Plate Fixation Research Articles

Technique for traversing both plate and nail-locking screw holes in nail-plate composite fixation.

Technique for traversing both plate and nail-locking screw holes in nail-plate composite fixation.

Locking vs. non-locking plate fixation in comminuted talar neck fractures: a biomechanical study using cadaveric specimens

BackgroundTalar neck fractures are rare but potentially devastating injuries, with early reduction and rigid fixation essential to facilitate union and prevent avascular necrosis. Even small degrees of malunion will alter load transmission and subtalar joint kinematics. Changes in fixation techniques have led to dual plating strategies. While locked plating has perceived advantages in porotic bone and comminution, its biomechanical benefits in talar neck fractures have not been shown. AimTo compare the strength of locking vs. non-locking plate fixation in comminuted talar neck fractures. MethodSeven pairs of cadaveric tali were randomised to locking or non-locking plate fixation. A standardised model of talar neck fracture with medial comminution was created, and fixation performed. The fixed specimens were mounted onto a motorised testing device, and an axial load applied. ResultsPeak load to failure, deformation at failure, work done to achieve failure, and stiffness of the constructs were measured. No statistically significant difference was found between locking and non-locking constructs for all parameters. ConclusionsBoth constructs provide similar strength to failure in talar neck fracture fixations. Mean peak load to failure did not exceed the theoretical maximum forces generated of 1.1 kN when weight-bearing. We would advocate caution with early mobilisation in both fixations.

Evaluation of functional outcome in patients treated with locking compression plate for distal femur fractures

Distal femur fractures are always a challenge to an orthopedic surgeon. They may be unstable and comminuted. Thin cortex, wide medullary canal, relative osteopenia and short distal segment adds to the complexity. The present study assessed the functional outcome of using locking compression plate fixation for fractures of distal end of femur in patients admitted to JMMC orthopedics department satisfying the inclusion and exclusion criteria from December 2017 to may 2019. Twenty cases were taken in this study. Serial follow up was done at 4, 8, 12, 24 weeks and functional outcome was assessed at the end of 24 weeks using NEERS criteria. 18 patients were treated with open reduction and internal fixation. 2 of the fractures were stabilized via MIPPO technique. No patients had implant failure and none of the cases were complicated by deep infection. 5 of the 20 patients had ‘Excellent’ Neers scores and 14 had ‘Good’ scores. Only one patient had ‘Fair’ score.
 Conclusion: Locking compression plate fixation is a safe procedure for supracondylar fractures of distal femur with good functional outcome. It can be done on a routine basis with a minimum risk of complications.
 Keywords: Functional Outcome, LCP, Open Reduction Internal Fixation, Prospective Study, Supracondylar Fracture.

The effect of body weight on interfragmentary fracture strain in plate fixation of distal femur fractures: A finite element analysis

IntroductionDistal femur fractures are difficult to successfully treat due to high rates of nonunion. Obesity is an independent prognostic risk factor for nonunion. Advances in finite element analyses (FEAs) have allowed researchers to better understand the performance and behavior of constructs at the bone-implant interface under a variety of conditions. The purpose of this study is to determine the impact of body weight on fracture strain in a lateral locking plate construct for supracondylar femur fractures and whether additional construct rigidity is beneficial to optimize fracture strain in high body mass patients. HypothesisWe hypothesized that increased loads would produce a higher interfragmentary strain (IFS), which could be decreased by shortening the working length of the construct. Materials and methodsA 3D finite element analysis was performed on two separate femur models with a comminuted supracondylar distal femur fracture fixed with a lateral distal femoral locking plate in bridging mode with Ansys software. Axial forces were varied to recreate the effect of load from normal and high body mass patients. Working length and screw density of the construct were varied for each condition. Measurements of interfragmentary strain and shear motion (SM) were compared. ResultsDoubling the axial load from 70kg (control) to 140kg (high body mass) increased the interfragmentary strain by an average of 76% for the three working lengths (3.38%±1.67% to 4.37%±0.88% at the baseline working length (BWL), 1.42%±1.00% to 2.87%±2.02% at the intermediate working length (IWL) and 0.62%±0.22% to 1.22%±0.42% at the short working length (SWL)). On average, decreasing the working length in the 140kg load reduced the mean IFS to within 15% of the mean IFS of the 70kg load at the longer working length (2.87%±2.02% at IWL 140kg versus 3.38%±1.67% at BWL 70kg and 1.22%±0.45% SWL 140kg versus 1.42±1.00% IWL 70kg). DiscussionIncreased axial load increases interfragmentary strain in an AO/OTA 33A distal femur fracture fixed with a lateral distal femoral locking plate. Decreasing the working length of the fixation construct in the high body mass model decreased interfragmentary strain. Higher loading conditions reflective of high body mass patients should be considered in studies investigating optimization of fracture strain. Level of proofV; Finite Element Analysis (FEA).

