Pin Insertion Research Articles

Effect of CFRP pin reinforcement and manufacturing technique on shear and dynamic properties of flat-joggle-flat composite joints

The present research investigates the integrated influence of production procedures and the placement of carbon fibre pins on the shear and vibrational characteristics of flat-joggle-flat composite joints. Results exhibit that the insertion of pins in co-cured flat-joggle-flat joints with a 2 % volume fraction greatly improved the tensile and shear parameters by 35.04 % and 31.96 %, respectively, compared to co-bonding and secondary bonding. The addition of more % of pin decreased the strength properties due to more stress concentration at the pin corners. The failure analysis reveals that without reinforcement samples mostly failed in cohesive and adhesive manners. FESEM images confirmed that the pin insertion provides the bridging between the adhesive and adherends. The modal analysis reveals the co-cured connection had highest natural frequencies (985.1 Hz) than other joints, indicating improved interface bonding between the adhesive and adherends.

EVALUATION OF THE SELF-DRILLING, SELF-TAPPING SCHANZ PIN THREAD PATTERNS ON THE NEAR CORTEX WHEN INSERTED IN BONE WITHOUT PRE-DRILLING

The external fixator is an invaluable device when treating acute complex trauma and in limb reconstruction. It is therefore important to ensure its efficient and safe application to avoid complications. A lot of research has been done to evaluate the factors around external fixator stability, pin site infections and more is still being done to understand pin loosening. The purpose of this study was to evaluate other factors that may contribute in external fixator pin loosening. The aim was to evaluate if the different Schanz pin insertion techniques contribute to pin loosening.Two tibia diaphyses from two cadavers were each divided into three sections. Three different drilling techniques were repeated in each of the sections. A total of 36 Schanz pins were inserted and a section cut out of the bone in front of the pins was done allowing visual inspection of the pin hole for features of thread stripping. These features were predefined as thread pattern disruption, smoothening and shallow imprint on the cortex.Evidence of pin thread stripping was seen in all of the pin insertion techniques. The first method where the hole was pre-drilled and pin inserted with the drill showed 100% thread stripping. The second method of pre-drilling and hand insertion showed the least amount with 16.7% of pin stripping noted and 66.7% pin thread stripping was observed when inserting the pin with power without pre-drilling the pilot hole using the third method.Different pin insertion techniques result in varying amounts of pin thread stripping. The most amount of thread stripping occurs when a Schanz pin is inserted with power after pre-drilling. This finding, although not measured scientifically, supports the current recommendation of pre-drilling and manual insertion of the pin. In future, more scientific measurement are necessary to quantify these findings and assess their clinical significance.

ORTHOPAEDIC TRAUMA EMERGENCIES DONE AFTER HOURS

In 2019, the incidence of fractures were 178 million globally, South Africa accounting for close to 600 000 of these fractures, an 18.53% increase since 1990. South Africa does not have the public infrastructure to adequately facilitate the optimal surgical management of this burden. This forces intensive labour practices among orthopaedic surgeons, often performing complex surgeries throughout the night. There is a direct correlation between “after-hour”operations and the increase in morbidities.A retrospective review of the orthopaedic surgical cases and orthopaedic surgical emergencies done at a tertiary institution in Johannesburg between 8th of August 2021 to 12th December 2022. The nature of the orthopaedic interventions, the date of booking of the surgical procedures, date of surgical procedures, as well as start and end time of the orthopaedic interventions were analysed.“After-Hours” orthopaedic interventions were defined as interventions done between 16:00 and 07:00. Orthopaedic emergencies were defined as: Open fracture debridements, external Fixator insertion, arthrotomies, fasciotomies and the insertion of steinmann pins. 1483 (27.92%) of 5310 operative cases done on the emergency board were orthopaedic cases. 1098 (74.04%) hardware-related cases and 535 (36.08%) orthopaedic emergencies were done. 854 (57.58%) cases were done “After-Hours” of which 433 (29.20%) cases were done during “Dead-Hours” (23:00–07:00). Of these 433 cases, only 173 (39.95%) were true orthopaedic emergencies.Although the proportion of emergencies done after hours were greater than during working hours, there is still a large proportion of intricate orthopaedic cases done between 16:00– 07:00 that should not be prioritized, due to an associated higher morbidity. Enhanced strategic planning is advisable in future in order to prioritize complex hardware cases during working hours, and due to the burden, prioritize minor relooks and simple skin- grafts for the latter aspects of the night. A dedicated Orthopaedic Trauma theatre is recommended.

