pH Values Research Articles

Integrated study on CO2 enhanced oil recovery and geological storage in tight oil reservoirs

Carbon utilization, and sequestration (CUS) in tight oil reservoirs stands as a pivotal strategy for enhancing oil recovery and mitigating CO2 emissions. Research on CUS mainly focuses on the calculation of overall displacement efficiency and the total sequestration amount. However, the primary control and sequestration mechanisms throughout the life cycle of CUS, as well as the contribution of each mechanism at different development stages and under various injection and production parameters, are not clear, which limits effective guidance for oilfield development. Therefore, this paper studies the entire life cycle of tight oil reservoirs, from water flooding to CO2 flooding and CO2 sequestration after reservoir abandonment. The contribution degree changes of dissolution, structural, residual gas and mineralized sequestration mechanisms during the whole life cycle are analyzed. The results show that the main sequestration mechanism during CO2 flooding stage and injection sequestration stage after shutting down production wells is structural sequestration, which accounts for 84.75%. In the 2000 years following the cessation of CO2 injection, the proportion of structural sequestration gradually decreases, with a cumulative decrease of 12.41%, and it is mainly converted to the other three sequestration modes, with the largest increase in mineralization sequestration, reaching 8.81%, mainly due to the reaction of dicalcium silicate with CO2 to produce more stable calcite. When the injection pressure was increased from 23 MPa to 44 MPa, the sequestration efficiency increased by 18.45%. An interesting finding is that the solubility of CO2 in water in the target reservoir reaches its lowest point at 80 °C, and both warming and cooling at this point are conducive to the dissolution and sequestration of CO2. The initial pH value of formation water mainly affects mineralization and sequestration. The rate of calcite production and the contribution of CO2 dissolution and sequestration are positively correlated with water saturation. The findings underscore the importance of understanding dynamic contributions of various sequestration mechanisms and optimizing conditions to enhance CO2 sequestration efficiency.

Photocatalytic activity of Nb2O5-α-Fe2O3 Nanocomposites Synthesized by Sol-gel Method

In this investigation, Nb2O5-α-Fe2O3 nanocomposites were synthesized by modified sol-gel method. The obtained materials were characterized by different techniques such as powder X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), Brunauer-Emmett-Teller (BET), UV-vis diffuse reflectance (UV-vis spectroscopy). The catalyst was found to have a particle size in the region of 20-42 nm with a high surface area. The effects of the catalyst dose, the pH value, UV power, addition of H2O2 and scavenger on the photocatalytic efficiency were investigated. This study presents a strategy to eliminate highly toxic and persistent dyes such as DB 199 dye. It was observed that the nanocomposites showed maximum response with more than 80% degradation of DB 199 dye in 100 min.

Formulation of Coffee Grounds Bar Soap (Used Coffee Grounde)

Coffee consumption increases every year so that a lot of coffee grounds are wasted which can cause problems to the environment. This can be overcome by utilizing coffee grounds from various cafes/coffee shops. One of them is by making bar soap. The purpose of this study was to determine the quality of bar soap product formulations with the addition of different levels of coffee grounds based on the results of the pH test and organoleptic test. The research was conducted from October to December 2023 at the Banyorang Coffee Processing Center Office, Tompobulu Village, Banyorang District, Bantaeng Regency, South Sulawesi Province. This research method uses a Completely Randomized Design (CRD) with 4 (four) treatments, namelyformula 1 coffee grounds 40 g, palm oil 50%, coconut oil 30%, olive oil 20%, formula 2 coffee grounds 70 g, palm oil 50%, coconut oil 30%, olive oil 20%, formula 3 coffee grounds 100 g, palm oil 50%, coconut oil 30%, olive oil 20%, and formula F4 coffee grounds 130 g, palm oil 50%, coconut oil 30%, olive oil 20%. The results showed that the pH value is feasible to use bar soap for skin care 9.40 – 10.62 in accordance with SNI standards and organoleptic tests based on the criteria of color, aroma, texture, moisture, freshness, and freshness was in the formulation of 130 g coffee grounds, 50% palm oil, 30% coconut oil, and 10% olive oil.