Adjunctive dorsal spanning plate fixation for challenging distal radius injuries

BackgroundDistal radius fractures with severely osteoporotic bone or articular comminution can provide challenges to fixation with traditional volar locked plating alone. The purpose of this study was to evaluate the clinical, radiographic, and patient reported outcomes of patients undergoing distal radius fixation with volar locked plating and adjunctive dorsal bridge plating. MethodsWe retrospectively identified 16 patients with distal radius fractures who underwent our preferred surgical technique for fixation. Patients underwent volar locked plate fixation as well as dorsal bridge fixation at time of surgery. Seven patients were indicated for severe articular comminution with volar rim fragmentation (44%), three patients were revised for nonunion after previous volar locked late fixation (19%), and six patients had severely osteoporotic bone with articular comminution (38%). Two patients (13%) sustained AO/OTA 23-A3 distal radius fracture, two patients (13%) had a 23-B3 fracture, two patients (13%) had a 23-C2 fracture and ten patients (63%) had a 23-C3 fracture. ResultsThe average patient age was 51.8 years ± 20.6. Patients were followed for an average of 12.2±6.3 months. The dorsal bridge plate was removed at an average of 11.1±2.4 weeks. The average post-operative radial inclination was 18.9±2.4°, radial height 12.4 mm ± 2.6 mm, and volar tilt 7.1±1.9°. There were no cases of deep or superficial infection. After dorsal bridge plate removal, patients demonstrated an average wrist extension of 55.3±9.5°, flexion 54.4±12.8°, radial deviation 15.7±3.2°, 25.2±3.9 degrees of ulnar deviation. ConclusionDistal radius fractures in the setting of severely osteoporotic bone, salvage procedures, articular comminution, volar rim fractures, and revision surgery present uniquely difficult surgical challenges. Volar locked plating with adjunctive dorsal bridge plating can be used with good short- and long-term results.

“Does Hook Type Matter in Articular Distal Radius Fixation? Re. Does Construct Type Matter? A Retrospective Review Comparing Outcomes of Distal Radius Fractures Treated with Standard Volar Plating versus Fragment-specific Fixation”

“Does Hook Type Matter in Articular Distal Radius Fixation? Re. Does Construct Type Matter? A Retrospective Review Comparing Outcomes of Distal Radius Fractures Treated with Standard Volar Plating versus Fragment-specific Fixation”

Treatment of bilateral developmental dysplasia of the hip joint with an improved technique: A case report

BACKGROUND Developmental dysplasia of the hip (DDH) is a common osteoarticular deformity in pediatric orthopedics. A patient with bilateral DDH was diagnosed and treated using our improved technique "(powerful overturning acetabuloplasty)" combined with femoral rotational shortening osteotomy. CASE SUMMARY A 4-year-old girl who was diagnosed with bilateral DDH could not stand normally, and sought surgical treatment to solve the problem of double hip extension and standing. As this child had high dislocation of the hip joint and the acetabular index was high, we changed the traditional acetabuloplasty to "powerful turnover acetabuloplasty" combined with femoral rotation shortening osteotomy. During the short-term postoperative follow-up (1, 3, 6, 9, 12, and 15 months), the child had no discomfort in her lower limbs. After the braces and internal fixation plates were removed, formal rehabilitation training was actively carried out. CONCLUSION Our "powerful overturning acetabuloplasty" combined with femoral rotational shortening osteotomy is feasible in the treatment of DDH in children. This technology may be widely used in the clinic.

