Paraffin Oil Research Articles

Impact of Xanthan Gum on Stability and Rheological Properties of Multiple Emulsions Type Water-in-Oil-in-Water

The aim of this study was to improve the stability and rheological properties of water-in-oil-in-water (W/O/W) multiple emulsions containing 30 wt% paraffin oil, and 4 wt% polyglycerol-3-polycinoleate (PGPR) as a lipophilic surfactant. This was done by adding different concentrations of xanthan gum (GX) and the hydrophilic surfactants (Polyoxyethylene (80) sorbitan monooleate (Tween® 80), poloxamer 407(Lutrol® F127) using the emulsification in a two-steps process. The stability of the W/O/W multiple emulsions was analyzed over one-month storage period using physicochemical and rheological measurements. An excellent structure appeared with 0.175 wt% of xanthan gum in the outer aqueous phase and 1 wt% of Tween® 80. The modified Cross model was successfully applied to fit the flow curves of multiple W/O/W emulsions at different concentrations of xanthan gum. The incorporation of xanthan gum in a concentration range of 0.05-0.175 wt% induced an increase in the yield stress, in the zero-shear rate viscosity, and in the infinite shear rate viscosity of the multiple emulsions. The study also showed that adding xanthan gum in a concentration range of 0.05-0.175 wt% to W/O/W emulsions caused an increase in the viscosity of the system in the Newtonian regime and viscoelastic behavior.

Encapsulation of Methanotrophs within a Polymeric Matrix Containing Copper- and Iron-Based Nanoparticles to Enhance Methanol Production from a Simulated Biogas.

The production of renewable energy or biochemicals is gaining more attention to minimize the emissions of greenhouse gases such as methane (CH4) and carbon dioxide for sustainable development. In the present study, the influence of copper (Cu)- and iron (Fe)-based nanoparticles (NPs), such as Cu, Fe3O4, and CuFe2O4, was evaluated during the growth of methanotrophs for inoculum preparation and on the development of a polymeric-matrix-based encapsulation system to enhance methanol production from simulated biogas (CH4 and CO2). The use of simulated biogas feed and the presence of NP-derived inoculums produce a remarkable enhancement in methanol production up to 149% and 167% for Methyloferula stellata and Methylocystis bryophila free-cells-based bioconversion, respectively, compared with the use of pure CH4 as a control feed during the growth stage. Furthermore, these methanotrophs encapsulated within a polymeric matrix and NPs-based systems exhibited high methanol production of up to 156%, with a maximum methanol accumulation of 12.8 mmol/L over free cells. Furthermore, after encapsulation, the methanotrophs improved the stability of residual methanol production and retained up to 62.5-fold higher production potential than free cells under repeated batch reusability of 10 cycles. In the presence of CH4 vectors, methanol production by M. bryophila improved up to 16.4 mmol/L and retained 20% higher recycling stability for methanol production in paraffin oil. These findings suggest that Cu and Fe NPs can be beneficially employed with a polymeric matrix to encapsulate methanotrophs and improve methanol production.

Simulating dispersion of oils from a subsea release comparing mechanical and chemically enhanced dispersion — An experimental study of the influence of oil properties

The main objective with subsea mechanical dispersion (SSMD) is to influence the fate of an oil spill in the marine environment by significantly reducing oil droplet sizes from subsea release of oil. Earlier studies have indicated that the capability of SSMD to reduce oil droplet sizes is comparable to subsea dispersant injection (SSDI).Earlier testing of SSMD has mainly used a low viscus paraffinic oil. Focus for this study was to study SSMD and SSDI effectiveness using five oil types spanning out a wide variation of relevant oil properties. Effectiveness was quantified as the reduction in oil droplet sizes measured by a Silhouette camera. Testing of the two technologies were completed in the same experiment on a simulated subsea release.The results show a variation in effectiveness for both technologies as a function of oil properties. SSMD and SSDI showed comparable effectiveness for all oils tested.

