Optical Strain Measurement Research Articles

A non-contact optical uniaxial tension-unloading strain measurement

A tension-compression test is necessary to investigate the impact of the kinematic hardening model’s parameters on the springback following sheet metal stamping processes. However, conventional cyclic testing using extensometers faces challenges due to buckling issues. Therefore, the implementing of Digital Image Correlation (DIC), a non-contact optical measurement system, becomes crucial. The present investigation involved the simultaneous use of an extensometer and an AutoGrid optical strain measurement system to perform a uniaxial tension-unloading test on aluminum alloy AA6082-T6. Both measurement systems were evaluated based on the comparison of the time-displacement, time-force, true stress-true strain, and reduction of Young’s modulus due to deformation. The results show that the force, change in displacement, and stress-strain values obtained by the two measurement techniques are comparable and close. It demonstrates that the DIC method has high accuracy and moderate agreement with conventional extensometer.

An in vitro biomechanical evaluation of integrated lateral plate combined with oblique lateral interbody fusion in different bone conditions

Oblique lateral interbody fusion (OLIF) is a minimally invasive surgery for the treatment of lumbar degenerative diseases (LDD). Under normal bone mass(NB), supplemental with lateral plate (LP) fixation has been proven to provide stability and reduce complications. However, it is unclear whether OLIF combined with LP fixation can achieve satisfactory fixation effects in cases of osteoporosis(OP) or osteopenia (OS)? In this study, Eighteen L3-5 spinal specimens from 3 to 6 months old fresh calves were equally divided into 3 groups: group A (NB), group B (OS) and group C (OP). A load control scheme was adopted and evaluated using multidirectional nondestructive moments (± 7.5 N·m). An electronic universal tester and a tensile/torsion tester were simulated to generate 6 degrees of freedom of motion, and a VIC-3D three-dimensional optical full-field strain measurement system dynamically tracked the surgical segmental displacement. Each spine was evaluated under the following conditions at the L4-5 level: intact (INT); OLIF stand-alone (SA); cage supplemented with LP, cage supplemented with unilateral pedicle screws (UPS), and cage supplemented with bilateral pedicle screws (BPS). The current data show that With NB and OS models, LP fixation significantly reduced ROM in the LB and AR directions, with slightly less stability than BPS fixation and comparable to UPS. In the case of OP, LP fixation may increase the risk of internal fixation failure, and it is more preferable to choose BPS fixation with stronger stability.

Field monitoring and prediction of the thermal response of an in-service curved continuous welded rail using distributed fiber optic strain measurements

Field monitoring and prediction of the thermal response of an in-service curved continuous welded rail using distributed fiber optic strain measurements

Geomechanics Modeling of Strain-Based Pressure Estimates: Insights from Distributed Fiber Optic Strain Measurements