Design and Biomechanical Finite Element Analysis of Spatial Weaving Infracalcaneal Fixator System.

Traditional internal fixation of calcaneus fractures, involving lateral L-shaped incisions and plate fixation, has disadvantages such as increased operative exposure, eccentric plate fixation, and complications. The aim of this study was to design a Spatial Weaving Intra-calcaneal Fixator System (SWIFS) for the treatment of complex calcaneal fractures and to compare its biomechanical properties with those of traditional calcaneal plates. The computed tomography (CT) data of the normal adult calcaneus was used for modeling, and the largest trapezoidal column structure was cut and separated from the model and related parameters were measured. The SWIFS was designed within the target trapezoid, according to the characteristics of the fracture of the calcaneus. The Sanders model classification type IV calcaneal fracture was established in finite element software, and fixation with calcaneal plate and the SWIFS examined. Overall structural strength distribution and displacement in the two groups were compared. The maximum 3D trapezoidal column in the calcaneus was constructed, and the dimensions were measured. The SWIFS and the corresponding guide device were successfully designed. In the one-legged erect position state, the SWIFS group exhibited a peak von Mises equivalent stress of 96.00 MPa, a maximum displacement of 0.31 mm, and a structural stiffness of 2258.06 N/mm. The conventional calcaneal plate showed a peak von Mises equivalent stress of 228.66 Mpa, a maximum displacement of 1.26 mm, and a structural stiffness of 555.56 N/mm. The SWIFS group exhibited a 75.40% decrease in displacement and a 306.45% increase in stiffness. Compared with fixation by conventional calcaneal plate, the SWIFS provides better structural stability and effective stress distribution.

Teardrop Alignment Changes After Volar Locking Plate Fixation of Distal Radius Fractures With Volar Ulnar Fragments.

We assessed factors associated with change in radiographic teardrop angle following volar locking plate (VLP) fixation of volarly displaced intra-articular distal radius fractures with volar ulnar fragments (VUF) within the ICUC database. The primary outcome was change in radiographic alignment on follow-up imaging, defined as a change in teardrop angle from intra-operative fluoroscopy greater than 5°. Patients with distal radius fractures treated with a VLP within the ICUC database, an international collaborative and publicly available dataset, were identified. The primary outcome was volar rim loss of reduction on follow-up imaging, defined as a change in radiographic alignment from intra-operative fluoroscopy, teardrop angle less than 50°, or loss of normal radiocarpal alignment. Secondary outcomes were final range of motion (ROM) of the affected extremity. Radiographic Soong classification was used to grade plate position. Descriptive statistics were used to assess variables' distributions. A Random Forest supervised machine learning algorithm was used to classify variable importance for predicting the primary outcome. Traditional descriptive statistics were used to compare patient, fracture, and treatment characteristics with volar rim loss of reduction. Volar rim loss of reduction and final ROM in degrees and as compared with contralateral unaffected limb were also assessed. Fifty patients with volarly displaced, intra-articular distal radius fractures treated with a VLP were identified. Six patients were observed to have a volar rim loss of reduction, but none required reoperation. Volar ulnar fragment size, Soong grade 0, and postfixation axial plate position in relation to the sigmoid notch were significantly associated (P < .05) with volar rim loss of reduction. All cases of volar rim loss of reduction occurred when VUF was 10.8 mm or less. The size of the VUF was the most important variable for predicting volar rim loss of reduction followed by postfixation plate position in an axial position to the sigmoid notch and the number of volar fragments in the Random Forest machine learning algorithm. There were no significant differences in ROM between patients with volar ulnar escape and those without.

Talonavicular-cuneiform arthrodesis in the management of Mueller-Weiss Syndrome: a retrospective case series.

