Orthogonal Frequency Division Multiplexing Signal Research Articles

Radio-over-fiber systems with delta-sigma-modulation for MMW-based indoor communication

In this paper, we propose and demonstrate a delta-sigma modulator (DSM) based radio-over-fiber (RoF) system for MMW indoor communication. In the experiment, 2-bit DSMs are used to quantize the high-order QAM orthogonal frequency division multiplexing (OFDM) signal into the 16QAM signal. At the receiver, the original high-order signal can be recovered by the low pass filter (LPF) and down-sampling operation. Based on the experimental results, up to 16,384 QAM signals can be transmitted over the DSM-based RoF system without noticeable performance degradation. When the received optical power is high enough, the corresponding error vector magnitude (EVM) and bit error rate (BER) are 0.53% and 7 × 10−3, respectively.

High Spectral Efficiency Photonics-Based Polarization Multiplexing OFDM Signal Delivery at W-Band

We have implemented a large-capacity, long-haul, and high spectral efficiency photonics-based polarization multiplexing communication system at W-band. The signal delivery up to 119.1 Gb/s with spectral efficiency of 9.9 bit/s/Hz is achieved over a 10 km optic-fiber link and 4600 m wireless link. In our study, we utilize an orthogonal frequency division multiplexing (OFDM) scheme to compensate for the signal impairments caused by the dispersion effect and the wireless multipath effect. Based on a pair of antennas, the antenna polarization multiplexing technique is used to realize the polarization-multiplexed mm-wave signal delivery. Also, only one communication link is required, instead of the complex 2×2 line-of-sight multiple-input multiple-output (MIMO) link. Instead of Cassegrain antennas, the combination of plano-convex lens and horn antenna greatly extends the wireless distance. For increasing the spectral efficiency and throughput of the communication system, we employ higher-order modulation formats, probabilistic shaping (PS) techniques, and a series of equalization algorithms. Based on photonics technology, we have created a record-setting distance-rate product of 547.9 Gb/s•km (119.1 Gb/s × 4.6 km) for an independent channel at W-band.

SOA-MZI Differential Transformation Approach Applied on Simultaneous Electro-Optical Mixing

We experimentally incubate a ground-breaking design, for the first time, of concurrent electro-optical semiconductor optical amplifier Mach–Zehnder interferometer mixing (SOA-MZI) based on a differential transformation methodology. Projecting the simultaneous electro-optical mixing system and improving its efficiency and quality achievement in optical and electrical features is a crucial task due to the characteristics of an optical pulse source (OPS) operating with a repetition rate of f= 58.5 GHz and a pulse width duration of 1 picosecond (ps). The resultant of the contemporaneous electro-optical mixing exhibits exceptional passive power stability, reaching 0.8% RMS over a two-hour period. Furthermore, when the optical bandpass filter is controlled at the data wavelength of 1540 nm, we achieve up to 30 dBm of the overall mean output power with an optical conversion gain of 46 dB and an exceptionally high optical signal-to-noise ratio reaching 80 dB. Using orthogonal frequency division multiplexing (OFDM) signals, each data subcarrier is modulated using 128 quadratic amplitude modulation (128-QAM) at carrier frequencies fk and simultaneously up-mixed to high aim frequencies nf±fk at the SOA-MZI output. Additionally, the resulting OFDM_128-QAM up-mixed signal is examined using the specifications for the error vector magnitudes (EVMs) and the electrical conversion gains (ECGs). The SOA-MZI mixing experiment can handle high frequencies up to 120 GHz. Positive ECGs are followed by a sharp reduction over the entire band of the aim frequencies. The highest frequency range achieved during the realistic investigation is shown at 2f+f4= 120 GHz, where the EVM reaches 8% with a symbol rate of 15 GSymb/s. Furthermore, the concurrent OFDM_128-QAM up-mixed signal achieves an absolute maximum bit rate of 80.4 Gbit/s. The investigation into the simultaneous electro-optical mixing regime is finally supported by unmatched characterization improvements.

Support 16384QAM mobile fronthaul based on 3 amplitude quantization Delta-Sigma Modulation

We experimentally demonstrated 16384-ary quadrature amplitude modulation (16384QAM) mobile fronthaul based on 3-amplitude quantization high-pass Delta-sigma Modulation (DSM) in the O band intensity-modulated direct detection (IM/DD) system. By using 3-amplitude quantized high-pass DSM, we successfully quantize the analog waveform of intermediate frequency (IF) Orthogonal Frequency Division Multiplexing (OFDM) signal into 3-Level Pulse Amplitude Modulation (PAM3) signal, and 1 GHz bandwidth 16384-QAM and 1024QAM are successful transmission in 20Gb/s IM/DD link. 0.63% Error Vector Magnitude (EVM) of 16384QAM and 0.7% EVM of 2048QAM are achieved after 25km SSMF and 50km SSMF transmission, respectively. The signal-to-noise ratio (SNR) of the retrieved OFDM signal is 43 dB, which shows that the proposed scheme can support 16384QAM mobile fronthaul network.

