Paperboard Samples Research Articles

Functional description of fiber orientation in paperboard based on orientation tensors resulting from μ-CT scans

Modern μ\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\upmu$$\\end{document}-CT scans offer non-destructive three-dimensional microstructure analysis of various materials. Despite small density contrasts, this technology also accurately captures the complex network structure of paper and paperboard. It provides detailed insight into the fiber orientation distribution in paper, which was previously unattainable with existing measurement methods. The image analysis results are applicable for numerical fiber network models, and simulations based on these models can significantly improve our understanding of the microstructural influence on macrostructural paper properties, such as strength, stiffness, and curl tendency. This work presents a new method for investigating the microstructural fiber orientation in paperboard. Orientation tensors obtained from μ\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\\upmu$$\\end{document}-CT scan image processing are extracted and evaluated. Based on the direction of the orientation tensor’s first eigenvector, the fiber orientation distribution is determined and then approximated by periodic and non-periodic probability density functions (PDFs). In this study, 40 commercial paperboard samples, each consisting of three plies, were analyzed. From a given set of commonly used PDFs, the best fitting ones have been identified based on their original location in the paper roll and on their ply. It was found that the von Mises PDF provided the most accurate representation of fiber orientation distribution in the middle ply, while the Elliptical PDF was the most suitable for the outer plies. Moreover, a more pronounced fiber orientation anisotropy was observed at the edges of the paper roll than in its center. The best PDFs and their function parameters are provided to allow for direct usage in numerical microstructure models of paperboard, thus enhancing their representativeness.

Chemical and toxicological characterization of food contact recycled paperboard extracts

Food contact paperboard poses a potential risk of food contamination due to the possible release of chemicals (intentionally added or not), particularly in recycled paperboard. Water extractions were performed, according to wet food procedures, of paperboard samples collected from a manufacturer at the beginning and the end of a recycling production chain. Chemical analysis and hormonal activities in vitro of water extracts were studied. ICP–MS analysis confirmed the presence of 15 trace elements with lower concentrations after the recycling process, with the exception of chlorine. The chromatographic analyses demonstrated that the identified substances in the starting paperboard, before the recycling process, were approximately twice as high as in the end paperboard, after the recycling process. These substances included also natural wood products, chemical additives, and undesirable substances such as phthalates. Two major products (3,5-di-tert-butylphenol and methyl-2-pyrrolidone) were found in the starting and the end paperboard extracts, respectively. Two common substances were identified in both extracts: 2,4-di-tert-buthylphenol and dehydroabietic acid. Evaluation of potential endocrine disruption showed that the starting paperboard extract exhibited oestrogenic and antiandrogenic effects, while these effects nearly disappeared in the end paperboard extract. These results confirmed that the recycling process was effective in removing most of the contaminant substances.

Dynamic out-of-plane compression of paperboard — Influence of impact velocity on the surface

Processes that convert paperboard into finished products include, for example, printing, where the paperboard is subjected to rapid Z-directional (ZD) compression in the print nip. However, measuring and evaluating the relevant properties in the thickness direction of paperboard are not necessarily straightforward or easy. Measuring at relevant, millisecond deformation rates further complicates the problem. The aim of the present work is to elucidate some of the influences on the compressive stiffness. Both the initial material response and the overall compressibility of the paperboard is studied. In this project, the effect on the material response from the surface structure and the millisecond timescale recovery is explored.The method utilized is a machine called the Rapid ZD-tester. The device drops a probe in freefall on the substrate and records the probe position, thus acquiring the deformation of the substrate. The probe is also allowed to bounce several times on the surface for consecutive impacts before being lifted for the next drop. To investigate the time dependent stiffness behavior, the probe is dropped several times at the same XY position on the paperboard from different heights, thus achieving different impact velocities. The material response from drops and bounces combined allows study of the short-term recovery of the material. The material in the study is commercial paperboard. The paperboard samples are compared to material where the surface has been smoothed by grinding it. Our study shows that there is a non-permanent reduction in thickness and a stiffening per bounce of the probe, indicating a compaction that has not recovered in the millisecond timescale. Additionally, a higher impact velocity has an initial stiffening effect on the paperboard, and this is reduced by smoothing the surface.

