Optical Heterodyne Research Articles

A novel hybrid radio over fiber visible light communication system combining 5G mmWave and coarse wavelength division multiplex grid

<p>Visible light communication(VLC)has gained attention for enabling gigabitdata transmission over a short-range. Inradio over fiber (RoF), modulatedradio frequency (RF) is carried over optical fiber. Millimeter-wave (mmW)range also offers a vast amount of spectrum and enables integration with RoF.We propose a novel hybrid network using mmWave based RoF backhaulandcoarse wavelength division multiplexed(CWDM)-VLC for indoorcommunication. Three different optical tones were introduced to produce thedesired mmW signal using optical heterodyning with one of them carryingmodulated data and the other two carrying unmodulated data. Opticalsideband signal with the carrier(OSSB+C) is used for uplink communication.Modulated mmWave signal is used for VLC downlink to drive a multi-colorCWDM system. The performance of the VLC downlink is measured usingdifferent optical filters such as Bessel, Trapezoidal, Gaussian, and FabryPerot. A maximum data rate of 2.64 Gb/s and 6.58 Gb/s were achieved with10 and 20channelsoff the shelf LEDs with 16quadrature amplitudemodulation (QAM) with reasonable BER for downlink VLC communication.The uplink communication was carried out using mmW with 2.5 Gb/s datarate usingon-off keying(OOK)modulation and the data from thiscommunication down converted atcentral office(CO) through RoF backhaul.</p>

Integration of Sensing and Communication in a W-Band Fiber-Wireless Link Enabled by Electromagnetic Polarization Multiplexing

The coexistence needs of sensing and communication in millimeter-wave (mmW) bands have urgently driven the seamless integration of sensing and communication in the upcoming mmW era. However, the time-frequency competition between the two functions makes it difficult to accommodate both high sensing resolution and large communication capacity. In this paper, we have designed a W-band fiber-wireless link with the integrated sensing and communication functions enabled by electromagnetic polarization multiplexing. The ultra-wideband fiber-wireless link in W band is enabled by the asymmetrical single-sideband modulation along with the optical heterodyne up-conversion. The electromagnetic polarization multiplexing allocates the sensing and communication functions on two orthogonal electromagnetic polarizations, respectively. Thus, all time-frequency resources of the fiber-wireless link can simultaneously serve these two functions without any resource competition, contributing to an ultra-high spatial resolution and an ultra-large data capacity at the same time. Our experimental results show the spatial resolution of up to 15 mm and data rate as high as 92 Gbit/s were simultaneously realized in W band after delivering over a 10.8-m wireless distance. The overall improvement of both the sensing and communication performance, to the best of our knowledge, led to a record capacity-resolution quotient of 61.333 Gbit/s/cm. In addition, we have qualitatively investigated the integrated sensing and communication fiber-wireless link, in terms of the carrier frequency, system bandwidth, multi-mmW access, and electromagnetic polarization crosstalk.

Photonic generation of a tunable multi-band linearly frequency-modulated waveform

A photonic-assisted tunable multi-band linearly frequency-modulated (LFM) waveform generator based on optical heterodyne detection is proposed and experimentally demonstrated. The multi-band LFM waveform is generated from a photodetector (PD), where a broadband LFM optical pulse and a multi-wavelength optical signal with the same magnitude at different wavelengths are heterodyne-detected. The LFM optical pulse is generated from a three-electrode distributed Bragg reflector laser diode (DBR-LD). The multi-wavelength optical signal is produced through a Mach-Zehnder modulator (MZM), in which a light wave from an optical fiber laser (OFL) is nonlinearly intensity-modulated by a radio frequency (RF) signal. By tuning the wavelength of the LFM optical pulse lower than that of the multi-wavelength optical signal, a multi-band LFM waveform is generated at the PD. The center frequency of the generated LFM waveform can be adjusted by manipulating the wavelength of the OFL. The versatility in the bandwidth and temporal duration of the LFM waveform is attained through the precise tuning of the LFM optical pulse. The tuning of the center frequency difference between frequency bands is performed by altering the frequency of the RF signal. Experimental results have corroborated the realization of a tunable multi-band LFM waveform generator. The bandwidth and temporal duration of each band and the center frequency difference between frequency bands have tuning ranges from 0.7 to 6.7 GHz, 1 to 50 μs, and 2 to 6.7 GHz, respectively. The demonstration shows new avenues to implement high-performance multi-band LFM waveform generators for applications in multi-functional modern radar systems.