Lipid Nanoparticles for Lutein Encapsulation and Delivery

Recently, lipid nanoparticles have been intensively studied as carriers of lipophilic drugs. In this work, we have studied the stability of nanoemulsions with paraffin oil, solid lipid nanoparticles with stearic acid, and nanostructured lipid particles with paraffin oil and stearic acid in a mass ratio of 1 : 1. The obtained results have shown that all studied lipid systems stabilized with nonionic surfactants Tween 60 and Span 60 were stable to aggregation and subsequent sedimentation for more than 30 days. The incorporation of lutein into the lipid particles has almost no effect on their stability, while the size of solid lipid nanoparticles and nanostructured lipid nanoparticles decreases from 28–30 to 15–17 nm. The bioavailability of lutein loaded in lipid nanoparticles is evaluated from their effect on the restoration of blood flow velocity by simulating hemic hypoxia. Almost immediately after the application of lipid nanoparticles, the blood flow velocity ceases to decrease, and a tendency to its restoration is observed in 5–10 min. This shows that lipid nanoparticles with paraffin oil and stearic acid are promising candidates for the delivery of lipophilic drugs.

Effect of polyaniline doped with dodecylbenzene sulfonic acid on pour point depressant of waxy crude oil

The production, transportation, and storage of the crude oil below or near its pour point require a deep realizing the physical, chemical properties, and operating conditions of crude oil. Out of all the methods available for pumping waxy crude oil, the use of pour point depressant (PPD) is preferred economically. Chemical oxidative polymerization of polyaniline (PANI) doped with dodecylbenzene sulfonic acid (DBSA) was prepared and applied as a PPD for paraffinic crude oil. The prepared polymer was characterized using Fourier transform infrared, UV–Visible spectroscopy, photomicrographic analysis, and scanning electron microscope (SEM). It was found that the pour point of paraffinic crude oil reduced from +42 °C to −6 °C by treating this oil with 2500 ppm of PANI-DBSA dissolved in the heavy naphtha (PONA). This result was attributed to the innovative solvent (PONA) and represents a new achievement. In addition, the value of the crystallinity index of the paraffinic crude oil decreased from 80% to 74.7% after the addition of the PANI-DBSA. The conclusion is that the pour point of paraffinic crude oil decreases with decreasing the crystallinity index. This was mainly attributed to the effect of the polar groups of the prepared pour point depressant.

Effects of ultrasonic oscillations on permeability of rocks during the paraffinic oil flow

The paper shows that depending on the degree of blockage of the pore space due to paraffin precipitation the ultrasonic treatment has different effects. If a part of permeable channels is irreversibly deteriorated, then the activation of elastic oscillations contributes to postponing the moment of blocking the remaining part and helps to maintain the oil flow through a sample at a constant level. Without additional means an ultrasonic treatment does not have a significant effect in the case of strong blockage of permeable channels. If elastic oscillations are imposed on the rock and liquid at the initial moment of flow, then the porous space of the rock will be preserved from the precipitation of paraffins.

Nanoemulsions and Solid Lipid Nanoparticles with Encapsulated Doxorubicin and Thymoquinone

Nanoemulsions (NEs) and solid lipid nanoparticles (SLNs) are promising drug delivery systems. In this work, paraffin oil NEs and stearic acid SLNs stabilized with Tween 60 and Span 60 have been studied. NEs with an average droplet diameter of ~50 nm and suspensions of SLNs with an average size of ~30 nm are stable to aggregation for more than 90 days. The rates of penetration of lipid particles into cancer cells (C6 and MCF-7) depend on their sizes. After incubation for 1 h, lipid nanoparticles ~50 nm in size penetrate into cells, are distributed in their internal space, and concentrate in the nuclei. The cytotoxicity of doxorubicin- or thymoquinone-loaded NEs and SLNs against MCF-7 and HTC 116 cell lines is higher than the cytotoxicity of the individual substances. Wherein, unloaded NEs and SLNs show low cytotoxicity. The obtained results demonstrate that paraffin oil NEs and stearic acid SLNs are promising to be used as carriers of both lipophilic and amphiphilic drugs, including doxorubicin and thymoquinone. The accumulation of lipid nanoparticles with sizes smaller than 100 nm in cell nuclei is an advantage of such systems for the delivery of anticancer drugs, because this leads to DNA replication suppression followed by cell apoptosis.

