Optical Parametric Chirped Pulse Amplification Research Articles

Efficient generation of femtosecond millijoule pulses at 3.1 µm.

3.2-mJ, 92-fs pulses centered at 3.1 µm are generated at a 1-kHz repetition rate through a tabletop optical parametric chirped pulse amplification (OPCPA) system based on ZnGeP2 crystals. Pumped by a 2-µm chirped pulse amplifier with a flat-top beam profile, the amplifier achieves a 16.5% overall efficiency, which, to the best of our knowledge, is the highest efficiency achieved by OPCPA at this wavelength. Harmonics up to the seventh order are observed after focusing the output in the air.

Optical and laser damage properties of 98% deuterium DKDP crystal in different crystal orientations

Served as electro-optic switch, frequency converter and the optical parametric chirped pulse amplifier (OPCPA), highly deuterated DKDP crystals are critical optical elements in high power laser systems. In our work, samples taken in Z direction and Ⅰ-type phase-match direction from an as-grown high deuterium DKDP crystal, which was grown by the rapid growth method with continuous filtration. Thermo-gravimetric apparatus (TGA) measurement was applied to obtain the deuterium content of the DKDP crystal. the results showed the deuterium level of the samples in our experiments exceeded 98%. The ultraviolet–visible–near-infrared transmittance spectrum showed that the transmittance of Z-cut at 532 nm and Ⅰ-type at 1064 nm were 92.99% and 96.07%, respectively. The 0% laser-induced damage threshold of Z-cut in 1064 nm was about 40J/cm2, exceeding much more than the application requirement in certain high power laser systems. The polarization state of laser had little effect on the laser-induced damage characteristics of Ⅰ-type sample. Then the laser-induced damage morphologies of 98% DKDP crystals induced by the 1064 nm and 532 nm lasers were investigated. The results indicated that the "micro-explosion" of different kinds of defects in the bulk led to different damage morphologies, and many cracks in the damage pinpoints presented the regular orientation with better consistency in view of the Ⅰ-type phase-match direction. Our research can provide a reference for the applications of highly deuterated DKDP crystals in high power laser systems.

Demonstration of 85% pump depletion and 10−6 noise content in quasi-parametric chirped-pulse amplification

Full pump depletion corresponds to the upper limit of the generated signal photons relative to the pump pulse; this allows the highest peak power to be produced in a unit area of ultraintense laser amplifiers. In practical systems based on optical parametric chirped-pulse amplification, however, the typical pump depletion is only ~35%. Here, we report quasi-parametric chirped-pulse amplification (QPCPA) with a specially designed 8-cm-thick Sm:YCOB crystal that highly dissipates the idler and hence improves pump depletion. We demonstrate 56% QPCPA energy efficiency for an 810-nm signal converted from a 532-nm pump, or equivalently 85% pump depletion. As another advantage, such a record high depletion greatly suppresses the parametric superfluorescence noise in QPCPA to only ~1.5 × 10−6 relative to the amplified signal energy. These results pave the way to beyond the ten-petawatt peak power of the currently most intense lasers.

All-polarization-maintaining and high-energy fiber optical parametric chirped-pulse amplification system using a solid core photonic hybrid fiber.

We present an all-fiber optical parametric chirped-pulse amplification integrated system delivering a single-mode polarized beam. The system makes use of a specifically designed solid-core photonic hybrid fiber (i.e., combining modified total internal reflection and photonic bandgap mechanisms) that ensures sufficient birefringence to maintain the signal polarization. Moreover, the fiber combines a large mode area to handle energetic pump pulses (without generating damage or unwanted nonlinear effects) and weak dispersion to generate parametric gain bands broad enough to amplify ultrashort pulses. An efficient parametric process allows for obtaining a very high gain (>45 dB) with an output pulse energy reaching µJ range at 1053 nm by using a single 5-m hybrid fiber amplifier.

Laser damage mechanism and threshold improvement of nonlinear optical La3Ga5.5Nb0.5O14 crystal for a mid-infrared high-intensity laser

Laser damage threshold (LDT) is critical for optical devices in high-intensity laser applications. Understanding the influence mechanism of a high-intensity laser on optical materials is principal for improving the materials’ LDTs. Here, the LDT of La3Ga5.5Nb0.5O14 (LGN) crystals, the most promising nonlinear optical material for mid-infrared optical parametric chirped-pulse amplification (OPCPA), were studied, and its laser damage mechanism was elucidated. Oxygen vacancies in different ligands have important and distinct effects on LDTs and introduce defect levels, playing primary roles in the reduction of LDTs by the absorption of electrons in the conduction bands. The formation of F-centers also decreases LDTs via two-photon absorption. In addition, the linear absorption of free electrons in the conduction bands contributes more than the two-photon absorption, induced by the defect level, in the nanosecond laser damage process. By annealing in optimized conditions, the 0% laser damage probability of the LGN crystals was measured up to 13.1 J/cm2, which is a 24% improvement compared with that of the as-grown sample, and the highest of the mid-infrared nonlinear optical crystals. The results can not only lead to further improvements in the laser amplification properties in OPCPA systems but also inspire further studies on the application of optical materials in high-intensity lasers.