From agricultural wastes to advanced materials for environmental applications: Rice husk-derived adsorbents for heavy metals removal from wastewater

Agroindustry annually generates enormous amounts of residues, and their re-utilization is a convenient approach to mitigate environmental pollution and increase energy savings. Rice husk (RH) is one of the most widely available agricultural wastes in many countries of the world. RH and its ashes are often used directly for manufacturing and synthesizing new materials with added-value features. In this work, the preparation of composite materials for wastewater treatment has been explored by producing and testing mesoporous iron-oxide/RH composites for heavy metal adsorption. The composites were fully characterized and their application to the removal of Pb2+ and Cu2+ ions from model aqueous solutions at different pH values was tested to evaluate their adsorption performances and select those materials more suited for realistic applications. Our results indicated that the composite materials exhibited higher metal adsorption capacities than the pristine carbonized RH and the iron components, highlighting a synergism between the carbonized RH and iron-oxide phases.

The Undeniable Potential of Thermophiles in Industrial Processes

Extremophilic microorganisms play a key role in understanding how life on Earth originated and evolved over centuries. Their ability to thrive in harsh environments relies on a plethora of mechanisms developed to survive at extreme temperatures, pressures, salinity, and pH values. From a biotechnological point of view, thermophiles are considered a robust tool for synthetic biology as well as a reliable starting material for the development of sustainable bioprocesses. This review discusses the current progress in the biomanufacturing of high-added bioproducts from thermophilic microorganisms and their industrial applications.

Enhancing the Physical, Antimicrobial, and Osteo/Odontogenic Properties of a Sol–Gel-Derived Tricalcium Silicate by Graphene Oxide for Vital Pulp Therapies

Objectives: This study developed a sol–gel tricalcium silicate/graphene oxide (TCS-GO) composite and examined its physicochemical properties, antimicrobial activity, and osteo/odontogenic effect on dental pulp stem cells. Methods: Tricalcium silicate was synthesized and combined with graphene oxide at three different concentrations, namely 0.02%, 0.04%, and 0.08% w/w, while tricalcium silicate and mineral trioxide aggregate served as controls. The setting time, compressive strength, pH, and calcium ion release of the composites were evaluated, as well as antimicrobial properties against Streptococcus mutans and Lactobacillus acidophilus. Additionally, the viability of dental pulp stem cells; apatite forming ability; and the gene expression of Alkaline phosphatase, Dentin sialophosphoprotein, and Runt-related transcription factor 2 were assessed. Results: TCS-GO (0.08%) showed a significantly shorter setting time and higher compressive strength when compared to MTA (p < 0.05). Additionally, tricalcium silicate and TCS-GO groups showed a higher release of Ca ions than MTA, with no significant difference in pH values among the different groups. TCS-GO (0.08%) also demonstrated a significantly stronger antimicrobial effect against Lactobacillus acidophilus compared to MTA (p < 0.05). ALP expression was higher in TCS-GO (0.08%) than MTA on days 3 and 7, while DSPP expression was higher in TCS-GO (0.08%) than MTA on day 3 but reversed on day 7. There was no significant difference in RUNX2 expression between TCS-GO (0.08%) and MTA on days 3 and 7. Conclusions: The TCS-GO (0.08%) composite demonstrated superior physicochemical characteristics and antimicrobial properties compared to MTA. Moreover, the early upregulation of ALP and DSPP markers in TCS-GO (0.08%) indicates that it has the potential to promote and enhance the osteo/odontogenic differentiation of DPSCs.

Machine learning-based prediction of cadmium pollution in topsoil and identification of critical driving factors in a mining area.