Effect of Glycerol as Processing Oil in Natural Rubber/Carbon Black Composites: Processing, Mechanical, and Thermal Aging Properties.

The present work aims to study the effect of glycerol as a replacement for mineral oils in natural rubber (NR) composites to obtain suitable properties via cure characteristics, mechanical properties, and thermal stability. Glycerol was used at a 5 phr rate in the compound with carbon black as a reinforcing filler and was compared to mineral processing oils such as aromatic oil, treated distillate aromatic extracted oil, and paraffinic oil. Compared to the other oils, glycerol exhibits better maximum torque and torque differences. Also, a shorter scorch time, cure time, and a higher cure rate index of the compounds were observed. However, although the received mechanical properties, including tensile strength, elongation at break, and compression set of the vulcanized rubber using glycerol showed slightly lower values than the others, the 100% and 300% moduli, as well as the hardness of the composites filled with glycerol, exhibit better values relative to the other commercial oils. These findings demonstrate that glycerol overall presents a good balance of properties, making it beneficial to use glycerol as a substitute for mineral oil in tire, shoe sole, and rubber stopper applications.

Magnetic non-destructive evaluation of microstructural and mechanical characteristics of hardened AISI H13 die steel upon sustainable grinding

This paper describes the potential of non-destructive techniques such as micro-magnetic Barkhausen noise (MBN) to assess the grinding burn flaws in terms of microstructural and mechanical indices of hardened AISI H13 die steel. To overcome this grinding burn issue, minimum quantity lubrication grinding with eco-friendly machining fluids like paraffin oil (PO) and castor oil (CO) was adopted and compared its performance with well-established conventional grinding like wet and dry. Ground surface integrity with castor oil (CO) was found to be significantly improvement in surface quality including lower surface roughness (Rα: 0.23 μm and Rz: 1.83 μm) with uniform surface topography, absence of oxidization and carbonization film, and negligible change in microhardness and microstructure. The reason is strong and uniform anti-friction and anti-wear tribo-film was produced by castor oil, which minimizes heat penetration through limited ploughing and rubbing action. The MBN outcome i.e., root mean square (RMS) has followed a linear relation with microhardness and temperature of the ground sample with a correlation coefficient of 0.993 and 0.981. Besides, lower amplitude and wide peak envelope get shifted towards a higher magnetic field in the MQL-CO grinding caused by poor thermal softening effect on the ground sample, which restricts magnetic domain wall movement and rotation. These outcomes could guide tooling industries for efficient sustainable grinding with faster thermal damage assessment, which helps to minimize production cycle time and back to clean environment.

Rosmarinus officinalis Essential Oil Increases Hair Length and Follicle Diameter of Ultraviolet B-exposed Mice Through VEGF

BACKGROUND: Ultraviolet (UVB) radiation induces hair photoaging by triggering oxidative stress, causing alterations in hair diameter and length, which contribute to the development of senile alopecia. Development of alternative anti-photoaging agents to prevent hair loss from various materials, including natural products, is currently being explored. Rosmarinus officinalis essential oil (ROEO) has been known to have antioxidant and vasodilation properties. However, the effect and mechanism of ROEO on UVB-exposed hair are still unclear. Therefore, this study was conducted to evaluate the effects of ROEO on the hair length and follicle diameter in UVB-exposed mice as well as the skin vascular endothelial growth factor (VEGF) level.METHODS: Thirty male Swiss mice were treated topically with/without paraffin oil, 2% minoxidil, or various concentrations of ROEO, every day for 21 days. Meanwhile, UVB exposure was performed 3×/week. On day 21, the hair length was measured, the skin tissue was collected for hair follicle diameter and VEGF measurements.RESULTS: ROEO contained phenolic, including flavonoids and tannins, as well as non-phenolic antioxidants, including 1.8-cineole, α-pinene, and camphor. The IC50 value of ROEO was 15.977 ppm. Significant higher hair length, follicle diameter, and VEGF level of 10% ROEO+UVB-treated mice were observed, compared with the ones of mice exposed with UVB merely (LSD test, p<0.05).CONCLUSION: Since 10% ROEO could significantly increase hair length, follicle diameter and VEGF level, and contained antioxidant compounds, it can be suggested that ROEO might increase hair length, follicle diameter, and VEGF level through its antioxidant component.KEYWORDS: Rosmarinus officinalis, hair follicle diameter, hair length, VEGF, ultraviolet B, antioxidant