Wavelength-Dependent Wavefront Produced and Controlled in Optical Parametric Chirped-Pulse Amplification

Wavelength-Dependent Wavefront Produced and Controlled in Optical Parametric Chirped-Pulse Amplification

Ultra-broadband long-wave-infrared pulse production using a chirped-pulse difference-frequency generation.

We present a broadband light source based on near-infrared chirped-pulse difference-frequency mixing that is suitable for seeding long-wave-infrared (LWIR) optical parametric chirped-pulse amplification (OPCPA). A nitrocellulose pellicle is used in a Ti:sapphire regenerative amplifier to generate dual-frequency output pulses, which are subsequently mixed in a 0.4-mm thick AgGaS2 crystal. LWIR pulses with ∼1 µm full width at half maximum (FWHM) bandwidth centered at 10.5 µm are generated by mixing transform-limited pulses. Assisted by genetic algorithm optimization, the bandwidth is broadened to ∼3 µm FWHM within the 8-12 µm atmospheric transmission window. The seed source paves the path towards tabletop ultrafast terawatt-class passively carrier-envelope-phase stabilized OPCPA in the LWIR region.

Optical modification of nonlinear crystals for quasi-parametric chirped-pulse amplification

Quasi-parametric chirped-pulse amplification (QPCPA), which features a theoretical peak power much higher than those obtained with Ti:sapphire laser or optical parametric chirped-pulse amplification, is promising for future ultra-intense lasers. The doped rare-earth ion used for idler dissipation is critical for effective QPCPA, but is usually not compatible with traditional crystals. Thus far, only one dissipative crystal of Sm3+-doped yttrium calcium oxyborate has been grown and applied. Here we introduce optical means to modify traditional crystals for QPCPA applications. We theoretically demonstrate two dissipation schemes by idler frequency doubling and sum-frequency generation with an additional laser. In contrast to absorption dissipation, the proposed nonlinear dissipations ensure not only high signal efficiency but also high small-signal gain. The demonstrated ability to optically modify crystals will facilitate the wide application of QPCPA.

10-µJ few-cycle 12-µm source based on difference-frequency generation driven by a 1-kHz mid-wave infrared OPCPA.

We report on high-energy, few-cycle pulse generation in the long-wave infrared spectral region via difference-frequency generation (DFG) in GaSe and AgGaSe2 nonlinear crystals. The DFG is driven by the signal at 3.5 µm and idler at 5 µm of a high-power mid-wave infrared optical parametric chirped pulse amplification (OPCPA) system operating at a 1-kHz repetition rate. The DFG pulses contain up to 17 µJ of energy and cover a spectrum from 8.5 µm to 14.5 µm. They are generated with a conversion efficiency of 2.1 %. Compression results in 10.2-μJ pulses with sub-150-fs duration, corresponding to less than four optical cycles.

Versatile few-cycle high-energy MID-IR OPCPA for nonlinear optics, spectroscopy and imaging

High-power, high-energy, ultrashort, mid-infrared (MID-IR) laser systems operating at high repetition rates are of considerable interest for many science applications, such as coherent vibrational spectroscopy, label-free imaging, time-resolved pump-probe and high-harmonic generation studies. We developed an optical parametric chirped-pulse amplifier (OPCPA) system employing a difference-frequency generation in a lithium gallium sulfide nonlinear crystal in the final amplifier stage, which provides in principle the possibility for passive carrier-envelop-phase (CEP) stability. The OPCPA efficiently down-converts a 1 μm 200 μJ Yb-YAG pump pulse into the MID-IR spectral range generating μJ-level pulses at a repetition rate of 200 kHz. Two modes of operations providing complimentary MID-IR pulse properties are presented. Depending on the envisaged application, one can switch between (a) a wavelength-tunable (4.2–11 μm) source and (b) a broadband source centered at ≈8.5 μm by controlling the group-delay dispersion of the signal pulse. The broadband, high-energy MID-IR pulses have a short pulse duration of 74±2 fs, which corresponds to only ≈3 optical cycles at the central wavelength of 8.5 μm.

Impact of the optical parametric amplification phase on laser pulse compression.