Pre-Induction Scalp Block in a Patient of von HippelLindau Disease: Promising Use in High-Risk Neurosurgical Procedures

Multiple modalities have been tried for post-craniotomy pain relief, but controversy exists as to the optimal approach. Pre-induction scalp block is a promising technique in high-risk neurosurgical procedures, which reduces the haemodynamic response to skull pin insertion and craniotomy incision, and affords post-operative analgesia. von hippel-lindau (VHL) disease is a rare autosomal dominant disorder with multi-system involvement and various visceral manifestations, the most common of these-being cerebellar hemangioblastoma. Other anomalies include pancreatic-renal cysts, erythrocytosis, hypernephroma, pheochromocytoma and retinal capillary hemangioblastoma. Central nervous system (CNS) hemangioblastomas are often an early manifestation of the disease, and are typically seen in the second decade of life. The majority of hemangioblastomas occur in the cerebellum followed by the spinal cord and brain stem. They are benign vascular tumours but can cause neurological symptoms secondary to pressure or haemorrhage. We hereby present a case of previously diagnosed VHL with recurrent cerebellar hemangioblastoma scheduled for neurosurgical tumour excision and the beneficial use of a pre-induction scalp block to compliment anaesthesia for the patient.

A Cadaveric Feasibility Study of an Automatic Multi-Degrees of Freedom Surgical Robot for Percutaneous Scaphoid Guide Pin Insertion.

Background: Percutaneous fixation of scaphoid fractures need accurate guide pin insertion. The emergence of computer-assisted navigation and robotic surgery may provide a promising solution to this problem. Methods: This study presents the development of an automatic multi-degrees of freedom (DOF) surgical robot with computer-assisted navigation system, focusing on percutaneous scaphoid guide pin insertion. Using this device, along with a 3D fluoroscopy unit, we have conducted an experimental study on 10 cadavers for percutaneous scaphoid guide pin insertion to verify the feasibility and reliability of the system. Results: The mean operative duration was 29.1 (SD 4.3) minutes. The cadavers required no more than two attempts to achieve desired wire placement, with the mean positioning-error being 2.0 (SD 0.3) mm and the mean angle-deviation 3.6 (SD 0.7)°. Throughout the study, a mean of 2.2 full-cycle fluoroscopy attempts was required for each cadaver during surgery, and no preoperative CT scan was needed. Conclusions: The outcomes show that using the automatic surgical robot to perform the percutaneous scaphoid guide pin insertion is feasible and desired results can be achieved.

Sterile Silicone Studs–A Nonpharmacologic Modality for Prevention of Hemodynamic Response to Skull Pin Insertion: A Pilot Study