Mining activities have resulted in a substantial accumulation of cadmium (Cd) in agricultural soils, particularly in southern China. Long-term Cd exposure can cause plant growth inhibition and various diseases. Rapid identification of the extent of soil Cd pollution and its driving factors are essential for soil management and risk assessment. However, traditional geostatistical methods are difficult to simulate the complex nonlinear relationships between soil Cd and potential features. In this study, sequential extraction and hotspot analyses indicated that Cd accumulation increased significantly near mining sites and exhibited high mobility. The concentration of Cd was estimated using three machine learning models based on 3169 topsoil samples, seven quantitative variables (soil pH, Fe, Ca, Mn, TOC, Al/Si and ba value) and three quantitative variables (soil parent rock, terrain and soil type). The random forest model achieved marginally better performance than the other models, with an R2 of 0.78. Importance analysis revealed that soil pH and Ca and Mn contents were the most significant factors affecting Cd accumulation and migration. Conversely, due to the essence of controlling Cd migration being soil property, soil type, terrain, and soil parent materials had little impact on the spatial distribution of soil Cd under the influence of mining activities. Our results provide a better understanding of the geochemical behavior of soil Cd in mining areas, which could be helpful for environmental management departments in controlling the diffusion of Cd pollution and capturing key targets for soil remediation.

Maleic Anhydride-Derived Copolymers Conjugated with Beta-Lactam Antibiotics: Synthesis, Characterization, In Vitro Activity/Stability Tests with Antibacterial Studies

The synthesis and characterization of biocompatible three different maleic anhydride co-polymer conjugated with two different beta-lactam antibiotics at in vitro conditions were conducted. The polymer–drug conjugates were synthesized by coupling β-lactam antibiotics via amide bonds to the copolymer. In this work, six different drug-functionalized maleic anhydride copolymers (DFMACs) were synthesized by the chemical conjugation method. This method is based on the ring-opening reaction of the anhydride ring of the copolymer to form an amide bond linking the drug. The synthesized DFMACs were characterized by 1H NMR and FTIR/ATR spectroscopies and analyses were carried out by UV/VIS spectroscopy and Zeta-sizer instrument in detail with consecutive antibacterial tests. The existence of a newly formed amide covalent bond between the drug and the copolymer chains was confirmed by 1H NMR and FTIR/ATR studies. This is the first report on the application of the selected branched biodegradable polymeric matrices for the covalent conjugation of ampicillin and cefalexin. Optimum stability and activity conditions for the synthesized DFMACs were determined. Analyses were conducted under in vitro conditions including varying pH values and simulated body fluids as a function of time to obtain new drug delivery system candidates for the two different antibiotics.

Novel Starch-Modified NiCrMn-LDH-Based Composite for Photocatalytic Degradation of Reactive Orange 13

Water pollution has become a great challenge today. To address this problem regarding wastewater treatment by removing toxic synthetic dyes from wastewater, this research focused on the synthesis of a novel starch-modified NiCrMn-layered double hydroxide composite through the coprecipitation method and applied it as a photocatalyst for the degradation of reactive orange 13 dye. The synthesized photocatalyst was characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), point of zero charges (PZC), dynamic light scattering (DLS), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and Zeta potential techniques. These techniques revealed different characteristics of photocatalysts, like surface and structural properties. According to BET analysis, the final composite had 2.5 × 102 m2/g BET-specific surface area with a 45.56 nm pore radius value, and the overall composite found as mesoporous. Similarly, in DLS analysis, bare NiCrMn-LDH had 404 nm hydrodynamic size, which increased for the final starch composite up to 667 nm. Zeta potential value changed from −14.56 mV to 0.95 mV after the incorporation of starch with NiCrMn-LDH. They confirmed the incorporation of starch with trimetallic NiCrMn-layered double hydroxide (2:1:2). Starch association improved the properties of the photocatalyst like surface area. Different parameters like pH value, initial dye concentration, photocatalyst dose, hydrogen peroxide concentration, effect of sacrificial reagent, and effect of inorganic anions were studied for degradation of RO13. Overall, the photocatalysis process for RO13 followed pseudo-first-order kinetics. Photocatalytic degradation reactions for reactive orange 13 were conducted with an initial dye concentration of 10 mg/L, photocatalyst dosage of 20 mg/50 mL, and pH value at 3 in the presence of sunlight, resulting in an impressive degradation removal rate of 86.68%. This remarkable degradation ability of the photocatalyst for reactive orange 13 proves this composite was highly efficient.