Mueller-Weiss Syndrome (MWS), characterized by spontaneous adult-onset tarsal navicular osteonecrosis, is an uncommon cause of chronic midfoot pain that can lead to functional impairment and progressive deformities. This study aimed to present clinical and radiological outcomes of talonavicular-cuneiform (TNC) arthrodesis in the treatment of patients with MWS. A retrospective study was performed on 8 consecutive patients (6 female, 2 male; mean age = 50 years; range = 33-64) who underwent TNC arthrodesis using plate fixation with autologous bone grafting for the treatment of MWS. To evaluate clinical status, the American Orthopaedic Foot and Ankle Society (AOFAS) Ankle-Midfoot Score was performed immediately preoperatively and at the final follow-up. In radiographic evaluation, talus-first metatarsal angle (Meary's angle) was measured preoperatively and at the final follow-up. Solid fusion was also examined on postoperative radiographs and computerised tomography. The mean follow-up was 35 months (range = 24-52). The mean AOFAS improved from 37 (range = 24-53) preoperatively to 85 (range = 80-93) at the final follow-up (p < 0.001). No major intra- operative complications were observed in any of the patients. According to the Maceira and Rochera radiological staging system, 5 feet was stage 3, and 3 feet was stage 4. The mean union time was 10 months (range = 5-15). Radiographic solid fusion was achieved in all but one foot that developed talonavicular non-union. TNC arthrodesis using plate fixation with autologous bone grafting seems to be an effective surgical method for reconstruction of MWS.

A single-centre retrospective 10-year experience of the rhombic 3D condylar fracture plate for open reduction and internal fixation of condylar neck and base fractures

Fractures of the mandibular condyle account for a significant proportion of mandibular fractures. The specific functional loads require particular specifications for the implant design used for open reduction and internal fixation of such fractures. The clinical and radiographic outcomes in patients treated using a single rhombic 3D condylar fracture plate for open reduction and internal fixation at a single institution, and who fulfilled the inclusion and exclusion criteria, are presented.The primary outcome variables were: occlusion, maximum interincisal distance and mandibular excursion at 1, 3, and 6 months postoperatively, and radiographic measurements for mandibular height and gonion angle.In total, 263 patients were included, of whom 173 (65.8%) were male and 90 (34.2%) female. The mean age was 40.4 ± 18.9 years. There was satisfactory occlusion in 98.9% of patients at the 6-month follow-up, and a significant improvement in all parameters for mandibular excursion (p < 0.001), with a reduced ramus height and an increase in the gonion angle on the fractured side.Excellent clinical and radiographic results were achieved using the rhombic-shaped implant, deeming it appropriate for the osteosynthesis of mandibular condyle fractures.

Non-unions and wound infections do not differ following intramedullary nailing and plate osteosynthesis for distal third femur fractures: a meta-analysis.

The fixation method of distal, extra-articular femur fractures is a controversially discussed. To ensure better stability itself, earlier mobilization and to prevent blood loss - all these are justifications for addressing the femur via reamed intramedullary nailing (RIMN). Anatomical reposition of multifragmentary fractures followed by increased risks of non-union are compelling reasons against it. The purpose of this study was to systematically review the literature for rates of non-union and wound infection, as well as blood loss and time of surgery. According to the PRISMA guidelines we conducted this systematic review by searching the Cochrane, PubMed, Ovid, MedLine, and Embase databases. Inclusion criteria were the modified Coleman methodology score (mCMS) >60, age >18 years, and extra-articular fractures of the distal femur. Biomechanical and animal studies were excluded. By referring to title and abstract relevant articles were reviewed independently. In the consecutive meta-analysis, we compared 9 studies and 639 patients. There is no statistically significant difference comparing superficial wound infections when RIMN was performed (OR = 0.50; 95% CI: 0.18 - 1.42; P = 0.19) as well as in deep wound infections (OR = 0.74; 95% CI: 0.19-2.81; P = 0.62). However, these results were not significant. We also calculated for potential differences in the rate of non-unions depending on the surgical treatment applied. Data of 556 patients revealed an overall number of 43 non-unions. There was no significant difference in rate of non-unions between both groups (OR = 0.97; 95% CI: 0.51-1.85; P = 0.92). No statistical difference was found in our study among RIMN and plate fixation in the treatment of distal femoral fractures with regard to the incidence of non-union and wound infections. Therefore, the indication for RIMN or plating should be made individually and based on the surgeon's experience.