Summary Rayleigh frequency shift distributed strain sensing (RFS-DSS) has been demonstrated as a potential technology for characterizing fracture geometries and optimizing the completion design in unconventional reservoirs. The combination of RFS-DSS strain and pressure gauge measurements has been reported recently in field applications (Dhuldhoya and Friehauf 2022; Haustveit and Haffener 2023) to characterize conductive fracture dimensions and production profiles. Haustveit and Haffener (2023) demonstrated a novel technique that uses RFS-DSS strain change during production, measured from a far-field observation well, to monitor the drain profile of a horizontal multistage well. The strain change and pressure change were strongly related during production, and this relationship was applied to continuously estimate pressure drawdown along the full length of the well. However, the sensitivity or influencing factors of the relationship between strain change and pressure change along the fiber are not yet fully understood. Therefore, the main objective of this study is to investigate the relationship between strain change and pressure change under various fractured reservoir conditions and provide guidelines for better utilizing this novel strain-pressure relationship to estimate conductive fractures and pressure profiles. We use a coupled geomechanics and fluid flow model to simulate the strain and pressure changes in the near-well and far-field regions during stable production and shut-in periods. A linear relationship is used to fit the strain change and pressure change data obtained from both producing and monitoring wells. We analyze the impact of various fracture properties [size and permeability of the stimulated reservoir volume (SRV) around fractures, fracture conductivity, fracture area, and skin factor] on the linear relationship based on the R2 value and fitting error. The relationship between the strain change and pressure change during the stable production obtained by our numerical study is consistent with the field measurements. The slope of strain change vs. pressure change during one day of production is significantly influenced by fracture properties. Overall, the monitoring well shows a stronger linear relationship than the producing well during both stable production and shut-in periods. A better linear relationship between the strain change and pressure change is associated with a larger fracture conductivity or larger fracture spacing scenario on both producing and monitoring wells during the stable production period. The cluster spacing affects the linear relationship between strain and pressure change during rock deformation. When cluster spacing is reduced, the nonlocal effect of deformation becomes more pronounced, resulting in a weaker linear relationship. During the shut-in period, the monitoring well exhibits a stronger linear relationship with a high R2 value and small fitting error compared to the producing well. The linear relationship obtained during the shut-in period is less reliable for the producing well. In cases of homogeneous fractures, where the fracture properties are uniform, the strain change and pressure change are similar, except for two outer fractures. This study provides a better understanding of the relationship between strain change and pressure change measured in the near-well and far-field regions during stable production and shut-in periods. The results of our study also demonstrate the potential for utilizing the RFS-DSS strain measurement to characterize the effective fracture and drainage dimensions.

The Impact of Liquids and Saturated Salt Solutions on Polymer-Coated Fiber Optic Sensors for Distributed Strain and Temperature Measurement.

The application of distributed fiber optic strain and temperature measurement can be utilized to address a multitude of measurement tasks across a diverse range of fields, particularly in the context of structural health monitoring in the domains of building construction, civil engineering, and special foundation engineering. However, a comprehensive understanding of the influences on the measurement method and the sensors is essential to prevent misinterpretations or measurement deviations. In this context, this study investigated the effects of moisture exposure, including various salt solutions and a high pH value, on a distributed strain measurement using Rayleigh backscattering. Three fiber optic sensors with different coating materials and one uncoated fiber were exposed to five different solutions for 24 h. The study revealed significant discrepancies (∼38%) in deformation between the three coating types depending on the surrounding solution. Furthermore, in contrast to the prevailing literature, which predominantly describes swelling effects, a negative deformation (∼-47 με) was observed in a magnesium chloride solution. The findings of this study indicate that corresponding effects can impact the precision of measurement, potentially leading to misinterpretations. Conversely, these effects could be used to conduct large-scale monitoring of chemical components using distributed fiber optic sensing.

Dual-actuator mixed-mode bending tests on structural adhesive joints

In this article, a novel mixed-mode bending (MMB) test setup is presented and used to investigate the fracture behavior of the structural adhesive SikaPower®-498. The novelty lies in the implementation of two actuators that can be controlled independently of each other. This opens up investigation possibilities that go beyond those of the MMB standard configuration. For example, a varying mode-mixity can be prescribed during testing, allowing identification of an entire fracture envelope from a single experiment. Additionally, an optical fiber strain measurement (OFS) system is used to determine the curvatures of the substrates, allowing for a detection of the actual crack tip position and an analysis of the loading conditions behind the crack tip. The presented work focuses on the experimental calibration of the compliance change during crack growth, on tests performed at constant (external) mode-mixity using a mode partitioning approach based on the J-integral, as well as on tests carried out under varying mode-mixity. Additional aspects of the test setup such as stable crack growth regime or differences between the results of different evaluation methods are discussed. Finally, the obtained fracture envelopes are compared with references from literature, including for the first time a comparison between mixed-modes I+II and I+III.