Analysis of volatile organic compounds and potential odour compounds in food contact paperboard using headspace two-dimensional GC-QTOF-MS

The objective was to establish a robust and reliable approach for the characterisation of volatile organic compounds (VOCs) present in food contact paperboard. This was achieved through the utilisation of headspace solid-phase microextraction in tandem with comprehensive two-dimensional (2D) gas chromatography (GC) and quadrupole time-of-flight mass spectrometry (HS-SPME-GC × GC-QTOF-MS). The experimental parameters were optimised, involving the use of a DVB/C-WR/PDMS fibre at a temperature of 80 °C for a duration of 30 min. A total of 344 VOCs comprising aldehydes, ketones, alcohols, ethers, esters, alkanes and aromatic compounds, were tentatively identified in the samples. Twelve compounds believed to be from biogenic sources had a high odour impact making them major contributors to potential taint from the paperboard samples. Significant attention should be devoted to five compounds namely, 2-methylnaphthalene, 2-pentyl-furan, furfural, 1-octen-3-one and 1-octen-3-ol due to their potential adverse impact on the organoleptic qualities of packaged food items and their potential toxicity. Abbreviations: C-WR: carbon wide range; DVB: divinylbenzene; GC-MS: gas chromatography - mass spectrometry; GCxGC-QTOF-MS: comprehensive two-dimensional gas chromatography coupled to quadrupole-time-of-flight - mass spectrometry; HS-SPME: headspace - solid phase microextraction; LOD: limit of detection; LOQ: limit of quantification; OAV: odor activity values; PDMS: polydimethylsiloxane; RI: retention index; TTC: threshold of toxicological concern; VOC: volatile organic compound

Alternative Fiber-Based Paperboard Adhesion Evaluation with T- and Y-Peel Testing

Due to increased pressure on the availability of wood biomass in the EU and the regulatory attempts to lower CO2 values, where wood-based biomass plays a crucial role in carbon sequestration, the use of cellulose derived from alternative sources is gaining increased interest in the pulp and paper industry as well as in other industries. The processing properties of alternative fiber-based packaging need to be checked in current processing operations with other types of materials and recycling workflows. For example, in the production of folding boxes, after printing other converting properties such as glueability are also of great importance. The adhesive absorption and bonding strength of materials are important as adhesive joints of packaging can interfere with the protective function. In the presented research, three different paperboards produced on a pilot scale from alternative raw material sources were tested. Two paperboards were produced from the alien invasive plants Japanese knotweed and black locust, and one from residual sawdust. The basic paperboard properties were tested regarding paperboard porosity, roughness, z-directional tensile strength, and dynamical behavior regarding liquid interaction (contact angle and liquid penetration dynamic), as water-based adhesives were used in the research. For adhesive joint strength testing, Y- and T-peel adhesion testing was performed on the joint paperboard samples, as still there is no fully standardized method for the evaluation of such fiber-based material properties. The results indicate differences in the penetration dynamics of liquids. This parameter had the highest influence on the peel adhesion strength, while porosity, roughness, and dynamic contact angle were not so significant. Regarding the two adhesive joint tests, the differences in separate materials regarding peel adhesion curves show similar results. However, the Y-peel maximum force values are higher due to the testing setup (in comparison to the T-peel test). The paperboards made from invasive plants showed adhesive joint failures which are more suitable for tamper-proof packaging due to their low surface strength and crack propagation into the fiber structure.

Assessment of paperboard large deformation at fold using digital image correlation technique

Abstract For coated paperboard with large deformations, there is limited knowledge on the mechanisms that lead to coating damage and on the key properties that affect damage. Large deformations produce complex non-linear mechanical responses which often result in significant internal damage. The objective of this work was to establish methods to directly measure local deformation at a fold using a stereo digital image correlation (DIC) technique and a folding device designed in-house. This allowed monitoring of deformation from both cross-section and surface views, from which curvature and strain could be analyzed. This approach allowed observation and quantification of the initiation and propagation of damage. Testing showed that elastic estimation of deformation is valid only at very small curvatures but is still qualitatively useful. It was found that CD fold line shows a lower strain than MD fold line at a given curvature, but it ultimately reaches a higher level of surface strain. Additionally, localized maximum surface strain was shown to correlate better with surface damage at fold than the average surface strain. Furthermore, the introduced discontinuity index can provide a useful tool to compare surface damage at fold even for paperboard samples with different thicknesses.