Orthogonal frequency‐division multiplexing‐based signal design for a dual‐function radar‐communications system using circulating code array

AbstractIn this study, a dual‐function radar‐communications (DFRC) system based on the circulating code array is presented to address the contradiction between radar and communications system in beam scanning and beam coverage. Processed orthogonal frequency‐division multiplexing (OFDM) signal is transmitted by the circulating code array as the base signal to improve the data rate. Following the spatial angle of the communication receiver, the communication symbols are modulated to part of OFDM signal subcarriers occupying a specific frequency band. A significant property of the circulating code array, which provides a relationship between the baseband frequency of the base signal and the spatial angles, implements a basis for safe telecommunication transmission towards the cooperative receiver and demodulation. Moreover, the circulating code array transmits the same signal and introduces the same time interval between adjacent array elements. Therefore, the complex problems of multi‐dimensional orthogonal signal design in the traditional multiple‐input‐multiple‐output‐based DFRC system design are transformed into a simple base signal design. Finally, an omnidirectional coverage pattern is obtained. Thus, whether the communication receiver is in the mainlobe or the sidelobe of the radar beam, the communication connection can be established between the designed DFRC system and the communication users. The performance of the described DFRC system is verified through theoretical analysis and simulations.

Cyclic Correlation‐Based Blind SNR Estimation for Cyclic Prefix‐Less OFDM System

AbstractThis paper tackles the problem of the signal‐to‐noise ratio estimation for cyclic prefix (CP)‐Less orthogonal frequency division multiplexing (OFDM) system in the presence of Gaussian noise over multipath fading channels. First, we introduce the cyclic correlation of the CP‐Less OFDM signal with CP, and analyze the cyclic correlations for Gaussian noise and received signal. Second, we isolate the Gaussian noise power from the signal power. Finally, we obtain the close form expression of SNR estimation by using cyclic correlations. Computer simulation results verify the effectiveness of the proposed method.

Coordinated-security based on probabilistic shaping and encryption in MMW-RoF system.

A coordinated-security probabilistic shaping (PS) physical layer encryption scheme is proposed for a W-band millimeter-wave radio-over-fiber (MMW-RoF) system. This scheme mainly includes substituting encryption, coordinated encrypted PS, and unequal length grouping scrambling, which can realize the coordination between PS and chaotic encryption. The key space of the proposed scheme is 10103, which can effectively prevent against brute force cracking and chosen-plaintext attacks. The encrypted orthogonal frequency division multiplexing (OFDM) signal is successfully transmitted over 50-km standard single-mode fiber (SSMF) and a 5-m wireless channel. The results show that the proposed scheme achieves 0.8-dB received optical power gain at a bit error rate (BER) of 10-3 compared with a traditional OFDM signal. The superiority of the proposed scheme in security performance and BER performance has been verified.

Digital self-interference cancellation for full-duplex systems based on deep learning

Full-duplex (FD) systems can double the spectrum efficiency by allowing users to transmit and receive signals at the same time and in the same frequency band. However, in FD systems the receiver suffers severe self-interference (SI) caused by the transmitter and eliminating the SI is challenging. In this paper, we propose a novel digital self-interference cancellation (SIC) scheme based on deep learning, which combines the power of sliding window, gated recurrent unit (GRU) network and attention mechanism (AM). The proposed scheme can accurately reconstruct the SI through two steps. It first processes the sample signals utilizing the sliding window and then extracts the dependence in preprocessed signals by applying the GRU with AM. We adopt the orthogonal frequency division multiplexing (OFDM) signal as the baseband transmitted signal to verify the proposed scheme. Extensive experiments demonstrate that the SIC capability of the developed scheme is at least 14.46 dB higher than the existing polynomial and neural network (NN) schemes. Furtherly, the effectiveness of the scheme is verified in different interference-to-noise ratio (INR), multipath channel, training sample and OFDM symbol situations.