Advanced methods for the detection of measurement outliers in fibre optic strain measurements for non-destructive monitoring of the structural health of composite over-wrapped pressure vessels of type-IV

To analyse the applicability of fibre optic measurements as a measurement method for structural health monitoring, fibre-optic sensors are placed on the vessel surface. The influence of the surface profile of the vessel on the measurement result is analysed by correlating the 3D scanned surface and measurement results. One outcome is that the measurement is substantially influenced by the surface topography. The surface height can be directly correlated to the strain magnitude, which is also verified by analytical calculations. Outliers and invalid values can be traced back to surface-related influences on the sensor fibre. For the outlier detection, a novel method is presented, which is based on quantitative evaluation criteria and inductive reasoning and enables transient cycle- by-cycle outlier detection adapted to the load case. Based on the results an estimate for the expanded measurement uncertainty is given for of the measurement chain consisting of vessel, adhesive and sensor fibre.

A technique for estimation of cyclic stress-strain curves using an optical strain measurement and its application to additively manufactured AlSi10Mg

The article describes a new accelerated technique for estimation of cyclic stress-strain curves of cyclically stable materials based on a full-field measurement of strain during low-cycle testing on a large amplitude of loading. Any optical method suitable for capturing the strain contours on the curved part of the specimen during cyclic loading is applicable in the approach developed. In this study, the digital image correlation method is used to measure the deformation on the curved part of the specimen. The technique is presented on chosen results of low-cycle fatigue tests performed on AlSi10Mg printed with selective laser melting technology. Proportional loading cases were performed in tension-compression and pure torsion. The case of non-proportional loading was realized in the form of 90 degree out-of-phase tests. The stress-strain behavior is evaluated using a standard procedure and an accelerated technique with a good correlation for the three loading cases.

Optical strain measurements during pulsed laser beam welding to improve the understanding of hot crack formation of EN AW-6082 aluminum alloy

E-mobility turned in the last years to be an emerging market and one solution to fossil fuel free mobility for the future. E-mobility requires, compared to fossil-fueled mobility concepts, a huge amount of welding tasks, which have to guarantee different functionality, as for example high strength, ductility, but also low resistivity and tightness. Last is especially for housing or cases of aluminum in automotive challenging, as pores and cracks can occur. Pulsed laser welding presents, due to the adaptable heat input and the temporal modification of stress state and solidification conditions advantages for this type of applications. EN AW-6xxx group of aluminum alloys is mainly used for such components due to their favorable mechanical properties. However, these alloys are susceptible to hot cracking during solidification from the molten phase. This article aims to present a methodology for demonstrating the resulting strain during pulsed laser beam welding of hot crack susceptible aluminum alloys. It will highlight the influence of factors such as pulse shape, shielding gas, and flow rate on strain and strain rate.

Efficiency evaluation of a commercial superficial strengthening system applied to AAC-block walls under diagonal compression

The article presents the influence of a superficial strengthening system on the behaviour of AAC-block walls with thin bed joints and unfilled head joints. The strengthening system consisted of a high-strength fibreglass mesh applied to both wall surfaces with a mineral mortar reinforced with fibreglass. A series of strengthened and unstrengthened specimens was tested under diagonal compression according to ASTM E519-15 to determine their shear strength and stress-strain characteristics. The use of optical strain measurement made it possible to identify the failure mode for both types of the tested walls. The strengthening system changed the wall failure development, which was initiated by unfilled head joints in both cases. The application of the strengthening system on both wall surfaces improved the strength properties of the wall significantly. The load-bearing capacity of the specimens increased by nearly 90% and cracking of the walls occurred at loads about 50% higher compared to specimens with no superficial strengthening. The strengthened specimens exhibited a ductile behaviour after reaching the maximum bearing capacity. A simplified method for computing the cracking load and maximum load was also proposed, the results of which are consistent with the tests results.

Optical full-field strain measurement within a diamond anvil cell.

Digital image correlation computations are run on optical images of iron samples within a diamond anvil cell to obtain in-plane strain components at the surface of the sample up to 17GPa. The α-Fe → ε-Fe transition onset pressure and phase coexistence pressure domain can be identified from the evolution of the surface average of strain components. Strain fields exhibit localizations for both direct and reverse transition; they coincide with the approximate boundary locations of reversion variants inside the microstructure of a single crystal sample. The so-called DICDAC (Digital Image Correlation within a Diamond Anvil Cell) setup is then a suitable tool for the investigation of phase transformations strains under pressure. In addition, specific volumes that are deduced from strain out of the transition pressure domains agree within ΔV/V = 0.4% with the equation of state data from the literature.