Development of a reliable extraction method for the identification and quantification of 7 plasticizers in recycled paperboard materials intended for food contact applications

Increasingly, more studies are re-examining widely used chemicals, previously regarded as safe, concerning their potential effect on human health. One such chemical group is plasticizers, commonly known as “everywhere chemicals”. Plasticizers today, like other industrial innovations of the past, are associated with various health concerns. Therefore, guidelines are enforced worldwide through national and international restrictions to limit their use. The purpose of this work is to endorse the use of recycled materials in food packaging, albeit without compromising the safety of the content. To this end, this study attempts to develop a fast, simple, and reliable extraction method for the identification and quantification of low concentrations of these types of chemicals in recycled paperboard materials intended for food contact applications. Three extraction methods were studied and put under evaluation regarding their effectiveness and accuracy in isolating a mixture of 7 plasticizers in samples of recycled paperboard: the Soxtec Extraction (SE), the Ultrasound-Assisted Extraction (UAE), and the Head Space Solid Phase Micro Extraction (HS-SPME). A Gas Chromatography-Mass Spectrometry (GC/MS) analysis was conducted following the extractions to determine the contaminants. The paperboard samples were additionally spiked with the said mixture and subjected to migration experiments using Tenax (dry-food simulant). According to the results, HS-SMPE displayed excellent quantification performance since all 7 compounds were determined with the highest accuracy. Furthermore, both the relative standard deviation (RSD) and the Horwitz ratio (HorRat) values attested that HS-SPME is the best method for extracting the plasticizers out of the three tested.

Mechanical and physical properties of boards made from recycled paper

Due to the increasing accumulation of wastes around the world, the demand for sustainable products is increasing. Paper is a commonly disposed of material that can pose problems even when it is recycled. The concept of using cardboard (CB) as a material for furniture production has been around for many years, but CB furniture does not last long. This study examined the feasibility of using post-consumer recycled paper to produce paper-based boards for furniture design. Cardboard (CB) and office paper (OP) were the main post-consumer materials that were used. The CB and OP were mixed with polylactic acid (PLA) and limestone. The boards were made at a temperature of 200 °C and pressed at a pressure of 3.5 N/mm2 using a single opening hydraulic press. The physical and mechanical properties were tested according to the European standards for wood-based panels. Tests that are critical for furniture parts, such as the modulus of rupture (MOR), the modulus of elasticity (MOE), the internal bond, the screw withdrawal resistance, the thickness swelling, and the water absorption were examined. The paperboard samples exceeded some of the requirements for the general use of boards for interior fitments (including furniture) for use in dry conditions (Type P2) and for non-load bearing boards for use in humid conditions (Type P3).

Assessment of estrogenic compounds in paperboard for dry food packaging with the ERE-CALUX bioassay

Paperboard used as packaging, a non-inert material, can transfer chemicals into food. Over the years, endocrine disrupting compounds (EDCs), such as NonylPhenols (NPs), BisPhenol A (BPA) and phthalates have been shown to migrate from packaging materials into food. Due to chronic exposure and mixture effects of these EDCs, they could cause health effects even at very low doses. Many EDCs are still unknown and many more are still unregulated. The ERE-CALUX bioassay was used as a bioanalytical tool to investigate estrogenic activities of paperboard food packaging and its characteristics, including recycling rate and printing ink. A “worst case” scenario with full extraction is compared to a dry food migration experiment. By measuring an overall estrogenic activity, known and unknown estrogenic chemicals and mixture effects are taken into account and the data are compared to molecule specific analysis. Estrogenic activities ranged from 682 ± 66 pg E2 eq./dm2 to 3250 ± 400 pg E2 eq./dm2 for “worst case” extraction and from 347 ± 30 pg E2 eq./dm2 to 1350 ± 70 pg E2 eq./dm2 for migration experiments. A two-factor ANOVA revealed a relationship between estrogenic activity and the recycling rate of the paperboard, but no significant difference with printing ink was observed for these paperboard samples. Bis(2-ethylhexyl)phthalate (DEHP), dibutyl phthalate (DBP), butyl benzyl phthalate (BBP) and 1,2-cyclohexane dicarboxylic acid diisononyl ester (DINCH) were determined in all extraction and migrations experiment samples. A Spearman rank correlation analysis showed a relationship between the estrogenic activity and the total phthalates as well as with each compound individually.

