Plant Performance Research Articles

Development of optimization control system for chiller plant based on a predictive model with Multi Stack LSTM and Deep Learning Neural Network Multi Output

Net-zero emissions become necessary for every country, implementing energy efficiency is the way to achieve it. Released report by the International Energy Agency in September 2022 stated that energy efficiency and electrification are the main priorities for Indonesia in achieving NZE. Currently, more than 50 % of energy consumption in buildings is intended for cooling systems (chillers plants). Thus, energy efficiency in buildings cooling systems has great potential to help achieve NZE and support SDGs. This research is intended to find an optimization control system for chiller plant in order to reduce energy consumption of cooling system in building. The development of this optimization control system is based on predictive model with Multi Stack LSTM and Deep Learning Neural Network. This research developed four different optimization control system frameworks. Every developed framework then will be tested by carrying out simulation with Chiller Plant model. The important parameter was found by using correlation matrix. Based on the correlation matrix, it was found that the most influence parameter that affect chiller plant performance are Tcws and Twb. It leads developed Frameworks 1 become the best compared with others developed frameworks in this research, because it used Twb as a variable input in parallel with performance prediction. This developed framework has deficient error MAE, MSE, RMSE respectively 0.8079, 0.6527, 0.8079 and able to reduce energy consumption by 10.72 %.

Transcription factor AtNAC002 positively regulates Cu toxicity tolerance in Arabidopsis thaliana

Copper (Cu) is an essential micronutrient for plant growth and development, but environmental Cu pollution has become increasingly severe, adversely affecting both ecosystems and crop productivity. In this study, we identified the AtNAC002 gene as a positive regulator of Cu toxicity in Arabidopsis thaliana. We found that AtNAC002 expression was induced by Cu excess, and the atnac002 mutant was Cu-sensitive, accumulating more Cu than the wild-type. Additionally, atnac002 mutants exhibit reduced activities of antioxidant enzymes (SOD, POD, and CAT), leading to increased levels of reactive oxygen species and malondialdehyde, which decrease Cu resistance. AtNAC002 might play a role in vacuolar and mitochondrial Cu compartmentalization by regulating genes involved in Cu detoxification, specifically COX11 and HCC1. Furthermore, AtNAC002 was implicated in flavone and flavanol biosynthesis, with the atnac002 mutant showing reduced flavonoid content. Our findings suggest that AtNAC002 is integral to the regulation of Cu toxicity tolerance in A. thaliana. This knowledge is critical for advancing our understanding and offers potential molecular breeding targets to enhance plant performance under Cu excess, which is significant for improving global food security and forest restoration.

Mitigating water deficit stress in lemon balm (Melissa officinalis L.) through integrated soil amendments: A pathway to sustainable agriculture.

Lemon balm (Melissa officinalis L.) is a valuable medicinal plant, but its growth can be significantly impacted by drought stress. This study aimed to mitigate the adverse effects of water deficit stress on lemon balm biomass by integrating poultry manure compost, poultry manure biochar, NPK fertilizer, Trichoderma harzianum, Thiobacillus thioparus, and elemental sulfur as soil amendments. The experiment was conducted in a greenhouse using a completely randomized design with a factorial arrangement, consisting of three replicates. It included a water deficit stress factor at three levels (95-100%, 75-80%, and 55-60% of field capacity) and a soil amendment treatment factor with eleven different fertilizer levels. Treatments included control (no amendment), NPK fertilizer, poultry manure compost, poultry manure biochar, and combinations of these with T. harzianum, T. thioparus, and elemental sulfur under various water deficit levels. Water deficit stress significantly reduced photosynthetic pigments, gas exchange parameters, chlorophyll fluorescence, relative water content, and antioxidant enzyme activity, while increasing membrane permeability and lipid peroxidation in lemon balm plants. However, the integrated application of organic, biological, and chemical amendments mitigated these negative impacts. The combined treatment of poultry manure compost, poultry manure biochar, NPK fertilizer, T. harzianum, T. thioparus, and elemental sulfur was the most effective in improving the morpho-physiological properties (1.97-60%) and biomass (2.31-2.76 times) of lemon balm under water deficit stress. The results demonstrate the potential of this holistic approach to enhance the resilience of lemon balm cultivation in water-scarce environments. The integration of organic, biological, and chemical amendments can contribute to sustainable agricultural practices by improving plant morphological and physiological properties and plant performance under drought conditions.