The Challenges and Advantages of Distributed Fiber Optic Strain Monitoring in and on the Cementitious Matrix of Concrete Beams

Distributed fiber optic strain measurement techniques have become increasingly important in recent years, especially in the field of structural health monitoring of reinforced concrete structures. Numerous publications show the various monitoring possibilities from bridges to special heavy structures. The present study is intended to demonstrate the possibilities, but also the challenges, of distributed fiber optic strain measurement in reinforced concrete structures. For this purpose, concrete beams for 3-point bending tests were equipped with optical fibers on the reinforcement and concrete surface as well as in the concrete matrix in order to record the strains in the compression and tension zone. In parallel, an analytical approach based on the maximum strains in the uncracked and cracked states was performed using the Eurocode 2 interpolation coefficient. In principle, the structural design correlates with the measured values, but the strains are underestimated, especially in the cracked zone. During load increase, structural distortions in the compression zone affected the strain signal, making reliable evaluation in this zone difficult. The information content of distributed fiber optic strain measurement in reinforced concrete structures can offer tremendous opportunities. Future research should consider all aspects of the bond, sensor selection and positioning. In addition, there is a lack of information on the long-term stability of the joint and the fiber coating, as well as the effects of dynamic loading.

Fracture toughness of freestanding plasma sprayed yttria stabilized zirconia coatings via in situ tensile experiments

Tensile response and fracture toughness of the freestanding atmospheric plasma spray 8YSZ coatings was investigated using in situ high resolution optical full-field strain measurement. The elastic properties obtained directly from the tensile experiments were employed in computing the critical mode-I stress intensity factor. Comparison between the fracture toughness values computed from specimen geometry and J-integral via displacement field around the crack tip showed small differences on single edge notched tensile (SENT) specimens to extract their intrinsic mode-I fracture toughness. Two kinds of coatings having different porosity were studied to obtain stress-strain response and compute effect of porosity on mode-I fracture toughness. The samples were fabricated by depositing the coatings on, un-notched and pre-notched substrate templates, and then carefully separating the coatings by acidic dissolution of the substrate. High resolution in situ deformation of the coatings was captured for both tensile and SENT specimens using digital image correlation method combined with an in-house designed microtensile stage. The deformation from the specimen surface was used to obtain elastic material properties under uniaxial tension, which are then used to compute the energy release rate by the path independent J-integral. The critical stress intensity factors calculated from SENT geometry for the low and high porosity coatings were found to be 1.23 ± 0.21 MPa-m0.5 and 0.67 ± 0.12 MPa-m0.5, respectively. In addition, considering the experimental observation of nucleation and propagation of a crack from the notch tip before catastrophic failure, the J-integral based calculation of the critical fracture toughness values were 1.37 ± 0.19 MPa-m0.5 and 0.5 ± 0.1 MPa-m0.5, for the low and high porosity coatings, respectively. As the crack always nucleates from the notch before complete fracture, it can be concluded that the J-integral based method is accurate and suitable for finding the fracture toughness in porous coatings.

Buckling Analysis of Thin-Walled Composite Structures with Rectangular Cross-Sections under Compressive Load.

The purpose of this research was the analysis of the stability of compressed thin-walled composite columns with closed rectangular cross-sections, subjected to axial load. The test specimens (made of carbon-epoxy composite) were characterized by different lay-ups of the composite material. Experimental tests were carried out using a universal testing machine and other interdisciplinary testing techniques, such as an optical strain measurement system. Simultaneously with the experimental studies, numerical simulations were carried out using the finite element method. In the case of FEA simulations, original numerical models were derived. In the case of both experimental research and FEM simulations, an in-depth investigation of buckling states was carried out. The measurable effect of the research was to determine both the influence of the cross-sectional shape and the lay-up of the composite layers on the stability of the structure. The novelty of the present paper is the use of interdisciplinary research techniques in order to determine the critical state of compressed thin-walled composite structures with closed sections. An additional novelty is the object of study itself-that is, thin-walled composite columns with closed sections.