Application of surgical skull pins causes hemodynamic fluctuations in neurosurgical procedures. To reduce this response, we describe the use of a novel nonpharmacologic method in the form of medical-grade sterile silicone studs to cushion the pressure of the skull pin in the adult population. This study aimed to evaluate the use of conventionally used fentanyl and medical-grade sterile silicone studs for the prevention of hemodynamic response to skull pin insertion. A prospective randomized pilot study was conducted of 20 adult patients categorized as American Society of Anesthesiologists class I and II scheduled for elective craniotomy in November 2022 in a tertiary-care hospital in Chandigarh, India. Patients were randomized into 2 groups: fentanyl only (FO group; n= 10) and medical-grade silicone studs (SS group; n= 10). Heart rate and mean arterial pressure were recorded at the following intervals: T1, baseline; T2, before induction; T3, after intubation; T4, before skull pin insertion; T5, T6, T7, T8, T9, and T10 at 0, 1, 3, 4, and 5 minutes after skull pin insertion. Demographic data (e.g., sex, age, disease pathology) were comparable between the groups. Although changes in heart rate between the 2 groups were comparable, there was a statistically significant decrease in mean arterial pressure from 1 minute to 5 minutes after pinning in patients with silicone studs compared with patients who received only fentanyl. The use of medical-grade silicone studs causes fewer hemodynamic fluctuations compared with fentanyl on skull pinning. Further studies with larger sample sizes are required to confirm the findings of this pilot study.

Evaluation of Clinical Efficacy of Scalp Block with 0.25% Injection Bupivacaine and 0.25% Injection Levobupivacaine to Blunt the Hemodynamic Response to Skull Pin Insertion during Supratentorial Craniotomies - A Prospective Study

BACKGROUND
 Head fixation is necessary to maintain the desired head position. Application of skull pins in neurosurgery leads to hemodynamic changes and this sudden change can be prevented by combining general anaesthesia with scalp block which blocks supraorbital nerve, supratrochlear nerve, zygomaticotemporal nerve, auriculotemporal nerve, lesser occipital nerve and greater occipital nerve which are present in superficial and deep layers of the scalp. Several studies have been done to study the efficacy of Injection levobupivacaine and injection bupivacaine in 0.5 % concentrations for scalp block. However, the comparative efficacy of 0.25% injection levobupivacaine and injection bupivacaine for scalp block has not been determined by any study previously. We wanted to compare the efficacy of 0.25% injection levobupivacaine and 0.25% injection bupivacaine in scalp block on the haemodynamic response to head pinning, incision and during craniotomy.
 METHODS
 This prospective randomised study included 60 patients of ASA status I or II between age 18–60 years and of either sex who underwent supratentorial craniotomy under general anaesthesia followed by scalp block. Patients were randomly allocated into two groups of 30 each and before application of the Mayfield skull pin head holder, scalp block was given as per group distribution (Group A: 20 ml 0.25% injection bupivacaine and Group B: 20 ml of 0.25% injection levobupivacaine). The hemodynamic responses were recorded at baseline, during scalp block and after head pin insertion, incision and at craniotomy. The total analgesic requirement during intraoperative and post operative period was noted.
 RESULTS
 There were no clinically and statistically significant differences in values of heart rate and blood pressure after head pin insertion, skin incision and craniotomy in both the groups.
 CONCLUSIONS
 The study revealed that 0.25% injection levobupivacaine when used for scalp block was as efficacious as 0.25% injection bupivacaine. Both the drugs in low concentration of 0.25% were effective in minimizing pressor response to skull pin insertion, incision and craniotomy with less incidence of complication and reduced intraoperative requirement of analgesia.

COMPARISON OF DEXMEDETOMIDINE AND CLONIDINE AS AN ADJUVANT TO BUPIVACAINE IN SCALP BLOCK FOR SUPRATENTORIAL CRANIOTOMY SURGERY - A PROSPECTIVE, RANDOMISED INDIAN STUDY