Comparison of Locking Plate Alone and Locking Plate Combined with 3D Printed Polymethylmethacrylate Augmentation in Treating Proximal Humerus Fractures in the Elderly

BackgroundLocking plates are widely used in open reduction internal fixation (ORIF) for proximal humeral fracture (PHF). However, the optimal surgical treatment of unstable, displaced PHF in elderly patients remains controversial. This study aimed to compare the radiological and clinical outcomes of surgical treatment of PHF in the elderly with locking plate (LP) alone and locking plate combined with 3D printed polymethylmethacrylate (PMMA) prosthesis augmentation (LP-PA). MethodsFrom May 2015 to April 2021, a total of 97 patients aged ≥ 60 years with acute unstable PHF who underwent osteosynthesis with either LP (46 patients) or LP-PA (51 patients) were retrospectively analyzed. For the LP-PA group, a customized proximal humeral prosthesis made of PMMA cement was intra-operatively fabricated by a three-dimensional (3D) printed prototype mold for the humeral medial support. Radiological outcomes were analyzed by measuring the value of neck-shaft angle (NSA) and humeral head height (HHH). The clinical outcomes were evaluated using Constant-Murley Score (CMS), Disabilities of the Arm Shoulder and Hand (DASH) score, American Shoulder and Elbow Surgeons (ASES) score, and the shoulder range of motion (ROM). Pain was measured using a visual analogue scale (VAS). ResultsAt the one-year follow-up, all fractures healed radiologically and clinically. The mean changes of NSA and HHH over the follow-up period were markedly smaller in the LP-PA group (3.8 ± 0.9° and 1.7 ± 0.3 mm) than those in the LP group (9.7 ± 2.1° and 3.2 ± 0.6 mm, both P < 0.0001). The LP-PA group also presented lower DASH score (17.1 ± 3.6), higher ASES score (89.5 ± 11.2) and better ROM in forward elevation (142 ± 26°) and external rotation (59 ± 11°) compared to the LP group (28.9 ± 4.8 for DASH score, P < 0.0001; 82.3 ± 9.0 for ASES score, P < 0.001; 129 ± 21° for forward elevation, P = 0.008; and 52 ± 9° for external rotation, P = 0.001). There was no significant difference in overall complication rate between the two groups, although the complication rate of screw perforation was higher in the LP-PA group (P = 0.172). ConclusionsFor PHF in elderly patients, the combination of LP fixation and PMMA prosthesis augmentation effectively improved humeral head support and reduction maintenance, providing satisfactory outcomes both radiologically and clinically. This technique also reduced the incidence of screw perforation associated with plate fixation alone, making it a reasonable option to ensure satisfactory clinical outcomes.

Effect of Varus-Producing Distal Femoral Osteotomy and High Tibial Osteotomy on Compartment Pressures and Contact Area at Varying Degrees of Knee Flexion.