Toxic Metals in Paper and Paperboard Food Packagings

This study characterized the structure of food packages, determined the amount of toxic metals that pass through the package (due to the package’s condition and contact with food), and examined the appropriateness of current food legislation. The food packages were examined for weight, ash content, and optical properties under two different light sources. The toxic metal quantities of the packages were analyzed with the use of an inductively coupled plasma optical emission spectrometry (ICP-OES ). In all packages, Pb migrated into food and was found at levels that exceeded limit values. Although the amounts of Hg within the material structure were above limits in most packages, it did not migrate from the packages. Although the amount of Cd in structural packaging did not exceed the limit values, most of the migration-related values were high. The Zn concentration in packaging was substantially higher than the amount due to migration. Structural Cu values were mostly below the limit values, except in corrugated boards. Cr amounts in both packaging structure and migration were below the limit values. In all packaging, there were minimum amounts of Ni among paperboard samples and maximum amounts among corrugated boards. Al values were high among structural paper packages, as well as in migration values in paperboard packaging.

Experimental investigation on bending fatigue failure of corrugated paperboard

A series of 3-point bending fatigue tests were conducted to investigate the bending fatigue behaviour of flute type B and C corrugated paperboard samples under cyclic loading. The S-N curve was obtained. The fatigue failure of corrugated paperboard may be described by both Basquin-type and exponential-type S-N curves; however, the exponential-type S-N curve is more appropriate. The stiffness is gradually degraded with almost same energy dissipation in most stress cycles, but it decreases abruptly with the enlarged energy dissipation when the testing cycle is very close to the ultimate cycles of fatigue failure. The corrugated board deforms constantly under the action of cyclic loading, and no visible crack appears. The fatigue failure modes and mechanisms are same for the corrugated boards with B-flute and C-flute; however, the S-N curve of corrugated board is closely related to the flute structure. The results obtained in this paper may be applied to the dynamic design and accelerated vibration test of stacked corrugated boxes.

Genotoxic effects of food contact recycled paperboard extracts on two human hepatic cell lines

ABSTRACTFood contact paperboards may be a potential source of food contamination as they can release chemicals (intentionally added or not), especially recycled paperboards. This study assessed the in vitro genotoxicity of food contact paperboard samples from a manufacturer, collected at the beginning and at the end of a recycling production chain. Samples were extracted in water to mimic a wet food contact. Different genotoxic endpoints were evaluated in two human hepatic cell lines (HepG2 and HepaRG) using bioassays: γH2AX and p53 activation, primary DNA damage with the comet assay and micronucleus formation. It was found that the samples from the beginning and the end of the production chain induced, with the same potency, γH2AX and p53-ser15 activation and DNA damage with the comet assay. The micronucleus assay was negative with the paperboard extract from the beginning of the chain, whereas positive data were observed for the end paperboard extract. These results indicate that samples from recycled food contact paperboard can induce in vitro genotoxic effects in this study’s experimental conditions.

Fluorinated Compounds in U.S. Fast Food Packaging.

Per- and polyfluoroalkyl substances (PFASs) are highly persistent synthetic chemicals, some of which have been associated with cancer, developmental toxicity, immunotoxicity, and other health effects. PFASs in grease-resistant food packaging can leach into food and increase dietary exposure. We collected ~400 samples of food contact papers, paperboard containers, and beverage containers from fast food restaurants throughout the United States and measured total fluorine using particle-induced γ-ray emission (PIGE) spectroscopy. PIGE can rapidly and inexpensively measure total fluorine in solid-phase samples. We found that 46% of food contact papers and 20% of paperboard samples contained detectable fluorine (>16 nmol/cm2). Liquid chromatography/high-resolution mass spectrometry analysis of a subset of 20 samples found perfluorocarboxylates, perfluorosulfonates, and other known PFASs and/or unidentified polyfluorinated compounds (based on nontargeted analysis). The total peak area for PFASs was higher in 70% of samples (10 of 14) with a total fluorine level of >200 nmol/cm2 compared to six samples with a total fluorine level of <16 nmol/cm2. Samples with high total fluorine levels but low levels of measured PFASs may contain volatile PFASs, PFAS polymers, newer replacement PFASs, or other fluorinated compounds. The prevalence of fluorinated chemicals in fast food packaging demonstrates their potentially significant contribution to dietary PFAS exposure and environmental contamination during production and disposal.