Nanostructured materials as hazardous wastewater micropullutants: Sources, behavior, and impact on functional bacterial community of activated sludge

Unique properties of nanoscale materials make them attractive for industrial, medical, agricultural, and environmental applications. Nevertheless, the release of nanoparticles into the environment is a major concern due to the lack of knowledge about their behavior in the environment and potential widespread environmental impacts. On the one hand, nanomaterials are perceived as pollutants that may affect activated sludge microorganisms and, consequently, the efficiency of wastewater treatment processes. On the other hand, some nanomaterials can be intentionally added to activated sludge systems to improve their performance in terms of, e.g., sludge settling and removing heavy metals or organic pollutants. As a result, nanoparticles are frequently accumulated in wastewater, which is considered to be a major source of nanoparticle release to the surrounding environment. Processes that involve the action of activated sludge are used worldwide in wastewater treatment plants due to their excellent capacity of removing nutrients, degrading toxins, and retaining biomass. High concentrations of nanoparticles entering activated sludge systems can affect their growth and metabolism. The research studies, which are reviewed in the present article, show that nanoparticles significantly reduce the relative abundance of the activated sludge microbial community associated with nitrification, denitrification, and phosphorus removal. The knowledge about the structure of the activated sludge microbial community with an assessment of nanomaterial toxicity can contribute to optimizing the sludge population and improving the performance of wastewater treatment plants.

Experimental evidence that poor soil phosphorus (P) solubility typical of drylands due to calcium co-precipitation favors autonomous plant P acquisition over collaboration with mycorrhizal fungi

Calcareous dryland soils are rich in precipitated phosphate and represent >30% of Earth's land, yet the relative importance of phosphorus-acquisition strategies (PAS) among plant species in these systems is not well known. No experiment has investigated potential interactions between varying amounts of added calcium carbonate (CaCO3) and arbuscular mycorrhizal fungi (AMF) on plant performance and PAS which could test for potential mechanisms without the limitations of in-situ comparisons along natural gradients. To fill this knowledge gap, we conducted an experiment with CaCO3 addition, AMF inoculation, and three invasive and five native grassland plants. We expected an increase in soil [CaCO3] of an alkaline subsoil to 1) reduce soil-available phosphorus (P), 2) reduce plant biomass and P uptake, and 3) shift PAS toward increased root mining as Ca-bound P increases. The largest CaCO3 addition reduced available P by as much as 57%. On average, the largest addition of CaCO3 reduced total biomass of plants by 19% and plant uptake of P by 15%. The PAS seemed to have changed, and CaCO3 additions tended to increase an indicator of root exudation (shoot [Mn]) to mobilize Ca-bound P, suggesting plasticity for some inducible root mining, especially Artemisia frigida and Poa secunda. However, CaCO3 and plant species interacted to affect shoot [Mn]. The invasive grass Bromus tectorum was superior at acquiring P (> P uptake, > shoot [Mn]) and thus tolerating low soluble P conditions. Rarely did AMF and CaCO3 interact to affect plant biomass. When they did, mycorrhizal responsiveness did not increase where P was less available, suggesting AMF become less beneficial upon P and Ca coprecipitation. In dryland soils with less soluble P, plants are thus likely to rely more on root mining PAS than mycorrhizal scavenging, except for the invasive forb Euphorbia esula that always benefitted from AMF inoculation.

Morpho-Physiological and Biochemical Responses in Prosopis laevigata Seedlings to Varied Nitrogen Sources

Nitrogen (N) fertilization promotes morphofunctional attributes that enhance plant performance under stress conditions, but the amount and form supplied modify the magnitude of plant responses. We assessed several morpho-physiological and biochemical responses of Prosopis laevigata seedlings to a high supply of N, provided as either inorganic (NH4NO3) or organic (amino acids). Such N treatments were applied on four-month-old seedlings as a supplement of 90 mg N to a regular supply of 274 mg N plant−1. Nitrogen supply modified biomass allocation patterns between leaves and roots regardless of N form. Increased N input decreased photosynthetic capacity, even when plants had high internal N reserves. Organic N fertilization reduced the N use efficiency, but increased leaf and root amino acid concentrations. Proteins accumulated in stems in plants receiving inorganic N, while the organic N increased leaf proteins. High N supply promoted root starch accumulation irrespective of N form. Nitrogen supply did not directly influence plants’ regrowth capacity. Still, resprouting was correlated to initial root-to-shoot ratios and root starch, confirming the importance of roots as storage reserves of starch for recovering biomass after browsing. These findings have practical implications for designing nutritional management strategies in nurseries to improve seedling performance in afforestation efforts.