28 GHz over-the-air measurement using an OTFS multi-user distributed MIMO under Doppler effect

AbstractThis paper describes the experimental investigation of orthogonal time-frequency space (OTFS) modulation using a 28 GHz multi-user distributed multiple-input multiple-output (D-MIMO) testbed in over-the-air (OTA) and mobility environments to enhance cell throughput in a millimeter-wave band. We build the D-MIMO testbed having newly developed OTFS modulator and demodulator, and measured OTFS signals and orthogonal frequency-division multiplexing (OFDM) signals with up to four user simultaneous connections on an actual office floor. Additionally, the Doppler effect on OTFS signals is mathematically analyzed and is confirmed in the measurements. OTFS indicates higher robustness in time-variant channels than OFDM. The error vector magnitude (EVM) and system throughput of OTFS are −22 dB and 1.9 Gbps with 100 MHz signal bandwidth, respectively. To our knowledge, this is a first paper describing the OTA measurements of EVM, throughput, and spectral efficiency using OTFS modulation on the 28 GHz coherent beamforming system.

Deep Learning-Assisted OFDM Channel Estimation and Signal Detection Technology

The orthogonal frequency division multiplexing (OFDM) technique has received wide attention because of its high spectrum utilization. However, the drawback of inter-subcarrier interference in OFDM systems makes the channel estimation and signal detection performance of OFDM systems with few pilots and short cyclic prefixes (CP) poor. In this paper, we use deep learning to assist OFDM in recovering nonlinearly distorted transmission data. Specifically, we use a self-normalizing network (SNN) for channel estimation, combined with a convolutional neural network (CNN) and a bidirectional gated recurrent unit (BiGRU) for signal detection, thus proposing a novel SNN-CNN-BiGRU network structure (SCBiGNet). The simulation results show that the SCBiGNet model outperforms the existing techniques for the different numbers of pilots and lengths of CPs. The BER performance is improved by 0.2~9 dB.

Constant envelope OFDM transmission over metro-regional optical links

The transmission of constant envelope orthogonal frequency division multiplexing (CE-OFDM) signals is experimentally demonstrated in this paper to increase the reach of metro-regional optical links. A recirculating fiber loop was implemented for this aim. A reach extension of 100 km of standard single-mode fiber was achieved with the CE-OFDM-based system, considering 16 quadrature amplitude modulation (16-QAM) as subcarrier mapping and links without optical dispersion compensation. Link lengths as long as 700 km, with spectral efficiency of 1.89 b/s/Hz, were accomplished with performances below the forward error correction limit.

Ultrawideband RF-IQ Modulator Using Segmented Nonlinearly Scaled RF-DACs and Nonoverlapping LO Signals

A wideband Cartesian in-phase and quadrature (I/Q) modulator based on dual 10 b RF-digital-to-analog converters (DACs) is presented. Nonoverlapping local oscillator (LO) signals and a segmented nonlinear scaling with scaled unit cells contribute to a high linearity and allow for a low-complexity digital predistortion (DPD). Unit-cell flip-flops (FFs) and a balanced clock distribution enable a high sample rate with little skew. Out-of-band emissions are reduced through drive-slope control of the data-switch inputs. The modulator, implemented in the 22-nm fully-depleted silicon-on-insulator (FDSOI) CMOS, operates between 20 and 26 GHz with a peak sample rate of 11 GS/s. It has been used to demonstrate the transmission of a 64-quadrature amplitude modulation (QAM) single-carrier (SC) signal at 13.2 Gb/s, a 256-QAM SC signal at 7.33 Gb/s, and an orthogonal frequency division multiplexing (OFDM) signal comprising four aggregated 400-MHz 64-QAM channels with an error vector magnitude (EVM) of 6.43%. These results demonstrate the potential of the proposed modulator for the realization of ultrawideband transmitters in high-performance millimeter-wave (mmW) systems.

A Millimeter-Wave Three-Way Doherty Power Amplifier for 5G NR OFDM

This article presents a millimeter-wave (mmWave) three-way Doherty output network and its silicon implementation at 38 GHz for 5G new radio (NR) orthogonal frequency-division multiplexing (OFDM). The proposed network synthesis methodology can realize impedance levels that are close to the ideal three-way Doherty operation, reduce the impedance transformation ratio at back-off, and directly absorb the device’s parasitic capacitance. Its design procedure and tradeoffs are discussed in detail. A 38-GHz power amplifier (PA) prototype is implemented in the GlobalFoundries 45-nm CMOS SOI process, achieving 13.7%/11.0% power-added efficiency (PAE) at the 9.5-/11.5-dB back-off, which is among the highest compared with recently reported silicon PAs operating at 35 GHz and above. Tested under 1-and 2-component carrier (CC) 5G NR FR2 64-QAM OFDM signals in the Band n260, the PA demonstrates state-of-the-art average output power (11.3 dBm) and average efficiency (14.7%) with <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$-$</tex-math> </inline-formula> 25-dB error vector magnitude (EVM). The design robustness and reliability are further demonstrated through the testing of multiple samples and PA lifetime.

