (P4VP) was conducted via cryo-transmission electron microscopy (cryo-TEM), small-angle neutron scattering (SANS) and dynamic-light scattering of visible light (DLS). Direct visualization of the solutions with cryo-TEM evidenced the coexistence of polymer-free spherical micelles and branched rodlike hybrid micelles with mean length of 200 nm and radius of 2 nm, governed by contour length of solubilized P4VP and length of hydrophobic “tail” of potassium oleate, respectively. The formation of branches in the hybrid micelles was explained by attaching the thermodynamically unfavorable end-caps of micelles to their polymer-loaded cylindrical fragments. By SANS it was shown that the cylindrical local shape and the radius of the micelles are independent of the concentration of embedded P4VP. Relaxation processes in the solutions were investigated with DLS. Three relaxation modes were observed for hybrid micelles, similar to polymer-free wormlike micelles. Fast and medium relaxation modes were attributed to diffusion of entangled micellar chains and their segments, respectively. The slow mode was related to electrostatic repulsion between similarly charged hybrid micelles.

Effect of Salt Content on Solubilization of Hydrophobic Polymer by Wormlike Micelles of Ionic Surfactant

The effect of concentration of inorganic salt KCl on solubilization of hydrophobic polymer poly(4-vinylpyridine) (P4VP) in aqueous solutions of ionic surfactant potassium oleate was experimentally investigated. As was shown by rheology, in the range of concentrations from 1 to 5 wt.% of salt the polymer-free solutions of surfactant mainly contain linear wormlike micelles (WLMs). The formation of branched WLMs was observed in the solutions containing 5-9 wt.% of KCl. In the presence of higher salt content the phase separation occurred, indicating the formation of a highly branched saturated network of WLMs. Enhanced screening of the charged groups of potassium oleate by oppositely charged ions of KCl caused elongation and branching of micelles that reflected in zero-shear viscosity of the solutions passing through the maximum. In the phase diagram, the saturation concentration with P4VP of both linear and branched WLMs decreased with increasing salt content. In the case of linear WLMs, this could be explained by the constant number of embedded polymer chains per 1 WLM, while simultaneously decreasing number of WLMs in the system. As for the branched WLMs, it was caused by shortening of the linear parts of micelles due to the formation of branching points. For this reason, almost no P4VP was dissolved in the solution containing the highly branched saturated network.

Mitigating Cobalt Phthalocyanine Aggregation in Electrocatalyst Films through Codeposition with an Axially Coordinating Polymer.

Cobalt phthalocyanine (CoPc) is a promising molecular catalyst for aqueous electroreduction of CO2, but its catalytic activity is limited by aggregation at high loadings. Codeposition of CoPc onto electrode surfaces with the coordinating polymer poly(4-vinylpyridine) (P4VP) mitigates aggregation in addition to providing other catalytic enhancements. Transmission and diffuse reflectance UV-vis measurements demonstrate that a combination of axial coordination and π-stacking effects from pyridyl moieties in P4VPserve to disperse cobalt phthalocyanine in deposition solutions and help prevent reaggregation in deposited films. Polymers lacking axial coordination, such as Nafion, are significantly less effective at cobalt phthalocyanine dispersion in both the deposition solution and in the deposited films. SEM images corroborate these findings through particle counts and morphological analysis. Electrochemical measurements show that CoPc codeposited with P4VPonto carbon electrode surfaces reduces CO2 with higher activity and selectivity compared to the catalyst codeposited with Nafion.

A snapshot review of the crystallization of polymer chains complexed by small molecules focusing on poly(4-vinylpyridine) systems: Opportunities and challenges

A snapshot review of the crystallization of polymer chains complexed by small molecules focusing on poly(4-vinylpyridine) systems: Opportunities and challenges