Monitoring of contaminants in recycled paperboard for food contact applications.

The lack of harmonized European legislation on food packaging led the Confederation of European Paper Industries to the proposal of a voluntary Industry Guideline for the compliance of paper and board materials for food contact applications. In the present work, a previously established method for the simultaneous determination of contaminants commonly found in recycled paperboard was improved and its applicability as a quality control tool in the paper industry was also assessed. The method involves a sample pre-treatment followed by gas chromatography/mass spectrometry (GC/MS) analysis. For analysis, paperboard samples were collected both from three sections of the same reel and from different reels belonging to the same production run. Results highlighted no significant differences in terms of contaminant distribution among samples, which ensured good sampling representativeness. The performance of the method was considerably improved in terms of linearity range, limits of detection and quantification (5- to 2-fold lower) by using a quadrupole GC/MS system instead of an ion trap GC/MS system. The proposed method could offer a key strategy for analysis of benzophenone derivatives, diisopropyl naphthalene and phthalates in recycled paperboard in order to assess compliance of food packaging with the voluntary limits recommended by the Industry Guideline. © 2016 Society of Chemical Industry.

Flexographic ink-coating interactions: effects of latex variations in coating layers

The effect of coating structure variations on flexographic print quality was studied using pilot-coated paperboard samples with different latex content and latex particle sizes. Two latexes, with particle sizes of 120 nm and 160 nm, were added at either 12 parts per hundred (pph) or 18 pph to the coating formulation. The samples were printed with full tone areas at print forces of 25 N and 50 N in a laboratory flexographic printing press using a waterbased ink. A high ratio of uncovered areas (UCAs) could be detected for the samples that contained 18 pph latex printed at a print force of 25 N. UCAs decreased with increased print force and with decreased amounts of latex in the coating formulation. The fraction of latex covered area on the coating surface was estimated to be 0.35–0.40 for the 12 pph, and 0.70–0.75 for the 18 pph samples. The ink penetration depth into the coating layer could be linked to the fraction of latex-free areas on the coating surface. Optical cross section microscopy indicated that a higher printing force did not increase the depth of penetrated ink to any greater extent. Higher printing force did increase contact between plate and substrate, leading to an improved distribution of the ink. This, in turn, increased print density and decreased UCAs. On closer inspection, the UCAs could be categorized as being induced by steep topographic changes. When appearing at other locations, they were more likely to be caused by poor wetting of the surface. To understand the wetting behavior of the coating surface, observed contact angles were compared with calculated contact angles on surfaces of mixed composition.

Monitoring the Condition of Non-linear Packaging Materials Subject to Varying Excitation Levels Using a Reverse Multiple Input/Single Output Based Approach

During transportation, protective packaging is subjected to random dynamic compressive loads that arise from random vibrations generated by the vehicle. The ability of the protective packaging to withstand these dynamic compressive loads depends on the environmental vibration levels, the nominal stresses and the material's characteristics. Previous research has shown that cumulative damage, in the packaging system under random dynamic compression, will result in a change in the overall stiffness of the system. This change is manifested as a shift in the system's fundamental resonant frequency. Natural frequency estimates are often extracted using a least squares regression curve fit applied to an estimate of the system's frequency response function. Frequency response function estimates are generally obtained using the Fourier transform with a single input/single output (SISO). This approach is suitable for many applications; however, it is not well suited to non-linear systems subjected to non-stationary excitation where the vibration level (overall root-mean-square value) can vary. This paper investigates the use of an optimised reverse multiple input/single output algorithm for reliably tracking variations in the condition of packaging elements subjected to excitation with varying magnitude (root-mean-square). Results are presented from the analysis of physical experiments performed on expanded polystyrene cushions as well as empty corrugated paperboard containers. The experiments performed using the polystyrene samples were designed to limit natural variation in the system's natural frequency; whereas the paperboard samples were allowed to naturally damage under dynamic loading. Copyright © 2015 John Wiley & Sons, Ltd.