Characterization of Laser Frequency Stability by Using Phase-Sensitive Optical Time-Domain Reflectometry

A new method to measure laser phase noise and frequency stability based on the phase-sensitive optical time-domain reflectometry is proposed. In this method, the laser under test is utilized in a phase-sensitive optical time-domain reflectometer, which employs phase-modulated dual pulses and acts as an optical frequency discriminator: laser frequency fluctuations are deduced from the analysis of the reflectometer data corresponded to phase fluctuations along the vibration-damped and thermally insulated fiber spool. The measurement results were validated by comparison with direct optical heterodyning of the tested and more coherent reference lasers. The use of dual pulses generated by an acousto-optic modulator makes it easy to adjust the time delay during measurements, which distinguishes favorably the proposed method from standard optical frequency discriminators. The method is suitable for testing highly coherent lasers and qualifying their parameters such as linear drift rate, random frequency walk rate, white frequency noise (which is directly related to laser instantaneous linewidth), and flicker noise level.

Drift Error Compensation Algorithm for Heterodyne Optical Seawater Refractive Index Monitoring of Unstable Signals.

The refractive index measurement of seawater has proven significance in oceanography, while an optical heterodyne interferometer is an important, highly accurate, tool used for seawater refractive index measurement. However, for practical seawater refractive index measurement, the refractive index of seawater needs to be monitored for long periods of time, and the influence of drift error on the measurement results for these cases cannot be ignored. This paper proposes a drift error compensation algorithm based on wavelet decomposition, which can adaptively separate the background from the signal, and then calculate the frequency difference to compensate for the drift error. It is suitable for unstable signals, especially signals with large differences between the beginning and the end, which is common in actual seawater refractive index monitoring. The authors identify that the primary cause of drift error is the frequency instability of the acousto-optic frequency shifter (AOFS), and the actual frequency difference was measured through experimentation. The frequency difference was around 0.1 Hz. Simulation experiments were designed to verify the effectiveness of the algorithm, and the standard deviation of the optical length of the results was on the scale of 10-8 m. Liquid refractive index measurement experiments were carried out in a laboratory, and the measurement error was reduced from 36.942% to 0.592% after algorithm processing. Field experiments were carried out regarding seawater refractive index monitoring, and the algorithm-processing results are able to match the motion of the target vehicle. The experimental data were processed with different algorithms, and, according to the comparison of the results, the proposed algorithm performs better than other existing drift error elimination algorithms.

Optical heterodyne detection system for a high-speed camera based on the HSA phase compensation method.

This study proposes an innovative active optical heterodyne detection system to address the limitations of existing swarm intelligence algorithms in resolving phase compensation issues within coherent detection systems. The design incorporates a high-speed camera array detector, offering improved practicality and a simplified structure. Employing a heuristic search algorithm (HSA) transforms the high-dimensional problem into multiple one-dimensional optimization problems, significantly enhancing algorithmic running speed. The HSA maintains excellent performance even with increased array elements, allowing for real-time phase correction in large arrays. Experimental results using shot peening comparison samples reveal a substantial amplification of the heterodyne signal spectrum amplitude peak, approximately 60 times greater than the original signal. This innovative approach holds great potential for active optical heterodyne detection of dim targets, paving the way for further research in the field.

In-Situ Detection for Atomic Density in the K-Rb-21Ne Co-Magnetometer via an Optical Heterodyne Interferometry

The low-frequency fluctuations of the atomic density within the cell can induce the longterm drift of the K-Rb-21Ne spin-exchange relaxation-free (SERF) co-magnetometer output, such that the accurate measurement of in situ atomic density is of great significance for improving the performance of co-magnetometer. In this paper, the complex refractive index model of the spin ensembles under the hybrid optical pumping condition is established first, according to which the relation between atomic density and its complex refractive index is revealed and an optical heterodyne-based scheme for atomic density detection is proposed. The dependence of the atomic density on the demodulated phase signal from the optical heterodyne-based scheme is provided by numerical simulations. After that, a dual acousto-optics frequency shifter (AOFS)-based optical heterodyne interferometry is constructed with a noise level below 1 mrad/Hz for frequencies > 1 Hz, and a compact SERF co-magnetometer is implemented as the testing medium, by which the atomic density detection with resolution of 0.40 K @ 473 K is reached and the experimental results agree well with theoretical simulations. Moreover, the detection scheme proposed in this paper has the properties of high detection sensitivity and immunity to laser power fluctuation, which are also proved experimentally.