Effects of Corm Treatment with Cold Plasma and Electromagnetic Field on Growth and Production of Saffron Metabolites in Crocus sativus.

Crocus sativus L. is a widely cultivated traditional plant for obtaining dried red stigmas known as "saffron," the most expensive spice in the world. The response of C. sativus to pre-sowing processing of corms with cold plasma (CP, 3 and 5 min), vacuum (3 min), and electromagnetic field (EMF, 5 min) was assessed to verify how such treatments affect plant performance and the quality and yield of herbal raw materials. The results show that applied physical stressors did not affect the viability of corms but caused stressor-dependent changes in the kinetics of sprouting, growth parameters, leaf trichome density, and secondary metabolite content in stigmas. The effect of CP treatment on plant growth and metabolite content was negative, but all stressors significantly (by 42-74%) increased the number of leaf trichomes. CP3 treatment significantly decreased the length and dry weight of flowers by 43% and 60%, respectively, while EMF treatment increased the length of flowers by 27%. However, longer CP treatment (5 min) delayed germination. Vacuum treatment improved the uniformity of germination by 28% but caused smaller changes in the content of stigma compounds compared with CP and EMF. Twenty-six compounds were identified in total in Crocus stigma samples by the HPLC-DAD method, including 23 crocins, rutin, picrocrocin, and safranal. Processing of Crocus corms with EMF showed the greatest efficiency in increasing the production of secondary metabolites in saffron. EMF increased the content of marker compounds in stigmas (crocin 4: from 8.95 to 431.17 mg/g; crocin 3: from 6.27 to 164.86 mg/g; picrocrocin: from 0.4 to 1.0 mg/g), although the observed effects on growth were neutral or slightly positive. The obtained findings indicate that treatment of C. sativus corms with EMF has the potential application for increasing the quality of saffron by enhancing the amounts of biologically active compounds.

Evaluating sampling techniques for quantifying Asiatic garden beetle (Maladera formosae) (Coleoptera: Scarabaeidae) infestations in commercial mint.

The Asiatic garden beetle, Maladera formosae Brenske (AGB), has become a significant pest of commercial mint fields in northern Indiana. Larval feeding on mint roots can cause stunted growth and plant death when densities are high. Sampling approaches that provide reliable estimates of larval densities in mint have not been established, leaving farmers without the knowledge necessary to implement integrated pest management (IPM) strategies. To address this knowledge gap, we evaluated strategies for estimating AGB larval densities and plant performance in commercial mint systems. We used 2 sampling methods to collect larval density and plant performance data from 3 mint fields and conducted simulations to optimize sampling intensity (accuracy and precision) and sampling scheme (random vs. systematic) using these data. Additionally, we examined the sensitivity and efficiency of each sampling method. Compared to the cup-cutter method, the quadrat method provided the most accurate and precise estimates of larval density and plant performance, with ≤ 7 samples required per 0.2 ha. Quadrat excavation was also more sensitive, increasing the probability of detecting AGB larvae within a 32 m2 plot by 76.7%, and requiring significantly less time to survey an equivalent volume of soil for AGB larvae. When the quadrat method was employed, random sampling schemes provided below-ground biomass estimates that were significantly closer to the true mean of the sampling area. The results of this research will facilitate the development of IPM decision-making tools for farmers and support future research for AGB and other soil insect pests affecting mint production.