Determination of the recovered-fiber content in paperboard samples by applying mid-infrared spectroscopy.

Paperboard is widely used in different applications, such as packaging and graphic printing, among others. Consumption of recycled paper is growing, which has led the paper-mill packaging industry to apply strict quality controls. This means that it is very important to develop methods to test the quality of recycled products. In this article, we focus on determining the recovered-fiber content of paperboard samples by applying Fourier transform mid-infrared (FT-MIR) spectroscopy in combination with multivariate statistical methods. To this end, two very fast, nondestructive approaches were applied: classification and quantification. The first approach is based on classifying unknown paperboard samples into two groups: high and low recovered-fiber content. Conversely, under the quantification approach, the content of recovered fiber in the incoming paperboard samples is determined. The experimental results presented in this article show that the classification approach, which classifies unknown incoming paperboard samples, is highly accurate and that the quantification approach has a root mean square error of prediction of about 4.1.

Antibacterial paperboard packaging using microfibrillated cellulose.

The industry and consumers are focusing more and more on the development of biodegradable and lightweight food-packaging materials, which could better preserve the quality of the food and improve its shelf-life. In an attempt to meet these requirements, this study presents a novel bio-substrate able to contain active bio-molecules for future food-packaging applications. Based on a paperboard substrate, the development of an antibacterial bio-packaging material is, therein, achieved using a chlorhexidine digluconate (CHX) solution as a model of an antibacterial molecule, mixed with microfibrillated cellulose (MFC) and used as coating onto paperboard samples. AFM and FE-SEM analyses were performed to underline the nanoporous MFC network able to trap and to progressively release the CHX molecules. The release study of CHX was conducted in an aqueous medium and showed a lower proportion (20%) of CHX released when using MFC. This led to the constant release of low amounts of CHX over 40h. Antibacterial tests were carried out to assess the preservation of the antibacterial activity of the samples after the release studies. Samples remained active against Bacillus subtilis, with better results being obtained when MFC was used. The preservation of the quality of a model food was finally evaluated paving the way for future promising applications in the food packaging industry.

Silica-Based Nanocoating Doped by Layered Double Hydroxides to Enhance the Paperboard Barrier Properties

Paperboard is an environment-friendly multi-layer material widely used for packaging applications. However, for food packaging paperboard lacks essential barrier properties towards oxygen and water vapor. Conventional solutions to enhance these barrier properties (e.g. paperboard film coating with synthetic polymers) require special manufacturing facilities and difficult the end-of-life disposal and recycling of the paperboard. Paperboard coating with silica-based formulations is an eco-friendly alternative hereby disclosed. Silica-nanocoatings were prepared by sol-gel synthesis, with or without the addition of Zn(2)-Al-NO3 layered double hydroxides (LDHs), and applied on the surface (ca 2 g/m2) of industrial paperboard samples by a roll-to-roll technique. The physicochemical features of silica-nanocoatings were studied by FTIR-ATR, SEM/EDS, XRD analysis and surface energy measurements. The barrier properties of uncoated and silica-coated paperboard were accessed by water vapor transmission rate (WVTR) and oxygen permeability (Jo2) measurements. The best barrier results were obtained for paperboard coated with a mixture of tetraethoxysilane (TEOS) and 3-aminopropyltriethoxysilane (APTES), with and without the incorporation of LDHs.

Investigation on the directional dark-field signals from paperboards using a grating interferometer

Recent advancements in the grating interferometer based Phase Contrast X-ray Imaging (PCXI) technique enables high quality dark-field images to be obtained using conventional X-ray tubes. The dark-field images map the scattering inhomogeneities inside objects. Since, the dark-field image is constructed by considering only those photons which are scattered while passing through the objects, it can reveal useful information about the object inner structures, such as, the fibre structures inside paperboards.The end-use performance of paperboards, such as the printing quality and the stiffness depends on the uniformity in the thickness and the structures of the coating layer of the paperboards. The uniformity in the coating layer is determined by the coating techniques, the coating materials and the topography of the base sheet. In this article, the dark-field signals from four paperboard samples with different quality indices are analysed. The isotropic and the anisotropic scattering coefficients for all of the samples have been calculated. Based on the correlation between the isotropic coefficients and the quality indices of the paperboards, a new method for paperboard quality measurement has been suggested.