Factors influencing the performance of optical heterodyne detection system

Factors influencing the performance of optical heterodyne detection system

Fabry-Pérot optical frequency comb based mm-wave RoF system using pilot-assisted equalizer.

The emergence of the millimeter wave (mm-Wave; 30 GHz to 300 GHz) frequency band holds a lot of promise for addressing the congestion at low frequency in future mobile networks. Among many mm-Wave generation schemes, optical heterodyning is considered one of the most promising approaches due to its scalability and potential for integration on chip. Employing optical frequency combs (OFC) for optical heterodyning alleviates the significant phase distortions/noise introduced by the optical sources. However, any residual phase noise in these systems can deteriorate the transmission performance. Here we demonstrate a high-capacity mm-Wave radio-over-fiber (RoF) system using Fabry-Pérot (FP) laser comb overcoming the typical limitations of this source. The temporal phase perturbation induced by the frequency fluctuation of the FP laser is theoretically analyzed, and then estimated and compensated by a pilot-based phase equalizer. Performance evaluation of the proposed phase equalizer is conducted through experiment and simulation. Enabled by the proposed compensation scheme, ten 200 MHz filtered orthogonal frequency division multiplexing (f-OFDM) signal bands modulated by 16-quadrature amplitude modulation (QAM) are transmitted over 10 km fiber, with the ability to serve multiple users. The transmission of 16-QAM modulated single carrier signals with 2 GBd and 8 Gbps data rate is also performed for comparison, which offers better resilience to phase noise, demonstrating the first commercial Quantum Well FP laser-based optical heterodyning mm-Wave RoF system for both multi-carrier and single carrier signals.

Self-calibrated NICE-OHMS based on an asymmetric signal: theoretical analysis and experimental validation.

As an ultra-sensitive detection technique, the noise-immune cavity enhanced optical heterodyne molecular spectroscopy (NICE-OHMS) technique has great potential for assessment of the concentration of trace gases. To determine gas concentrations at the ppt or lower level with high accuracy, it is desirable that the technique exhibits self-calibration (or calibration-free) capabilities. Although being sensitive, NICE-OHMS has so far not demonstrated any such ability. To remedy this, this paper provides a self-calibrated realization of NICE-OHMS that is based on a switching of the feedback target of the DeVoe-Brewer (DVB) locking procedure from the modulation frequency of the frequency modulation spectroscopy (FMS) to the cavity length, which creates an asymmetrical signal whose form and size can be used to unambiguously assess the gas concentration. A comprehensive theoretical model for self-calibrated NICE-OHMS is established by analyzing the shift of cavity modes caused by intracavity absorption, demonstrating that gas absorption information can be encoded in both the laser frequency and the NICE-OHMS signal. To experimentally verify the methodology, we measure a series of dispersion signals under different levels of absorbance using a built experimental setup. An instrument factor and the partial pressure are obtained by fitting the measured signal through theoretical expressions. Our results demonstrate that fitted values are more accurate for higher partial pressures than for lower. To improve on the accuracy at low partial pressures, it is shown that the instrument factor obtained by fitting the signal at large partial pressures (in this case, above 7.8 µTorr) can be set to a fixed value for all fits. By this, the partial pressures can be assessed with a relative error below 0.65%. This technique has the potential to enable calibration-free ultra-sensitive gas detection.

Multi-frequency 5G NR millimeter-wave signal generation over analog RoF link using optical frequency combs

Optical heterodyne analog radio-over-fiber (A-RoF) links can provide a cost-effective and spectrally efficient solution for the generation and distribution of millimeter-wave/Terahertz (mm-wave/THz) carriers for the next-generation wireless systems. The use of an optical frequency comb (OFC) source in such a system can facilitate carrier generation free from frequency fluctuation. However, decorrelation between tones, due to path length difference, can lead to phase noise on the generated mm-wave carrier — limiting the performance of low subcarrier spacing multi-carrier signals specified in the 5G standard. In this work, we analyze the effect of comb tones decorrelation due to path length difference on the performance of 5G compatible 244 kHz subcarrier spacing 59 GHz OFDM signal over an optical heterodyne A-RoF link using a gain switched laser (GSL) OFC source. Furthermore, we demonstrate the ability of the OFC-based A-RoF optical/mm-wave system to support flexible and interoperable mm-wave functionality through signal generation at 27 GHz, 43 GHz and 59 GHz using different pairs of GSL OFC tones for remote heterodyning. The capability of multi-frequency 5G NR compatible mm-wave signal generation and potential for photonic integration make the demonstrated GSL OFC based optical heterodyne A-RoF system a suitable candidate for deployment in the next generation wireless systems.