Nonlinear polarization crosstalk canceled wavelength conversion for Pol-Mux OFDM signal with polarization-diversity FWM.

We present a model that is capable of describing the polarization crosstalk in terms of nonlinear polarization rotation (NPR) of semiconductor optical amplifier (SOA) in wavelength conversion for polarization multiplexing (Pol-Mux) orthogonal frequency division multiplexing (OFDM) signal. Then a simple nonlinear polarization crosstalk canceled wavelength conversion (NPCC-WC) with polarization-diversity four-wave mixing (FWM) is proposed. The effectiveness is achieved successfully in the proposed wavelength conversion for the Pol-Mux OFDM signal by using simulation. In addition, we studied the influence of several system parameters on the performance, including the power of the signal, SOA's injection current, frequency spacing, polarization angle of signal, laser linewidth, and modulation order. The results show that the proposed scheme has better performance due to crosstalk cancellation than the conventional scheme, such as wider wavelength tunability, lower polarization sensitivity, and wider laser linewidth tolerance.

High security optical OFDM transmission scheme with four-dimensional region joint encryption based on power division multiplexing.

In this paper, a high security chaotic encryption scheme for orthogonal frequency division multiplexing (OFDM) transmission system is proposed by using power division multiplexing (PDM) technology and four-dimensional region joint encryption. The scheme uses PDM to realize simultaneous transmission of multiple user information, which can achieve a good compromise among system capacity, spectral efficiency and user fairness. In addition, bit cycle encryption, constellation rotation disturbance (CRD) and region joint constellation disturbance (RJCD) are used to realize four-dimensional region joint encryption, effectively improving the physical layer security. The masking factor is generated by the mapping of two-level chaotic systems, which can enhance the nonlinear dynamics and improve the sensitivity of encrypted system. A 11.76 Gb/s OFDM signal transmission over 25 km standard single-mode fiber (SSMF) is experimentally demonstrated. At the forward-error correction (FEC) bit error rate (BER) limit -3.8×10-3, the proposed receiver optical power based on quadrature phase shift keying (QPSK) without encryption, QPSK with encryption, variant-8quadrature amplitude modulation (V-8QAM) without encryption and V-8QAM with encryption are about -13.5dBm, -13.6dBm, -12.2dBm, and -12.1dBm. The key space is up to 10128. The results show that this scheme not only improves the security of the system and the ability to resist attackers, but also improves the system capacity and has the potential to serve more users. It has a good application prospect in the future optical network.

Receive-diversity-aided power-fading compensation for C-band IM/DD OFDM systems.

A receive-diversity-aided power-fading compensation (RDA-PFC) scheme is proposed and demonstrated to eliminate the chromatic dispersion (CD)-induced power fading for C-band double-sideband (DSB) intensity modulation and direct detection (IM/DD) orthogonal frequency division multiplexing (OFDM) systems. By combining the responses before and after a dispersive element using a maximal-ratio combining (MRC) algorithm, the CD-induced power fading dips within the signal bandwidth of around 50 GHz can be effectively compensated for, which results in an up to 17.6-dB signal-to-noise ratio (SNR) improvement for the fading subcarriers after transmission over 10 km of standard single-mode fiber (SSMF). Using the 16 quadrature amplitude modulation (QAM) format, a diversity receiver with the proposed RDA-PFC scheme can support 170.6-Gbit/s OFDM signal transmission over a 10-km SSMF and reduces the bit error rate (BER) by more than an order of magnitude compared with a conventional receiver. Moreover, 208.1-Gbit/s adaptive bit and power loading OFDM signal transmission over a 10-km SSMF is realized by the proposed RDA-PFC scheme, which improves the capacity by 15.3% compared with the case without RDA-PFC at a BER of 3.8 × 10-3. The proposed RDA-PFC scheme shows great potential in CD-induced power-fading compensation for high-speed IM/DD OFDM systems.

