Open-source Computational Fluid Dynamics Software Research Articles

3D CFD simulation of bottle emptying processes

A 3D Computational Fluid Dynamics (CFD) approach is used to investigate the effect of parameters such as bottle geometry, surface tension, or inclination on bottle emptying processes. The method can e.g. be used to assess changes of bottle emptying times induced by new bottle shapes, and it is shown to be much more accurate than existing empirical models. While expensive commercial CFD software has substantially restricted and hindered the use of this method in the past, our approach is based on freely available open source CFD software and hence accessible to everyone.

Open-Source CFD Simulations of Liquid–Liquid Flow in the Annular Centrifugal Contactor

Simulation of the fluid dynamics of solvent extraction in centrifugal contactors requires advanced models to account for complex physical phenomena including turbulent free-surface flow and liquid-liquid dispersion physics. The use of an open-source computational fluid dynamics (CFD) framework allows for implementation of advanced models not feasible in commercial CFD applications. The open-source CFD package OpenFOAM has been used to simulate turbulent, multiphase flow in the annular centrifugal contactor, including simulations of the mixing zone (annular region), and of the coupled operation of the mixing and separation (rotor interior) zones. These simulations are based on the Volume of Fluid (VOF) methodology along with Large Eddy Simulation (LES) for turbulence. The results from these simulations compare favorably with previous simulations using a commercial CFD tool and with available experimental data. They also give insight into the requirements for more advanced multiphase models needed to accurately capture flows in these devices.

Wind modelling for wind erosion research by open source computational fluid dynamics

The open source computational fluid dynamics (CFD) wind model (CFD-WEM) for wind erosion research in the Xilingele grassland in Inner Mongolia (autonomous region, China) is compared with two open source CFD models Gerris and OpenFOAM. The evaluation of these models was made according to software technology, implemented methods, handling, accuracy and calculation speed. All models were applied to the same wind tunnel data set. Results show that the simplest CFD-WEM has the highest calculation speed with acceptable accuracy, and the most powerful OpenFOAM produces the simulation with highest accuracy and the lowest calculation speed. Gerris is between CFD-WEM and OpenFOAM. It calculates faster than OpenFOAM, and it is capable to solve different CFD problems. CFD-WEM is the optimal model to be further developed for wind erosion research in Inner Mongolia grassland considering its efficiency and the uncertainties of other input data. However, for other applications using CFD technology, Gerris and OpenFOAM can be good choices. This paper shows the powerful capability of open source CFD software in wind erosion study, and advocates more involvement of open source technology in wind erosion and related ecological researches.

Mass transfer and shear in an airlift bioreactor: Using a mathematical model to improve reactor design and performance

Several studies have shown a strong relationship between morphology and agitation ( Cui et al., 1997; Berzins et al., 2001). The shear stress distribution and mass transfer are the important parameters which can improve the performance of bioreactor. In this work, a mathematical model using computational fluid dynamics (CFD) techniques is used to study the gas–liquid dispersion in an airlift reactor. Multiple rotating frame (MRF) technique is used to approximate the movement of the impeller in the stationary reactor. Population balance modeling (PBM) is used to describe the dynamics of the time and space variation of bubble sizes in the reactor. The PBM equation is solved using an approximate method known as the class method (CM) and the bubble sizes are approximated through a discrete number of size ‘bins’, including transport, and different bubble phenomena. These equations of the CM are then written as scalar transport equations and added to the multiphase fluid mechanical equations describing the dynamics of the flow. All these equations are solved using control volume formulation through the use of an open-source CFD package OpenFOAM. The model is used to analyze an existing geometry of an airlift bioreactor and validate the modification on the initial design. The new design of airlift gives a clear performance by the increase of the global and local mass transfer and the decrease of the shear stress.

Viscoelastic flow analysis using the software OpenFOAM and differential constitutive equations

Abstract Viscoelastic fluids are of great importance in many industrial sectors, such as in food and synthetic polymers industries. The rheological response of viscoelastic fluids is quite complex, including combination of viscous and elastic effects and non-linear phenomena. This work presents a numerical methodology based on the split-stress tensor approach and the concept of equilibrium stress tensor to treat high Weissenberg number problems using any differential constitutive equations. The proposed methodology was implemented in a new computational fluid dynamics (CFD) tool and consists of a viscoelastic fluid module included in the OpenFOAM, a flexible open source CFD package. Oldroyd-B/UCM, Giesekus, Phan-Thien–Tanner (PTT), Finitely Extensible Nonlinear Elastic (FENE-P and FENE-CR), and Pom–Pom based constitutive equations were implemented, in single and multimode forms. The proposed methodology was evaluated by comparing its predictions with experimental and numerical data from the literature for the analysis of a planar 4:1 contraction flow, showing to be stable and efficient.

Remark on algorithm perm

The solid oxide fuel cell is an electro-chemical device which converts chemical energy into electricity and heat. To compete in today’s market, design improvements, in terms of performance and life cycle, are required. Numerical prototypes can accelerate design and development progress. In this programme of research, a three-dimensional solid oxide fuel cell prototype, openFuelCell, based on open-source computational fluid dynamics software was developed and applied to a single cell. Transport phenomena, combined with the solution to the local Nernst equation for the open-circuit potential, as well as the Kirchhoff–Ohm relationship for the local current density, allow local electro-chemistry, fluid flow, multi-component species transport, and multi-region thermal analysis to be considered. The underlying physicochemical hydrodynamics, including porous-electrode and electro-chemical effects are described in detail. The openFuelCell program is developed in an object-oriented open-source C++ library. The code is available at http://openfuelcell.sourceforge.net/. The paper also describes domain decomposition techniques considered in the context of highly efficient parallel programming.