High sensitive temperature sensor based on narrow band-pass filters via optical heterodyne technique

High sensitive temperature sensor based on narrow band-pass filters via optical heterodyne technique

An integrated photonic-assisted phased array transmitter for direct fiber to mm-wave links

Millimeter-wave (mm-wave) phased arrays can realize multi-Gb/s communication links but face challenges such as signal distribution and higher power consumption hindering their widespread deployment. Hybrid photonic mm-wave solutions combined with fiber-optics can address some of these bottlenecks. Here, we report an integrated photonic-assisted phased array transmitter applicable for low-power, compact radio heads in fiber to mm-wave fronthaul links. The transmitter utilizes optical heterodyning within an electronically controlled photonic network for mm-wave generation, beamforming, and steering. A photonic matrix phase adjustment architecture reduces the number of phase-shift elements from M × N to M + N lowering area and power requirements. A proof-of-concept 2 × 8 phased array transmitter is implemented that can operate from 24–29 GHz, has a steering range of 40°, and achieves 5 dBm EIRP at an optical power of 55 mW without using active mm-wave electronics. Data streams at 2.5 Gb/s are transmitted over 3.6 km of optical fiber and wirelessly transmitted attaining bit-error rates better than 10−11.

Real-Time Ellipsometric Surface Plasmon Resonance Sensor Using Polarization Camera May Provide the Ultimate Detection Limit.

Ellipsometric Surface Plasmon Resonance (SPR) sensors are known for their relatively simple optical configuration compared to interferometric and optical heterodyne phase interrogation techniques. However, most of the previously explored ellipsometric SPR sensors based on intensity measurements are limited by their real-time applications because phase or polarization shifts are conducted serially. Here we present an ellipsometric SPR sensor based on a Kretschmann-Raether (KR) diverging beam configuration and a pixelated microgrid polarization camera. The proposed methodology has the advantage of real-time and higher precision sensing applications. The short-term stability of the measurement using the ellipsometric parameters tanψ and cos(Δ) is found to be superior over direct SPR or intensity measurements, particularly with fluctuating sources such as laser diodes. Refractive index and dynamic change measurements in real-time are presented together with Bovine Serum Albumin (BSA)-anti-BSA antibody binding to demonstrate the potential of the developed sensor for biological sensing applications with a resolution of sub-nM and down to pM with additional optimization. The analysis shows that this approach may provide the ultimate detection limit for SPR sensors.

Photonic super-resolution millimeter-wave joint radar-communication system using self-coherent detection.

A millimeter-wave (MMW) joint radar-communication (JRC) system with super-resolution is proposed and experimentally demonstrated, using optical heterodyne upconversion and self-coherent detection downconversion techniques. The point lies in the designed coherent dual-band constant envelope linear frequency modulation-orthogonal frequency division multiplexing (LFM-OFDM) signal with opposite phase modulation indexes for the JRC system. Then the self-coherent detection, as a simple and low-cost means, is accordingly facilitated for both de-chirping of MMW radar and frequency downconversion reception of MMW communication, which circumvents costly high-speed mixers along with MMW local oscillators and, more significantly, achieves the real-time decomposition of radar and communication information. Furthermore, a super-resolution radar range profile is realized through the coherent fusion processing of dual-band JRC signals. In experiments, a dual-band LFM-OFDM JRC signal centered at 54 GHz and 61 GHz is generated. The two bands feature an identical instantaneous bandwidth of 2 GHz and carry an OFDM signal of 1 Gbaud, which helps to achieve a 6-Gbit/s data rate for communication and a 1.76-cm range resolution for radar.