Optical parametric chirped-pulse amplification (OPCPA) is an effective way to generate ultrashort pulses that has been used extensively for a variety of applications requiring high peak intensities. Precise control and measurement of a system's spectral and spatial phases are required for Fourier-transform-limited pulse compression and diffraction-limited focusing. Phase accumulated during optical parametric amplification (OPA) can degrade the compressibility and focusability of the pulse, reducing peak intensity. We used analytic and numerical analysis of OPA to study the influence of crystal parameters, the wavefront of the pump and signal, and their relative optical alignment on the accumulated phase. We show that the accumulated signal phase is largely independent of amplifier saturation and, with significant local wavefront gradients in the signal or pump beam, the quality of the compressed pulses can be degraded. We use first-order expressions for the pump- and signal-angle sensitivity to evaluate an OPCPA system consisting of a highly deuterated potassium dihydrogen phosphate amplifier designed to support bandwidth for 15 fs pulses centered at 920 nm.

Effect of the pump beam profile and wavefront on the amplified signal wavefront in optical parametric amplifiers.

We present a theoretical and experimental analysis of the signal phase introduced by the pump-beam wavefront and spatial profile during optical parametric amplification (OPA) process. The theory predicts the appearance of an additional wavefront in the amplified signal beam that is proportional to the spatial derivative of the pump-beam wavefront. The effect of the pump-beam profile on the signal-beam wavefront is also investigated. Our experiments tested these theoretical predictions by comparing the wavefront of the signal beam before and after amplification in a multi-joule broadband OPA. The measured signal wavefront was shown to have the expected dependence on the pump-beam profile and wavefront. These results can be considered when designing petawatt-scale ultrabroadband optical parametric chirped-pulse-amplification systems.

Sub-50 fs pulses at 2050 nm from a picosecond Ho:YLF laser using a two-stage Kagome-fiber-based compressor

The high-energy few-cycle mid-infrared laser pulse beyond 2 μm is of immense importance for attosecond science and strong-field physics. However, the limited gain bandwidth of laser crystals such as Ho:YLF and Ho:YAG allows the generation of picosecond (ps) long pulses and, hence, makes it challenging to generate few-cycle pulse at 2 μm without utilizing an optical parametric chirped-pulse amplifier (OPCPA). Moreover, the exclusive use of the near-infrared wavelength has limited the generation of wavelengths beyond 4 μm (OPCPA). Furthermore, high harmonic generation (HHG) conversion efficiency reduces dramatically when driven by a long-wavelength laser. Novel schemes such as multi-color HHG have been proposed to enhance the harmonic flux. Therefore, it is highly desirable to generate few-cycle to femtosecond pulses from a 2 μm laser for driving these experiments. Here, we utilize two-stage nonlinear spectral broadening and pulse compression based on the Kagome-type hollow-core photonic crystal fiber (HC-PCF) to compress few-ps pulses to sub-50 fs from a Ho:YLF amplifier at 2 μm at 1 kHz repetition rate. We demonstrate both experimentally and numerically the compression of 3.3 ps at 140 μJ pulses to 48 fs at 11 μJ with focal intensity reaching 10 13 W / cm 2 . Thereby, this system can be used for driving HHG in solids at 2 μm. In the first stage, the pulses are spectrally broadened in Kagome fiber and compressed in a silicon-based prism compressor to 285 fs at a pulse energy of 90 μJ. In the second stage, the 285 fs pulse is self-compressed in air-filled HC-PCF. With fine-tuning of the group delay dispersion (GDD) externally in a 3 mm window, a compressed pulse of 48 fs is achieved. This leads to a 70-fold compression of the ps pulses at 2050 nm. We further used the sub-50 fs laser pulses to generate white light by focusing the pulse into a thin medium of YAG.

Recent progress on acentric La3Nb0.5Ga5.5O14 crystals: large-size growth and application to ultrafast mid-infrared laser systems [Invited

Optical parametric chirped-pulse amplification (OPCPA) can be used to generate ultrafast intense mid-IR lasers, however, the lack of suitable nonlinear optical crystals simultaneously having a wide transmission range, high laser damage threshold, and excellent phase-matching property hinders the development of mid-IR OPCPA. Here, we focus on the La3Nb0.5Ga5.5O14 (LGN) crystal and describe its growth, characterization, and application in mid-IR nonlinear frequency converters. We discuss the optimization of the starting polycrystalline component and temperature field aimed for the growth of large-size LGN crystals with a 60 mm diameter. We then present a detailed characterization of their optical properties, including transmission spectrum, refractive indices, and nonlinear coefficient. Our findings suggest the promising potential of LGN in generating both few-cycle pulses across 3 to 6 µm and terawatt-class OPCPA systems around 5 µm.

Cr:ZnS-based soliton self-frequency shifted signal generation for a tunable sub-100 fs MWIR OPCPA.