The effects of drag models and operating condition on the simulation of photocatalytic degradation of pesticides in a fluidized bed reactor.

Fluidized bed reactor can enhance mass transfer and increase reaction rate. Numerical simulation helps to optimize fluidized bed reactors. The present paper models the photocatalytic oxidation of 2,4-dichlorophenoxy acetic acid in a fluidized bed reactor using the Eulerian-Eulerian model. The drag models have influences on the distribution of catalysts particles. The bed expands under the fluid flow and reaches a quasi-steady height at approximately 3s. The asymmetric distribution of catalysts with respect to the axis plane is predicted. The Gidaspow model predicts the nearly same bed expansion with the experimental data, whereas the Syamlal-O Brien model overestimates it. The simulation results at two pH values are in accordance with the experimental data. The removal in the continuous stirred tank reactor decreases with the increase in flow rate.

Graphene oxide-functionalized molecular beacon for real-time interference-free detection of Ki-67 mRNA in living cells

Molecular beacons (MBs) based on hairpin-shaped oligonucleotides are captivating owing to their capability to enable effective real-time detection of cytosolic mRNA in living cells. However, DNase in the nucleus and lysosome could induce the degradation of oligonucleotides in MBs, leading to the generation of false-positive signals. Herein, a graphene oxide (GO) nanosheet was applied as a nanocarrier for MBs to greatly enhance the anti-interference of the easily designed nanoprobe. Advantageously, the absorption capacity of GO for MBs increased with the decrease in pH values, providing the MB-GO nanoprobe with the ability to detect the expression of cytosolic Ki-67 mRNA without interference from DNase Ⅱ in lysosomes. Moreover, the size of GO nanosheets was considerably higher than that of the nuclear pore complex (NPC), which prevented nanoprobes from transition through the NPCs, thereby avoiding the generation of false-positive signals in the nucleus. Altogether, the present work affords a convenient approach for the successful detection of Ki-67 mRNA expression in the cytosol without interference from DNase Ⅰ/Ⅱ in the nucleus/lysosome, which may be potentially further applied for the detection of other cytosolic RNAs.

The stability of phycocyanin extracted from Arthrospira platensis against osmotic, acid, and temperature stress conditions

The main problem of using natural blue pigment of phycocyanin produced by Arthrospira platensis (spirulina) is its instability in the food matrix because of environmental stress. This study aimed to investigate the stability of phycocyanin under simulated conditions in food formulations against osmotic, acid, and temperature stress conditions. Thermal degradation constant (Dc) and half-life (t½) of phycocyanin extracted from Arthrospira platensis were analyzed using response surface methodology followed by a first-order kinetic reaction. The stability of phycocyanin was assessed under various temperature (50–98ºC), NaCl (0–2% w/w), and pH (4–7) values. Results showed that the stability of phycocyanin extracted from Arthrospira platensis is high at neutral pH and concentration of 1% (w/w) NaCl. The stability decreased with increase in temperature at ≥75°C. The highest stability of phycocyanin (the lowest Dc and the maximum t½ were 0.011 min-1 and 54.03 min, respectively) was achieved at 66.89°C, pH = 6.6, and NaCl of 0.40% w/w. According to processing conditions, content of phycocyanin required for a food matrix is successfully calculated by the response surface method. This research showed that phycocyanin is stable at thermal shock in a neutral pH medium and low content of NaCl (0.40% w/w).