Photonic Generation of Frequency-Modulated Interrupted Continuous Waveforms

A frequency-modulated interrupted continuous waveform (FMICW) generator with an ultra-large bandwidth based on optical heterodyne detection is proposed and experimentally demonstrated. The FMICW generator is implemented through the heterodyne detection of a stable optical carrier and a gate-function-modulated frequency-chirped optical pulse. A stable sub-kHz optical fiber laser operates the optical carrier. The optical pulse is generated from a three-electrode distributed Bragg reflector (DBR) laser diode (LD), which is gate-function modulated by a current source via the passive phase control section. By beating the optical carrier and the optical pulse at a photodetector (PD), an FMICW is generated. The bandwidth of the FMICW is over 20 GHz, and the temporal duration is around 200 <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$\mu \text{s}$ </tex-math></inline-formula> . The compression ratio is obtained as large as <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$3.78\times 10 ^{6}$ </tex-math></inline-formula> . Thanks to the tunability of the gate-function-modulated frequency-chirped optical pulse, the generated FMICW is fully tunable in terms of gate-function period and duty ratio.

Investigation of high-precision seawater refractive index sensor based on optical heterodyne interference

Investigation of high-precision seawater refractive index sensor based on optical heterodyne interference

The Influence of Temperature on Frequency Modulation Spectroscopy in Atom Gravimeter.

Atom gravimeters use locked lasers to manipulate atoms to achieve high-precision gravity measurements. Frequency modulation spectroscopy (FMS) is an accurate method of optical heterodyne spectroscopy, capable of the sensitive and rapid frequency locking of the laser. Because of the effective absorption coefficient, Doppler broadening and susceptibility depend on temperature, and the signal-to-noise ratio (SNR) of the spectroscopy could be affected by temperature. We present a detailed study of the influence of the temperature on FMS in atom gravimeters, and the experimental results show that the SNR of the spectroscopy is dependent on temperature. In this paper, the frequency of the reference laser is locked by tracking the set point of the fringe slope of FMS. The influence of the frequency-locking noise of the reference laser on the sensitivity of the atom gravimeter is investigated by changing the temperature of the Rb cell without extra operations. The method presented here could be useful for improving the sensitivity of quantum sensors that require laser spectroscopic techniques.

Optical-resolution functional gastrointestinal photoacoustic endoscopy based on optical heterodyne detection of ultrasound

Photoacoustic endoscopy shows promise in the detection of gastrointestinal cancer, inflammation, and other lesions. High-resolution endoscopic imaging of the hemodynamic response necessitates a small-sized, high-sensitivity ultrasound sensor. Here, we utilize a laser ultrasound sensor to develop a miniaturized, optical-resolution photoacoustic endoscope. The sensor can boost the acoustic response by a gain factor of ωo/Ω (the frequency ratio of the signal light and measured ultrasound) by measuring the acoustically induced optical phase change. As a result, we achieve a noise-equivalent pressure density (NEPD) below 1.5 mPa·Hz-1/2 over the measured range of 5 to 25 MHz. The heterodyne phase detection using dual-frequency laser beams of the sensor can offer resistance to thermal drift and vibrational perturbations. The endoscope is used to in vivo image a rat rectum and visualize the oxygen saturation changes during acute inflammation, which can hardly be observed with other imaging modalities.

Photonic Integrated Circuit for Optical Phase Control of 1 × 4 Terahertz Phased Arrays

In this manuscript, we report on a 1 × 4 optical beam forming network (OBFN) chip using optical phase shifters (OPSs) based on thermo-optically controlled optical ring resonators (ORRs) for 1D beam steering at 0.3 THz. The 1 × 4 OBFN chip consists of four OPSs and is fabricated using TriPleX technology. Each of the four OPSs is realized by two cascaded identical ORRs, to reach a phase shift of 2π. To allow transfer of the optical phase shift to the THz domain by optical heterodyning in high-frequency 1.55 µm modified uni-travelling carrier photodiodes, the ORRs are designed such that one carrier of the optical heterodyne signal is at the ORR’s resonance frequency, whereas the second optical heterodyne signal is at its off-resonance. By adjusting the resonance frequencies of the two ORRs in each OPS synchronously, a relative phase variation between two optical heterodyne carriers of up to 2π with a tuning efficiency of 0.058 W/π, is experimentally demonstrated. Due to the dispersive power transmission loss of the ORRs, phase tuning leads to a power variation of the optical heterodyne-generated signals up to 3.8 dB, which is experimentally characterized at 0.295 THz. It is shown numerically that this power variation only has a minor impact on the steering performance of a 1 × 4 phased array. The determined beam direction deviation and maximum absolute radiation power change are smaller than 1° and 2 dB, respectively. By sweeping the phase difference between two adjacent THz antennas in the 1 × 4 phased array, from −120° to 120°, a beam steering range of ~62° is demonstrated numerically at 0.295 THz.