Visualizing multi-physical spatiotemporal evolution of dielectric breakdown in high-performance polymeric capacitors

Pulse power has many important technological applications, for which the dielectric capacitors are essential. It is imperative to understand the breakdown mechanism to improve the dielectric energy storage density, yet the breakdown process involves multi-physical coupling spanning multiple spatial and temporal scales, making its characterization very challenging. Recognizing local field concentration results in local strain concentration through Maxwell's stress, we develop an effective method to visualize the dielectric breakdown process via optic strain measurement. Utilizing high-performance biaxially oriented polypropylene as a demonstration, we find dielectric breakdown is an ultrafast process with breakdown current rising and dropping in just tens of nanoseconds. Rapid temperature rise is observed after breakdown as well due to Joule heating, though both current measurement and temperature mapping offer little insight before breakdown actually occurs. Nevertheless, substantial strain concentration is observed before breakdown, reflecting electric field concentration that eventually leads to breakdown. A well-defined upper bound on the electric field concentration is also noted.

Mechanical properties evaluation of metacarpophalangeal joint prosthesis with new titanium-nickel memory alloy: a cadaver study

ObjectiveNi-Ti memory alloys are unusual materials for hard-tissue replacement because of their unique superelasticity, good biocompatibility, high strength, low specific gravity, low magnetism, wear resistance, corrosion resistance and fatigue resistance. The current study aims to evaluate its mechanical properties and provide biomechanical basis for the clinical application of the prosthesis.MethodsTen adult metacarpophalangeal joint specimens were randomly divided into a prosthesis group (n = 5, underwent metacarpophalangeal joint prosthesis) and a control group (n = 5, underwent sham operation). Firstly, the axial compression strength was tested with BOSE material testing machine to evaluate its biomechanical strength. Secondly, these specimens were tested for strain changes using BOSE material testing machine and GOM non-contact optical strain measurement system to evaluate the stress changes. Thirdly, fatigue test was performed between groups. Lastly, the mechanical wear of the metacarpophalangeal joint prosthesis was tested with ETK5510 material testing machine to study its mechanical properties.ResultsAxial compression stiffness in the prosthesis group was greater than that in the control group in terms of 30 ° and 60 ° flexion positions (P < 0.05). There was no statistically significant difference between two groups with regards to axial compression stiffness and stress change test (P > 0.05). In the fatigue wear test, the mean mass loss in the prosthesis group’s prosthesis was 17.2 mg and 17.619 mm3, respectively. The mean volume wear rate was 0.12%. There was no statistically significant difference in the maximum pull-out force of the metacarpal, phalangeal, and polymer polyethylene pads between the prosthesis group and the control group specimens.ConclusionsNi-Ti memory alloy metacarpophalangeal joint prosthesis conforms to the biomechanical characteristics of metacarpophalangeal joints without implants, and the fatigue strength can fully meet the needs of metacarpophalangeal joint activities after joint replacement.

Heat management and tensile strength of 3 mm mixed and matched connections of butt joints of S355J2+N, S460MC and S700MC