We present a tunable, high-energy optical parametric chirped pulse amplification system with a front-end based on a femtosecond Cr:ZnS laser. By taking advantage of the broad emission spectrum of the femtosecond Cr:ZnS master oscillator, we are able to directly seed the holmium-based pump around 2 µm. At the same time, the signal pulses for the parametric process are generated via Raman self-frequency shifting of the red end of the spectrum centered at 2.4 µm. The solitons, generated in a fluoride fiber, are tunable over the wavelength range between 2.8 and 3.2 µm. The optical parametric amplifier operates at a 1 kHz repetition rate, and consists of two stages equipped with ZGP as nonlinear crystal. The generated idler pulses are tunable between 5.4 and 6.8 µm with a pulse energy of up to 400 µJ. Dispersion management using bulk material stretching and compression in combination with precise phase shaping prior to amplification enables idler pulses of a sub-100 fs duration, translating into a peak power as high as 4 GW.

Utilizing the temporal superresolution approach in an optical parametric synthesizer to generate multi-TW sub-4-fs light pulses.

The Fourier-transform limit achieved by a linear spectral phase is the typical optimum by the generation of ultrashort light pulses. It provides the highest possible intensity, however, not the shortest full width at half maximum of the pulse duration, which is relevant for many experiments. The approach for achieving shorter pulses than the original Fourier limit is termed temporal superresolution. We demonstrate this approach by shaping the spectral phase of light from an optical parametric chirped pulse amplifier and generate sub-Fourier limited pulses. We also realize it in a simpler way by controlling only the amplitude of the spectrum, producing a shorter Fourier-limited duration. Furthermore, we apply this technique to an optical parametric synthesizer and generate multi-TW sub-4-fs light pulses. This light source is a promising tool for generating intense and isolated attosecond light and electron pulses.

Femtosecond optical parametric chirped-pulse amplification in birefringent step-index fiber.

We demonstrate an optical parametric chirped-pulse amplifier (OPCPA) that uses birefringence phase matching in a step-index single-mode optical fiber. The OPCPA is pumped with chirped pulses that can be compressed to sub-30-fs duration. The signal (idler) pulses are generated at 905 nm (1270 nm), have 26 nJ (20 nJ) pulse energy, and are compressible to 70 fs duration. The short compressed signal and idler pulse durations are enabled by the broad bandwidth of the pump pulses. Numerical simulations guiding the design are consistent with the experimental results and predict that scaling to higher pulse energies will be possible. Forgoing a photonic crystal fiber for phase-matching offers practical advantages, including allowing energy scaling with mode area.

Spatio-spectral couplings in saturated collinear OPCPA.

Ultrafast laser pulses featuring both high spatio-temporal beam quality and excellent energy stability are crucial for many applications. Here, we present a seed laser with high beam quality and energy stability, based on a collinear optical parametric chirped pulse amplification (OPCPA) stage, delivering 46 µJ pulses with a 25 fs Fourier limit at 1 kHz repetition rate. While saturation of the OPCPA stage is necessary for achieving the highest possible energy stability, it also leads to a degradation of the beam quality. Using simulations, we show that spectrally dependent, rotationally symmetric aberrations dominate the collinear OPCPA in saturation. We experimentally characterize these aberrations and then remove distinct spatial frequencies to greatly improve the spectral homogeneity of the beam quality, while keeping an excellent energy stability of 0.2 % rms measured over 70 hours.

Numerical Investigation of the Temporal Contrast in ps-OPCPA with Compact Double BBO Arrangement

The picosecond optical parametric chirped pulse amplifier (ps-OPCPA) with double BBO arrangement can support the ultrabroad spectrum even under a relatively long pump pulse duration (∼100 ps). In this work, five-wave-coupled equations taking into consideration different phase matching conditions between the parametric superfluorescence (PSF) and the signal are proposed to investigate the temporal contrast in ps-OPCPA schemes. Both the temporal contrast and the amplified spectrum are numerically analyzed in double BBO arrangements with four phase matching conditions. Numerical results show that the high temporal contrast and ultrabroad spectrum can be simultaneously realized by choosing the proper phase matching geometry in a double BBO arrangement. The numerical investigation here relaxes the requirement of very short pump pulses in ps-OPCPA, which can provide beneficial guidance for the design and construction of ps-OPCPA.

13.4 fs, 0.1 Hz OPCPA Front End for the 100 PW-Class Laser Facility

Here, we report the recent progress on the front end developed for the 100 PW-class laser facility. Using 3 stages of optical parametric chirped-pulse amplification (OPCPA) based on lithium triborate (LBO) crystals, we realized a 5.26 J/0.1 Hz amplified output with a bandwidth over 200 nm near the center wavelength of 925 nm. After the compressor, we obtained a pulse duration of 13.4 fs. As the compression efficiency reached 67%, this OPCPA front end could potentially support a peak power of 263 TW at a repetition rate of 0.1 Hz. To the best of our knowledge, among all the 100 TW-level OPCPA systems, it shows the widest spectral width, the shortest pulse duration, and it is also the first OPCPA system working at a repetition-rate mode.