Structure evolution of fluorapophyllite-(K) under high pressure

ABSTRACT The high pressure structural evolution of a natural fluorapophyllite-(K) K0.70(NH4)0.20 Ca3.97Na0.07[Al0.04Si7.96O20]F0.99·(H2O)8.05, Z = 2, a = 8.9757(2), c = 15.7920(2) Å, space group P4/mnc, from Nidym river, East Siberia, Russia, compressed in penetrating (ethanol:water 4:1 mixture) and non-penetrating (paraffin oil) media up to 4.7 GPa, was studied by single-crystal X-ray diffraction with a diamond anvil cell. The compressibility is identical in both media. At the initial stage the compression proceeds mainly within the plane (xy) and less along the z-axis; above 3 GPa the compression becomes almost isometric. Within the whole pressure range there are no signs of the symmetry lowering. The main pressure-induced effect on the tetrahedral layer consists in a cooperative rotation of the 4-fold rings, which provides the structure compression within the (xy) plane. The compression along the z-axis proceeds through the shortening of the interlayer distance, whereas the thickness of silicate layer remains almost unchanged.

Effects of single-dose and co-supplementation of vitamin D and omega-3 on metabolic profile in women with polycystic ovary syndrome: An RCT.

Polycystic ovary syndrome (PCOS) is a heterogeneous medical condition with a cluster of metabolic and endocrine disorders including dyslipidemia, insulin resistance, and hyperandrogenism. The present study aimed to determine the effects of single-dose and co-supplementation of vitamin D (vit D) and omega-3 (O3) on anthropometric and several biochemical factors in women with PCOS. In this double-blind, randomized clinical trial, 80 PCOS women referred to Shahid Motahhari Clinic, Shiraz, Iran, from April to October 2017 were studied in 4 groups (n = 20/each) for 8 wk. The placebo group received the placebo capsule (paraffin oil); 1 weekly and 2/daily; the vit D group received vit D (50,000 IU/weekly) + 2 placebo capsules daily, O3 group, 2, O3 capsules daily + 1 placebo capsule weekly, and vit D + O3 (50000 IU/weekly vit D + 2, O3 capsules daily). Before and after 8 wk of intervention, height, weight, body mass index, waist circumference, triglycerides, total cholesterol (TC), high-density lipoprotein cholesterol, low-density lipoprotein cholesterol, fasting blood sugar, homeostasis model of insulin resistance index, and sex hormone binding globulin were compared between groups. The significant reduction was detected in serum triglyceride (p = 0.002), TC (p = 0.04), fasting blood sugar (p = 0.02), insulin (p = 0.001), and homeostasis model of insulin resistance index (p = 0.001) concentrations in all vit D, O3, and vit D + O3 supplemented groups compared to the placebo group. Furthermore, in comparison with the placebo group, a significant increase was observed in serum sex hormone binding globulin levels after vit D, O3, and vit D + O3 treatments. Nevertheless, no significant changes were observed in serum high-density lipoprotein cholesterol, low-density lipoprotein cholesterol, and anthropometric indices in all treated participants. The current study indicated that single dose and co-supplementation of vit D and O3 for 8 wk was associated with beneficial effects on serum triglyceride, TC, insulin, and sex hormone binding globulin concentrations among women suffering from PCOS.