In patients with valgus alignment and degenerative changes in the lateral compartment, both distal femoral osteotomy (DFO) and high tibial osteotomy (HTO) can be used to unload the lateral compartment. Prior studies have shown that in valgus knees, the tibial wear is posterior and DFO exerts the greatest effect in extension; however, its effect is decreased as flexion angle rises. Medial closing-wedge (MCW) HTO would significantly decrease contact area, mean contact pressure (MCP), and peak contact pressure (PCP) in the lateral knee compartment through knee flexion to a greater extent compared with lateral opening-wedge (LOW) DFO. Controlled laboratory study. MCWHTO and LOWDFO were performed, correcting a mean of 8° of valgus alignment, in 10 cadaveric knees using plate fixation. Tibiofemoral contact pressure of the medial and lateral compartments was measured in 0°, 30°, 60°, and 90° of knee flexion before and after osteotomy using thin electronic sensors and load applied through an Instron device. PCP, MCP, and contact area were measured for each condition. The lateral MCP was significantly decreased in the HTO state compared with the native state in 30° (P = .015), 60° (P = .0199), and 90° (P < .0001) of flexion. The lateral MCP was also significantly decreased in the HTO state when compared with the DFO state in 60° (P = .0093) and 90° of flexion (P < .0001). After DFO, the lateral MCP returned to that of the native state in 60° (P > .999) and 90° (P > .999) of flexion. The lateral PCP decreased for all test states in all degrees of flexion; the HTO state was significantly decreased when compared with the native state in 60° (P < .0001) and 90° (P < .0001). With varus corrections of 8°, MCWHTO was more effective at unloading the lateral compartment than LOWDFO. This effect was significant as the knee flexion angle increased. This study should be considered as one aspect of the surgical decision-making process. In patients with mild to moderate valgus deformity without hypoplastic lateral femoral condyle and without significant joint line obliquity, MCWHTO may improve offloading of the lateral compartment in flexion.

Application of Intramedullary Calcar Support Plate and Lateral Locking Plate in Elderly Patients with Neer 3 and 4-Part Fractures of Proximal Humerus Through a Deltoid Splitting Approach

BackgroundThe reduction and fixation of Medial humeral calcar is difficult in the treatment of elderly proximal humerus Neer 3 and 4-part fractures with a single lateral locking plate. Our study investigated the efficacy of an intramedullary calcar supporting plate combined with a lateral locking plate for the treatment of 3- and 4-part fractures of the proximal humerus in the elderly through a deltoid splitting approach.MethodsFrom June 2022 to December 2022, we treated six elderly patients with Neer 3 and 4-part fractures using proximal humeral intramedullary calcar support plate in combination with lateral locking plate through a deltoid splitting approach. Follow-up time was 6–12 months. Assessment indicators included fracture union, quality of reduction, and complication rate. The Constant-Murley score was used to record shoulder function at 6 months postoperatively.ResultsAll 6 patients showed fracture union and anatomic reduction. Constant-Murley score was 79.5 (70–90) at 6 months postoperatively. There was no incision non-healing, internal fixation failure, bone non-union or surgical site infection, secondary surgery, or death. Shoulder impingement occurred in 1 case.ConclusionProximal humeral intramedullary calcar support plate combined with lateral locking plate fixation through a deltoid splitting approach can effectively maintain fracture reduction, prevent inversion collapse of humeral head and internal fixation failure, and provide satisfactory clinical results at an early stage.

Comparative Outcomes of Elastic Stable Intramedullary Nailing vs. Plate Fixation in Pediatric Femoral Shaft Fractures. A Prospective Study.

Pediatric femoral fractures are common in emergency rooms, with treatment options varying by age. This study compares elastic stable intramedullary nailing (ESIN) and plate fixation for diaphyseal femoral fractures in children aged 5-10. Conducted at Al-Kindi Teaching Hospital, Baghdad, from December 2017 to December 2019, this prospective study included 32 children with closed transverse diaphyseal femoral fractures. Patients were divided into two groups: 16 treated with ESIN (Group 1) and 16 with plate fixation (Group 2). Criteria excluded comminuted, open, or pathological fractures. Group 1 had a mean age of 7.1 years and weight of 23.7 kg; Group 2 had a mean age of 7.8 years and weight of 30.9 kg. ESIN resulted in shorter operative times (58.4 minutes), earlier weight-bearing, and quicker fracture union (8.8 weeks) compared to plate fixation (76.3 minutes, 11.9 weeks). Blood loss was significantly less in Group 1 (32.8 ml) versus Group 2 (205.0 ml). No significant differences in wound healing or leg length discrepancies were observed. 1. Our study indicates a preference for Elastic Stable Intramedullary Nailing (ESIN) over plate fixation for pediatric femoral shaft fractures in children aged 5-10 years. 2. ESIN is associated with shorter operative times and faster commencement of weight-bearing, critical in pediatric recovery. 3. While ESIN is generally preferable, plate fixation may be better suited in certain clinical scenarios, emphasizing the importance of personalized treatment. 4. Based on our findings, ESIN is recommended for treating transverse diaphyseal femur fractures in the specified pediatric age group. 5. Recommends further studies, including randomized controlled trials, for a more comprehensive understanding of these treatments' long-term outcomes.