Strong Vertical Piezoelectricity and Broad-pH-Value Photocatalyst in Ferroelastic Y2Se2BrF Monolayer.

With the development of miniaturized devices, there is an increasing demand for 2D multifunctional materials. Six ferroelastic semiconductors, Y2Se2XX' (X, X' = I, Br, Cl, or F; X ≠ X') monolayers, are theoretically predicted here. Their in-plane anisotropic band structure, elastic and piezoelectric properties can be switched by ferroelastic strain. Moderate energy barriers can prevent the undesired ferroelastic switching that minor interferences produce. These monolayers exhibit high carrier mobilities (up to 104 cm2 V-1 s-1) with strong in-plane anisotropy. Furthermore, their wide bandgaps and high potential differences make them broad-pH-value and high-performance photocatalysts at pH value of 0-14. Strikingly, Y2Se2BrF possesses outstanding d33 (d33 = -405.97 pm/V), greatly outperforming CuInP2S6 by 4.26 times. Overall, the nano Y2Se2BrF is a hopeful candidate for multifunctional devices to generate a direct current and achieve solar-free photocatalysis. This work provides a new paradigm for the design of multifunctional energy materials.

Constructing CoP/Ni2P Heterostructure Confined Ru Sub-Nanoclusters for Enhanced Water Splitting in Wide pH Conditions.

Developing efficient electrocatalysts for water splitting is of great significance for realizing sustainable energy conversion. In this work, Ru sub-nanoclusters anchored on cobalt-nickel bimetallic phosphides (Ru-CoP/Ni2P) are constructed by an interfacial confinement strategy. Remarkably, Ru-CoP/Ni2P with low noble metal loading (33.1µgcm-2) shows superior activity for hydrogen evolution reaction (HER) in all pH values, whose turnover frequency (TOF) is 8.7, 15.3, and 124.7 times higher than that of Pt/C in acidic, alkaline, and neutral conditions, respectively. Meanwhile, it only requires the overpotential of 171 mV@10mAcm-2 for oxygen evolution reaction (OER) and corresponding TOF is 20.3 times higher than that of RuO2. More importantly, the Ru-CoP/Ni2P||Ru-CoP/Ni2P displays superior mass activity of 4017mAmgnoble metal -1 at 2.0V in flowing alkaline water electrolyzer, which is 105.1 times higher than that of Pt/C||IrO2. In situ Raman spectroscopy demonstrates that the Ru sites in Ru-CoP/Ni2P play a key role for water splitting and follow the adsorption evolution mechanism toward OER. Further mechanism studies disclose the confined Ru atom contributes to the desorption of H2 during HER and the formation of O-O bond during OER, leading to fast reaction kinetics. This study emphasizes the importance of interface confinement for enhancing electrocatalytic activity.

Effect of soil conditioners based on geomimetic materials on plant growth in degraded soils: Poly(acrylic acid)/bentonite

Geomimetic materials (GEOMI) are composite materials based on polymer and clays, able to imitate structural and functional properties of soils, including their structure, cationic exchange capability (CEC), water uptake capability (WUC), pH buffering ability, immobilizing of substances, among other. Because they can be used to develop of fertilizer slow-release systems, they have been identified as a novel approach to advance toward a most sustainable agriculture. The aim of this work was to study the effect of GEOMI on the plant growth in degraded soils. For this, GEOMI-1.0 was synthesized using poly(acrylic acid) as model of humic substances and bentonite modified with trichlorovinylsilane as mineral fraction model. Materials were characterized by different techniques. GEOMI-1.0 showed a hybrid, homogeneous, and amorphous structure. In addition, it was thermally stable at below ⁓200 °C with a Tg about 49.3 °C, showed a high WUC (⁓1384 g of water per 100 g of material). Likewise, it was verified that GEOMI-1.0 can decreases the pH values and increases the CEC of degraded soils depending on the added amount of geomaterial; but also, the electric conductivity values showed no dependence on the added amount of GEOMI-1.0. By correlation analysis, an exponential dependence of CEC was observed respect to pH changes, the relative amount added of GEOMI-1.0 and the initial CEC. Finally, using Brachiaria Brizantha cv. Marandú as plant model, the increase in the biomass content of roots and leaves, and the number of germinated seeds, were observed when GEOMI-1.0 was used for restoration of in-lab degraded soils.