New stochastic devices for simultaneous analysis of mismatch repair proteins and KRAS in biological samples

Two stochastic microsensors based on the immobilization of inulins: inutec and frutafit in a paste obtained from a graphene decorated with nitrogen (10.8 %), and boron (2.6 %), and paraffin oil (IR purity) were designed, characterized and validated for the molecular recognition and analysis of mismatch repair proteins like MLH1, MSH2, MSH6, PMS2, and of KRAS in biological samples such as: whole blood, urine, saliva, and tumoral tissues. The sensor based on inutec exhibited the largest working concentration range (10 decades of concentration) and the lowest limit of determination (0.32fg mL−1) when used for the assay of MLH1, and the wider working concentration range (8 decades of concentration), and the lowest limit of determination (2.30fg mL−1) when used for the assay of MSH6. The sensor based on frutafit exhibited the largest working concentration range (10 decades of concentration) when used for the determination of KRAS, and the wider working concentration range (5 decades of concentration), and the lowest limit of determination (1.00fg mL−1) when used for the assay of PMS2. No influence of the modifier (inutec and frutafit) was recorded on the linear concentration range (10 decades of concentration), and on the limit of determination (1.00 fg mL−1) for the assay of MSH2. The recoveries of MLH1, MSH2, MSH6, PMS2, and of KRAS in whole blood, urine, saliva, and tumoral tissues were higher than 98.00 with RSD (%) values lower than 0.10 %.

Prospective use of a cell‐free supernatant from the biosurfactant‐producing marine Planococcus maritimus SAMP MCC 3013 for oil removal and enhanced oil recovery

AbstractThe cell‐free supernatant (CFS) of the biosurfactant (BS) producing pure strain of Planococcus maritimus SAMP MCC 3013 was used for enhanced oil recovery (EOR). An indigenous marine culture of P. maritimus was grown in mineral salt medium (MSM) supplemented with glucose (1%) (w/v) (30°C, 120 rpm, 7 days). CFS was used to demonstrate its application for oil recovery through three assays: pumice stone, saturated gravel, and the glass beads‐packed column. The recovery of light paraffin oil was ∼40% in the pumice stone assay and ∼43% in the oil‐saturated gravel assay, respectively. The glass bead column demonstrated ∼42% of additional 2T engine oil recovery by CFS. Our study showed that BS containing CFS from P. maritimus SAMP MCC 3013 has the ability to recover oil in its crude form without using any sophisticated purification techniques. All three methods operated by us are harmonizing with each other with respect to the findings. Those methods can be employed in large scale operations for the bio‐recovery of oils using an environmentally friendly approach through the functional properties of BS. This is most likely the first report describing the use of a glass bead pack column for EOR applications particularly from Planococcus sp. These results are symbolic of prospective applications of BS containing CFS from indigenous P. maritimus SAMP MCC 3013 under ex‐situ conditions.

Recent Progress in Electrically Conductive and Thermally Conductive Lubricants: A Critical Review

Electrically as well as thermally conductive lubricants have drawn considerable attention and are an emerging research topic because they have unique advantages and advanced lubrication performance over traditional lubricants such as corrosion protection and efficient heat dissipation. For instance, some components of electric vehicles (EVs) such as bearings, seals, pads and gears require conductive lubricants to avoid premature failure and electromagnetic interference (EMI) problems due to induced shaft voltages and currents. This review provides a comprehensive overview of the recent developments in conductive lubricants. The review focuses on the important aspects to enhance the thermal and electrical conductivities as well as the tribological behavior (COF, and wear rate) of conductive solid, semisolid, and liquid lubricants. The lubricants that are electrically and thermally conductive with superior tribological performances have been identified through extensive literature review and presented in tabular form. This review summarizes the effect of various additives used to improve the conductive properties of the lubricants, such as polyalphaolefin oil, hydraulic oil, paraffin oil, and mineral oil. Furthermore, the review discusses the lubricating mechanism of conductive solid and liquid lubricants to facilitate a deeper understanding. Finally, the future perspectives and the research directions for conductive lubricants are also addressed.