Demonstration of High Capacity Bidirectional A-RoF System Using Wavelength Reuse and Frequency Multiplexing

We demonstrate a practical wavelength reuse bidirectional analog radio-over-fiber (A-RoF) system served by a single distributed feedback (DFB) laser. Frequency interleaving of downlink and uplink signals is proposed to ameliorate the spectral efficiency and mitigate the interference raised by the bidirectional transmission. Pre-emphasis is exploited to counteract the performance impairment brought about by the interaction between laser chirp and fiber chromatic dispersion. Through employing 64-QAM modulated 16 bands and 16-QAM modulated 12 bands filtered orthogonal frequency division multiplexing (f-OFDM) signals with 200 MHz bandwidth, asymmetric transmission with superior flexibility over 25 km fiber is attained, with an aggregate capacity of 20 Gb/s for downlink and 10 Gb/s for uplink. The mutual interference between the downlink and uplink is explored by overlapping the downlink and uplink signal spectra to varying degrees. Using the optimum frequency configuration, system performance is evaluated in terms of EVM and phase noise. To further investigate the effects caused by the Rayleigh backscattering and the stimulated Brillouin scattering (SBS), simulations are conducted on the proposed architecture, validating the conclusion from the experiment that the bidirectional transmission is primarily limited by the Rayleigh backscattering than the stimulated Brillouin scattering.

Photonics-Assisted Analog Wideband Self-Interference Cancellation for In-Band Full-Duplex MIMO Systems With Adaptive Digital Amplitude and Delay Pre-Matching

A photonics-assisted analog wideband RF self-interference (SI) cancellation and frequency downconversion approach for in-band full-duplex (IBFD) multiple-input multiple-output (MIMO) systems with adaptive digital amplitude and delay pre-matching is proposed based on a dual-parallel Mach–Zehnder modulator (DP-MZM). In each MIMO receiving antenna, the received signal, including different SI signals from different transmitting antennas and the signal of interest, is applied to one arm of the upper dual-drive Mach–Zehnder modulator (DD-MZM) of the DP-MZM, the reference signal is applied to the other arm of the upper DD-MZM, and the local oscillator signal is applied to one arm of the lower DD-MZM. The SI signals are canceled in the optical domain in the upper DD-MZM and the frequency downconversion is achieved after photodetection. To cancel the SI signals, the analog reference signal is constructed in the digital domain, while the amplitude and delay of the constructed reference are adjusted digitally by upsampling with high accuracy. Experiments are performed when two different SI signals are employed. The genetic algorithm or least squares algorithm is combined with segmented search respectively for the SI signal reconstruction and amplitude and delay pre-matching. A cancellation depth of around 20 dB is achieved for the 1-Gbaud 16 quadrature-amplitude modulation orthogonal frequency-division multiplexing signal.

Fiber-terahertz-fiber bridge system in the 355-GHz band using a simple optical frequency comb and a photonics-enabled receiver.

This Letter demonstrates a high-speed fiber-terahertz-fiber system in the 355-GHz band using stable optical frequency comb generation and a photonics-enabled receiver. At the transmitter, a single dual-drive Mach-Zehnder modulator is employed to generate a frequency comb by driving the modulator under an optimal condition. At the antenna site, a photonics-enabled receiver consisting of an optical local oscillator signal generator, a frequency doubler, and an electronic mixer is used to downconvert the terahertz-wave signal to the microwave band. Simple intensity modulation and a direct detection method are used for transmitting the downconverted signal to the receiver over the second fiber link. To demonstrate the proof of concept, we transmitted a 16-quadrature amplitude modulation (QAM) orthogonal frequency-division multiplexing signal over a system consisting of two radio-over-fiber links and a 4 m wireless link in the 355-GHz band and achieved a line rate of 60 Gb/s. We also successfully transmitted a 16-QAM subcarrier multiplexing single-carrier signal over the system and achieved a capacity of 50 Gb/s. The proposed system can facilitate the deployment of ultra-dense small cells in high-frequency bands in beyond-5G networks.

65,536-QAM OFDM signal transmission over a fiber-THz system at 320 GHz with delta-sigma modulation.

The transmission of a 65,536-ary quadrature amplitude modulation (QAM) orthogonal frequency division multiplexing (OFDM) signal supported by a hybrid fiber-terahertz (THz) multiple-input multiple-output (MIMO) system at 320 GHz is experimentally demonstrated in this Letter. We adopt the polarization division multiplexing (PDM) technique to double the spectral efficiency. Based on a 23-GBaud 16-QAM link, 2-bit delta-sigma modulation (DSM) quantization enables 65,536-QAM OFDM signal transmission over a 20-km standard single-mode fiber (SSMF) and a 3-m 2 × 2 MIMO wireless delivery, and satisfies the hard-decision forward error correction (HD-FEC) threshold of 3.8 × 10-3, corresponding to a net rate of 60.5 Gbit/s for THz-over-fiber transport. Meanwhile, below the fronthaul error vector magnitude (EVM) threshold of 0.34%, a maximum signal-to-noise ratio (SNR) of 52.6 dB is achieved. To the best of our knowledge, this is the highest modulation order achievable for DSM applications in THz communication.