Effects of mixing water and environmental pH value on the properties of sulfoaluminate cement-based ultra-high water materials

In order to grasp the influence of the pH value of mixing water and environmental water on the properties of ultra-high water materials, this article separately carried out the influence of different pH values of mixing water on the properties of ultra-high water materials and the conservation of high-water materials in water environments with different pH values. Using test methods such as loss of flow time, compressive strength, Scanning Electron Microscope (SEM), X-Ray Diffraction (XRD), Thermogravimetric-Differential Thermal Analysis (TG–DTA), to conduct regular exploration and mechanism analysis. The study found that with the continuous increase of the pH value of the mixing water, the loss of flow time of the ultra-high water material gradually decreased, and the compressive strength of the samples at the same age continued to increase. A lower pH value will affect the compressive strength of the consolidated body of the ultra-high water material, but when the pH = 13 in the reaction solution, the compressive strength of the consolidated body will no longer increase and begin to produce a weakening effect. The pH of the construction water for ultra-high water materials is recommended to be 4–13. At the same time, it was found that under the conservation of an acidic environment, the consolidated body was severely eroded and the strength loss was large. The acid–base environment of the goaf suitable for filling with the ultra-high water material should be between pH = 7–10 to ensure that the filling body is not weakened by erosion.

Design and Preparation of Lifetime-Based Dual Fluorescent/Phosphorescent Sensor of pH and Oxygen and its Exploration in Model Physiological Solutions and Cells.

In the present report, a novel dual pH-O2 sensor based on covalent conjugate of rhodamine 6G and cyclometalated iridium complex with poly(vinylpyrrolidone-block-vinyltetrazole) copolymer is reported. In model physiological solutions the sensor chromophores display independent phosphorescent and fluorescent lifetime responses onto variations in oxygen concentration and pH, respectively. Colocalization studies on Chinese hamster ovary cells demonstrate the preferential localization in endosomes and lysosomes. The fluorescent lifetime imaging microscopy-phosphorescent lifetime imaging microscopy (FLIM-PLIM) experiments show that the phosphorescent O2 sensor provides unambiguous information onto hypoxia versus normoxia cell status as well as semi-quantitative data on the oxygen concentration in cells in between these two states. However, the results of FLIM measurements indicate that dynamic lifetime interval of the sensor (≈0.5ns between pH values 5.0 and 8.0) is insufficient even for qualitative estimation of pH in living cells because half-width of lifetime distribution in the studied samples is higher than the sensor dynamic interval. Nevertheless, the variations in rhodamine emission intensity are much higher and allow rough discrimination of acidic and neutral cell conditions. Thus, the results of this study indicate that the suggested approach to the design of dual pH-O2 sensors makes possible to prepare the biocompatible and water-soluble conjugate with fast cellular uptake.