Induced membrane technique with plate fixation has a lower complication rate than bone transport over a plate for segmental tibial defects larger than 5cm.

The treatment of segmental tibial bone defects remains a surgical challenge. While Bone Transport (BT) and Induced Membrane Technique (IMT) are effective strategies for regenerating bone, there are few comparative studies between them. This investigation undertakes a comparative analysis of BT and IMT for large segmental tibial defects stabilised through plate fixation. Patients with segmental tibial defects exceeding 5cm were prospectively enrolled from 2008 to 2021 in a single institution, with a minimum follow-up duration of two years. All patients underwent either BT or IMT with plate fixation of the tibia. Procedural success, primary union as well as bone and functional outcome scores were compared. Complications, including non-unions, joint contractures and deep infections requiring surgical intervention, were also compared. 41 patients were recruited in total. 28 patients underwent Bone Transport Over a Plate (BTOP), while 13 patients underwent IMT with Plate fixation (IMTP). The procedural success rate trended higher in IMTP compared to BTOP (100% vs. 85.7%). The primary union rate also trended higher in IMTP compared to BTOP (92.3% vs. 79.2%). BTOP and IMTP achieved similar rates of satisfactory bone outcome scores (78.6% vs. 84.6%) and functional outcome scores (75% vs. 76.5%). There was no statistical difference between procedural success, primary union, bone and functional outcome scores. The complication rate in BTOP was 78.6% (22 of 28), including five docking site or regenerate non-unions, eight deep infections and nine joint contractures. IMTP had a 38.5% (5 of 13) complication rate, including one non-union, two deep infections and two joint contractures. The complication rate was 2.04 times higher in BTOP compared to IMTP (p = 0.0117). BTOP and IMTP are both equally effective techniques for regenerating bone in large tibial bone defects. However, IMTP may be a safer procedure than BTOP, with a lower probability of requiring additional procedures to address complications.

Outcomes of Distal Third Femur Fractures in Patients 18 Years and Older: A Pilot Study.

The selection of the most optimal fixation method for fractures of the distal femur, whether intramedullary nail (NL), lateral locking plate (PL), or nail/plate (NP) is not always clear. This study retrospectively evaluates surgical patients with distal femur fractures and introduces a pilot study using cluster analysis to identify the most optimal fracture fixation method for a given fracture type. This is a retrospective cohort study of patients 18 years and older with an isolated distal femur fracture who presented to our Level-1 trauma center between January 1, 2012, and December 31, 2022, and obtained NL, PL, or NP implants. Patients with polytrauma and those without at least six months of follow-up were excluded. A chart review was used to obtain demographics, fracture classification, fixation method, and postoperative complications. A cluster analysis was performed. The following factors were used to determine a successful outcome: ambulatory status pre-injury and 6-12 months postoperatively, infection, non-union, mortality, and implant failure. A total of 169 patients met inclusion criteria. No statistically significant association between the fracture classification and fixation type with overall outcome was found. However, patients treated with an NP (n = 14) had a success rate of 92.9% vs only a 68.1% success rate in those treated with a PL (n = 116) (p = 0.106). The most notable findings in the cluster analysis (15 total clusters) included transverse extraarticular fractures demonstrating 100% success if treated with NP (n = 6), 50% success with NL (n=2), and 78.57% success with PL fixation (n=14). NP constructs in complete articular fractures demonstrated success in 100% of patients (n = 5), whereas 77.78% of patients treated with NL (n = 9) and 61.36% of those treated with PL (n = 44). Plate fixation was the predominant fixation method used for distal third femur fractures regardless of fracture classification.However, NP constructs trended towards improved success rates, especially in complete intraarticular and transverse extraarticular fractures, suggesting the potential benefit of additional fixation with these fractures. Cluster analysis provided a heuristic way of creating patient profiles in patients with distal third femur fractures. However, a larger cohort study is needed to corroborate these findings to ultimately develop a clinical decision-making tool that also accounts for patient specific characteristics.