Background: Current era of minimally invasive surgery and awake craniotomy has created revived attention towards scalp blocks and its benefits. Present study was conducted to evaluate and compare effects of dexmedetomidine and clonidine as an adjuvant to bupivacaine in scalp block for supratentorial craniotomy surgery. Methods: The prospective, comparative, randomized study was conducted by Department of Anaesthesia at J.J. Hospital and Grant Medical College, Mumbai, India. Data was collected between September 2018 to August 2020. Adult subjects between 18 years and 60 years (both inclusive) of either gender with ASA-I, Glasgow Coma Scale (GCS) of 15, and indicated to undergo supratentorial craniotomy surgeries were enrolled. One study group received 1 mcg/kg Clonidine, while other 1 mcg/kg Dexmedetomidine, both diluted with normal saline. Hemodynamic parameters, analgesic requirement and Ramsay Sedation score (RSS) were assessed. Results: 60 patients (30 in each group) were enrolled. Mean age, baseline weight, gender distribution and duration of surgery were statistically comparable between study groups (P>0.05). Mean blood pressure, mean arterial pressure and heart rate were significantly higher in the clonidine group at the time of pin insertion, incision and during most of the intraoperative period (p<0.05). RSS was comparable between study groups at all time-points (p>0.05). Analgesic requirement was overall higher in clonidine group, indicating better analgesia with Dexmedetomidine. Conclusion: Dexmedetomidine led to lesser vascular parameters changes, with lower analgesic requirement versus clonidine however, sedation scores were comparable.

Mixed-reality visualization in shoulder arthroplasty: is it better than traditional preoperative planning software?

Preoperative traditional software planning (TSP) is a method used to assist surgeons with implant selection and glenoid guide-pin insertion in shoulder arthroplasty. Mixed-Reality (MR) is a new technology that uses digital holograms of the preoperative plan and guide-pin trajectory projected into the operative field. The purpose of this study was to compare TSP to MR in a simulated surgical environment involving insertion of guide-pins into models of severely deformed glenoids. Eight surgeons inserted guide-pins into eight randomized three-dimensional-printed severely eroded glenoid models in a simulated surgical environment using either TSP or MR. In total, 128 glenoid models were used and statistically compared. The outcomes compared between techniques included procedural time, difference in guide-pin start point, difference in version and inclination, and surgeon confidence via a confidence rating scale. When comparing traditional preoperative software planning to MR visualization as techniques to assist surgeons in glenoid guide pin insertion, there were no statistically significant differences in terms of mean procedure time (P=0.634), glenoid start-point (TSP = 2.2 ± 0.2 mm , MR = 2.1 ± 0.1 mm; P=0.760), guide-pin orientation (P=0.586), or confidence rating score (P=0.850). The results demonstrate that there were no significant differences between traditional preoperative software planning and MR visualization for guide-pin placement into models of eroded glenoids. A perceived benefit of MR is the real-time intraoperative visibility of the surgical plan and the patient’s anatomy; however, this did not translate into decreased procedural time or improved guide-pin position. Level of evidence: Basic Science Study; Biomechanics.

Anatomic consideration of the radial nerve in relation to humeral length for unilateral external fixation: a retrospective study using magnetic resonance imaging findings in korean

BackgroundThis study aimed to present a safe zone for distal pin insertion for external fixation using magnetic resonance imaging (MRI) images.MethodsAll patients who took at least one upper arm MRI from June 2003 to July 2021 were searched via a clinical data warehouse. For measuring the humerus length, proximal and distal landmarks were set as the highest protruding point of the humeral head and lowermost margin of ossified bone of the lateral condyle, respectively. For children or adolescents with incomplete ossification, the uppermost and lowermost ossified margin of the ossification centers were set as proximal and distal landmarks respectively. The anterior exit point (AEP) was defined as the location of the radial nerve exiting the lateral intermuscular septum to the anterior humerus and distance between the distal margin of the humerus and AEP was measured. The proportions between the AEP and full humeral length were calculated.ResultsA total of 132 patients were enrolled for final analysis. The mean humerus length was 29.4 cm (range 12.9–34.6 cm). The mean distance between the ossified lateral condyle and AEP was 6.6 cm (range 3.0–10.6 cm). The mean ratio of the anterior exit point and humeral length was 22.5% (range 15.1–30.8%). The minimum ratio was 15.1%.ConclusionA percutaneous distal pin insertion for humeral lengthening with an external fixator may be safely done within 15% length of the distal humerus. If pin insertion is required more proximal than distal 15% of the humeral shaft, an open procedure or preoperative radiographic assessment is advised to prevent iatrogenic radial nerve injury.