Effects of synthesis parameters on the performance of crosslinked Co-polymers with clays for conformance control

Conformance control or water shut-off is a technique used to improve oil recovery. During conformance control, polymers block high permeability water areas and redistribute water drive toward unswept oil zones. In this study, co-polymers (denoted ATP-PGV/AM-co-AMPS) were synthesized using acrylamide (AM) and 2-acrylamide-2-methylpropane sulfonic acid (AMPS) as the monomers, polyethylene glycol (PEG)-200 and methylenebisacrylamide (MBA) as the crosslinkers, attapulgite (ATP) and bentonite (PGV) as the clay types, and ammonium persulfate (APS) as the initiator, in addition to paraffin oil and surfactants. Samples were synthesized using inverse emulsion polymerization with different concentrations of monomers, crosslinkers, and clays, and they were characterized using Fourier-transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX). FTIR spectra of the samples confirmed the existence of sulfonate and hydroxyl groups, which are important for polymer swelling. SEM-EDX images indicated that the morphology and elemental composition were different before and after swelling, confirming the occurrence of swelling. Moreover, samples were placed in sodium chloride solution (20,000 ppm) for 7 days to evaluate swelling at both room temperature and 90 °C. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) were used to determine the thermal characteristics of the microparticles. Finally, rheological measurements were used to assess the deformation and rheological behavior of the hydrogels. The results showed that after 1 day, good swelling without loss of mechanical strength was achieved with the composite synthesized using 10% AM, 15% AMPS, 6% PGV, and 10% ATP.

Management of Uremic Xerosis and Chronic Kidney Disease (CKD)-Associated Pruritus (CKD-ap) With Topical Preparations: A Systematic Review and Implications in the Indian Context.

Uremic xerosis and chronic kidney disease (CKD)-associated pruritus (CKD-ap) are the most commonly occurring dermatological problems faced by most of the CKD patients on hemodialysis which are not only annoying and draining to the patients but also have an intense effect on patients' quality of life. ThePubMed, Scopus, Google Scholar, and Web of Science databases were searched for the literature with the following search terms: uremic xerosis OR CKD-apOR uremic pruritusAND topical therapy OR topical ointment OR natural oil from the year 2002 -2022, and finally, 22 articles were chosen to write this review. Out of 22 studies, six used pharmacological preparations and remaining 16 studies used natural oils and components. All the articles were experimental studies (Pre/Quazi/RCT/True experimental) focusing on managing itch and xerosis associated with CKD and hemodialysis by topical application. The topical agents tried in various research studies are effective in managing itch and xerosis associated with CKD. They are safe, easy to use, and without allergic reactions. Natural oils like almond, chia seed, clove, glycerin, paraffin, and virgin coconut oil are readily available in home-care settings and can be used as a nurse-led intervention.Topical preparations for uremic xerosis and pruritus are effective, safe, and easy to apply on large body surface areas without systematic side effects. Natural oil-based topical preparations are cost-effective, safe, and easy to use.

Effect of digestible versus non-digestible citral nanoemulsions on human gut microorganisms: An in vitro digestion study

Essential oil (EO) nanoemulsions have been recently studied due to their antimicrobial properties. Nevertheless, little is known about their possible negative effect against human gut microorganisms during their passage though the gastrointestinal tract. This work studied the effect of digestible (corn oil) or non-digestible (paraffin oil) citral nanoemulsions against specific microorganisms of human microflora under in vitro digestion conditions. The use of a citral lipid carrier (paraffin oil or corn oil) decreased the nanoemulsion particle size and increased its stability after gastric conditions with regards to the pure citral nanoemulsions. Digestible nanoemulsions formulated with corn oil and citral presented a lower bactericidal activity against Lactobacillus acidophilus and Escherichia coli after being subjected to in vitro digestion conditions in comparison to the initial nanoemulsion. However, a non-digestible nanoemulsion formulated with paraffin oil and citral presented a similar antimicrobial activity against L. acidophilus and E. coli to the one of the initial nanoemulsion. This evidences that non-digestible nanoemulsions may entrap the citral in the lipid core and thus retaining its antimicrobial potential during their passage though the gastrointestinal tract. Hence, this work evidences the impact of the lipid carrier digestibility when formulating antimicrobial nanoemulsions on certain intestinal probiotic bacteria.