Clinical and Radiographic Outcomes of Anterior Lumbar Interbody Fusion With Anterior Plate Fixation.

Reports on the outcomes following instrumented anterior lumbar interbody fusion (ALIF) with anterior plate fixation are limited. The aim of this study was to assess the clinical and radiographic outcomes of patients undergoing ALIF with anterior plate fixation. Methods: Medical records and radiographic imaging were reviewed for 100 patients who received ALIF with anterior plate fixation between 2008 to 2021 and completed at least one year of follow-up and postoperative imaging. Prospectively collected patient data included indication for surgery, BMI, age, number and location of levels treated, complications, reoperation rates, fusion rate, and measurements of global lordosis, disc space height, and segmental angulation. Results: A total of 100 patients were included in this study. The mean length of follow-up was 81.37 months. Changes in preoperative-to-postoperative Oswestry Disability Index (ODI) and Visual Analog Score (VAS) demonstrated improvements of 30.86% and 18.56%, respectively. Major vascular injuries occurred in 3% of the cases. A hardware failure rate of 5% was observed. The reoperation rate was 10%. The radiographic fusion rate derived from computed tomography (CT) and plain film was 95.45% and 88.87%, respectively. Postoperative global lordosis demonstrated a 6.08% increase. Postoperative segmental angulation measurements increased by 57.74%. No statistically significant differences in clinical or radiographic outcomes were observed based on the spine level of fusion or the number of fusions performed. Conclusions: ALIF with anterior plate fixation achieved an adequate fusion rate with improvements in ODI and VAS scores meeting minimal clinically important difference thresholds. Postoperative disc space heights demonstrated significant improvements compared to preoperative measurements.

Comparison of Intramedullary Screw Fixation, Plating, and K-Wires for Metacarpal Fracture Fixation: A Meta-Analysis.

Metacarpal fractures are common injuries with multiple options for fixation. Our purpose was to compare outcomes in metacarpal fractures treated with intramedullary screw fixation (IMF), Kirschner wires (K-wires), or plating. A systematic literature review using the MEDLINE database was performed for studies investigating metacarpal fractures treated with IMF, plating, or K-wires. We identified 34 studies (9 IMF, 8 plating, 17 K-wires). A meta-analysis using both mixed and fixed effects models was performed. Outcome measures included mean Disabilities of the Arm, Shoulder, and Hand (DASH) scores, total active motion (TAM), grip strength, time to radiographic healing, and rates of infection and reoperation. Patients with IMF had significantly lower DASH scores (0.6 [95% confidence interval [CI], 0.2-1.0]) compared with K-wires (7.4 [4.8-9.9]) and plating (9.8 [5.3-14.3]). Intramedullary screw fixation also had significantly lower rates of reoperation (4%, [2%-7%]), compared with K-wires (11% [7%-16%]) and plating (11% [0.07-0.17]). Grip strength was significantly higher in IMF (104.4% [97.0-111.8]) compared with K-wires (88.5%, [88.3-88.7]) and plating (90.3%, [85.4-95.2]). Mean odds ratio time was similar between IMF (21.0 minutes [10.4-31.6]) and K-wires (20.8 minutes [14.0-27.6]), but both were shorter compared with plating (52.6 minutes [33.1-72.1]). There were no statistically significant differences in time to radiographic healing, TAM, or rates of reoperation or infection. This meta-analysis compared the outcomes of metacarpal fixation with IMF, K-wires, or plating. Intramedullary screw fixation provided statistically significant lower DASH scores, higher grip strength, and lower rates of reoperation, suggesting that it is a comparable method of fixation to K-wires and plating for metacarpal fractures.