Biomechanical comparison of one pin versus two pin fixation in a canine tibial tuberosity avulsion fracture model.

To determine whether one larger or two smaller diameter pins used for tibial tuberosity avulsion fracture (TTAF) stabilization provides greater axial tensile strength and stiffness when subjected to monotonic mechanical load to failure in normal skeletally mature canine cadavers. Paired ex vivo biomechanical study. Eleven pairs of adult cadaveric dog tibias. Twenty-two tibias from 11 dogs were collected to model a TTAF. Each limb of a pair was randomly assigned a one or two-pin fixation. Tibias were subjected to monotonic, axial load to failure. Fixation stiffness, strength, and pin insertion angles were analyzed with parametric testing. Significance was set at p < .05. The mean strength of the single-pin fixation was 426.2 ± 50.5 N compared to two-pin fixation at 639.2 ± 173.5 N (p = .003). The mean stiffness of the single-pin fixation was 57.3 ± 18.7 N/mm and the two-pin fixation was 71.7 ± 20.5 N/mm (p = .029). The normalized ratio between one and two-pin fixation had a mean stiffness of 68% ± 25.8% and strength of 82.8% ± 24.6%. In an ex vivo cadaveric TTAF model, vertically aligned two-pin fixation offers greater strength and stiffness when compared to a single-pin fixation. When repairing TTAF, surgeons should aim to apply two vertically aligned pins rather than a single pin for greater strength and stiffness.

Effect of tool pin length on interfacial behaviors and mechanical properties of friction stir-welded lap joints of 430/304 stainless steels

In this study, the effect of tool pin length on friction stir lap welding of 430 and 304 stainless steels has been investigated. The thermal history of interface was measured by thermocouple. The interfacial macro- and micro-structures under different tool pin lengths were analyzed via optical microscope and scanning electron microscope. Also, tensile shear tests were carried out to evaluate the strength of the lap joint. The results show that increasing the pin length from 0.5 to 1.3 mm increases the peak temperature of the interface, which has a significant effect on diffusion layer formation and hook geometry. The fracture mode of the joints shifts from shear fracture to tensile fracture with the increase of the pin insertion depth. When the pin length is 1.0 mm, i.e., a slight penetration into the 304 plate, the joint presents a maximum failure load of 2.86 kN. The findings reveal that the effective top plate thickness (Teff) used to describe the hook geometry is an important factor determining the joint strength and fracture mode.

Robotic-assisted total knee arthroplasty is not associated with increased risk of postoperative deep vein thrombosis

PurposeProlongation of operation time due to registration and pin insertion has been reported with robotic-assisted total knee arthroplasty (RATKA), and there has been concern about an increase in the postoperative incidence of deep vein thrombosis (DVT). In this study, we compared the incidence of DVT after RATKA with that after conventional manual TKA (mTKA).MethodsThis consecutive retrospective series included 141 knees that underwent primary TKA using the Journey II system. The CORI robot was used. There were 60 RATKAs and 81 mTKAs. Doppler ultrasound was performed in all patients on postoperative day 7 to determine whether DVT was present.ResultsThe operation time was longer in the RATKA cohort (99.5 min vs 78.0 min, p < 0.001). The overall incidence of DTV was 43.9% (62/141 knees), all of which were asymptomatic. There was no significant difference in incidence of DVT between RATKA and mTKA (50.0% vs 39.5%, p = 0.23). Use of the robot did not affect the incidence of DVT following TKA (odds ratio 1.02, 95% confidence interval 0.40–2.60; p = 0.96).ConclusionThe incidence of DVT was not significantly different between RA-TKA and mTKA. Multiple logistic regression indicated that RATKA is not associated with increased risk of postoperative DVT.Level of evidenceIV.