AbstractHigh‐strength structural steels are beneficial in terms of the sustainability of constructions due to the possible reduction of weight and overall material needs. Nevertheless, high‐strength steels have a smaller processing parameter range in regarding the specific heat input and resulting cooling rate. Especially the cooling time t8/5 characterizing the time span to cool down from 800 to 500 °C is an important indicator. Single layer butt‐welded gas metal arc welding (GMAW) connections of 3 mm plates between normal strength (S355J2+N, S460MC) and high‐strength steels (S700MC) as well as matched connections (S460MC, S700MC) are carried out. Hereby, the influence of the energy input, melting rate, joint preparation, filler metal (matching and undermatching) and backing methods are observed. Spatially resolved IR‐thermal observation shows variations within the welds of up to 50 % in the cooling time t8/5 depending on those parameters. These fluctuations lead to significant changes of the microstructure within the melting and heat‐affected zone. UCI hardness mappings show the softening and microstructural change within these zones. Those soft zones can be the region of failure for butt welded connections as shown by transverse tensile tests with spatially resolved optical strain measurements. The results obtained can be used to define more precise welding procedures of these types of connections and also are used to develop design rules for mixed connections made of normal strength and high‐strength steel.

Investigating Damage Mechanisms in Cord-Rubber Composite Air Spring Bellows of Rail Vehicles and Representative Specimen Design

Cord-rubber materials are used in crucial components of rail vehicles, such as air spring bellows in secondary suspension. A detailed understanding of the material behaviour of these components is thus of the utmost importance at an early stage of development. In general, a minor knowledge of the fatigue behaviour is currently all that is available today, while empirical methods involving designer experiences are in most cases essential requirements for this work. The design can be carried out more efficiently based on a representative cord-rubber composite specimen than on an entire air spring bellow. In this paper, the design of such representative specimens is shown taking different geometries and test conditions into consideration. It is found, that a flat specimen design is suitable for analysing the base material under different loading scenarios. The design and optimisation of the specimen geometry was carried out using finite element analysis, which was validated by means of optical strain measurement. The test procedure for the specimen was designed to provide a sound transferability to experimental testing of the components. A fracture pattern study was carried out using radiography and micro computed tomography. The results show, that the dominant damage mechanism is the separation of the layers from each other, denoted as delamination. In conclusion, the developed specimen is well suited for further investigations of the composite material. Furthermore, it will significantly accelerate the development of new air springs and new layups in particular. Future work will focus on a systematic investigation of the fatigue behaviour of the cord-rubber composite air-spring bellows based on the fatigue data of the representative specimens designed in this work.

Space tether system state estimation using distributed fibre optical strain measurement, inverse finite element method and Kalman filter

This paper proposes a robust finite element Kalman filter for the state estimation of flexible space tether systems, which are critical for space exploration and satellite missions. Due to the limited access to placing sensors along the flexible tether to measure them directly, the measurement of the state of these systems is challenging. To address this, a fully expandable, scalable, and robust approach is developed that fuses position/velocity sensors at tether ends, distributed fiber optic strain measurement along the tether, and a position/velocity estimation by a finite element-based Kalman filter to estimate the state of the tether system. The proposed estimator is mathematically proven to be observable, stable, and robust. The effectiveness of the estimator is demonstrated through numerical simulations of a space tether system in orbit, and the method can be extended to any flexible body system. The results of the simulations show that the proposed approach can accurately estimate the state of the tether system, even in the presence of disturbances and noise.

Long-wave infrared photothermoelectric detectors with ultrahigh polarization sensitivity

Filter-free miniaturized polarization-sensitive photodetectors have important applications in the next-generation on-chip polarimeters. However, their polarization sensitivity is thus far limited by the intrinsic low diattenuation and inefficient photon-to-electron conversion. Here, we implement experimentally a miniaturized detector based on one-dimensional tellurium nanoribbon, which can significantly improve the photothermoelectric responses by translating the polarization-sensitive absorption into a large temperature gradient together with the finite-size effect of a perfect plasmonic absorber. Our devices exhibit a zero-bias responsivity of 410 V/W and an ultrahigh polarization ratio (2.5 × 104), as well as a peak polarization angle sensitivity of 7.10 V/W•degree, which is one order of magnitude higher than those reported in the literature. Full linear polarimetry detection is also achieved with the proposed device in a simple geometrical configuration. Polarization-coded communication and optical strain measurement are demonstrated showing the great potential of the proposed devices. Our work presents a feasible solution for miniaturized room-temperature infrared photodetectors with ultrahigh polarization sensitivity.