Investigating Safety and Technological Traits of a Leading Probiotic Species: Lacticaseibacillus paracasei

Lacticaseibacillus spp. are genetically close lactic acid bacteria species widely used in fermented products for their technological properties as well as their proven beneficial effects on human and animal health. This study, the first to include such a large collection of heterogeneous isolates (121) obtained from international collections belonging to Lacticaseibacillus paracasei, aimed to characterize the safety traits and technological properties of this important probiotic species, also making comparisons with other genetically related species, such as Lacticaseibacillus casei and Lacticaseibacillus zeae. These strains were isolated from a variety of heterogeneous sources, including dairy products, sourdoughs, wine, must, and human body excreta. After a preliminary molecular characterization using repetitive element palindromic PCR (Rep-PCR), Random Amplification of Polymorphic DNA (RAPD), and Sau-PCR, particular attention was paid to safety traits, evaluating antibiotic resistance profiles, biogenic amine (BA) production, the presence of genes related to the production of ethyl carbamate and diaminobenzidine (DAB), and multicopper oxidase activity (MCO). The technological characteristics of the strains, such as the capability to grow at different NaCl and ethanol concentrations and different pH values, were also investigated, as well as the production of bacteriocins. From the obtained results, it was observed that strains isolated from the same type of matrix often shared similar genetic characteristics. However, phenotypic traits were strain-specific. This underscored the vast potential of the different strains to be used for various purposes, from probiotics to bioprotective and starter cultures for food and feed production, highlighting the importance of conducting comprehensive evaluations to identify the most suitable strain for each purpose with the final aim of promoting human health.

Characteristics of apricot yogurt fermented with different culture straıns and stevıa

This study evaluated the effects of exopolysaccharide (EPS)-producing and non-EPS-producing culture varieties and the enriching of apricot pulp to the post-acidification process and microbiological, viscosity, antioxidant, and sensory properties of yogurt. Two groups of yogurts were produced in terms of culture variety. One of the yogurts in both groups was enriched with apricot pulp at a ratio of 10%. The natural sweetener, stevia, was added at a ratio of 0.1% to all yogurts. The lowest pH and highest acidity values were determined for the non-EPS sample produced without apricot pulp. The dry matter content of the yogurts was increased with whey protein powder. Between the yogurts produced with EPS-producing strains, the bacteria counts were higher for those enriched with apricot pulp. The highest Streptococcus thermophilus counts were determined for the sample produced with EPS-producing culture and apricot pulp at the beginning and end of the storage. Total phenolic content (TPC) was higher for the samples produced with conventional culture and enriched with apricot pulp. Similar results were observed in the antioxidant activity. Sensory attributes were considered taste, odor, appearance, texture, and overall acceptability. The yogurts produced with EPS-producing culture were preferred regarding taste, texture, and overall acceptability.

Studies of Light Scattering by Hemoglobin Molecules under the Effect of Iron (III) Chloride and Various pH Levels

A lot of literature sources discuss diseases associated with the hemoglobin protein [1, 2]. In the modern world, more than 800 million people suffer from anemia [3]. Assessing the level of hemoglobin in the circulatory system is one of the ways to diagnose anemia. Hemoglobin protein is also a promising source of bioactive peptides [4]. The aim of the work was to identify the reasons leading to conformation changes of this protein. It still remains unclear what exactly causes disruption of its functionality. Human hemoglobin from Sigma H7379 was studied in the work; all experiments were conducted on a dynamic light scattering spectrometer — Photocor Complex. Experimental data were obtained using optical methods of static and dynamic light scattering. The work included an analysis of the behaviour of hemoglobin protein molecules in aqueous and aqueous-saline solutions with changes in solution parameters (pH, addition of iron chloride III). At values of pH< (3.56±0.15) and pH> (10.4±0.2), the hemoglobin molecule underwent conformational changes, resulting in the disintegration of the quaternary structure into αβ−dimers and individual α− and β−globules. As a result of the study, it was found that the addition of FeCl3 to aqueous solutions of hemoglobin increases the size and mass of scattering particles, which can be explained by the adsorption of Fe3+ ions on the protein surface. However, upon reaching a certain concentration of FeCl3, the pH of the solution was lowered to such an extent that it caused conformational changes in hemoglobin, leading to the disintegration of its quaternary structure. These results can be taken into account when creating medicinal drugs for the treatment of anemia and other diseases associated with the hemoglobin protein.