Accelerometer-Based Handheld Navigation Instrumentation in Total Knee Arthroplasty Decrease Blood Loss Compared to Conventional Instrumentation: A Prospective Comparative Study.

Introduction Total Knee Arthroplasty (TKA) can be associated with significant peri- and post-operative blood loss necessitating blood transfusion. The blood loss may be relatively less when the accelerometer-based handheld navigation system (HHNS) is used, as there is neither a need for intramedullary breach nor additional pin insertions. The primary hypothesis was that HHNS instrumentation reduced perioperative blood loss when compared with conventional instrumentation, and to prove this, we compared the perioperative parameters like tourniquet time, hemoglobin loss, and estimated blood loss between patients undergoing total knee arthroplasty using conventional instrumentation with handheld navigation instrumentation. Methods This prospective comparative study involves 40 patients in the HHNS groupand 40 patients in the conventional group based on the instrumentation used, respectively. Tourniquet was used in all the cases. Patient characteristics like age, sex, body mass index (BMI), American Society of Anaesthesiologists (ASA) grade, and Charlson Comorbidity Index (CCI) were recorded. The perioperative parameters like tourniquet time, the estimated blood loss, hemoglobin loss, blood transfusions, and the number of units transfused were recorded and compared between the groups. Results There was no significant difference in age, BMI, ASA grade, or CCI between the two groups. The tourniquet time was 83.7 ± 9.6 in the navigation and 73.9 ± 10.3 in the conventional group. The estimated Hb loss was lower at 2.5 ± 1.6 in the HHNS group compared to 3.0 ± 1.8 in the conventional group (p<0.001). Similarly, estimated blood loss was also lower at 830 ± 285ml for the HHNS group compared to 1088 ± 228 in the conventional group. Two patients in the navigation group had a total of four units transfused, whereas three patients in the conventional group had five units of blood transfusion. Conclusions The primary hypothesis that HHNS reduced perioperative blood loss was confirmed by the results of our study. We demonstrated that HHNS instrumentation significantly decreased the estimated blood loss, drain volume, and hemoglobin loss compared to conventional instrumentation with similar operating times. Though blood transfusions were seen in fewer patients, there was no significant reduction in blood transfusions by HHNS instrumentation.

The effectiveness of scalp nerve block on hemodynamic response in craniotomy: a systematic review and meta-analysis of randomized trials.

Strategies that blunt noxious stimuli and stabilize hemodynamics may reduce perioperative cardiovascular complications and enhance recovery after craniotomy. Our systematic literature review and meta-analysis investigated whether scalp nerve block (SNB) reduces the acute hemodynamic response compared with non-SNB (scalp infiltration or control) in adult patients undergoing elective craniotomy. We searched MEDLINE, EMBASE, CENTRAL, and two Chinese databases for randomized trials. Primary outcomes included mean arterial pressure and heart rate during skull pin insertion and surgical incision in craniotomy. Secondary outcomes included incidence of hypertension and dosage of intraoperative analgesic opioids used. Random-effects models were used for meta-analyses. SNB significantly reduced the mean arterial pressure (mean difference: -14.00 mmHg; 95% confidence interval [CI]: -19.71 to -8.28) and heart rate (mean difference: -11.55 beat/min; 95% CI: -19.31 to -3.80), when compared with non-SNB during skull pin insertion. A similar trend was observed during skin incisions (SNB vs. non-SNB, mean difference in mean arterial pressure: -9.46 mmHg; 95% CI: -14.53 to -4.38; mean difference in heart rate: -9.34 beat/min; 95% CI: -15.40 to -3.28). Subgroup analysis showed that, compared with scalp infiltration, SNB reduced mean arterial pressure and heart during pin insertion but not during skin incisions. SNB also reduced the incidence of intraoperative hypertension, but no difference was observed in intraoperative opioid consumption when compared with non-SNB. SNB alleviated the craniotomy-associated hemodynamic response. SNB may be superior to scalp infiltration in maintaining hemodynamic stability during pin insertion. However, high-quality trials are still needed to provide more conclusive evidence.