Nano-emulsification method as a strategy for oil soluble corrosion inhibitor transform to water soluble

Corrosion inhibitor is one of the most economical and effective approaches to protecting metal pipes in the oil and gas industries. However, a great amount of corrosion inhibitors such as imidazoline, are difficult to distribute fast due to their poor solubility or dispersibility in water, which results in inhomogeneous concentration distribution and ineffectiveness. In this study, nano-emulsification technique was developed to improve the dispersity of mercaptoacetic acid-modified oleic imidazoline (MOI) in corrosive water. The formulation of nanoemulsion is optimized with the phase inversion temperature (PIT) and droplet diameter. The prepared nanoemulsion which the hydrophilic lipophilic balance value (HLB) was 11.5 and the loading of corrosion inhibitor was 20 wt% exhibited remarkable water dispersion performance and its mean particle size was less than 100 nm. Moreover, its dispersion performance in water was significantly better than that of the paraffin oil system, and was similar in the ethanol system. The inhibition performances and mechanisms of nanoemulsion for L245 carbon steel in the H2S/CO2 containing 5.0 wt% NaCl solution were investigated with weight loss measurements and electrochemical tests. In terms of inhibition efficiency, the corrosion inhibitor encapsulated in nanoemulsion was exceeding 90%, which was comparable to the system employing ethanol and liquid paraffin as solvents. Further experimental results indicated that the nanoemulsion system was more consistent with the Freundlich adsorption model, unlike the other two systems which followed the Langmuir adsorption model. The morphology and composition of corrosion products were characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) methods. The SEM and XPS results demonstrated that the nanoemulsion system did not change the material type of corrosion products, but had a visible influence on their morphology. In addition, the inhibition mechanism was also revealed by theoretical calculations. These findings suggest that nano-emulsification technique has the potential to improve the solubility or dispersibility of oil soluble corrosion inhibitor, thereby expanding its application fields.

Physicians' perspectives on different therapeutic approaches for aluminum phosphide poisoning and their relevant outcomes.

Aluminum phosphide is a highly toxic pesticide that results in high mortality. To date, there is neither a definitive antidote nor a unified protocol for managing acute aluminum phosphide poisoning. This cross-sectional questionnaire-based study aims to explore different management approaches and rely on the expertise of Egyptian medical professionals to enhance the prognosis for acute aluminum phosphide poisoning. A self-administered questionnaire was formulated and electronically distributed according to published literature and experience of senior physicians. Responses were received from 151 physicians from 10 governorates. Management modalities were variable among respondents. Noradrenaline was used by 90.7% of respondents with no fixed-dose regimen. In all, 84.1% of participants utilized oil in gastrointestinal decontamination; paraffin oil was the most used solution. Overall, 92.1, 61.6, 46.4, and 34.4% of participants used sodium bicarbonate, proton pump inhibitors, IV magnesium sulfate, and antioxidants, respectively. Regarding the frequency of acute aluminum phosphide poisoning, 47% of participants managed these cases daily or a few times a week. Participants' responses denoted a poor prognosis of acute aluminum phosphide poisoning, and high percentages attributed the prognosis to exposure factors rather than treatment modalities. Statistical analysis revealed that using oil in gastrointestinal decontamination improved the outcome by 4.62-fold. Clinical toxicologists were more likely to rescue≥30% of the cases about 3-fold (2.97) than other specialties. Clinical toxicologists used oil in gastrointestinal decontamination, magnesium sulfate, and antioxidant therapy and calculated base deficit before administration of sodium bicarbonate by 7.70-, 5.30-, 3.26-, and 2.08-fold than other specialties.