Plant native: comparing biodiversity benefits, ecosystem services provisioning, and plant performance of native and non-native plants in urban horticulture

AbstractPlant species used in urban horticulture are frequently non-native despite evidence that urban areas are regular points of introduction, often leading to invasions and negative impacts on biodiversity. Many horticulturalists assert that non-native plants are more successful and provide equal or greater habitat and ecosystem services than native plants. However, little research has compared native and non-native plants in urban systems. We present here a systematic literature review, using the PRISMA methodology, to assess three questions: (1) Is there a difference between native and non-native plants in their ability to support faunal biodiversity in urban green spaces? (2) Is there a difference between native and non-native plants in their provisioning of urban ecosystem services? 3)Do non-native species outperform natives in urban environments in terms of survival, growth, and fitness? We extracted data from 165 total papers. One hundred and twenty studies found that native plants outperform non-native plants on the response metric evaluated in the study, 57 demonstrated mixed impacts, 56 demonstrated no differences among plant origin, and 26 found non-native plants outperformed native plants. We found overwhelming evidence that native plants support higher faunal abundance and diversity than non-native plants in urban landscapes. Relatively few studies examined ecosystem services and plant performance, but we found that native plants support higher levels and diversity of ecosystem services and that many native plants can be used for horticulture, that is, they will survive and thrive in urban conditions. Native plants provide multiple ecosystem functions in urban greenspaces, supporting urban biodiversity and provisioning ecosystem services than non-native plant species and should be prioritized in urban horticulture activities.

Thermal Power Plant Performance Analysis by Estimating Boiler Efficiency via Indirect Method: A Case Study

The performance of power plants is very critical since it is directly related with operating and electricity production costs. Among the other different type of power plants, coal-fired ones have advantages such as reliability and low cost fuel. In this paper, a coal (lignite) fired thermal power plant having capacity of 160 MW is taken into consideration and the impact of condenser pressure, moisture content of lignite, excess air coefficient, efficiency of turbine pressure and heater numbers on power plant thermal efficiency is investigated. It is aimed to determine performance losses of each equipment by means of the thermodynamics and economic analysis. In this scope, it is expected that the power plant operator will be able to evaluate the reduction potential of equipment performance losses and ensure more effective use of the power plants by correctly planning the maintenance and rehabilitation needs and times. In the calculations, the boiler efficiency was determined with EN 12952-15 standard (indirect method) since this method has higher accuracy in coal fired boilers. It is seen that the condenser pressure and excess air coefficient increments have not significant impact on power plant efficiency compared to moisture content of lignite, excess air coefficient, efficiency of turbine pressure and heater numbers. The significant effect is observed for fuel moisture content which rises from 22% to 47% and the power plant efficiency falls from 40% to 28%. The variation of the power plant thermal efficiency in case of failure of heaters is investigated and the power plant efficiency has decreased from 40.17% to 36.09% when the pre-heaters are no longer in to be in use because of any reason. In addition, revenue losses are estimated for each main equipment efficiency reduction for better use of power plant capacities and electricity lowering production costs.

Reinforcement learning for heliostat aiming: Improving the performance of Solar Tower plants

Solar Tower (ST) systems use heliostats to concentrate solar radiation onto a tower-mounted receiver. Optimizing the aiming strategy for these heliostats over the receiver remains a critical challenge due to the dynamic nature of solar radiation and the need to maximize energy capture while ensuring operational safety. This paper introduces a novel, model-free deep Reinforcement Learning (RL) approach to optimize heliostat aiming strategies, utilizing the Soft Actor–Critic (SAC) algorithm. This advanced RL method enhances the traditional Actor–Critic framework with two neural networks. The proposal dynamically adjusts the aiming points across the receiver surface in real time, trying to improve the overall performance of the ST plant. The strategy was simulated and evaluated over a full operational year and compared with traditional methods. The results show an increase of more than 8.8% in yearly absorbed power, a significant improvement that directly enhances performance and contributes to better economic outcomes for the technology. This technique also eliminates the need for constant human intervention and is applicable to both existing and future plants.