Pullout strength of connected pins in hand surgery: Effect of pin diameter and insertion angle

ObjectiveThe purpose of this study was to examine the effect of insertion angles on the pullout strength of connected pins using a synthetic model simulating a hand bone. Material and methodsThe material consisted of Sawbones® (20 mm×20 mm × 60 mm), fixation pins secured to a connecting rod much like an external fixator, an electric drill (speed 1,290 rpm) and a tensile testing machine. The Sawbones® were drilled with different pin diameters (1.2 mm, 1.5 mm, and 1.8 mm) and insertion angles (100°, 110° and 120°). A vertical displacement of 1 mm/min was applied until the pins were extracted (maximum force). ResultsThe pullout strength increased with the insertion angle of the connected pins. It also increased with their diameter. Regardless of the pin diameter, the load-displacement curve during the pullout test had 4 sections (peak 1, ascending slope, peak 2, descending slope) that corresponded to the combined frictional force and contact force between the pins and Sawbones®. DiscussionOur study findings showed that, theoretically, for wrist or hand fractures treated with connected pins, the larger the diameter and insertion angle, the better the mechanical holding power of the pins. Level of evidenceI, experimental study.

A Comparative Study of Intravenous Dexmedetomidine with Local Infiltration of Ropivacaine in Attenuation of Stress Response to Skull Pin Insertion in Craniotomies.

Objective Skull pin insertion in patients undergoing craniotomies elicits hemodynamic and neuroendocrine stress response that may be deleterious to the patient. Various drugs and techniques have been documented in literature to abate this stress response. Against this background, we aimed to compare the efficacy of intravenous dexmedetomidine and local infiltration of ropivacaine for attenuation of stress response to pin insertion in craniotomies. Methods Eighty-eight adult patients undergoing craniotomy under general anesthesia from March 2019 to April 2020 requiring application of head holder were randomized into two equal groups. After intubation, 0.75 µg kg -1 of dexmedetomidine over 10 minutes through infusion was given in group D, while local infiltration at pin sites was done with 0.5% ropivacaine, 2 mL at each site in group R. Hemodynamic parameters and levels of serum cortisol, prolactin, and blood glucose were measured before and after pin insertion. Unpaired t -test for continuous variables and Mann-Whitney U test was used for nonnormally distributed variables. Results Heart rate was statistically similar between the two groups at all the observed time points. The difference in mean arterial pressure values between the two groups was found to be statistically significant only from 10 to 20 minutes after pin insertion being statistically similar at rest of the time points. Levels of serum glucose, cortisol, and prolactin values 30 minutes after pin insertion were statistically similar between both groups. Conclusion We concluded that both interventions are equally efficacious in attenuation of hemodynamic and stress response to head holder application in patients undergoing craniotomies.

Operative treatment of hamate fractures with hamatometacarpal fracture dislocation using a self-designed dorsal buttress locking plate with trans-metacarpal pin insertion: short-term follow-up results

Purpose: Fracture and dislocation of the hamatometacarpal joint are rare; therefore, the diagnosis is frequently missed and the treatment is not clearly established. The authors performed operative treatment of hamate fractures with hamatometacarpal fracture dislocation using a self-designed dorsal buttress locking plate. Herein, we report the clinical and radiological results.Methods: From May 2016 to February 2022, we experienced 12 cases of hamatometacarpal fracture dislocation that underwent operative treatment with a self-designed dorsal buttress locking plate. All 12 patients were male, with an average age of 30.3 years and an average postoperative follow-up period of 6 months and 1 week. Open reduction and internal fixation were performed using a self-designed dorsal buttress locking plate with trans-metacarpal pin insertion according to the patient, and the results of the treatment were evaluated radiologically and clinically.Results: All cases showed bony union in radiological evaluations at the last follow-up. In functional evaluations using the modified Mayo wrist score, the results were excellent in 11 cases and good in 1 case. There were no complications such as fixation failure, nonunion, or infection.Conclusion: In cases of hamate fracture with hamatometacarpal fracture dislocation, the dorsal displaced fragment is very small, and it is often difficult to maintain reduction by direct fixation. In these fractures, operative treatment using a self-designed dorsal buttress locking plate with trans-metacarpal pin insertion can obtain good results.