The effects of geometric factors on power generation performance in solar chimney power plants

This research aims to create an admissible source for specifying the relation between the plant's output power and specified geometrical parameters unique to each simulated chimney dimension. In the current study, the solar chimney output power has been studied considering 49 solar chimneys, including different collector diameters, chimney heights, and chimney diameters. The study employs the Ansys-CFX to simulate the numerical model for the unsteady k-ε turbulent flow for a vast number of geometries. The obtained results indicate that the velocity as the main factor in generating the output power has significantly improved by elevating the collector radius. The output power increased up to 50 % by elevating the collector radius and around 30 % by enhancing the chimney heights which cause an increase in airflow, temperature differentials. Moreover, increasing the chimney height has generally ascended the power plant system. Among all geometrical parameters, chimney radius had the least impact on solar chimney performance. The results indicate that the best ratio between collector radius and chimney height is 6 %–10 % to achieve the optimized output power. Our findings were verified with the available experimental setups.

Performance analysis of refuse‐derived fuel gasification plant with carbon capture and storage for power, heating, and hydrogen production

AbstractAmong various waste‐to‐energy technologies, gasification is one of the most promising, because of high efficiency, feedstock flexibility, and carbon capture potential. This case study is focused on comprehensive analysis of integrated gasification combined cycle‐based plant with refuse‐derived fuel (RDF) as feedstock and carbon capture. As there are hardly any studies focused on simulation of waste gasification with carbon capture, most of which are lacking important process specifics, this study addresses existing research gap. Process flowsheets are developed in detail according to literature data for various process configurations and simulated in AspenPlus software, while obtained results on material and energy balance were used for estimation of plant efficiency and performance indicators. Waste generation data in Novi Sad, Serbia, were used for determination of RDF flowrate. Configurations include different syngas cleaning pathways, final products (power, heating, and hydrogen) and co‐gasification with coal. Cogeneration increases overall plant efficiency from 27%–36% (power production only) to 63%–76%. High net hydrogen efficiencies, around 58%, compensate lower power and thermal energy production in hydrogen‐based configurations. Overall, co‐gasification produces better results due to higher feedstock heating value. Obtained results will be used in further research for environmental and economic evaluation to provide multi‐level assessment of proposed processes.

A Biomass-based Carbon Negative Brayton-Rankine Coupled Cycle Employing MCFC, Gasification and Combustion Boiler

Biomass based plants with CO2 capture usually experience low efficiency, at the same time, have great potential of mitigating environmental damage due to climate change. In this work, unlike conventional power plants, a novel biomass-based carbon negative power plant has been conceived considering both biomass gasification and a biomass combustion boiler. CO2 capture and improved efficiency due to the unique integration of the plant components are the major expected outcome from the proposed plant model. The plant contains a steam cycle, an MCFC and an EFGT unit as the power producing blocks. A vital operating parameter i.e., biomass combustion boiler equivalence ratio () has been varied to witness the changes in performance of the plant. The net power generated by the plant seemed to be increasing with . The plant performs best when the plant is operated at a  value of 2.5. At this operating condition, the net power generated by the power plant found to be 13796 kW with 75.52 % efficiency and 0.3957 kg/kWh specific biomass consumption (SBC).

Thiourea Supplementation Improves Drought Stress Response of Ridge‐Sown and Mulch‐Applied Rainfed Maize (Zea mays L.) via Improved Leaf Source to Grain Sink Dynamics

ABSTRACTIn regions of South Asia where rainfed maize is grown, effective crop management during drought is essential for maximising yield. A variety of water‐conserving planting practices are used, and more recently, techniques such as foliar supplementation to maintain nutrients during drought have also shown promise. However, specific combinations of these approaches are often untested for optimality. Here, we explore the effects of two maize planting practices (ridge sowing and mulching) to conserve water, in combination with foliar thiourea. Drought stress response of crop was assessed at two experimental sites (L‐I and L‐II), through split‐plot design (main plots: flat sowing + mulch, flat sowing, ridge sowing + mulch [RS + M] and ridge sowing; sub‐plots: unsprayed, water spray, 500 ppm thiourea and 1000 ppm thiourea). Plant performance was assessed via dry matter accumulation, grain growth rate, stomatal parameters, grain yield, stover yield and nitrogen uptake. Rainfall breaks induced three dry spells during the pre‐anthesis and grain‐filling period. RS + M showed maximum drought tolerance by enhancing rainwater and nutrient use (N uptake [88.1 and 115.1 kg ha−1]) and recorded significantly higher periodic dry matter accumulation (149.2 and 156.8 g) along with higher 1000‐grain weight (181.0 and 196.6 g), grain‐filling duration (36.3 and 34.9 days) and leaf health parameters over the flat‐sown treatments. Furthermore, foliar supplementation of thiourea at 1000 ppm caused improved leaf health, likely through activation of a source to sink response (transfer of energy and materials from leaves to other plant organs) that alleviated moisture stress. Ultimately, the combination of RS + M and 1000 ppm thiourea led to the highest grain yields (32.1 and 39.5 qha−1).