VALGUS INTERTROCHANTERIC OSTEOTOMY USING DYNAMIC HIP SCREW FOR NEGLECTED NON-UNION OF NECK OF FEMUR FRACTURE IN A MIDDLE AGED MALE-A CASE REPORT.

Neck of femur fracture is a common orthopaedic problem. The management of the non union of the neck of femur is challenging because of the biological and the mechanical factors at play. Osteosynthesis is the modality of choice for the people aged 60 years or less while arthroplasty is the treatment offered for the older age group. Numerous techniques have been described for the osteosynthesis of the non union of neck of femur. The main principle of all these methods remains optimization of the biology and mechanics of the fracture to promote fracture union and delay the onset of hip arthritis. Here we describe a case of a young middle aged male who due to ongoing COVID-19 pandemic and the imposed lockdowns was not able to receive proper healthcare. He presented to us with 9 months duration of nonunion of right neck of femur fracture. Radiographs were obtained which revealed a Pauwels type 3 fracture and a Sandhu class 2 nonunion. MRI studies were done to ascertain the viability of the femoral head. After all the investigations, a decision was taken to attempt head salvage using a Valgus intertrochanteric Osteotomy. Careful preoperative assessment and calculations were done to accurately determine the osteotomy wedge, DHS pin insertion angle and the goal Pauwels angle. It was decided to correct the Pauwels angle to 30° to reduce shear forces at the fracture site and achieve compression at the fracture site. After the surgical procedure patient was followed up and the fracture as well the osteotomy site showed the signs of union at 24 weeks post operative. Patient achieved excellent function in his hip. He was able to walk pain and limp free, he could squat, sit crosslegged and perform his day to day activites as well as his ground level activites. His post operative Harris Hip Score was 90.8(excellent) at 24 weeks follow up. We thus conclude that a carefully planned valgus intertrochanteric osteotomy is able to achieve excellent outcomes in young patients with non union of neck of femur.

Establishing a low-risk zone for a temporary extra-articular calcaneo-tibial pin fixation in an unstable ankle or subtalar joint

This study aimed to establish a low-risk zone to avoid neurovascular injury during a temporary extra-articular calcaneo-tibial pin fixation in an unstable ankle or subtalar joint. A line from the calcaneal tuberosity center to the lateral end of the posterior malleolus at the ankle joint level defines the lateral border of this zone. Another line from the calcaneal tuberosity center to the midpoint of the anterior distal tibial articular surface at the joint level defines its medial border. This region was assumed to have a low neurovascular injury risk upon pin insertion. Fifty ankles from 50 patients who had undergone magnetic resonance imaging (MRI) for ankle disorders were assessed. T1-weighted oblique axial MRI slices were oriented to the pin trajectory. The mean distances between the sural nerve and the lateral border of the low-risk zone and between the posterior tibial neurovascular structures and the medial border of the low-risk zone were 15.0 ± 2.5 (range 9.1 to 21.1) and 12.8 ± 2.6 (6.3 to 20.8) mm, respectively. No neurovascular structures were identified within the low-risk zone. These findings demonstrated that an unstable ankle or subtalar joint can be temporarily fixated with an extra-articular calcaneo-tibial pin at a defined zone with a low neurovascular injury risk.