Above- and below-ground field study on the impacts of conventional and alternative mesoplastics on Hordeum vulgare growth and soil invertebrate communities

Plastic plays an important role in agriculture, but its use has become a concerning source of pollution. While new (bio)degradable, alternative plastics are being developed and used as mulching films, their ecological impacts, in particular under field conditions, are not well understood. Furthermore, there is a notable lack of knowledge on how plastic pollution affects soil invertebrate communities. Most existing studies primarily focus on microplastics, often neglecting the impacts of mesoplastics. This study therefore compared the separate effects of two conventional (polyethylene and polypropylene) and two alternative (polyethylene containing biodegradable additives and compostable polylactic acid) mesoplastic films on plant performance (biomass, seed yield) and soil mesofaunal assemblages in a field experiment. The mesoplastics were applied at 0.1% (w/w), prior to soil being planted with Hordeum vulgare (spring barley), which was grown to maturity, for 11 weeks. Generally, there were no measurable differences between the conventional and alternative plastic treatments, however, barley exposed to mesoplastics showed reduced biomass, seed yield, and chlorophyll content, along with increased oxidative stress. Soil fauna, particularly Collembola, had lower richness and abundance when exposed to both plastic types, but assemblage structure and composition remained unchanged after 11 weeks. This study is pivotal in highlighting that both conventional and alternative plastics can similarly affect plant health and soil ecosystems. The evidence provided is essential for refining future risk assessments of agricultural plastic pollution and underscores the urgent need for more sustainable practices and materials in agriculture.

Thermal priming of Saccharina latissima: a promising strategy to improve seaweed production and restoration in future climates

Saccharina latissima is a brown algal kelp species of ecological and economic importance. As the rise in sea surface temperature will threaten not only wild populations of S. latissima but also the productivity of kelp farms, crop enhancement techniques will become crucial to mitigate this threat. Priming is a common strategy in crop plants, in which seeds are pre-exposed to moderate stress to improve the performance and tolerance of plants when exposed to harsher conditions. We investigated the potential of thermal priming to improve growth and tolerance of S. latissima. Kelp gametophytes primed at 20°C for 2, 4 and 6 wk and then re-transferred to 5°C were compared to a naïve treatment maintained at 5°C. Gametophyte priming increased growth of subsequently formed sporophytes by up to 30% (for 4 wk priming) compared to the naïve treatment. Female gametophyte growth in the priming environment was positively correlated to offspring sporophyte growth, indicating a maternal effect. Sporophytes were exposed to heat stress of 20°, 22°, 23° and 24°C for 2 wk. Sporophytes from 4 and 6 wk primed gametophytes exhibited 11 d longer tolerance at 22°C, 7 d longer tolerance at 23°C and 1°C higher thermal tolerance over 7 d compared to naïve sporophytes and sporophytes from 2 wk priming. A priming time of 4 wk was optimal for both sporophyte growth and thermal tolerance. Our results suggest that priming is a promising crop enhancement technique that could improve yield for seaweed farmers and restoration of kelp forests threatened by warming climates.

Role of organic amendments in improving the morphophysiology and soil quality of Setaria italica under salinity

Salinity negatively impacts soil fertility by impairing the development and physiological functions of foxtail millet plants. Organic amendments have emerged as a viable solution in the reclamation and management of salinity inflicted soils and improve the performance of crop. In this regard, a pot experiment was carried out to examine the effect of organic amendments (OAs) on soil quality and its influence on the growth and physiology of foxtail millet under saline and non-saline condition. The findings indicated that under salt stress conditions, the levels of proline, hydrogen peroxide (H2O2), and electrolyte leakage (EL) risen, whilst other physiological parameters decrease in foxtail millet. However, the addition of OAs, particularly dhaincha and biochar (BC), has shown a promising salt tolerant amendment among others. Its addition improved the growth performance of salinity-stressed plants, including plant height, fresh and dry biomass, simultaneously decreased sodium ion (Na+) and improved calcium (Ca2+), potassium (K+), and nitrate ion (NO3−). They also increased proline build up by 6–17 %, reduced H2O2 (19–38 %) and malondialdehyde (16–18 %). Furthermore, they elevated the relative water content (RWC) (25 %), chlorophyll content, and reduced EL (29–50 %). Once more, dhaincha and BC enhanced the number of rhizobia, phosphorus-solubilizing bacteria (PSB) and overall bacterial population in the soil. In saline soil, daincha and BC could enhance soil organic matter (628 %), total nitrogen (1630 %), available phosphorus (32–38 %), and exchangeable potassium (54–73 %). A potential strategy for improving setaria italica performance under salt is suggested to be the following order, dhaincha > biochar > vermicompost > duckweed. The study would assist stakeholders in these salinity-prone areas in strategizing the use of OAs to their fallow land for cultivation and agricultural activities.

Pilot scale on-site demonstration and seasonality assessment of nitrogen recovery and water reclamation from pig's slurry liquid fraction

Livestock slurry has gathered significant interest as a secondary raw material for fertilisers industry due to its content on macronutrients -nitrogen, phosphorous, and potassium- and organic carbon. In this study, the performance of an on-site pilot plant composed by microfiltration, membrane-assisted stripping, and reverse osmosis for selective recovery of nitrogen as fertiliser and water reclamation was demonstrated for 2 years in a pig farm, referenced to 8 batches for seasonal assessment. Microfiltration mitigated the seasonal variation in the composition of pig slurry leading to stable process efficiency in the following steps. Membrane-assisted stripping resulted in the recovery of up to 56% of nitrogen as high-purity ammonium sulphate, and up to 42% of reclaimed water as reverse osmosis permeate. The proposed train of technologies reported proper performance and robustness during the whole demonstration period as it resulted in the production of reclaimed water and ammonium sulphate with no significant quality variations. The energy cost for both products obtained in this study was found in the average of the previous works reviewed with 12.49 kWh kg−1 NH3 produced, and 0.37 kWh m−3 of reclaimed water. The environmental assessment showed that nitrogen losses could be reduced by up to 90 kg N ha−1 d−1 by replacing manure spreading with precise fertilisation techniques, enabled by the selective recovery of nitrogen from SLF. Finally, the financial study showed that the scaling up of the proposed train of technologies would result in benefits for farms with more than 1600 pig heads.

Seasonal acclimation of photosynthetic thermal tolerances in six woody tropical species along a thermal gradient

Abstract Extreme heat events are becoming increasingly common, and the short‐term acclimation of photosynthesis will have a large impact on plant performance. Trees in lowland tropical forests, which are hypothesized to have limited abilities to tolerate rising temperatures, may need to rely on short‐term acclimation of their more plastic traits, like photosynthetic thermal tolerance, to persist in the face of increasingly variable climates. Here, we investigated seasonal acclimation of thermal tolerances in plant species of the moist Amazon. Specifically, we measured the photosynthetic thermal tolerances of six common woody Amazonian species at the beginning and at the end of the dry season to determine the species' abilities to acclimate to intra‐annual changes to climate. In addition, we used the natural thermal gradient present at our research site to test the acclimation of individual plants to maximum air temperatures not currently observed elsewhere in the moist lowland Amazon (up to ~43°C). Between seasons, there were significant overall increases in the thermal tolerances of three species (i.e. higher thermal tolerances in the hotter dry season), suggesting that leaf megathermy is prominent in these species. Also, three species acclimated their thermal tolerances to microsite‐level differences in seasonal temperature maxima, suggesting closer fidelity between leaf and air temperatures (i.e. limited homeothermy) for these species. Our results show that some woody species from the moist Amazon can acclimate their thermal tolerances over short time‐scales, although acclimation is likely insufficient to overcome thermal stress during extreme temperature events. Some species may therefore be more sensitive to heatwaves than others, which could impact survival and composition of tropical lowland forests into the future. Read the free Plain Language Summary for this article on the Journal blog.